SEARCH · Search NASA

Results for “data reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS2002

Experimental Investigation of Water Droplet Impingement on Airfoils, Finite Wings, and an S-duct Engine Inlet

Validation of trajectory computer codes, for icing analysis, requires experimental water droplet impingement data for a wide range of aircraft geometries as well as flow and icing conditions. This report presents improved experimental and data reduction methods for obtaining water droplet impingement data and provides a comprehensive water droplet impingement database for a range of test geometries including an MS(1)-0317 airfoil, a GLC-305 airfoil, an NACA 65(sub 2)-415 airfoil, a commercial transport tail section, a 36-inch chord natural laminar flow NLF(1)-0414 airfoil, a 48-inch NLF(1)-0414 section with a 25 percent chord simple flap, a state-of-the-art three-element high lift system, a NACA 64A008 finite span swept business jet tail, a full-scale business jet horizontal tail section, a 25 percent-scale business jet empennage, and an S-duct turboprop engine inlet. The experimental results were obtained at the NASA Glenn Icing Research Tunnel (IRT) for spray clouds with median volumetric diameter (MVD) of 11, 11.5, 21, 92, and 94 microns and for a range of angles of attack. The majority of the impingement experiments were conducted at an air speed of 175 mph corresponding to a Reynolds number of approximately 1.6 million per foot. The maximum difference of repeated tests from the average ranged from 0.24 to 12 percent for most of the experimental results presented. This represents a significant improvement in test repeatability compared to previous experimental studies. The increase in test repeatability was attributed to improvements made to the experimental and data reduction methods. Computations performed with the LEWICE-2D and LEWICE-3D computer codes for all test configurations are presented in this report. For the test cases involving median volumetric diameters of 11 and 21 microns, the correlation between the analytical and experimental impingement efficiency distributions was good. For the median volumetric diameters of 92 and 94-micron cases, however, the analysis produced higher impingement efficiencies and larger impingement limits than the experiment. It is speculated that this discrepancy is due to droplet splashing and breakup experienced by large droplets during impingement.

Papadakis, Michael↗

NASA NTRSDate not supplied

Dynamic Stability Analysis Using Free-Flight CFD

Blunt body probes are the primary design for atmospheric entry. The blunted capsule shape, while desirable for the decreased forebody heating, typically experiences dynamic instability at low supersonic and transonic flight. At moderate to low supersonic conditions, the unsteady wake begins to adversely interact with the vehicle in free-flight resulting in attitude oscillations which can grow in time and result in tumbling. Understanding vehicle dynamics is thus important when considering vehicle entry design and guidance navigation and control (GN&C) considerations. Historically, dynamic stability has been carried out exclusively using experimental techniques. The wide range of experimental approaches provide reasonable coverage in Mach and dynamic pressure space for a given trajectory, however achieving flight similitude is often difficult or impossible. Advancements in Computational Fluid Dynamics (CFD) techniques allow for dynamic motion of the vehicle surface during the simulation with either forced/prescribed motion or free motion in response to fluid forces. Several examples of CFD software with the ability to simulate fluid dynamics and vehicle motion are available in literature. The Free-Flight CFD (FF-CFD) capability developed by NASA Ames within the US3D flow solver has shown extensive validation and verification (V&V) efforts from moderate to low supersonic flow across a range of vehicle architectures. The solver is able to simulate full rotational and translation motion resulting in full 6 degrees-of-freedom (DoF) motion. The validation and verification efforts the solver's ability to predict the motion of a ballistic range model as compared to experimental results. Similar to other computational capabilities in literature, FF-CFD relied on heritage data reduction methodologies and processes for reducing dynamic data into aerodynamic coefficients intended for use in design and trajectory codes. These heritage approaches, initially developed with the assumptions (and restrictions) of ground test facilities, resulted in the significant culling of the full 6-DoF dynamic data set to discrete values which are then fit using an aerodynamic model. Recent development of simulation and data reduction methodologies has resulted in an improved approach to FF-CFD simulations of vehicle dynamics which leverage the control of dynamic constraints within a simulation set-up. The presentation of this work will cover the constrained dynamic simulation approach for deriving dynamic coefficients for a Genesis capsule. The methodology will be outlined and a discussion of implications in motion restriction will be discussed. Finally, reconstructed vehicle trajectories using FF-CFD derived aerodynamic coefficients will be presented.

Joseph M Brock↗

NASA NTRSDate not supplied

Forced Displacement Technique for Measuring Blunt Body Aerodynamics in a Magnetic Suspension Wind Tunnel

The Old Dominion University/NASA Langley 6-Inch Magnetic Suspension Wind Tunnel has developed the ability to levitate blunt bodies which can oscillate freely about the yaw axis. This allows for the measurement of static and dynamic stability coefficients without sting interference. The magneic suspension controller introduces other translational forces which affect the vehicle dynamics complicating data reduction. Exciting model oscillations in a reliable way has also been a challenge. A new test method has been developed that produces capsule oscillations from forced oscillatory translational motion at the resonant yaw oscillatory frequency of the capsule. After oscillations are excited, the translational forcing motion is suspended to record free oscillation behavior as well. A data reduction method whereby a linear model of the translational and oscillatory motion is used to fit to the measured data and solve for aerodynamic coefficients has also been developed. The work presented shows that the new data reduction

blunt body↗

NASA NTRSDate not supplied

Forced Displacement Technique for Measuring Blunt Body Aerodynamics in a Magnetic Suspension Wind Tunnel

blunt body↗

NASA NTRS1988

Plasma diagnostics package. Volume 2: Spacelab 2 section. Part B: Thesis projects

Pickett, Jolene S.↗

NASA NTRS1988

Plasma diagnostics package. Volume 1: OSS-1 section

This volume (1) of the Plasma Diagnostics Package (PDP) final science report contains a summary of all of the data reduction and scientific analyses which were performed using PDP data obtained on STS-3 as a part of the Office of Space Science first payload (OSS-1). This work was performed during the period of launch, March 22, l982, through June 30, l983. During this period the primary data reduction effort consisted of processing summary plots of the data received by the 14 instruments located on the PDP and submitting these data to the National Space Science Data Center (NSSDC). The scientific analyses during the performance period consisted of general studies which incorporated the results of several of the PDP's instruments, detailed studies which concentrated on data from only one or two of the instruments, and joint studies of beam-plasma interactions with the OSS-1 Fast Pulse Electron Generator (FPEG) of the Vehicle Charging and Potential Investigation (VCAP). Internal reports, published papers and oral presentations which involve PDP/OSS-1 data are listed in Sections 3 and 4. A PDP/OSS-1 scientific results meeting was held at the University of Iowa on April 19-20, 1983. This meeting was attended by most of the PDP and VCAP investigators and provided a forum for discussing and comparing the various results, particularly with regard to the shuttle orbiter environment. One of the most important functional objectives of the PDP on OSS-1 was to characterize the orbiter environment.

Pickett, Jolene S.↗

NASA NTRS1988

Plasma diagnostics package. Volume 2: Spacelab 2 section, part A

This volume (2), which consists of two parts (A and B), of the Plasma Diagnostics Package (PDP) Final Science Report contains a summary of all of the data reduction and scientific analyses which were performed using PDP data obtained on STS-51F as a part of the Spacelab 2 (SL-2) payload. This work was performed during the period of launch, July 29, l985, through June 30, l988. During this period the primary data reduction effort consisted of processing summary plots of the data received by 12 of the 14 instruments located on the PDP and submitting these data to the National Space Science Data Center (NSSDC). The scientific analyses during the performance period consisted of follow-up studies of shuttle orbiter environment and orbiter/ionosphere interactions and various plasma particle and wave studies which dealt with data taken when the PDP was on the Remote Manipulator System (RMS) arm and when the PDP was in free flight. Of particular interest during the RMS operations and free flight were the orbiter wake studies and joint studies of beam/plasma interactions with the SL-2 Fast Pulse Electron Generator (FPEG) of the Vehicle Charging and Potential Investigation (VCAP). Internal reports, published papers and presentations which involve PDP/SL-2 data are listed in Sections 3 and 4. A PDP/SL-2 scientific results meeting was held at the University of Iowa on June 10, l986. This meeting was attended by most of the PDP and VCAP investigators and provided a forum for discussing and comparing the various results, particularly with regard to the PDP free flight.

Pickett, Jolene S.↗

NASA NTRS1981

The reduction, verification and interpretation of MAGSAT magnetic data over Canada

Analysis of Investigator B tapes was extended to use a statistical screening of individual data points in each grid cell over the map area. The mean value of data from each cell was computed and all data values more than 4nT from the mean were rejected. The revised mean and standard deviation was computed. The average standard deviation for all map grid cells was 1.4nT for the scalar anomaly map and about 2nT for the vector component anomaly maps. At this stage, the grid cell is larger and spatial resolution lower for the vector maps than for the scalar maps, because the vector components are considerably more disturbed and more data points were rejected. An approach for altitude adjustment is in progress so that corrections can be made and data reduction procede. To evaluate the use of scalar and vector MAGSAT data for the production of regional magnetic charts, charts of the north, east, vertical, and scalar field derived from MAGSAT and from Canadian aeromagnetic data were compared. It appears possible to retrieve crustal signals from the horizontal vector components despite external disturbance fields at high latitude.

Coles, R. L.↗

NASA NTRS1972

An efficient algorithm using matrix methods to solve wind tunnel force-balance equations

An iterative procedure applying matrix methods to accomplish an efficient algorithm for automatic computer reduction of wind-tunnel force-balance data has been developed. Balance equations are expressed in a matrix form that is convenient for storing balance sensitivities and interaction coefficient values for online or offline batch data reduction. The convergence of the iterative values to a unique solution of this system of equations is investigated, and it is shown that for balances which satisfy the criteria discussed, this type of solution does occur. Methods for making sensitivity adjustments and initial load effect considerations in wind-tunnel applications are also discussed, and the logic for determining the convergence accuracy limits for the iterative solution is given. This more efficient data reduction program is compared with the technique presently in use at the NASA Langley Research Center, and computational times on the order of one-third or less are demonstrated by use of this new program.

Smith, D. L.↗

NASA NTRS2002

The Use of Doublers in Delamination Toughness Testing

In this paper, the data reduction equations for common delamination toughness tests are rederived for use with specimens which have bonded doublers. The common toughness tests considered here are the double cantilever beam (DCB) for mode I toughness; the end notch flexure (3ENF) and 4 point ENF (4ENF) for mode II toughness; and the mixed mode bending (MMB) test for testing under combined mode I and mode II loading. Because the addition of the doublers changes the bending stiffness of the specimens, these data reduction equations may need to be corrected. Doublers were added to the delamination test specimens to solve a premature failure problem. Delamination toughness is normally tested using a beam with an imbedded insert so that one end of the specimen is split into two arms. If the specimen is too thin, or if the toughness of the material is too high, an arm of the specimen may fail in bending before the delamination grows. When this occurs, the toughness of the material cannot be determined. To delay the bending failure so that delamination growth occurs, doubler plates were bonded to both top and bottom surfaces of the specimen. A doubler parameter, beta, which describes how much the use of doubler plates changed the ratio of full thickness to delaminated bending stiffnesses, was defined. When changes to the data reduction equations were required, the changes were minor when written in terms of the beta parameter. The doubler plate technique was demonstrated by measuring the mixed-mode fracture toughness of a carbon-carbon composite using test specimens which would otherwise have failed before delamination growth occurred. The doubler plate technique may solve several problems that can be encountered when testing delamination fracture toughness.

Reeder, James R.↗

NASA NTRS1971

Behavior of nozzles and acoustic liners in three dimensional acoustic fields

Theoretical values of the admittances of various nozzles were computed and compared with the corresponding experimental values. The existing data reduction scheme was corrected and all available experimental data has been rechecked and corrected whenever necessary; the updated experimental admittance values are presented. An analysis associated with the frequency sensitivity of experimental admittance values was initiated and the analog-to-digital Data Reduction Program which has become operational is discussed. Fourteen nozzle tests were conducted during this report period.

Zinn, B. T.↗

NASA NTRS1983

Model deformation system

The development of a system to measure model deflections encountered in the National Transonic Facility is discussed. The goal is to be able to measure peak deflections of up to 3 in. with accuracies to within 0.0025 in. over an area 1 m square as the model pitches through an included angle of 30 deg. Stereophotogrammetric techniques are being implemented, with the initial system being an extension of standard techniques. A second system, which will be all electronic, is under development. Both techniques require targets to be strategically placed on the model. Active targets are being developed for location in the model in order to maximize the signal-to-noise ratio and to approximate a point source. Image processing techniques and stereophotogrammetric data reduction programs are being implemented to perform the data reduction tasks.

Holmes, H. K.↗

NASA NTRS1992

CCD surface photometry of galaxies

We present here the results based on analysis of broad band optical images of radio loud and radio quiet galaxies selected from a set of x-ray galaxies. Data reduction techniques, and surface photometry using the IRAF data reduction package are described. The radial surface brightness profile of each galaxy is obtained. The disc, bulge, and nucleus of the galaxy are modeled based on the estimated brightness profile. The model of the galaxy is constructed, which is subtracted from the observed image to enhance the small scale features in the galaxy. Color maps of the galaxy are obtained and compared with those of normal galaxies. The optical properties of the galaxy are compared with its x-ray and radio properties.

Anupama, G. C.↗

NASA NTRS2012

In-Situ Nondestructive Evaluation of Kevlar(Registered Trademark)and Carbon Fiber Reinforced Composite Micromechanics for Improved Composite Overwrapped Pressure Vessel Health Monitoring

NASA has been faced with recertification and life extension issues for epoxy-impregnated Kevlar 49 (K/Ep) and carbon (C/Ep) composite overwrapped pressure vessels (COPVs) used in various systems on the Space Shuttle and International Space Station, respectively. Each COPV has varying criticality, damage and repair histories, time at pressure, and pressure cycles. COPVs are of particular concern due to the insidious and catastrophic burst-before-leak failure mode caused by stress rupture (SR) of the composite overwrap. SR life has been defined [1] as the minimum time during which the composite maintains structural integrity considering the combined effects of stress level(s), time at stress level(s), and associated environment. SR has none of the features of predictability associated with metal pressure vessels, such as crack geometry, growth rate and size, or other features that lend themselves to nondestructive evaluation (NDE). In essence, the variability or surprise factor associated with SR cannot be eliminated. C/Ep COPVs are also susceptible to impact damage that can lead to reduced burst pressure even when the amount of damage to the COPV is below the visual detection threshold [2], thus necessitating implementation of a mechanical damage control plan [1]. Last, COPVs can also fail prematurely due to material or design noncompliance. In each case (SR, impact or noncompliance), out-of-family behavior is expected leading to a higher probability of failure at a given stress, hence, greater uncertainty in performance. For these reasons, NASA has been actively engaged in research to develop NDE methods that can be used during post-manufacture qualification, in-service inspection, and in-situ structural health monitoring. Acoustic emission (AE) is one of the more promising NDE techniques for detecting and monitoring, in real-time, the strain energy release and corresponding stress-wave propagation produced by actively growing flaws and defects in composite materials [3,4,5,6,7,8]. To gain further insight into the mechanisms responsible for composite rupture, broadband modal acoustic emission analysis was used. Also, since AE data reduction proved to be very time consuming, specialized data reduction software was written to automate the process.

Waller, Jess↗

NASA NTRS1988

Complete positive ion, electron, and ram negative ion measurements near Comet Halley (COPERNIC) plasma experiment for the European Giotto Mission

Participation of U.S. scientists on the COPERNIC (COmplete Positive ions, Electrons and Ram Negative Ion measurements near Comet Halley) plasma experiment on the Giotto mission is described. The experiment consisted of two detectors: the EESA (electron electrostatic analyzer) which provided three-dimensional measurements of the distribution of electrons from 10 eV to 30 keV, and the PICCA (positive ion cluster composition analyzer) which provided mass analysis of positively charged cold cometary ions from mass 10 to 210 amu. In addition, a small 3 deg wide sector of the EESA looking in the ram direction was devoted to the detection of negatively charged cold cometary ions. Both detectors operated perfectly up to near closest approach (approx. 600 km) to Halley, but impacts of dust particles and neutral gas on the spacecraft contaminated parts of the data during the last few minutes. Although no flight hardware was fabricated in the U.S., The U.S. made very significant contributions to the hardware design, ground support equipment (GSE) design and fabrication, and flight and data reduction software required for the experiment, and also participated fully in the data reduction and analysis, and theoretical modeling and interpretation. Cometary data analysis is presented.

Lin, Robert P.↗

DOE OSTI2024

Adaptive Methods for Radial Basis Functions

Radial basis functions (RBFs) are a powerful tool for constructing high-order accurate reduced representations of scattered data in arbitrary dimension and on manifolds. We present a method of constructing data approximations in which we utilize a functional tail to capture a global background profile and a RBF neural network (NN) to capture the smaller-scale features. In the RBF NN the RBF centers, matrix shape parameters were selected adaptively for each RBF. We also utilized a geodesic notion of distance on the manifold on which the data lies, e.g., the spherical geodesic for data on the sphere. Although each of these ideas have been been investigated separately in previous works, their combination into a single algorithm is novel. We defined a machine learning problem in which these properties are learned to minimize the data reduction error. We demonstrate the algorithm for applications of scattered data reduction in the plane and on the sphere.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1991

Methods for obtaining and reducing experimental droplet impingement data on arbitrary bodies

Experimental water droplet impingement data are used to validate particle trajectory computer codes used in the analysis and certification of aircraft de-icing/anti-icing systems. Water droplet impingement characteristics of aerodynamic surfaces are usually obtained from wind-tunnel dye tracer experiments. This paper presents a dye tracer method for measuring water droplet impingement characteristics on arbitrary geometries and a new data reduction method, based on laser reflectance measurements, for extracting impingement data. Extraction of impingement data has been a very time-consuming process in the past. The new data reduction method developed is at least an order of magnitude more efficient than the method previously used. The accuracy of the method is discussed and results obtained are presented.

Papadakis, Michael↗

NASA NTRS2006

Rapid, Repeat-sample Monitoring of Crustal Deformations and Environmental Phenomena with the Uninhabited Aerial Vehicle Synthetic Aperture Radar

The Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) is a precision repeat-pass Interferometric Synthetic Aperture Radar (InSAR) mission being developed by the Jet Propulsion Laboratory and the Dryden Flight Research Center in support of NASA s Science Mission Directorate. UAVSAR's unique ability to fly a repeatable flight path, along with an electronically steerable array, allows interferometric data to be obtained with accuracies measured in millimeters. Deploying the radar on an airborne platform will also allow for radar images to be collected and compared with images from the same area taken hours or even years later - providing for long-term trending and near real-time notification of changes and deformations. UAVSAR s data processing algorithms will provide for near-real time data reduction providing disaster planning and response teams with highly accurate data to aid in the prediction of, and response to, natural phenomena. UAVSAR data can be applied to increasing our understanding of the processes behind solid earth, cryosphere, carbon cycle and other areas of interest in earth science. Technologies developed for UAVSAR may also be applicable to a future earth-orbiting InSAR mission and possibly for missions to the Moon or Mars. The UAVSAR is expected to fly on a Gulfstream III aircraft this winter, followed by a flight test program lasting until the second half of 2007. Following radar calibration and data reduction activities, the platform will be ready for science users in the summer of 2008.

Smith, Robert C.↗