Search NASA⌕ Search

SEARCH · Search NASA

Results for “delay”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Transition Delay via Vortex Generators in a Hypersonic Boundary Layer at Flight Conditions

The potential of realizable, stationary streaks undergoing non-modal growth to stabilize a hypersonic boundary-layer flow and, subsequently, delay the laminar-turbulent transition onset, is studied via numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach number of 5.30, freestream unit Reynolds number equal to 13.42 x 10(exp 6)/m, and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the test article. This paper investigates flow modifications induced by wall-mounted vortex generators (VGs), followed by an analysis of the modal instability of the perturbed, streaky boundary-layer flow. Results are presented both for a single array of VGs that was designed on the basis of optimal growth theory and for a VG configuration involving two separate arrays with opposite orientations that ware designed to provide staged control of flow instabilities while simultaneously reducing the amplification of streak instabilities resulting from the control devices. Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment, which did not include any control devices, correlated with an amplification factor of N = 14.7 for the planar Mack modes. If one assumes that the transition N -factor is not affected by the introduction of the VGs, then the control configurations based on a single array of VGs and two separate arrays would result in a transition delay of 17% and 40%, respectively. These findings suggest a passive flow control s to induce streaks that would delay transition in hypersonic boundary dominated by Mack-mode instabilities.

Incompressible boundary layer↗
NASA NTRSDate not supplied

Towards Sheaf Theoretic Analyses for Delay Tolerant Networking

The goal of Delay Tolerant Networking (DTN) is to take a collection of heterogeneous, disparate connections between satellites, space assets, ground stations, and ground infrastructure and bring it together into a cohesive, functioning overlay network. Depending on the systems being considered, one can find links with a one-way light time exceeding minutes (and hours),periodic links which can sometimes be predicted by orbital mechanics, and restrictions based on the variety of capabilities built into these systems. These characteristics preclude traditional network models and routing techniques and have classically led to either rigid routing tables or purely probabilistic models. As the deeper underlying structures remain unknown, development of more DTN-optimized algorithms has lacked the necessary foundation. In a continuation of previous work, the goal of this paper is to identify and study these fundamental structures that exist in delay tolerant networks (DTN), with a focus on space networks. The current routing methodology has been to use contact graph routing (CGR) algorithms. CGR models a series of known contacts as a static graph. For CGR to work, this graph must be globally consistent and must have an accurate picture of the network. Because this is a globally controlled structure, there is little room for flexibility in the event of changes to the network which would naturally occur as the network grows. As a response to the desire for flexibility as the network changes, we introduced the mathematical structure known as sheaves to DTNs last year. The tag-line for sheaves is that they are a mathematically precise way of gluing local data together into unique global data. Thus, sheaves lend extra power to traditional models(and routing algorithms) by taking additional information and merging it, in as consistent a manner as possible, with the representation itself. The clearest example of how Earth-bound networks exhibit behavior that is “sheafy” is link state routers, which build a local-to-global picture of their network by gluing local information together into a global network, exactly as a sheaf would do. For routing within delay tolerant networks to truly exploit this structure, a deeper structure than a graph is required. In this paper, we develop sheaves that can work over directed graphs such as temporal flow networks, we construct a sheaf representation for Dijkstra’s algorithm, and we outline a construction for routing sheaves capable of modeling multicast scenarios. Finally, there is a section of future work suggesting follow-on research.

Robert Short↗
NASA NTRSDate not supplied

A Distributed Approach to High-Rate Delay Tolerant Networking Within a Virtualized Environment

The High-Rate Delay Tolerant Networking (HDTN) project has taken a distributed service-based approach to the development of a highly efficient delay tolerant networking (DTN) implementation. Through the analysis of many DTN implementations, system and mission requirements as well as the DTN protocol specifications, HDTN has worked to infuse modern computing technologies into the NASA approach to interplanetary networking. The initial use case of the HDTN software runs on a hypervisor representative of the International Space Station (ISS) DTN Gateway. In this scenario, multiple emulated payloads will send science data through HDTN to a mission operations center. HDTN will provide store and forward capability as well as network flow management. This paper discusses the infusion path of cognitive networking technologies in the NASA Space Communications and Navigation (SCaN) networks using the DTN architecture and protocols as the basis for cognitive routing and network management capabilities. HDTN has been developing the Bundle Protocol encoding and decoding mechanisms and messaging framework that can be used as the basis for integrating DTN with various learning and decision-making processes. The concepts of distributed computing, network virtualization, software defined networking and delay tolerant networking are basic building blocks which will further the development of cognitive networking. In addition to discussion of the HDTN software development and testing, this paper examines the role that each of these technologies play in the evolution of the current state of space networking into an intelligent network of networks.

Rachel Mary Dudukovich↗
NASA NTRS2021

Model-Independent Time-Delay Interferometry Based on Principal Component Analysis

With a laser interferometric gravitational-wave detector in separate free flying spacecraft, the only way to achieve detection is to mitigate the dominant noise arising from the frequency fluctuations of the lasers via postprocessing. The noise can be effectively filtered out on the ground through a specific technique called time-delay interferometry (TDI), which relies on the measurements of time-delays between spacecraft and careful modeling of how laser noise enters the interferometric data. Recently, this technique has been recast into a matrix-based formalism by several authors, offering a different perspective on TDI, particularly by relating it to principal component analysis (PCA). In this work, we demonstrate that we can cancel laser frequency noise by directly applying PCA to a set of shifted data samples, without any prior knowledge of the relationship between single-link measurements and noise, nor time-delays. We show that this fully data-driven algorithm achieves a gravitational-wave sensitivity similar to classic TDI.

Quentin Baghi↗
NASA NTRSDate not supplied

Communication Delays, Disruptions, and Blackouts for Crewed Mars Missions

As NASA continues to develop the Moon2Mars campaign, there are a number of challenges that must be addressed to execute a successful crewed mission to Mars. One of those challenges is delays, disruptions, and blackouts that crew will experience during their mission to Mars, and that is the challenge evaluated in this paper. Our analysis showed that communication delays will vary from 0 to 22 minutes over the course of a mission, peaking while the crew is at or just departed from Mars. The disruptions occur in a similar time frame and can last for several days up to several months, depending on the solar disturbance sensitivity of the communication band being used. The delays and disruptions will have an impact on crewed Mars missions, and determining mitigations is future work to be informed by this analysis.

Katherine T McBrayer↗
NASA NTRS2023

Application of Fountain Code to High-Rate Delay Tolerant Networks

Space communication poses several unique challenges that are not always present in typical terrestrial communications. Currently, communication with satellites is based on point-to-point links, and development of an interplanetary internet is an active research area. Delay Tolerant Networking (DTN) has been proposed as a way to mitigate the long delays and disruptions found in deep space. A specialized version of DTN, called High-rate Delay Tolerant Networking (HDTN), has been developed by NASA to support a variety of missions requiring store-and-forward capability. However, there are still several features that are desired for HDTN including data fragmentation, multicast, and anycast. This project proposes the application of fountain code in HDTN as a means of fragmenting, distributing, and reassembling data (in the form of bundles) across multiple nodes (i.e. satellites) to any number of receivers (i.e. ground stations). Fountain code is shown to be a promising encoding method for use with the HDTN protocol suite due to its short runtimes, small encoded file sizes, and loss tolerance.

Noah Douglass↗
NASA NTRSDate not supplied

DeepONet-Assisted Optimization of Surface Topography for Transition Delay in a Mach 4.5 Boundary Layer

We use deep learning, an ensemble variational technique (EnVar), and direct numerical simulations(DNS) to design an optimal topography for a two-dimensional roughness element that delays the on-set of laminar-turbulent transition in a Mach 4.5 flat-plate boundary layer. Deep operator networks (DeepONets), which have the known ability to learn complex nonlinear operators within dynamical systems, are used for machine learning. For the baseline configuration of a smooth flat plate, the second-mode waves at the DNS inflow cause a quick nonlinear breakdown of the high-speed boundary layer within the computational domain. Results reported in the present study validate the ability of DeepONets to model the transition delay via a given topography of the roughness element. The computing cost to optimize the rough-ness element for minimal skin-friction drag is substantially lowered by the DeepONets-based reduced-order model. In comparison to the baseline method of EnVar optimization based on DNS alone, the DeepONets-based EnVar optimizer is able to delay transition past the outflow boundary of the computational domain while utilizing almost 5–6 times fewer DNS.

Machine Learning↗
NASA NTRS2024

4K High Definition Video and Audio Streaming Across High-rate Delay Tolerant Space Networks

Audio and video streaming across delay tolerant networks are relatively new phenomena. During the Apollo 11 mission, video and audio were streamed directly back to Earth using fully analog radios. This streaming capability atrophied over time due to the gradual conversion to digital electronics accompanied with higher resolutions causing the required bit rates to outpace communication link performance. Additionally, 21st century space systems face the new requirement of interconnectedness. Delay Tolerant Networking (DTN) attempts to solve this requirement by uniting traditional point to point links into a robust and dynamic network. However, In order to avoid system bottlenecks, the High-Rate Delay Tolerant Networking (HDTN) implementation focuses on performance-optimization of the standards. This work extends the functionality of HDTN by implementing audio and video streaming, with the goal of demonstrating the practical application of high definition media streaming across space networks. A series of network topologies were created including simple point to point links and multi-node multi-hop networks. Test media in the form of prerecorded and live footage was streamed across the network. A set of objective quality metrics were established in order to measure the stream quality. A lunar network was emulated using a mixture of embedded ARM platforms.

Kyle J Vernyi↗
DOE OSTI2025

Dynamics modeling of molten salt reactor with reduced and expanded representations of delayed neutron precursors

Molten salt reactors (MSRs) present unique challenges in dynamic behavior due to the mobility of their fuel. In these reactors, delayed neutron precursors (DNPs) drift with the fuel circulation through the primary loop. As a result, a fraction of DNPs decays outside the core, effectively reducing the available delayed neutron population for reactivity control. Consequently, precise modeling of the distribution and behavior of DNPs is critical for accurate reactor dynamics simulations. In this study, the System Dynamics Analysis Tool (SDAT) was used to simulate a thermal-spectrum MSR under steady-state conditions and following transients. The effects of using reduced and expanded representations of DNPs with fewer or more groups than the conventional 6-group model were investigated. Their impact on the simulated distribution of precursors in the primary loop, reactivity loss value, and reactor response to transients was analyzed. Simulation results showed that reduced models lead to the loss of the actual DNPs distribution data, resulting in less accurate estimates of reactivity loss. Reactor power predictions using these reduced models showed significant deviations compared to those using the conventional 6-group model in transient simulations. Expanded models offered a more accurate representation of the distribution of DNPs and reactivity loss estimates. Reactor power predictions using expanded models showed minimal deviation from the conventional 6-group model during the simulated transients.

analysis↗
DOE OSTI2024

H ∞ Control for Energy Dispatch in Autonomous Nanogrid With Communication Delays

This paper proposes an optimal controller and estimator for energy dispatch to balance the power supply and demand considering communication delays. The proposed algorithm involves modeling an autonomous nanogrid (ANG) consisting of distributed energy resources, energy storage systems, loads, an $H$ ∞ controller with a reference power modulation technique, and a state estimator. The ANG was developed to express the dynamic supply-demand energy balance of a nanogird system. Reference power modulation was designed to generate the desired ESS power based on the imbalanced energy. Random communication delays were modeled using a stochastic variable satisfying the Bernoulli random binary distribution. The optimal $H$ ∞ controller and estimator were developed using a linear matrix inequality approach to exponentially stabilize the closed-loop system. Simulations were performed using real daily demand forecasts obtained from the Korea Meteorological Administration to demonstrate the effectiveness of the proposed real-time optimization algorithm.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2006

Autonomous Congestion Control in Delay-Tolerant Networks

Congestion control is an important feature that directly affects network performance. Network congestion may cause loss of data or long delays. Although this problem has been studied extensively in the Internet, the solutions for Internet congestion control do not apply readily to challenged network environments such as Delay Tolerant Networks (DTN) where end-to-end connectivity may not exist continuously and latency can be high. In DTN, end-to-end rate control is not feasible. This calls for congestion control mechanisms where the decisions can be made autonomously with local information only. We use an economic pricing model and propose a rule-based congestion control mechanism where each router can autonomously decide on whether to accept a bundle (data) based on local information such as available storage and the value and risk of accepting the bundle (derived from historical statistics). Preliminary experimental results show that this congestion control mechanism can protect routers from resource depletion without loss of data.

delay-tolerant networking↗
NASA NTRS2005

Autonomous Congestion Control in Delay-Tolerant Networks

Congestion control is an important feature that directly affects network performance. Network congestion may cause loss of data or long delays. Although this problem has been studied extensively in the Internet, the solutions for Internet congestion control do not apply readily to challenged network environments such as Delay Tolerant Networks (DTN) where end-to-end connectivity may not exist continuously and latency can be high. In DTN, end-to-end rate control is not feasible. This calls for congestion control mechanisms where the decisions can be made autonomously with local information only. We use an economic pricing model and propose a rule-based congestion control mechanism where each router can autonomously decide on whether to accept a bundle (data) based on local information such as available storage and the value and risk of accepting the bundle (derived from historical statistics).

delay tolerant networking↗
NASA NTRS2014

Variable-Delay Polarization Modulators for Cryogenic Millimeter-Wave Applications

We describe the design, construction, and initial validation of the variable-delay polarization modulator (VPM) designed for the PIPER cosmic microwave background polarimeter. The VPM modulates between linear and circular polarization by introducing a variable phase delay between orthogonal linear polarizations. Each VPM has a diameter of 39 cm and is engineered to operate in a cryogenic environment (1.5 K). We describe the mechanical design and performance of the kinematic double-blade flexure and drive mechanism along with the construction of the high precision wire grid polarizers.

cryogenic environment↗
NASA NTRS2016

Transmission Scheduling and Routing Algorithms for Delay Tolerant Networks

The challenges of data processing, transmission scheduling and routing within a space network present a multi-criteria optimization problem. Long delays, intermittent connectivity, asymmetric data rates and potentially high error rates make traditional networking approaches unsuitable. The delay tolerant networking architecture and protocols attempt to mitigate many of these issues, yet transmission scheduling is largely manually configured and routes are determined by a static contact routing graph. A high level of variability exists among the requirements and environmental characteristics of different missions, some of which may allow for the use of more opportunistic routing methods. In all cases, resource allocation and constraints must be balanced with the optimization of data throughput and quality of service. Much work has been done researching routing techniques for terrestrial-based challenged networks in an attempt to optimize contact opportunities and resource usage. This paper examines several popular methods to determine their potential applicability to space networks.

Space Networking↗
NASA NTRS2016

Toward a Unified Routing Framework for Delay-Tolerant Networking

Routing in Delay-/Disruption-Tolerant Networking (DTN) has long been recognized as a challenging research topic. The difficulty lies in the fact that link intermittency and network partitioning, possibly coupled with long delays, prevent the use of Internet solutions based on an up-to-date comprehensive knowledge of network topology, as communicated by routing protocols. In the literature on DTN routing, there is a dichotomy between solutions designed for deterministic (e.g., space flight) networks, such as Contact Graph Routing (CGR), and the wide variety of protocols designed for opportunistic terrestrial networks. After a discussion of the origin and motivations of this duality, the paper presents an opportunistic extension of CGR (OCGR). The aim is to try to resolve the DTN routing dichotomy by providing a unified approach suitable for all DTN environments.

Routing↗
NASA NTRS2021

A Mathematical Analysis of an Example Delay Tolerant Network using the Theory of Sheaves

NASA’s High-Data Rate Architecture (HiDRA) project is working towards a general yet practical toolkit and knowledge base to help usher in the era of new technologies for space systems communications, such as optical links. The High-Rate Delay Tolerant Networking (HDTN) implementation falls under the umbrellas of both the toolkit and the knowledge base, as its advancements illuminate more general areas of Delay Tolerant Networking (DTN) that need growth. The goal of this paper is to explore the usage of particular mathematical machineries, namely temporal flow networks and sheaves, to identify fundamental, underlying structures in DTN for space systems. Satellites, space assets, ground stations, etc. give rise to a disconnected network, and it is the goal of DTN to glue disparate links together into a cohesive system, that is, a network. Depending on a given link, the latencies might be beyond that which the Transmission Control Protocol (TCP) can handle, and contact times might have one-way light times in excess of minute (sometimes significantly longer). Some links might be periodic (say, due to orbital mechanics) or they might not be. This diversity has made it difficult to probe the underlying structure. An immediate consequence is that DTNs in practice today are controlled by globally distributed contact plans (schedules), which are the input to the contact graph routing (CGR) algorithm. While this is effective for smaller networks, it will be very difficult to scale for future networks. Deeper and more rigorous theory is needed to bring DTN to the next evolutionary step. To this end, this paper introduces and suggests a mathematical framework for DTN, and applies it to a space network that is simulated using an orbital analysis toolkit. The tag-line for the structure known as sheaves is that they are the mathematically precise way of gluing local data together into unique, global data. If we consider routing, we see that networking is a “sheafy” science. We then discuss a simplified sheaf model, known as the cellular sheaf. The sheaf-theoretic analysis is presented and discussed, as it is hoped that this and related papers will help form the primordial ooze of DTN theory. Finally there is a section of future work suggesting follow-on research.

Delay Tolerant Networking↗
NASA NTRS2023

High-Rate Delay Tolerant Networking (HDTN) User Guide Version 1.0

Delay Tolerant Networking (DTN) has been identified as a key technology to enable and facilitate the development and growth of future space networks. Classically, space communications networks are collections of disparate links that are manually managed either point-to-point or use space relays. The accelerating accessibility of space enables a new scaling of space nodes, yet both the manual management of configurations and scheduling and the lack of structure connecting links precisely prohibit scaling. This challenge gives rise to newer and larger classes of communications needs that are met by DTN, which must overcome the disconnection, disruption, latency, and mobility featured in space communications systems. DTN joins the underlying links as an overlay, and can be made to communicate over any protocol stack. The core actions of DTN are store, carry, and forward, where data are stored instead of dropped if there is no immediately available outduct. It does this by taking the DTN unit of data, bundles, and providing necessary layers to adapt these bundles to the underlying transport protocols of choice; these are called convergence layers. DTN's Bundle Protocol (BP) can then be used on top of terrestrial protocol stacks, such as TCP/IP, as well as protocols for space, such as LTP/AOS, all in the same network. For emphasis it is noted that bundles can be of essentially any size, and hence this convergence to lower layers of choice is necessary. Existing DTN implementations have operated in constrained environments with limited resources, resulting in low data speeds. However, as various technologies have advanced, data transfer rates and efficiency have advanced, which has pushed the need for a DTN implementation for ground systems and for spacecraft that is performance-oriented in order to not impose an unnecessary bottleneck. High-rate Delay Tolerant Networking (HDTN) takes advantage of modern hardware platforms to substantially reduce latency and improve throughput compared to today’s DTN operations. The HDTN implementation maintains interoperability with existing deployments of DTN that conform to IETF RFCs 4838, 5050, and 9171. At the same time, HDTN defines a new data format better suited to higher-rate operation. It defines and adopts a massively parallel pipelined and message-oriented architecture, allowing the system to scale gracefully as its resources increase. HDTN’s architecture also supports hooks to replace various processing pipeline elements with specialized hardware accelerators. This offers improved Size, Weight, and Power (SWaP) characteristics while reducing development complexity and cost.

Delay Tolerant Networking↗