Search NASA⌕ Search

SEARCH · Search NASA

Results for “deformation function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Time dependent deformation of a basalt at low differential stress

A detailed study of linear elastic deformation in Ralston basalt during triaxial loading has been made as a function of strain rate (8 x 10 to the -8th per sec to 5 x 10 to the -5th per sec) and moisture content under constant confining pressure (500 bars) and temperature (20 C). Young's modulus was found to be constant and independent of moisture content and strain rate; however, Poisson's ratio decreased 5.7 plus or minus 1.6% and 6.7 plus or minus 1.6% per order of magnitude increase in strain rate for two suites of dry samples and 1.4 plus or minus 1.2% per equivalent change in strain rate for one suite of wet rocks. Lateral expansion in dry rocks is therefore a more sensitive function of strain rate than it is in wet rocks. It is suggested that this strain-rate dependence is related to microcracking.

Brodsky, N.↗
NASA NTRS1981

The influence of environmental effects on the mechanical properties of graphite/epoxy laminates

The time dependent deformational and creep rupture processes in graphite/epoxy laminates are examined as a function of temperature and stress level. The role of accelerated characterization of design materials is discussed, and the use of a nonlinear time-temperature-stress-superposition principle in the determination of compliance master curves as a function of stress and temperature is considered. Creep rupture analytical models are discussed as applied to polymer-matrix composites, and the data is shown to be in general agreement with a logarithmic stress and temperature-dependent delayed fracture model. Comparisons between creep and rupture experiments and phenomenological models are presented.

Brinson, H. F.↗
NASA NTRS1988

Friction of ice

Frictional sliding experiments were performed on saw-cut samples of laboratory-made polycrystalline water ice, prepared in the same way as the material used by Kirby et al. (1987) in ice deformation experiments. The data show that the maximum frictional stress is a function of the normal stress but is not measurably dependent on temperature or sliding rate over the ranges covered in these experiments (77-115 K and 0.0003-0.03 mm/s, respectively). The sliding behavior was invariably stick slip, with the sliding surfaces exhibiting only minor gouge development. In samples with anomalously low strength, a curious arrangement of densely packed short vertical fractures was observed. The results of these experiments were applied to a model of near-surface tectonic activity on Ganymede, one of Jupiter's icy moons. The results indicate that a global expansion on Ganymede of 3 linear percent will cause extensional movement on preexisting faults at depths to 7 + or - 3 km.

Beeman, M.↗
NASA NTRS1990

Creep and creep rupture of strongly reinforced metallic composites

A creep and creep damage theory is presented for metallic composites with strong fibers. Application is to reinforced structures in which the fiber orientation may vary throughout but a distinct fiber direction can be identified locally (local transverse isotropy). The creep deformation model follows earlier work and is based on a flow potential function that depends on invariants reflecting stress and the material symmetry. As the focus is on the interaction of creep and damage, primary creep is ignored. The creep rupture model is an extension of continuum damage mechanics and includes an isochronous damage function that depends on invariants specifying the local maximum transverse tension and the maximum longitudinal shear stress. It is posited that at high temperature and low stress, appropriate to engineering practice, these stress components damage the fiber/matrix interface through diffusion controlled void growth, eventually causing creep rupture. Experiments are outlined for characterizing a composite through creep rupture tests under transverse tension and longitudinal shear. Application is made to a thin-walled pressure vessel with reinforcing fibers at an arbitrary helical angle. The results illustrate the usefulness of the model as a means of achieving optimal designs of composite structures where creep and creep rupture are life limiting.

Robinson, D. N.↗
NASA NTRS1991

Nonlinear magnetohydrodynamics by Galerkin-method computation

A fully spectral numerical code is used to explore the properties of voltage-driven dissipative magnetofluids inside a periodic cylinder with circular cross section. The trial functions are orthonormal eigenfunctions of the curl (Chandrasekhar-Kendall functions). Transitions are observed from axisymmetric resistive equilibria without flow to helically deformed laminar states with flow, and between pairs of helical laminar states with different pairs of poloidal and toroidal m and n numbers. States of minimum energy dissipation rate seem to be preferred. At high values of the pinch ratio, fully developed magnetohydrodynamic turbulence is observed.

Shan, Xiaowen↗
NASA NTRS1992

Discontinuously reinforced intermetallic matrix composites via XD synthesis

A review is given of recent results obtained for discontinuously reinforced intermetallic matrix composites produced using the XD process. Intermetallic matrices investigated include NiAl, multiphase NiAl + Ni2AlTi, CoAl, near-gamma titanium aluminides, and Ll2 trialuminides containing minor amounts of second phase. Such mechanical properties as low and high temperature strength, compressive and tensile creep, elastic modulus, ambient ductility, and fracture toughness are discussed as functions of reinforcement size, shape, and volume fraction. Microstructures before and after deformation are examined and correlated with measured properties. An observation of interest in many of the systems examined is 'dispersion weakening' at high temperatures and high strain rates. This behavior is not specific to the XD process; rather similar observations have been reported in other discontinuous composites. Proposed mechanisms for this behavior are presented.

Kumar, K. S.↗
NASA NTRS1994

Idealized textile composites for experimental/analytical correlation

Textile composites are fiber reinforced materials produced by weaving, braiding, knitting, or stitching. These materials offer possible reductions in manufacturing costs compared to conventional laminated composites. Thus, they are attractive candidate materials for aircraft structures. To date, numerous experimental studies have been performed to characterize the mechanical performance of specific textile architectures. Since many materials and architectures are of interest, there is a need for analytical models to predict the mechanical properties of a specific textile composite material. Models of varying sophistication have been proposed based on mechanics of materials, classical laminated plate theory, and the finite element method. These modeling approaches assume an idealized textile architecture and generally consider a single unit cell. Due to randomness of the textile architectures produced using conventional processing techniques, experimental data obtained has been of limited use for verifying the accuracy of these analytical approaches. This research is focused on fabricating woven textile composites with highly aligned and accurately placed fiber tows that closely represent the idealized architectures assumed in analytical models. These idealized textile composites have been fabricated with three types of layer nesting configurations: stacked, diagonal, and split-span. Compression testing results have identified strength variations as a function of nesting. Moire interferometry experiments are being used to determine localized deformations for detailed correlation with model predictions.

Adams, Daniel O.↗
NASA NTRS1997

Misperceptions of angular velocities influence the perception of rigidity in the kinetic depth effect

Accuracy in discriminating rigid from nonrigid motion was investigated for orthographic projections of three-dimension rotating objects. In 3 experiments the hypothesis that magnitudes of angular velocity are misperceived in the kinetic depth effect was tested, and in 4 other experiments the hypothesis that misperceiving angular velocities leads to misperceiving rigidity was tested. The principal findings were (a) the magnitude of perceived angular velocity is derived heuristically as a function of a property of the first-order optic flow called deformation and (b) perceptual performance in discriminating rigid from nonrigid motion is accurate in cases when the variability of the deformations of the individual triplets of points of the stimulus displays favors this interpretation and not accurate in other cases.

NASA Center ARC↗
NASA NTRS1993

A nonlinear theory for spinning anisotropic beams using restrained warping functions

A geometrically nonlinear theory is developed for spinning anisotropic beams having arbitrary cross sections. An assumed displacement field is developed using the standard 3D kinematics relations to describe the global beam behavior supplemented with an additional field that represents the local deformation within the cross section and warping out of the cross section plane. It is assumed that the magnitude of this additional field is directly proportional to the local stress resultants. In order to take into account the effects of boundary conditions, a restraining function is introduced. This function plays the role of reducing the amount of free warping deformation throughout the field due to the restraint of the cross section(s) at the end(s) of the beam, e.g., in the case of a cantilever beam. Using a developed ordering scheme, the nonlinear strains are calculated to the third order. The FEM is developed using the weak form variational formulation. Preliminary interesting numerical results have been obtained that indicate the role of the restraining function in the case of a cantilever beam with circular cross section. These results are for the cases of a tip displacement (static) and free vibration studies for both isotropic and anisotropic materials with varied fiber orientations.

Ie, C. A.↗
DOE OSTI2026

Short and medium range structure in elastic deformation of metallic and covalent glasses

Here, we present a concise methodology to analyze structural response to the applied stress in amorphous solids, including metallic glasses (MG), glassy selenium, silica and polycarbonate, using high energy x-ray diffraction and atomic pair distribution function (PDF) analysis. To assess the structural anisotropy induced by applied axial stress, diffraction data were expanded into spherical harmonics. Using Bessel transformation, components of the structure function were converted into isotropic and anisotropic PDFs. The PDFs were compared to the expected model behavior for ideal elastic deformation to separate homogeneous affine strain from local non-affine strains. In metallic glass the range of non-affine deformation is limited to the nearest neighbor shell, suggesting local strain relaxation under stress that occurs even in the elastic regime. Beyond the second atomic shell strain is uniform. However, in glassy silica, polycarbonate and selenium strong local bonding inhibits local displacements and strain in short range order is accommodated by rotation of local units. Interestingly, beyond a molecular unit, deformation in covalent systems is similar to MG, and response of the medium range order scales with the macroscopic stress.

glassy structure↗
DOE OSTI2021

Atomic Gradient Structure Alters Electronic Structure in 3D across the Bulk and Enhances Photoactivity

Abstract Understanding structure–function relationships enables the design of materials with tailored functionalities. The long‐standing challenge is to design materials with high active volume to improve efficiency. Tailored grain boundaries and lattice defects are traditionally used to tune the electronic structure near interfaces or defects to promote electron and hole separation. However, the active volume of point defect sites or interfaces in these traditional photocatalysts is extremely low. This study reports a structure with continuous atomic positional deformation across the bulk, altering the electronic structure in 3D and creating a significantly higher active volume. Such a structure in anatase is obtained and tuned by phase transformation during the heating process. Transmission electron microscopy and density functional theory results reveal that atomic deformations result in continuous band bending across the particles, facilitating electron–hole separation, inhibiting their recombination, and inducing dramatically enhanced photoactivity. These findings enable a different materials design paradigm that can potentially be harnessed for a broad range of applications.

Ren, Peng↗
DOE OSTI2023

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic Gradient Structures: Atomic Gradient Structure Alters Electronic Structure in 3D across the Bulk and Enhances Photoactivity

Understanding structure–function relationships enables the design of materials with tailored functionalities. The long-standing challenge is to design materials with high active volume to improve the efficiency. Tailored grain boundaries and lattice defects are traditionally used to tune the electronic structure near interfaces or defects to promote electron and hole separation. However, the active volume of point defect sites or interfaces in these traditional photocatalysts is extremely low. In this work, we report a structure with continuous atomic positional deformation across the bulk, altering the electronic structure in three-dimension and creating a significantly high active volume. Such a structure in anatase is obtained and tuned by phase transformation during heating process. Transmission electron microscopy and density functional theory results reveal that atomic deformations result in continuous band bending across the particles, facilitating electron–hole separation, inhibiting their recombination, and inducing dramatically enhanced photoactivity. These findings enable a different materials design paradigm that can potentially be harnessed for a broad range of applications.

TiO2↗
NASA NTRS1981

A multi-purpose method for analysis of spur gear tooth loading

A large digitized approach was developed for the static and dynamic load analysis of spur gearing. An iterative procedure was used to calculate directly the "variable-variable" gear mesh stiffness as a function of transmitted load, gear tooth profile errors, gear tooth deflections and gear hub torsional deformation, and position of contacting profile points. The developed approach can be used to analyze the loads, Hertz stresses, and PV for the normal and high contrast ratio gearing, presently the modeling is limited to the condition that for a given gear all teeth have identical spacing and profiles (with or without surface imperfections). Certain types of simulated sinusoidal profile errors and pitting can cause interruptions of the gear mesh stiffness function and, thus, increase the dynamic loads in spur gearing. In addition, a finite element stress and mesh subprogram was developed for future introduction into the main program for calculating the gear tooth bending stresses under dynamic loads.

Kasuba, R.↗
DOE OSTI2024

Mechanochemically responsive polymer enables shockwave visualization

Abstract Understanding the physical and chemical response of materials to impulsive deformation is crucial for applications ranging from soft robotic locomotion to space exploration to seismology. However, investigating material properties at extreme strain rates remains challenging due to temporal and spatial resolution limitations. Combining high-strain-rate testing with mechanochemistry encodes the molecular-level deformation within the material itself, thus enabling the direct quantification of the material response. Here, we demonstrate a mechanophore-functionalized block copolymer that self-reports energy dissipation mechanisms, such as bond rupture and acoustic wave dissipation, in response to high-strain-rate impacts. A microprojectile accelerated towards the polymer permanently deforms the material at a shallow depth. At intersonic velocities, the polymer reports significant subsurface energy absorption due to shockwave attenuation, a mechanism traditionally considered negligible compared to plasticity and not well explored in polymers. The acoustic wave velocity of the material is directly recovered from the mechanochemically-activated subsurface volume recorded in the material, which is validated by simulations, theory, and acoustic measurements. This integration of mechanochemistry with microballistic testing enables characterization of high-strain-rate mechanical properties and elucidates important insights applicable to nanomaterials, particle-reinforced composites, and biocompatible polymers.

Science & Technology - Other Topics↗
DOE OSTI2023

Hexadecapole strength in the rare isotopes 74,76 Kr

In the Ge-Sr mass region, isotopes with neutron number N ≤ 40 are known to feature rapid shape changes with both nucleon number and angular momentum. To gain new insights into their structure, inelastic proton scattering experiments in inverse kinematics were performed on the rare isotopes 74,76 Kr. This work focuses on observables related to the J π = $4$$^{+}_{1}$ states of the Kr isotopes and, in particular, on the hexadecapole degree of freedom. By performing coupled-channels calculations, hexadecapole deformation parameters β 4 were determined for the J π = $4$$^{+}_{1}$ states of 74,76 Kr from inelastic proton scattering cross sections. Two possible coupled-channels solutions were found. A comparison to predictions from nuclear energy density functional theory, employing both non-relativistic and relativistic functionals, clearly favors the large, positive β 4 solutions. These β 4 values are unambiguously linked to the well deformed prolate configuration. Given the β 2 - β 4 trend, established in this work, it appears that β 4 values could provide a sensitive measure of the nuclear shell structure.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Inferring fracture dilation and shear slip from surface deformation utilising trained surrogate models

An important task in energy and CO 2 storage (sequestration) in the subsurface is to verify that the surrounding fractures and faults are not activated, acting as leakage pathways. This is achievable through effective and efficient Measurement, Monitoring and Verification (MMV) plans. In this work, two surrogate models are trained to captures dilation (opening) and shear deformation of fractures, and the associated surface deformation. The trained surrogate model, based on conditional Generative-Adversarial Networks (cGAN) receives fracture apertures from dilational fractures together with fracture slips from shear fractures and predicts the combined surface deformation. An inversion algorithm based on Bayesian framework is proposed to identify the geometry of both types of fractures, as well as volume of dilational fractures and deformation moment induced by shear fractures, all from the measured surface deformation data. The inversion algorithm utilises the Differential Evolution (DE) optimisation technique that has the superior performance in finding the global minimum of cost function. The proposed surrogate-assisted inversion successfully inferred the unknown dip, dip direction and the volume of the dilational fractures as well as the induced deformation moment in shear fractures. The model was further tested for the inversion of a field hydraulic fracturing tilt dataset applying different scenarios with varying unknowns to show the model's performance, as well as incorporating shear deformation for better match with the observed data.

Dilation and shear↗
DOE OSTI2025

Chromium enhances the mechanical performance of 3d transition metal high entropy alloys

A comprehensive examination of the compositional effects on the deformation behavior of high entropy alloys (HEAs) was conducted through nanoindentation, indentation creep, and stress relaxation experiments at ambient temperature. The alloys investigated included NiCoFe, NiCoCr, NiCoCrFe, and NiCoCrFeMn, all of which underwent identical thermomechanical processing. From the experimental results, NiCoCr exhibited the highest maximum shear stress for dislocation nucleation (13 GPa) and nanoindentation hardness (3.8 GPa) among the alloys tested. It also showed the lowest stress sensitivity (0.02) and activation volume (3–4 b 3 ) under creep and stress relaxation conditions, indicative of its superior plastic flow properties. Density functional theory (DFT) calculations further revealed an uneven charge density and larger bonding-length variation in NiCoCr due to the presence of Cr, which increased lattice distortion, impeding dislocation movement. Furthermore, in this study, post-deformation microscopy using transmission electron microscopy (TEM) revealed a high density of stacking faults and twins in NiCoCr that effectively enhanced its creep strength. The results highlight the significance of specific elemental effects, particularly from Cr in this study, over configurational entropy effect (i.e., compositional complexity) in governing the deformation microstructure and mechanical properties of HEAs. Finally, these insights will be instrumental for the design and optimization of advanced alloys for load-bearing applications.

36 - MATERIALS SCIENCE↗