Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Post-test Inspection of NASA’s Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge and Neutralizer Cathodes

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 h of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for both discharge and neutralizer cathodes. Discharge keeper erosion was found to be significantly reduced from what was observed in the NEXT 2 kh wear test and NSTAR Extended Life Test, providing adequate protection of vital cathode components throughout the test with ample lifetime remaining. The area of the discharge cathode orifice plate that was exposed by the keeper orifice exhibited net erosion, leading to cathode plate material building up in the cathode-keeper gap and causing a thermally-induced electrical short observed during the test. Significant erosion of the neutralizer cathode orifice was also found and is believed to be the root cause of an observed loss in flow margin. Deposition within the neutralizer keeper orifice as well as on the downstream surface was thicker than expected, potentially resulting in a facility-induced impact on the measured flow margin from plume mode. Neutralizer keeper wall erosion on the beam side was found to be significantly lower compared to the NEXT 2 kh wear test, likely due to the reduction in beam extraction diameter of the ion optics that resulted in decreased ion impingement. Results from the post-test inspection have led to some minor thruster design improvements.

Ion engine↗
DOE OSTI2026

Three-beam hybrid fs/ps coherent anti-Stokes Raman scattering of rotation–vibration non-equilibrium

In this work, we demonstrate time-resolved rotational and vibrational temperature measurements to probe plasma non-equilibrium through a simple three-beam hybrid femtosecond/picosecond coherent anti-Stokes Raman scattering (fs/ps CARS) system. A single pump/Stokes pair is employed to generate both the pure-rotational and ro-vibrational Raman coherence. A novel phase-matching scheme, to our knowledge, is employed to spatially overlap the two CARS signals, simplifying the optical design and allowing signal selection by tuning a single spectrometer grating. Measurements were performed near the electrodes in a N 2 DC glow discharge. Both the rotational temperature and the vibrational populations up to $v$ = 8 were calculated from the separately measured single-shot pure-rotational and ro-vibrational CARS spectra. Strong rotation–vibration non-equilibrium was observed at both electrodes, with the cathode showing higher vibrational and rotational temperatures. In addition, non-Boltzmann behaviors were observed at both electrodes. This simplified approach enables measurements of rotational and vibrational temperatures with high spatial resolution in non-equilibrium flows.

42 ENGINEERING↗
DOE OSTI2025

Control of Two Solid Electrolyte Interphases at the Negative Electrode of an Anode‐Free All Solid‐State Battery based on Argyrodite Electrolyte

Abstract Anode‐free all solid‐state batteries (AF‐ASSBs) employ “empty” current collector with three active interfaces that determine electrochemical stability; lithium metal – Solid electrolyte (SE) interphase (SEI‐1), lithium – current collector interface, and collector – SE interphase (SEI‐2). Argyrodite Li 6 PS 5 Cl (LPSCl) solid electrolyte (SE) displays SEI‐2 containing copper sulfides, formed even at open circuit. Bilayer of 140 nm magnesium/30 nm tungsten (Mg/W‐Cu) controls the three interfaces and allows for state‐of‐the‐art electrochemical performance in half‐cells and fullcells. AF‐ASSB with NMC811 cathode achieves 150 cycles with Coulombic efficiency (CE) above 99.8%. With high mass‐loading cathode (8.6 mAh cm −2 ), AF‐ASSB retains 86.5% capacity after 45 cycles at 0.2C. During electrodeposition of Li, gradient Li‐Mg solid solution is formed, which reverses upon electrodissolution. This promotes conformal wetting/dewetting by Li and stabilizes SEI‐1 by lowering thermodynamic driving force for SE reduction. Inert refractory W underlayer is required to prevent ongoing formation of SEI‐2 that also drives electrochemical degradation. Inert Mo and Nb layers likewise protect Cu from corroding, while Li‐alloying layers (Mg, Sn) are less effective due to ongoing volume changes and associated pulverization. Mechanistic explanation for observed Li segregation within alloying Li x Mg layer is provided through mesoscale modelling, considering opposing roles of diffusivity differences and interfacial stresses.

Wang, Yixian [Materials Science and Engineering Pr↗
DOE OSTI2025

Anion Vacancies Coupling with Heterostructures Enable Advanced Aerogel Cathode for Ultrafast Aqueous Zinc‐Ion Storage

As a potential cathode material, manganese-based sulfide has recently attracted increasing interest due to its many advantages in aqueous zinc-ion storage. Unfortunately, some challenges such as sluggish kinetics, unstable structure, and controversial phase transition mechanism during the energy storage process hinder its practical application. Herein, inspired by density functional theory (DFT) calculations, a novel 3D sulfur vacancy-rich and heterostructured MnS/MXene aerogel is designed, and used as a cathode for aqueous Zn-ion batteries/hybrid capacitors (ZIBs/ZICs) for the first time. Thanks to the synergistic modification strategy of sulfur vacancies and heterostructures, the as-constructed MnS/MXene//Zn ZIBs exhibit significantly enhanced electrochemical properties, especially outstanding rate capability and cyclic stability. More encouragingly, the as-assembled MnS/MXene//porous carbon (PC) ZICs exhibit an ultrahigh energy density, a high power density, and a splendid cycling lifespan. Most notably, systematic kinetic analyses, ex situ characterizations, and DFT calculations illustrate that MnS/MXene first irreversibly converts into MnO x @ZnMnO 3 /MXene, and then undergoes a reversible conversion from MnO x @ZnMnO 3 /MXene to MnOOH@ZnMn 2 O 4 /MXene, accompanied by the co-insertion/extraction of H + and Zn 2+ . Further, the synergistic modification strategy of sulfur vacancies and heterostructures and the thorough mechanistic study proposed in this work offer valuable guidance for designing and exploiting high-performance cathodes in aqueous zinc-based energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2026

Stabilizing Cathode–Electrolyte Interphase of Nickel-Rich Single-Crystal Cathodes for Lithium-Ion Batteries

Nickel-rich single-crystal (SC) layered oxides are promising cathode candidates for next-generation lithium-ion batteries (LIBs) owing to their high energy density and structural robustness against intergranular cracking. However, their intrinsic surface reactivity with liquid electrolytes accelerates parasitic reactions at the cathode–electrolyte interphase (CEI), leading to transition-metal dissolution, gas generation, and impedance buildup. In this work, we synthesized SC-Li x Ni 0.9 Mn 0.05 Co 0.05 O 2 (NMC9055, 1 ≤ x ≤ 1.2) using a eutectic-assisted method and investigated interface stabilization strategies. A nickel-deficient Li x Ni 0.6 Mn 0.2 Co 0.2 O 2 (NMC622, 1 ≤ x ≤ 1.2) coating was applied via evaporation-based deposition to suppress CEI degradation pathways. Structural and compositional analyses confirmed uniform shell formation and preserved particle integrity. Half-cell electrochemical testing against lithium metal revealed ∼10% higher capacity retention and improved reversibility compared with pristine SC NMC9055, particularly under high-voltage operation. In conclusion, these results highlight the critical role of controlled surface chemistry in mitigating CEI instability in nickel-rich SC cathodes, offering a pathway toward enabling durable high-energy LIBs.

Coating processes↗
DOE OSTI2024

Local ionic transport enables selective PGM-free bipolar membrane electrode assembly

Bipolar membranes in electrochemical CO 2 conversion cells enable different reaction environments in the CO 2 -reduction and O 2 -evolution compartments. Under ideal conditions, water-splitting in the bipolar membrane allows for platinum-group-metal-free anode materials and high CO 2 utilizations. In practice, however, even minor unwanted ion crossover limits stability to short time periods. Here we report the vital role of managing ionic species to improve CO 2 conversion efficiency while preventing acidification of the anodic compartment. Through transport modelling, we identify that an anion-exchange ionomer in the catalyst layer improves local bicarbonate availability and increasing the proton transference number in the bipolar membranes increases CO 2 regeneration and limits K + concentration in the cathode region. Through experiments, we show that a uniform local distribution of bicarbonate ions increases the accessibility of reverted CO 2 to the catalyst surface, improving Faradaic efficiency and limiting current densities by twofold. Using these insights, we demonstrate a fully platinum-group-metal-free bipolar membrane electrode assembly CO 2 conversion system exhibiting <1% CO 2 /cation crossover rates and 80-90% CO 2 -to-CO utilization efficiency over 150 h operation at 100 mA cm -2 without anolyte replenishment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Mechanistic insights into CO 2 capture and electrochemical conversion in nonaqueous Na–CO 2 batteries

Developing efficient energy storage systems that capture and convert CO 2 is critical for mitigating carbon emissions. Here, we report a Na–CO 2 battery with ruthenium dioxide (RuO 2 ) cathode catalysts and propane-1,3-diamine (PDA) as an electrolyte additive to enhance CO 2 capture and conversion efficiency. The integration of CO 2 adsorption and electrochemical reduction facilitates activation of the inert CO 2 molecule and circumvents gas–solid–liquid ternary-phase reactions at the interface. We employed density functional theory (DFT) calculations to systematically unravel the reaction mechanisms and energetics governing CO 2 reduction, both with and without PDA. Our results reveal an energetically favorable pathway toward the formation of Na 2 CO 3 and C as final discharge products, rather than sodium oxalate (Na 2 C 2 O 4 ). The CO 2 –amine adduct facilitates charge transfer from PDA to CO 2 , which results in activation of CO 2 . The kinetics of CO 2 conversion and regeneration of PDA were found to be significantly enhanced on the RuO 2 surface compared to the bulk electrolyte. More importantly, pre-activation of CO 2 via the amine–CO 2 adduct lowers the total overpotential to 2.44 V, compared to 3.13 V without PDA. This study provides fundamental insights into CO 2 electroreduction in Na–CO 2 batteries and underscores the promise of electrolyte engineering for sustainable CO 2 utilization and high-performance energy storage.

25 ENERGY STORAGE↗
DOE OSTI2025

Crossover Effects of Transition‐Metal Ions on Lithium‐Metal Anode in Localized High Concentration Electrolytes

Abstract The stability of the solid–electrolyte interphase (SEI) is critical to the cycle life of lithium‐metal batteries (LMBs). While the crossover effect of transition‐metal ions from cathode to anode is extensively studied in lithium‐ion batteries with graphite anodes, its impact on LMBs remains largely unexplored. Herein, this study investigates the electrochemical and chemical properties of SEI layers formed on lithium‐metal anodes in localized high‐concentration electrolytes (LHCEs) containing dissolved transition‐metal ions (Ni 2+ , Mn 2+ , and Co 2+ ). It is demonstrated that transition‐metal ions in LHCEs reduce the coulombic efficiency (CE) and significantly degrade the cycle life of LMBs. Time‐of‐flight secondary‐ion mass spectrometry (ToF‐SIMS) reveals that SEI structures differ depending on the dissolved TM ion, with Mn 2+ and Co 2+ inducing severe destabilization, and Ni 2+ exhibiting a less severe impact. These findings underscore the detrimental effects of transition‐metal crossover effects in LMB systems.

Guo, Zezhou [Materials Science and Engineering Pro↗
DOE OSTI2025

Novel Electrowinning Reactor for the Energy-Efficient, Low- Cost Production of Rare Earth Metals

This project developed a novel neodymium (Nd) electrowinning reactor for energy-efficient electrowinning of Nd metal. Throughout this project we have developed an alternative chloride based molten salt electrolysis process. Our process lowers the specific electrical energy consumption compared to the state of the art, while producing reusable chlorine gas and eliminating direct CO2 and PFC emissions. Facilities required for implementing the project were setup and designs were finalized, and a standard operating procedure for safe operation of high temperature electrolysis cells was written. The electrowinning reactor was designed and constructed. Electrolysis experiments confirmed the ability to reproducibly electrowin Nd metal on a Mo cathode. The current efficiency for Nd electrowinning was measured as a function of applied current density in the presence of the separator. Successful electrowinning of Nd sponge at high current densities (200 mA/cm2 and above) at a current efficiency >80% was demonstrated using multiple techniques. Stable Nd electrowinning up to 10h at 250 mA/cm2 was demonstrated. All of these design advancements were used to develop a techno-economic and life cycle assessment model that demonstrated that our process could be operated at cost of less than $0.20/kg-Nd (~30% lower compared to state of the art when comparing electrolysis energy cost) with a >20% total reduction in global warming potential compared to the state of the art while generating no direct CO2 or perfluorocarbon emissions.

42 ENGINEERING↗
DOE OSTI2024

Electro-Chemo-Mechanical Evolution at the Garnet Solid Electrolyte–Cathode Interface

Solid-state batteries promise higher energy density and improved safety compared with lithium-ion batteries. However, electro-chemomechanical instabilities at the solid electrolyte interface with the cathode and the anode hinder their large scale implementation. Here, in this study, we focus on resolving electro-chemo-mechanical instability mechanisms and their onset conditions between a state-of-the-art cathode, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and the garnet Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte. We used thin-film NMC622 on LLZO pellets to place the interfacial region within the detection depth of the X-ray characterization techniques. The experimental probes of the near-interface region included in operando X-ray absorption spectroscopy and ex situ focused ion beam scanning electron microscopy. Electrochemical degradation was not observable during cycling at room temperature with 4.3 V versus Li/Li + charge voltage cutoff, or with stepwise potentiostatic hold up to 4.1 V versus Li/Li + . In contrast, secondary phases including reduced transition metal species (Ni 2+ , Co 2+ ) were found after cycling up to 4.3 V versus Li/Li + at 80 °C and during potentiostatic hold at 4.3 V versus Li/Li + (Ni 2+ ). Intergranular cracks between NMC622 grains and delamination at the NMC622|LLZO interface occurred readily after the first charge. These interface reaction products and mechanical failure lowered the capacity and cell efficiency due to partial loss of the NMC622 phase, partial loss of contact at the interface, and a higher polarization resistance. Electrochemical instability between delithiated NMC622 and LLZO could be mitigated by using a low charge voltage cutoff or cycling at lower temperature. Ways to engineer the mechanical properties to avoid crack deflection and delamination at the interface are also discussed for enhancing mechanical stability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Characterization of Cs 3 Sb photocathodes at cryogenic temperatures

Here, we report measurements of quantum efficiency (QE) and mean transverse energy (MTE) from Cs 3 Sb photocathodes in a wide range of photon energies at both room and cryogenic temperatures. Our measurements show a strong temperature dependence of MTE even at photon energies well above threshold, indicating the presence of strong inelastic scattering of excited electrons during transport before emission into vacuum. We also demonstrate a cathode cooling method that largely preserves the QE while reducing MTE, allowing us to achieve MTEs as low as 58 meV with 3% QE in green light from Cs 3 Sb photocathodes. Our results are crucial for producing brighter electron beams for various photoinjector applications like ultrafast electron diffraction and microscopy, x-ray free-electron lasers, and particle colliders.

36 MATERIALS SCIENCE↗
DOE OSTI2026

All-organic self-separating three-dimensionally nanoarchitected electrochemical energy storage devices

This work realizes a three-dimensionally (3D) nanoarchitected, all organic, "self-separating" lithium-ion electrochemical energy storage (EES) device that is cycled as a solid-state full cell. The device is enabled by a monolithic carbon anode with a co-continuous pore network, derived from the structure direction of resols by an ultra-large molar mass block copolymer (BCP), poly(styrene-block-2-dimethylaminoethyl methacrylate) (SA). Electropolymerization of a single-phase conductive and redox-active material, poly((2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl)methyl 9,10-dioxo-9,10-dihydroanthracene-2-carboxylate) (PAQEDOT), into the pore space provides the cathode of the cell. The device is electronically contacted to the relevant electrode network enabled by the co-continuous nature of each electrode. Electrochemical processing via cycling against external lithium in an electrolyte generates a solid electrolyte interphase (SEI) as a separator and lithiates the cell electrodes, after which the EES device is cycled in the solid state. While the full cell does not demonstrate high cyclability, the best full cell demonstrates a discharge capacity of 267 milliamp hours per gram (mAh/g). This work marks, to the best of knowledge of the authors, the first example of an all-organic materials derived 3D nanoarchitected EES device, as well as the first design of "self-separating" cell fabrication. Furthermore, generalization of the design to another co-continuous carbon form factor is demonstrated.

FOS: Physical sciences↗
DOE OSTI2026

Translating Fundamental Insights into Ag-Based Bimetallic Electrocatalysts to Anion-Exchange Membrane Fuel Cells

To address challenges of high costs and scalability for fuel cells, it is essential to develop af-fordable and earth-abundant materials that are Pt-group-metal (PGM)-free. Recent advance-ments in PGM-free electrocatalysis for the oxygen reduction reaction (ORR) in alkaline media show that high catalyst loadings are needed to achieve high reaction rates; however, there are associated mass transport limitations. To address this issue, we develop low-loading ionomer-less Ag-bimetallic thin films by alloying with 3d block elements or Sn. We bridge knowledge from fundamental rotating disk electrode (RDE) studies to gas-diffusion cathodes in high-temperature anion-exchange membrane fuel cells (HT-AEMFCs), resulting in high-activity ORR catalysis and peak power densities up to 1.2 W cm-² geo for the Ag-Sn and Ag-Co alloys. Here, experimental post-characterization and theoretical calculations reveal small Co or Sn oxide nano-islands on Ag as likely active sites enhancing ORR activity, ultimately offering these low-loading PGM-free ORR materials as a viable path towards sustainable energy conversion.

Catalysts↗
DOE OSTI2026

A scalable, biopolymer-based microenvironment for electrochemical CO 2 conversion to multicarbon products with current densities over 2 A cm −2

The electrochemical CO 2 reduction reaction (CO 2 RR) relies heavily on the surrounding microenvironment to promote formation of desirable multicarbon (C 2+ ) products. However, microenvironment control to achieve high C 2+ yields at industrially relevant current densities remains a crucial challenge. We report that chitosan, cellulose and chitin biopolymer coatings on CO 2 RR electrocatalysts enhance the microenvironment by increasing local CO 2 /CO concentration, reducing local water activity and providing suitable ion conductivity and local pH. This facile approach achieves C 2+ Faradaic efficiencies of 90 ± 1.7% at 1.6 A cm −2 and C 2+ Faradaic efficiency = 83 ± 3.2% at 2.2 A cm −2 with a formation rate of 5,926 μmol h −1 cm −2 . Importantly, within the cathode, these ion-conductive hydrophilic biopolymers can fully substitute traditional hydrophobic ionomers/binders, such as Nafion, challenging previous assumptions about the non-viability of hydrophilic materials for selective CO 2 RR due to excess interfacial H 2 O. These findings unveil key insights into microenvironment design to enhance C–C coupling through a simple method.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Understanding Inlet Concentration Effects on the Electrocatalytic Conversion of CO 2 to Formic Acid in Gas-Fed Electrolyzers

The electrochemical CO 2 reduction reaction (CO2RR) to produce value-added products remains a developing technology for utilizing waste CO 2 streams. Most device-level CO2RR studies use pure CO 2 gas feeds; however, the effect of dilute CO 2 on the electrolyzer performance is an important consideration for large-scale electrolyzer operation, single-pass conversion, and real-world CO 2 source utilization. This work investigates the effect that the CO 2 concentration has on the performance of formic acid (HCOOH) producing tin oxide (SnO 2 ) and bismuth oxide (Bi 2 O 3 ) catalysts in an electrolyzer device setting. Surprisingly, SnO2 demonstrated an approximately 20% increase in HCOOH selectivity (Faradaic efficiency) when the CO 2 concentration decreased from 100 to 20%. In contrast, Bi 2 O 3 consistently demonstrated high selectivity toward HCOOH across the same CO 2 concentration range. The effects of the CO 2 concentration on selectivity were further investigated with half-cell experiments and in situ Raman spectroscopy, which revealed dynamic changes in the cathodic overpotential and chemical state of the catalyst that depended on the CO 2 concentration. Density functional theory calculations showed how changes in the surface oxidation state of Sn, varying from fully oxidized SnO 2 to metallic Sn(0), affect the thermodynamic barriers of the three main observed products: HCOOH, CO, and H 2 . Our results indicate that dilute CO 2 concentrations required larger cathodic overpotentials to sustain a fixed current density, which, in turn, pushed the Sn-based catalyst toward a more reduced surface that was favorable to HCOOH formation. On the other hand, the Bi-based catalyst remained in a metallic state at CO2RR-relevant potentials and demonstrated a consistent product selectivity regardless of CO 2 concentration. These findings highlight how varying the CO 2 inlet gas concentrations affects the chemical state of catalysts and the resulting performance metrics.

42 ENGINEERING↗
DOE OSTI2025

Design and Fabrication of a Thyristor Using Ion Implantation of Anode and Cathode

A thyristor is a solid-state semiconductor switch made up of four alternating p and n type layers. When the switch is turned on by a small pulse, current can flow as long as the device stays on. When the voltage drops below the turn on level or the current reverses, the switch will turn off. Thyristors only allow current to flow in one direction. One of the benefits of a thyristor device is in its capacity to conduct large voltages with a small device and a small turn-on pulse requirement. Another distinguishing feature of thyristors compared to other semiconductor devices is that it can only be in the on or off state, there’s no in-between state for the device to exist within. These properties make thyristors very useful as switch devices, especially in applications where current flow is only needed in one direction and could potentially be damaging in the opposite direction. Currently, thyristors are most commonly used to control very high power loads and they are available commercially in many designs to control different amounts of current.

42 ENGINEERING↗
DOE OSTI2026

New Engineering Concepts to High Energy Density Li-S Batteries

Li-S batteries (LSBs) with energy densities > 500 Wh/kg @ C/5 and >1000 cycles, cycle life operating over wide temperatures has been identified to be critical for meeting the global energy demands. Progress is however, very much limited due to several major hurdles related to the following: (a) poor Li' reaction kinetics (conductivity/diffusivity) enabling full reversible S conversion to Li2S, (b) inferior electron (e) conductivity, specific capacity and cycle life due to electrolyte soluble species of polysulfides (PSs) formed with the reaction of Li ions with sulfur migrating to anode, (c) unstable solid electrolyte interphase (SEI) formation and finally, (d) dendrites that are formed on the Li metal anode severely limiting the cycle life due to polarization at the solid/liquid interfaces causing safety, inferior capacity, energy density, rate, and cycle life issues. Creation of a fully functional economical ≤$80/kWh, high energy density LSBs is vital for enabling its widespread commercial deployment and use in current and next generation electric vehicles.

25 ENERGY STORAGE↗
DOE OSTI2025

Impact of SO 2 on NiFe Nanoparticle Exsolution and Dissolution from LaFe 0.9 Ni 0.1 O 3 Perovskite Oxides

Ni-doped LaFeO 3 perovskite oxide is a promising cathode material for solid oxide electrolysis cells (SOECs) designed for CO 2 /H 2 O coelectrolysis. Here, the performance of LaFe 0.9 Ni 0.1 O 3 is being investigated under real-world conditions that include exposure to acid gases, such as SO 2 , relevant to SOEC operation. Experiments show that LaFe 0.9 Ni 0.1 O 3 exsolves NiFe nanoparticles, along with the formation of surface SO 4 2– and SO 3 2– after being exposed to 200 ppm of SO 2 . This suggests that the ionic diffusion of Ni 3+ and Fe 3+ between the bulk and the surface remains unaffected throughout the exsolution–dissolution–exsolution cycle. Thermochemical water splitting has been employed as a probe reaction to evaluate the catalytic properties of the exsolved NiFe nanoparticles. These nanoparticles demonstrated improved hydrogen production compared to bare perovskite oxide substrates. However, after exposure to SO 2 , the formation of Fe-rich NiFe nanoparticles led to poor thermocatalytic performance and rapid deactivation of the perovskite at elevated temperatures. Density functional theory (DFT) analysis was utilized to validate the experimental findings, indicating a significantly negative reaction energy for water splitting over exsolved Fe, as well as stronger binding of SO 2 to Fe than to Ni. Computational analysis further suggests that the presence of surface sulfate promotes the formation of Fe-rich NiFe nanoparticles, aligning with the experimental results. Overall, this study clarifies how SO 2 affects the structure of SOEC perovskite oxide candidate materials. Future engineering efforts should focus on enhancing nanoparticle exsolution and sulfur resistance, which is crucial for improving the hydrogen production capacity of La-based perovskite oxides for electro- and thermocatalytic water splitting in real environments containing acid gases.

Najimu, Musa [Univ. of Southern California, Los An↗