Search NASA⌕ Search

SEARCH · Search NASA

Results for “control layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Fluid-Structure Interactions using Controlled Disturbances on a Slender Cone in Hypersonic Flow

Fluid-structure interactions were studied on a 7° half-angle cone in the Sandia Hypersonic Wind Tunnel at Mach 8 over a range of freestream Reynolds numbers between 3.3 and 14.5 × 10 6 /m. A thin panel with tunable structural natural frequencies was integrated into the cone and exposed to naturally developing boundary layers. An elevated panel response was measured during boundarylayer transition at frequencies corresponding to the turbulent burst rate, and lower vibrations were measured under a turbulent boundary layer. Controlled perturbations from an electrical discharge were then introduced into the boundary layer at varying frequencies corresponding to the structural natural frequencies of the panel. The perturbations were not strong enough to drive a panel response exceeding that due to natural transition. Instead at high repetition rates, the perturber modified the turbulent burst rate and intermittency on the cone and therefore changed the conditions for when an elevated transitional panel vibration response occurred. Studies were also conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel at Purdue University. Under quiet flow, natural transition does not occur, and the controlled perturbations are the only disturbance source. A clear panel response to turbulent spots created by the controlled perturbations was observed at varying frequencies of spot generation. The quiet-flow measurements confirm the clear relationship between turbulent spot passage and panel vibration.

42 ENGINEERING↗

Active Control of Boundary-Layer Instabilities: Use of Sensors and Spectral Controller

Full Navier-Stokes equations were conducted to determine the feasibility of automating the control of wave instabilities within a flat plate boundary layer with sensors, actuators, and a spectral controller. The results indicate that a measure of wave cancellation can be obtained for small and large amplitude instabilities without feedback; however, feedback is required to optimize the control amplitude and phase for exact wave cancellation.

Joslin, R. D.↗

NASA Tech Briefs, September 2004

Topics covered include: Brazing SiC/SiC Composites to Metals; Composite-Material Tanks with Chemically Resistant Liners; Thermally Conductive Metal-Tube/Carbon-Composite Joints; Improved BN Coatings on SiC Fibers in SiC Matrices; Iterative Demodulation and Decoding of Non-Square QAM; Measuring Radiation Patterns of Reconfigurable Patch Antennas on Wafers; Low-Cutoff, High-Pass Digital Filtering of Neural Signals; Further Improvement in 3DGRAPE; Ground Support Software for Spaceborne Instrumentation; MER SPICE Interface; Simulating Operation of a Planetary Rover; Analyzing Contents of a Computer Cache; Discrepancy Reporting Management System; Silicone-Rubber Microvalves Actuated by Paraffin; Hydraulic Apparatus for Mechanical Testing of Nuts; Heat Control via Torque Control in Friction Stir Welding; Manufacturing High-Quality Carbon Nanotubes at Lower Cost; Setup for Visual Observation of Carbon-Nanotube Arc Process; Solution Preserves Nucleic Acids in Body-Fluid Specimens; Oligodeoxynucleotide Probes for Detecting Intact Cells; Microwave-Spectral Signatures Would Reveal Concealed Objects; Digital Averaging Phasemeter for Heterodyne Interferometry; Optoelectronic Instrument Monitors pH in a Culture Medium; Imaging of gamma-Irradiated Regions of a Crystal; Photodiode-Based, Passive Ultraviolet Dosimeters; Discrete Wavelength-Locked External Cavity Laser; Flexible Shields for Protecting Spacecraft Against Debris; Part 2 of a Computational Study of a Drop-Laden Mixing Layer; Controllable Curved Mirrors Made from Single-Layer EAP Films; and Demonstration of a Pyrotechnic Bolt-Retractor System.

Source record↗

On the stabilization of three-dimensional boundary layers by suction and cooling

A significant reduction in the drag of transonic aircraft can be achieved by using an active method of boundary-layer control to maintain laminar flow on the aerodynamic surfaces. The stabilizing influence of suction for both favorable and adverse pressure gradients is demonstrated by means of the self-similar incompressible three-dimensional boundary layers on yawed wedges. Profile instability is measured by the maximum amplification rate of fixed-frequency disturbances computed according to linearized, locally parallel, spatial stability theory. Suction is found to be more effective in controlling Tollmien-Schlichting instability than stationary cross-flow disturbances. The effectiveness of surface cooling as a method of stabilization is compared with suction for the boundary layers on a transonic 35 deg swept wing of infinite span. It is found from compressible stability theory that when the surface is cooled to a uniform temperature such that the maximum cross-flow velocity is reduced by the same amount as with a uniform suction distribution, the stabilizing effect of cooling on cross-flow disturbances is less than with suction.

Mack, L. M.↗

The passive control of compressible boundary layer growth by boundary layer trips

The passive control of compressible boundary layer growth by boundary layer trips has been studied experimentally. Axisymmetric trips and three dimensional trips were used in this study. The nomial freestream Mach numbers are 1.5 and 4. The results show that trips are effective in promoting boundary layer growth. Trips are more effective for Mach 1.5 flows than for Mach 4 flows.

Chou, J. H.↗

Control of Supersonic Boundary Layers Using Steady Suction

Control of supersonic boundary layers using steady suction through a series of very small two-dimensional strips is numerically investigated at a free stream Mach number of 1.8. The mean flow induced by rows of suction holes is also computed. Both the steady and unsteady solutions are obtained by solving the full Navier-Stokes equations using the 5th-order accurate weighted essentially non-oscillatory (WENO) scheme for space discretization and using third-order total-variationdiminishing (TVD) Runge-Kutta scheme for time integration. Computations for the two-dimensional cases are performed at suction coefficients 0.001 and 0.002 to investigate the stabilizing effects of suction. The simulation showed that a series of shock waves are generated at the slots. The stability results showed that the total amplification is reduced up to the end of the computational domain. However, the growth rates become larger at downstream distances away from the suction region. The computations for the suction holes showed the generation of Mach waves from each hole and the formation of longitudinal vortices.

Balakumar, P.↗

Maneuver Performance Enhancement for an Advanced Fighter/Attack Aircraft

A small scale wind tunnel test of a realistic fighter configuration has been completed in NASA Ames' 7'x10' wind tunnel. This test was part of the Fighter Lift and Control (FLAC) program, a joint NASA - USAF research program, involving small and large-scale wind-tunnel tests and computational analysis of unique lift augmentation and control devices. The goal of this program is to enhance the maneuver and control capability of next-generation Air Force multi-role fighter aircraft with low-observables geometries. The principal objective of this test was to determine the effectiveness of passive boundary layer control devices at increasing L/D at sustained maneuver lift coefficients. Vortex generators (VGs) were used to energize the boundary layer to prevent or delay separation. Corotating vanes, counter-rotating vanes, and Wheeler Wishbone VGs were used in the vicinity of the leading and trailing edge flap hinge lines. Principle test parameters were leading and trailing edge flap deflections, and location, size, spacing, and orientation for each VG type. Gurney flaps were also tested. Data gathered include balance force and moment data, surface pressures, and flow visualization for characterizing flow behavior and locating separation lines. Results were quite different for the two best flap configurations tested. All VG types tested showed improvement (up to 5%) in maneuver L/D with flaps at LE=20 degrees, TE=0 degrees. The same VGs degraded performance, in all but a few cases, with flaps at LE=15 degrees, TE=10 degrees.

Samuels, Jeff↗

Controls for Electrified Aircraft Propulsion

Advanced electrified aircraft propulsion (EAP) concepts with integrated power, propulsion, and thermal systems require the development of equally sophisticated controllers to fly safe and efficient missions. Hybrid electric aircraft utilize electric machines mechanically coupled to the engine shafts to extract and insert power for a variety of purposes. Additionally, electric machines may drive propulsive fans pulling from a combination of on-board energy storage devices and engine extracted power. NASA’s investment in hybrid electric aircraft hardware-in-the-loop testing enables controls research on representative engine models using a novel emulation and scaling methodology. High-voltage, high-power electrical powertrain presents several technical risks at altitude. High-power requires high efficiency to minimize losses. Superconducting electric machines and power distribution research at NASA has identified key challenges with potential controls solutions. These risks necessitate the development of controllers robust to model uncertainty, disturbances, and fault conditions. System health management and fault detection schemes play an important role in a multi-layer controls approach that utilizes a supervisor which oversees inner loops for the highly coupled power, propulsion, and thermal systems. Such a supervisory controller enables coordinates energy transfer between engines, energy storage devices, electric machines, propulsors, and heat exchangers. Existing methods have shown an improvement in engine operability using the hybrid electric powertrain.

Halle E Buescher↗

Phasor-Based Control for Scalable Solar PV Integration

This project demonstrated that solar PV can be recruited to stabilize the grid, smooth out disturbances, manage power flows, and assist circuit switching operations. It developed a radically new, layered control framework for Distributed Energy Resources (DER) to act in response to real-time, measured conditions on their local distribution circuit, rather than waiting for a price signal to indicate preferred behavior. By enabling resources to act as good citizens on the electric grid, Phasor-Based Control (PBC) facilitates arbitrarily high solar penetration levels.

14 SOLAR ENERGY↗

Development of Advanced Casing Treatments for Flow Control

Under the Base R&T and Ultra Efficient Engine Technology programs, the NASA-Goddard Space Flight Center Compressor Branch is investigating flow control strategies required to increase the loading and efficiency of core compressors while maintaining current levels of operability. Flow-control strategies being studied include advanced casing treatments, wall jet injection, and blade-tip injection for compressor stability enhancement, directed jets for surface boundary layer control, and vortex-generating devices. The use of computational fluid dynamics (CFD) simulations to assess the effectiveness of flow-control devices and to guide their design is a key element in this research. CFD simulations serve to screen potential flow-control concepts at a lower cost than executing physical experiments in turbomachinery facilities. CFD simulations also provide guidance in designing physical experiments for those flow control concepts, which appear promising.

Keith, Theo G., Jr.↗

Laser Inertial Fusion Energy Control Systems

A Laser Inertial Fusion Energy (LIFE) facility point design is being developed at LLNL to support an Inertial Confinement Fusion (ICF) based energy concept. This will build upon the technical foundation of the National Ignition Facility (NIF), the world's largest and most energetic laser system. NIF is designed to compress fusion targets to conditions required for thermonuclear burn. The LIFE control systems will have an architecture partitioned by sub-systems and distributed among over 1000's of front-end processors, embedded controllers and supervisory servers. LIFE's automated control subsystems will require interoperation between different languages and target architectures. Much of the control system will be embedded into the subsystem with well defined interface and performance requirements to the supervisory control layer. An automation framework will be used to orchestrate and automate start-up and shut-down as well as steady state operation. The LIFE control system will be a high parallel segmented architecture. For example, the laser system consists of 384 identical laser beamlines in a 'box'. The control system will mirror this architectural replication for each beamline with straightforward high-level interface for control and status monitoring. Key technical challenges will be discussed such as the injected target tracking and laser pointing feedback. This talk discusses the the plan for controls and information systems to support LIFE.

42 ENGINEERING↗

Phasor-Based Control for Scalable Solar PV Integration (Final Technical Report)

This project demonstrated that solar PV can be recruited to stabilize the grid, smooth out disturbances, manage power flows, and assist circuit switching operations. It developed a radically new, layered control framework for Distributed Energy Resources (DER) to act in response to real-time, measured conditions on their local distribution circuit, rather than waiting for a price signal to indicate preferred behavior. By enabling resources to act as good citizens on the electric grid, Phasor-Based Control (PBC) facilitates arbitrarily high solar penetration levels.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Model Predictive Control of the Exit Part Temperature for an Austenitization Furnace

Quench hardening is the process of strengthening and hardening ferrous metals and alloys by heating the material to a specific temperature to form austenite (austenitization), followed by rapid cooling (quenching) in water, brine or oil to introduce a hardened phase called martensite. The material is then often tempered to increase toughness, as it may decrease from the quench hardening process. The austenitization process is highly energy-intensive and many of the industrial austenitization furnaces were built and equipped prior to the advent of advanced control strategies and thus use large, sub-optimal amounts of energy. The model computes the energy usage of the furnace and the part temperature profile as a function of time and position within the furnace under temperature feedback control. In this paper, the aforementioned model is used to simulate the furnace for a batch of forty parts under heuristic temperature set points suggested by the operators of the plant. A model predictive control (MPC) system is then developed and deployed to control the the part temperature at the furnace exit thereby preventing the parts from overheating. An energy efficiency gain of 5.3% was obtained under model predictive control compared to operation under heuristic temperature set points tracked by a regulatory control layer.

36 MATERIALS SCIENCE↗

Study of Semi-Span Model Testing Techniques

An investigation has been conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel in order to further the development of semi-span testing capabilities. A twin engine, energy efficient transport (EET) model with a four-element wing in a takeoff configuration was used for this investigation. Initially a full span configuration was tested and force and moment data, wing and fuselage surface pressure data, and fuselage boundary layer measurements were obtained as a baseline data set. The semi-span configurations were then mounted on the wind tunnel floor, and the effects of fuselage standoff height and shape as well as the effects of the tunnel floor boundary layer height were investigated. The effectiveness of tangential blowing at the standoff/floor juncture as an active boundary-layer control technique was also studied. Results indicate that the semi-span configuration was more sensitive to variations in standoff height than to variations in floor boundary layer height. A standoff height equivalent to 30 percent of the fuselage radius resulted in better correlation with full span data than no standoff or the larger standoff configurations investigated. Undercut standoff leading edges or the use of tangential blowing in the standoff/ floor juncture improved correlation of semi-span data with full span data in the region of maximum lift coefficient.

Gatlin, Gregory M.↗

Non-radiative recombination at dislocations in InAs quantum dots grown on silicon

We study the impact of misfit dislocations on the luminescence from InAs quantum dots (QDs) grown on Si substrates. Electron channeling contrast imaging is used together with cathodoluminescence mapping to locate misfit dislocations and characterize the resulting nonradiative recombination of carriers via near-infrared light emission profiles. With a 5 kV electron beam probe, the dark line defect width due to a typical misfit dislocation in a shallow QD active layer is found to be approximately 1 μ m, with a 40%–50% peak emission intensity loss at room temperature. Importantly, we find that at cryogenic temperatures, the dislocations affect the QD ground state and the first excited state emission significantly less than the second excited state emission. At the same time, the dark line defect width, which partially relates to carrier diffusion in the system, is relatively constant across the temperature range of 10 K–300 K. Our results suggest that carrier dynamics in the QD wetting layer control emission intensity loss at dislocations, and that these defects reduce luminescence only at those temperatures where the probability of carriers thermalizing from the dots into the wetting layer becomes significant. We discuss the implications of these findings toward growing dislocation-tolerant, reliable quantum dot lasers on silicon.

Electron beams↗

Design of a bleed system for a Mach 3.5 inlet

An analytical bleed system design procedure is applied to a Mach 3.5, axisymmetric, translating centerbody inlet. The design features a traveling centerbody bleed system with a ducting arrangement separating low-, medium-, and high-pressure bleed. Three forward plenums and nine throat plenums are installed on the centerbody to meet the bleed requirements in the started Mach range between 1.6 and 3.5. The cowl contains four stationary plenums, three for forward and one for throat bleed. To achieve maximum bleed plenum pressure and thereby minimize bleed drag all bleed holes are inclined 20 deg to the surface except in the cowl throat region. Here the requirement of high stability margin with minimum total pressure recovery penalty resulted in 90 deg bleed holes. The bleed hole diameter varies from bleed plenum to bleed plenum to achieve the most efficient boundary layer control, while the bleed exits are sized to operate at the highest possible plenum pressure without unchoking the bleed holes. Bleed flow rates, bleed plenum pressures, and boundary layer development along the cowl and centerbody are predicted over the entire started Mach range.

Syberg, J.↗

Experimental Investigation of Crossing Shock Wave-Turbulent Boundary Layer-Bleed Interaction

Results of an experimental investigation of a symmetric crossing shock wave/turbulent boundary layer/bleed interaction are presented for a freestream unit Reynolds number of 1.68 x 10(exp 7)/m, a Mach number of 2.81, and deflection angles of 8 degrees. The data obtained in this study are bleed mass flow rate using a trace gas technique, qualitative information in the form of oil flow visualization, flow field Pitot pressures, and static pressure measurements using pressure sensitive paint. The main objective of this test is two-fold. First, this study is conducted to explore boundary layer control through mass flow removal near a large region of separated flow caused by the interaction of a double fin-induced shock wave and an incoming turbulent boundary layer. Also, a comprehensive data set is needed for computational fluid dynamics code validation.

Kim, Hyun↗

Active structural control for damping augmentation and compensation of thermal distortion

A large space-based Focus Mission Interferometer is used as a testbed for the NASA Controls and Structures Interaction Program. Impedance-based adaptive structural control and control of thermal disturbances are demonstrated using an end-to-end simulation of the system's optical performance. Attention is also given to integrated optical/structural modeling and a hierarchical, layered control strategy.

Sirlin, S. W.↗