Search NASA⌕ Search

SEARCH · Search NASA

Results for “capillary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Fundamentals of Using Cracked Film Lithography to Pattern Transparent Conductive Metal Grids for Photovoltaics

The fundamentals of using cracked film lithography (CFL) to fabricate metal grids for transparent contacts in solar cells were studied. The underlying physics of drying-induced cracks were well-predicted by an empirical correlation relating crack spacing to capillary pressure. CFL is primarily controlled by varying the crack template thickness, which establishes a three-way tradeoff between the areal density of cracks, crack width, and spacing between cracks, which in turn determine final grid transmittance, grid sheet resistance, and the semiconductor resistance for a given solar cell. Since CFL uses a lift-off process, an additional constraint is that the metal thickness must be less than 1/3 of the crack template thickness. Furthermore, the transmittance/grid sheet resistance/wire spacing tradeoffs measured in this work were used to calculate solar cell performance: CFL-patterned grids should outperform screen-printed grids for narrow cells (0.5–2 cm wide) and/or cells with high semiconductor sheet resistance (=100 O/sq), making CFL attractive for monolithically integrated thin-film photovoltaic modules.

14 SOLAR ENERGY↗
DOE OSTI2020

Confinement-mediated phase behavior of hydrocarbon fluids: Insights from Monte Carlo simulations

The phase behavior of hydrocarbon fluids confined in porous media has been discussed to deviate significantly from that in the bulk environment due to the existence of sub-10nm pores. Though experiments and simulations have measured the bubble/dew points and sorption isotherms of hydrocarbons confined in both natural and synthetic nanopores, the confinement effects in terms of the strength of fluid-pore interactions tuned by surface wettability and chemistry have received comparably less discussion. More significantly, the underlying physics of confinement-induced phenomena remain obfuscated. In this work, we studied the phase behavior and capillary condensation of n-hexane to understand the effects of confinement at the molecular level. To systematically investigate the pore effects, we constructed two types of wall confinements; one is a structureless virtual wall described by the Steele potential and the other one is an all-atom amorphous silica structure with surface modified by hydroxyl groups. Our numerical results demonstrated the importance of fluid-pore interaction, pore size, and pore morphology effects in mediating the pressure-volume-temperature (PVT) properties of hydrocarbons. The most remarkable finding of this work was that the saturation pressure predicted from the van der Waals-type adsorption isothermal loop could be elevated or suppressed relative to the bulk phase, as illustrated in the graphical abstract. As the surface energy (i.e., fluid-pore interaction) decreased, the isothermal vapor pressure increased, indicating a greater preference for the fluid to exist in the vapor state. Sufficient reduction of the fluid-pore interactions could even elevate the vapor pressure above that of the bulk fluid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Fractal Model for Drag Reduction on Multiscale Nonwetting Rough Surfaces

Rough surfaces in contact with a flow of fluid exhibit alternating no-slip and free shear boundary conditions at the solid–liquid and air–liquid interfaces, respectively, thereby potentially offering drag reduction benefits. The balance between the dynamic pressure in the flow and the restoring capillary pressure in the interasperity spaces determines the stability of the Cassie state of wettability and is a function of the relative extent of no-slip and free shear regions per unit surface area. In the present study, using a fractal representation of rough surface topography, an analytical model is developed to quantify the stability of the Cassie state of wettability as well as drag reduction and the friction factor for laminar flow in a rectangular channel between nonwetting multiscale rough surfaces. A systematic study is conducted to quantify the effects of fractal parameters of the surfaces and the flow Reynolds number on drag reduction and the friction factor. The studies are used to develop friction factor curves extending the classical Moody diagram to hydrophobic and superhydrophobic surfaces. On the basis of the studies, regime maps are derived for estimating the extent of drag reduction offered by hydrophobic and superhydrophobic surfaces, revealing that superhydrophobic surfaces do not always offer the best drag reduction performance. The application of the fractal model to practical topographies of nonwetting surfaces of copper, aluminum, and zinc oxide fabricated via electrodeposition and etching is also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Atomic Force Microscopy and Infrared Nanospectroscopy of COVID-19 Spike Protein for the Quantification of Adhesion to Common Surfaces

The COVID-19 pandemic has claimed millions of lives worldwide, sickened many more, and has resulted in severe socio-economic consequences. As society returns to normal, understanding the spread and persistence of SARS CoV-2 on commonplace surfaces can help to mitigate future outbreaks of coronaviruses and other pathogens. We hypothesize that such an understanding can be aided from studying the binding and interaction of viral proteins with non-biological surfaces. Here, we propose a methodology for investigating the adhesion of the SARS CoV-2 spike glycoprotein on common inorganic surfaces such as aluminum-, copper-, iron-, silica-, and ceria-oxides as well as metallic gold. Quantitative adhesion was obtained from the analysis of measured forces at the nanoscale using an atomic force microscope operated under ambient conditions. Without imposing further constraints on the measurement conditions, our preliminary findings suggest that spike glycoproteins interact with similar adhesion forces across the majority of the metal oxides tested with the exception to gold, for which attraction forces ~10 times stronger than all other materials studied were observed. Ferritin, which was used as a reference protein, was found to exhibit similar adhesion forces as SARS CoV-2 spike protein. Further, this study results show that glycoprotein adhesion forces for similar ambient humidity, tip shape, and contact surface are non-specific to the properties of metal oxide surfaces, which are expected to be covered by a thin water film. The findings suggest that at ambient conditions glycoprotein adhesion to metal oxides is primarily controlled by the water capillary forces and they depend on the surface tension of the liquid (water). We discuss further strategies warranted to decipher the intricate nanoscale forces for improved quantification of the adhesion.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Stretching and Bending Moduli of Bilayer Films Inferred from Wrinkle Patterns

Wrinkling patterns were used to investigate the mechanical properties of thin poly­(styrene) (PS)/poly­(methyl methacrylate) (PMMA) and PS/gold (Au) bilayer films. Films were floated on water with a water drop on the surface to induce wrinkling. The thicknesses and thickness ratios of the films were varied over a broad range. The PS/PMMA bilayer was chosen to provide a contrast in wetting properties, with equilibrium contact angles of θPMMA = 68° and θPS = 88° with water. The PS/Au bilayer was chosen to provide a large contrast in Young’s moduli, E Au = 72 GPa and E PS = 3.4 GPa. The stretching (Y) and bending (B) moduli of the bilayer films were obtained from measurements of the length and number of wrinkles in the wrinkle patterns. The experimentally derived values of Y and B were in reasonable agreement with the values computed from the bulk Young’s moduli and the thicknesses of the two components in the bilayer. The values of Y and B did not depend on which face of the film was exposed to the water droplet or bath when the capillary stresses were considered. Thus, finite size effects from the film thicknesses were unimportant over the range of thicknesses studied, and no relative displacement of the films was found, with the films remaining well-bonded even with deformation associated with wrinkling.

Chang, Jooyoung↗
DOE OSTI2022

Molecular Alignment of a Meta-Aramid on Carbon Nanotubes by In Situ Interfacial Polymerization

Molecularly organized nanocomposites of polymers and carbon nanotubes (CNTs) have great promise as high-performance materials; in particular, conformal deposition of polymers can control interfacial properties for mechanical load transfer, electrical or thermal transport, or electro/chemical transduction. However, controllability of polymer-CNT interaction remains a challenge with common processing methods that combine CNTs and polymers in melt or in solution, often leading to nonuniform polymer distribution and CNT aggregation. In this work, we demonstrate CNTs within net-shape sheets can be controllably coated with a conformal coating of meta-aramid by simultaneous capillary infiltration and interfacial polymerization. We determine that π-interaction between the polymer and CNTs results in chain alignment parallel to the CNT outer wall. Subsequent nucleation and growth of the precipitated aramid forms a smooth continuous layered sheath around the CNTs. These findings motivate future investigation of mechanical properties of the resulting composites, and adaptation of the in situ polymerization method to other substrates.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Two-Dimensional Mechanics of Atomically Thin Solids on Water

Movement of a three-dimensional solid at an air–water interface is strongly influenced by the extrinsic interactions between the solid and the water. The finite thickness and volume of a moving solid causes capillary interactions and water-induced drag. In this Letter, we report the fabrication and dynamical imaging of freely floating MoS 2 solids on water, which minimizes such extrinsic effects. For this, we delaminate a synthesized wafer-scale monolayer MoS 2 onto a water surface, which shows negligible height difference across water and MoS 2 . Subsequently patterning by a laser generates arbitrarily shaped MoS 2 with negligible in-plane strain. We introduce photoswitchable surfactants to exert a lateral force to floating MoS 2 with a spatiotemporal control. Using this platform, we demonstrate a variety of two-dimensional mechanical systems that show reversible shape changes. Our experiment provides a versatile approach for designing and controlling a large array of atomically thin solids on water for intrinsically two-dimensional dynamics and mechanics.

2D materials↗
DOE OSTI2025

The Impact of Europium as a Fission Product Surrogate on Chromium Corrosion in Molten Chloride Salt

The rising interest in molten salts, both as thermal energy storage media and as high-temperature solvents for fissile materials in advanced nuclear reactors, has spurred significant growth in research on structural and functional salt-facing materials. Impurities, such as water, play a significant role in the degradation of materials in molten salt environments. Other impurities, such as fission products, are expected to accumulate in molten salts during normal reactor operation and can affect the properties of the salt and salt-facing materials. During normal reactor operation, rare-earth element species are expected to form as byproducts of fission reactions, potentially degrading or altering the performance of both structural and functional materials exposed to salts. Here, in this work, fission product surrogates, europium metal and EuCl 3 , were added to the KCl-MgCl 2 salt while exposing pure Cr specimens in the melt at 600 and 700 °C for 1000 h. Low reactivity was observed with the baseline salt, while both the Eu and EuCl 3 additions to the salt resulted in increased mass loss of Cr specimens. A capillary electrophoresis technique was developed to enable the detection of low parts-per-million (ppm) concentrations of europium (Eu) in chloride salt both before and after exposure of Cr metal. This technique provides a sensitive and reliable method for monitoring trace levels of Eu, which is critical for understanding the interactions and potential contamination effects in salt-facing materials during reactor operation. This quantification technique can be applied to other cationic and anionic contaminants in halide salts.

chloride salt↗
DOE OSTI2024

Direct Visualization of Laser-Induced Coalescence and Alloying of Au into Ag Nanowires

Noble metal nanocomposites with controlled morphology and composition have been largely useful in a wide variety of applications like catalysis, plasmonics, and biological applications. Herein, we show pulsed-laser-assisted fabrication of beaded Au-Ag nanowires with a variety of morphologies and compositions via coalescence and alloying of Au nanoparticles (NP) into a Ag nanowire (NW). Direct visualization of the evolution process with in situ laser heating transmission electron microscopy (ILH-TEM) leads to unambiguous insights into the mechanism of formation for the first time. Ag, being a soft material, melts at the surface to bridge the gap between the NP-NW, forming a cup-like morphology underneath the Au NP via capillary action. Progressive laser irradiation leads to wetting of the Au NP with Ag, forming an envelope around the NP. This is associated with the formation of a valley in Ag NW around the NP, which flattens gradually by partial embedding of the NP. Interdiffusion of Au into Ag and vice versa sets in at this stage, leading to the depletion of Au from the Au-rich NP region. Prolonged irradiation leads to gradual intermixing of Au-Ag forming beaded Au-doped Ag nanowires with homogeneous composition. Such a step-by-step understanding of the coalescence and alloying process has implications in nanowelding, which holds the future in designing efficient transparent conductors and printed electronics.

Isik, Tugba↗
DOE OSTI2025

Manufacturing of Continuous Microporous Polymeric Fibers for Separation Applications

Polyolefin plastic waste, particularly polypropylene, is one of the most prevalent components in the plastic waste stream generated globally. However, only a small fraction of this waste is recycled and reintegrated into second applications. These materials have significant embedded energy that could be used for additional productivity if recycled properly. Therefore, there is a critical need to develop scalable processing techniques with high throughput to effectively recycle it. We report the continuous manufacturing of microporous fibers using waste polypropylene plastic and melt-processable lignin, a plant biomass constituent produced as a byproduct in paper mills or biorefineries, as a template to create pores. Further, these filaments with hierarchical porosity─created by controlled microphase separation during high-speed extensional flow followed by removal of lignin─exhibit exceptional capillary action for hydrophobic liquids. The resulting porous fibers can be used for various separation applications. For example, the oil uptake of the fibers is 9.59 ± 0.82 g/g for applications in oil recovery in bodies of water. In addition, polyethylenimine infiltration within these nanoporous fibers introduces cyclic room temperature sorption and thermal desorption potential of acidic gases such as CO 2 in a bench-scale experiment. The fibers exhibit multiple cycles of CO 2 absorption, with a range of 0.15 to 0.17 mmol/g. Thus, these polyethylenimine-infiltered nanoporous polypropylene fibers can also be used in removing acidic gases from a gas mixture.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Kinetic Model for the Reduction of Cu II Sites by NO + NH 3 and Reoxidation of NH 3 -Solvated Cu I Sites by O 2 and NO in Cu-SSZ-13

In this work, a kinetic model is developed for the reduction of Cu II sites by NO + NH 3 and the reoxidation of NH 3 -solvated Cu I sites by O 2 and NO in Cu-SSZ-13. Fourier transform infrared (FTIR) spectroscopy and spatially resolved capillary inlet mass spectrometry (SpaciMS) measurements during transient reactor experiments are utilized to identify the rate parameters associated with NO + NH 3 RHC (reduction half-cycle), proposed to occur via two distinct pathways involving adsorbed NH 3 and gas-phase NH 3 . The resulting NO + NH 3 RHC model is validated using spatiotemporal N 2 measurements covering a wide range of temperatures (200–450 °C) and space velocities (53,000–640,000 h –1 ). N 2 O formation is observed and modeled during NO + NH 3 RHC, with quantitative validation under standard selective catalytic reduction (SCR) conditions. Experimentally measured enthalpic and entropic changes associated with O 2 adsorption on NH 3 -solvated Cu I (ZCu(NH 3 ) 2 ) complexes [ Kamasamudram, K. Catal. Today 2010 , 151 (3–4), 212-222], along with activation energies estimated computationally for the intercage diffusion of ZCu(NH 3 ) 2 complexes [ Paolucci, C. Science 2017 , 357 (6 354), 898-903], are incorporated into a mean field kinetic model for the low-temperature oxidation half-cycle (OHC). Significant NH 3 release is observed during the isothermal oxidation of Cu I sites, attributed to desorption of NH 3 ligands from NH 3 -solvated Cu II dimers (Z 2 Cu 2 (NH 3 ) 4 O 2 ). Reduction of these dimeric complexes leads to the consumption of one NO/Cu II , contradicting the expected reduction stoichiometry. Inclusion of a global Arrhenius rate for the NO titration of Z 2 Cu 2 (NH 3 ) 4 O 2 complexes provides accurate representations of standard SCR on reduced and oxidized catalysts, predicting transient NO and NH 3 consumption between 150 and 250 °C as a function of hydrothermal aging. Deactivation of low-temperature standard SCR by NH 3 is observed at high NH 3 pressures, modeled via the formation of superoxo amino (ZCu(NH 3 ) 3 OO*) complexes during NH 3 titration of Z 2 Cu 2 (NH 3 ) 4 O 2 complexes [ Negri, C. J. Am. Chem. Soc. 2020 , 142 (37), 15884-15896]. The redox kinetic model presented here provides a foundational description of active site redox during low-temperature standard SCR, combining the recent kinetic, spectroscopic, and computational findings on the mechanism of standard SCR over Cu-SSZ-13.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Species, Pathways, and Timescales for NH 3 Formation by Low-Temperature Atmospheric Pressure Plasma Catalysis

Species, pathways, and timescales for NH3 production by plasma catalysis over transition-metal wools are determined by measuring plasma-derived species densities [N, H, and N 2 (v)], quantitatively correlating consumption of these species with NH 3 formation, and measuring consumption of plasma-derived species at different residence times. These findings are enabled by a capillary flow through Ar/N 2 /H 2 plasma jet reactor setup that allows for the measurement of gas-phase species densities by molecular beam mass spectrometry. Surface-mediated reactions involving N radicals are responsible for NH 3 formation over Fe, Ni, and Ag surfaces. N reacts to form NH 3 with ~100% selectivity over Ni and Ag when H/N > 3 and % H 2 ≥ 0.5. The selectivity to ammonia drops as H and H 2 densities decrease for each catalyst. A comparison between amounts of NH 3 formed and N consumed with and without catalysts present shows that surface reactions enable higher and more selective conversion of N to NH 3 than gas-phase reactions alone. The conversion of N to NH 3 is negligible in the absence of H, demonstrating that H is required to produce NH 3 at these operating conditions. The consumption of N occurs on the same timescale as NH 3 formation, further confirming that reactions involving N contribute to NH 3 formation. Though vibrationally excited N 2 [N 2 (v)] is produced in quantities exceeding N by 100-fold, consumption of N 2 (v) on the catalytic surface does not contribute to NH 3 formation. Furthermore, these findings show that for low-temperature atmospheric pressure plasma catalysis, surface- mediated reactions among radical N and H species drive NH 3 formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Chemical Imaging of Atmospheric Biomass Burning Particles from North American Wildfires

The effects of biomass burning aerosols (BBA) on radiative forcing and cloud formation depend on chemical composition and the internal structures of individual particles within smoke plumes. To improve our understanding of the chemical and physical properties of BBA emitted at different times of the day and their evolution during atmospheric aging, we conducted a study as a part of the Fire Influence on Regional to Global Environments and Air Quality field campaign. Particle samples were collected onboard a research aircraft from smoke plumes from a wildfire in eastern Oregon during late afternoon and nighttime flights on August 28, 2019. A time-resolved aerosol collector was used to collect samples on substrates for offline spectromicroscopic imaging to investigate the single-particle characteristics of BBA particles. Approximately 20,400 individual particles from 10 selected samples were analyzed using computer-controlled scanning electron microscopy coupled with energy-dispersive X-ray microanalysis, revealing their elemental composition, morphology, and viscosity. Elemental microanalysis indicated that aged potassium is likely found in the form of K 2 SO 4 , KNO 3 , and possible K-organic salts. Further chemical speciation and carbon bonding mapping within individual particles were conducted using synchrotron-based scanning transmission X-ray microscopy (STXM) coupled with near edge X-ray absorption fine structure (NEXAFS) spectroscopy. Real-time, water-soluble light absorption measurements were acquired using a particle-into-liquid sampler instrument coupled to a liquid waveguide capillary cell and total organic analyzer. In the late afternoon samples, 65% of the total particle number population consisted entirely of organic components, compared to 46% in the nighttime particles. These differences were attributed to discrepancies in composition at the time of emission and to the daytime condensation and accumulation of photochemically formed secondary organic material on existing BBA particles, a process that halts at night. Microscopy images indicated that particle viscosity was lower in the nighttime particles (<10 1 Pa·s), likely due to increased relative humidity and a higher contribution from hygroscopic inorganic components. The chemical heterogeneity of individual particles was quantified using STXM-derived mixing state parameters. The nature of carbon bonding within individual particles was inferred from the extent of carbon sp 2 hybridization derived from NEXAFS spectra. Average percentages of sp 2 hybridization range between 40% and 60%, with no noticeable differences between late afternoon and nighttime flights. These findings were compared with the online optical properties of both late afternoon and nighttime smoke plumes, providing valuable insights into the complex relationship between chemical composition and optical properties of BBA particles at different times of the day.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Residual Strain and Nanostructural Effects during Drying of Nanocellulose/Clay Nanosheet Hybrids: Synchrotron X-ray Scattering Results

Cellulose nanofibrils (CNF) with 2D silicate nanoplatelet reinforcement readily form multifunctional composites by vacuum-assisted self-assembly from hydrocolloidal mixtures. The final nanostructure is formed during drying. The crystalline nature of CNF and montmorillonite (MTM) made it possible to use synchrotron X-ray scattering (WAXS, SAXS) to monitor structural development during drying from water and from ethanol. Nanostructural changes in the CNF and MTM crystals were investigated. Changes in the out-of-plane orientation of CNF and MTM were determined. Residual drying strains previously predicted from theory were confirmed in both cellulose and MTM platelets due to capillary forces. The formation of tactoid platelet stacks could be followed. We propose that after filtration, the constituent nanoparticles in the swollen, solid gel already have a “fixed” location, although self-assembly and ordering processes take place during drying.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hierarchical Biogenic-Based Thermal Insulation Foam

Biogenic-based foam, renowned for its sustainable and eco-friendly properties, is emerging as a promising thermal insulating material with the potential to significantly enhance energy efficiency and sustainability in building applications. However, its relatively high thermal conductivity, large-pore configurations, and energy-intensive manufacturing processes hinder its widespread use. Here, we report on the scalable, one-pot synthesis of biogenic foams achieved by integrating recycled paper pulp and in situ nanoporous silica formation, resulting in a hierarchical structure comprising both micropores and nanopores. Ambient solvent-exchange drying can preserve the pore structure by reducing the capillary forces during the drying process. The resulting flame-retardant and hydrophobic foam exhibits low density (0.110 g/cm 3 ), ideal porosity (70.69%), excellent thermal conductivity (0.033 W/(m·K)), and impressive compressive strength (1.48 MPa at 80% strain). Furthermore, this recyclable biogenic foam, with its hierarchical pore structure and environmental durability, shows great potential for energy-efficient building applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Biomimetic Rebuilding of Multifunctional Red Blood Cells: Modular Design Using Functional Components

The design and synthesis of artificial materials that mimic the structures, mechanical properties, and ultimately functionalities of biological cells remains a current holy grail of materials science. Here based on a silica cell bio-replication approach, we report the design and construction of synthetic rebuilt red blood cells (RRBCs) that fully mimic the broad properties of native RBCs: size, biconcave shape, deformability, oxygen carrying capacity, long circulation time. Four successive nano-scale processing steps: RBC bioreplication, layer-by-layer polymer deposition, and precision silica etching, followed by RBC ghost membrane vesicles fusion are employed for RRBC construction. A panel of physicochemical analyses including zeta potential measurement, fluorescence microscopy, and antibody-mediated agglutination assay proved the recapitulation of RBC shape, size, and membrane structure. Flow-based deformation studies carried out in a microfluidic blood capillary model confirrned the ability of RRBCs to deform and pass through small slits and reconstitute themselves in a manner comparable to native RBCs. Circulation studies of RRBCs conducted ex-ovo in a chick embryo and in vivo in a mouse model demonstrated the requirement of both deformability and native cell membrane surface to achieve long-term circulation. To confer additional non-native functionalities to RRBCs, we developed modular procedures in which to load functional cargos such as hemoglobin, drugs, magnetic nanoparticles, and ATP biosensors within the RRBC interior to enable various functions, including oxygen delivery, therapeutic drug delivery, magnetic manipulation, and toxin biosensing and detection. Taken together, RRBCs represent a class of long circulating RBC-inspired artificial hybrid materials with a broad range of potential applications.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Towards Understanding of Cracking during Drying of Thick Aqueous-Processed LiNi 0.8 Mn 0.1 Co 0.1 O 2 Cathodes

Replacing N-methyl-2-pyrrolidone (NMP) with water for processing of lithium-ion battery (LIB) electrodes has both cost and environmental benefits, which include reduced drying time, lower dryer capital cost, elimination of NMP recovery capital equipment, and no release of volatile organic compounds (VOCs) into the environment. However, aqueous-processed thick cathodes (≳4 mAh/cm 2 ) typically exhibit detrimental cracking during drying that is not observed for the NMP-based counterpart. The reasons for cracking of these water-based thick electrodes are still not well understood due to the complex nature of the colloidal dispersions used in the LIB electrode processing steps. In this work, the contributions of various factors responsible for cracking are discussed. We show that eliminating hydrogen evolution due to corrosion of the aluminum current collector eliminated the majority of the cracks regardless of the coating thickness, identifying the gas evolution as the primary reason for electrode cracking. Some secondary cracks and pinhole-type defects remained after addressing the aluminum current collector corrosion, which are thought to be caused by an inferior binding network formed by carbon black and binder in aqueous-processed cathodes compared to those processed with NMP. The thick aqueous processed cathodes are not able to sufficiently withstand the drying stresses without crack formation. We demonstrate reduction of these secondary defects by either improving the binding network or by reducing the drying stress. The former was achieved by replacing carbon black with vapor grown graphite tubes (VGGTs) that caused a more efficient utilization of the emulsion binder. Here, the latter was achieved by adding a small amount of IPA as a co-solvent that has been shown to reduce capillary stresses.

25 ENERGY STORAGE↗
DOE OSTI2023

A Nanocavitation Approach to Understanding Water Capture, Water Release, and Framework Physical Stability in Hierarchically Porous MOFs

Chemically stable metal–organic frameworks (MOFs) featuring interconnected hierarchical pores have proven to be promising for a remarkable variety of applications. Nevertheless, the framework’s susceptibility to capillary-force-induced pore collapse, especially during water evacuation, has often limited practical applications. Methodologies capable of predicting the relative magnitudes of these forces as functions of the pore size, chemical composition of the pore walls, and fluid loading would be valuable for resolution of the pore collapse problem. Here, we report that a molecular simulation approach centered on evacuation-induced nanocavitation within fluids occupying MOF pores can yield the desired physical-force information. Here, the computations can spatially pinpoint evacuation elements responsible for collapse and the chemical basis for mitigation of the collapse of modified pores. Experimental isotherms and difference-electron density measurements of the MOF NU-1000 and four chemical variants validate the computational approach and corroborate predictions regarding relative stability, anomalous sequence of pore-filling, and chemical basis for mitigation of destructive forces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗