Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Mechanical behavior and microstructure of Ti{sub 20}Hf{sub 20}Zr{sub 20}Ta{sub 20}Nb{sub 20} high-entropy alloy loaded under quasi-static and dynamic compression conditions

The microstructure and the mechanical behavior of equimolar Ti{sub 20}Hf{sub 20}Zr{sub 20}Ta{sub 20}Nb{sub 20} high-entropy alloy in a wide range of initial strain rates between ~ 10{sup −3} s{sup −1} and ~ 3.4 × 10{sup 3} s{sup −1} were studied. A significant increment in the yield strength with increasing strain rate was observed. The yield strength at ~ 3.4 × 10{sup 3} s{sup −1} was about 40% higher than that measured at ~ 10{sup −3} s{sup −1}. Analysis by electron backscatter diffraction shows that in the low strain rate regime (up to ~ 10 s{sup −1}) the deformation occurs mainly in evenly distributed bands, while in the dynamic regime the deformation is strongly localized in macroscopic shear bands accompanied by softening even after the onset of yielding. The Kernel Average Misorientation technique reveals a high level of lattice rotation within these bands that also carries intense shear. In addition, X-ray diffraction line profile analysis indicates that the sharp increase in the flow stress is mostly related to an increase of the dislocation density. - Highlights: • Strain rate effect on the plastic behavior of Ti{sub 20}Hf{sub 20}Zr{sub 20}Ta{sub 20}Nb{sub 20} HEA was studied. • Low strain rate regime was characterized by a continuous hardening. • At high strain rates softening occurred shortly after the onset of yielding. • Intense strain localization in shear bands occurred in the high strain rate regime. • High dislocation density explained the upturn of flow stress at high strain rates.

36 MATERIALS SCIENCE↗

Characterization of electrically-active defects in ultraviolet light-emitting diodes with laser-based failure analysis techniques

Laser-based failure analysis techniques demonstrate the ability to quickly and non-intrusively screen deep ultraviolet light-emitting diodes (LEDs) for electrically-active defects. In particular, two laser-based techniques, light-induced voltage alteration and thermally-induced voltage alteration, generate applied voltage maps (AVMs) that provide information on electrically-active defect behavior including turn-on bias, density, and spatial location. Here, multiple commercial LEDs were examined and found to have dark defect signals in the AVM indicating a site of reduced resistance or leakage through the diode. The existence of the dark defect signals in the AVM correlates strongly with an increased forward-bias leakage current. This increased leakage is not present in devices without AVM signals. Transmission electron microscopy analysis of a dark defect signal site revealed a dislocation cluster through the pn junction. The cluster included an open core dislocation. Even though LEDs with few dark AVM defect signals did not correlate strongly with power loss, direct association between increased open core dislocation densities and reduced LED device performance has been presented elsewhere [M. W. Moseley et al., J. Appl. Phys. 117, 095301 (2015)].

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

X-ray Characterisation of Zinc Oxide (ZnO) Single Crystal Substrates

Single crystal substrates of low defect density are paramount for fully realizing the numerous applications of zinc oxide (ZnO) wide bandgap semiconductors. While ZnO substrates are commercially available from various vendors, very little information is available on the structural properties of these substrates. Therefore, an extensive evaluation of available substrates would serve as a basis for the development of ZnO based devices and technologies. In this study, bulk ZnO single crystal substrates grown by different growth techniques have been characterised using synchrotron white beam X-ray topography and high resolution X-ray diffraction. The substrates exhibit a wide range of dislocation densities from as high as 10{sup 6} cm{sup -2} down to less than 1000 cm{sup -2} depending on the growth technique employed. The authors evaluation reveals that ZnO crystals grown by the hydrothermal technique possess the best structural quality with dislocation densities of 800-1000 cm{sup -2} and rocking curves with a full width half maximum of less than 12 arc seconds.

36 MATERIALS SCIENCE↗

Microstructural and material property changes in severely deformed Eurofer-97

Severe plastic deformation changes the microstructure and properties of steels, which may be favourable for their use in structural components of nuclear reactors. In this study, high-pressure torsion (HPT) was used to refine the grain structure of Eurofer-97, a ferritic/martensitic steel. Electron microscopy and X-ray diffraction were used to characterise the microstructural changes. Following HPT at room temperature to a maximum shear strain of 230, the average grain size reduced by a factor of ~30, with a marked increase in high-angle grain boundaries. Dislocation density also increased by more than one order of magnitude. The thermal stability of the deformed material was investigated via in-situ annealing during synchrotron X-ray diffraction. This revealed substantial recovery between 450 K – 800 K. Irradiation with 20 MeV Fe-ions to ~0.1 dpa caused a 20% reduction in dislocation density compared to the as-deformed material. However, HPT deformation prior to irradiation only had a minor effect in mitigating the irradiation-induced reductions in thermal diffusivity and surface acoustic wave velocity of the material. Microstructural and material property changes are dominated by deformation compared to irradiation. In light of this, the benefits of using HPT to improve the irradiation resistance of Eurofer-97 are limited. These results provide a multi-faceted view of the changes in ferritic/martensitic steels due to severe plastic deformation, and how these changes can be used to alter material properties.

ion-irradiation↗

Study of Ferrite During Refinement of Prior Austenite Grains in Microalloyed Steel Continuous Casting

The formation of coarse prior austenite grain is a key factor to promote transverse crack, and the susceptibility to the transverse crack can be reduced by refining the austenite grain size. In the present study, the high-temperature confocal laser scanning microscope (CLSM) was used to simulate two types of double phase-transformation technologies. The distribution and morphology of ferrites under different cooling conditions were analyzed, and the effects of ferrite distribution and morphology on the double phase-transformation technologies were explored to obtain the suitable double phase-change technology for the continuous casting process. The results indicate that, under the thermal cycle TH0 [the specimens were cooled down to 913 K (640 °C) at a cooling rate of 5.0 K/s (5.0 °C/s)], the width of prior austenite grain boundaries was thick, and the dislocation density at grain boundaries was high. It had strong inhibition effect on crack propagation; under the thermal cycle TH1 [the specimens were cooled down to 1073 K (800 °C) at a cooling rate of 5.0 K/s (5.0 °C/s) and then to 913 K (640 °C) at a cooling rate of 1.0 K/s (1.0 °C/s)], the width of prior austenite grain boundary was thin, and the dislocation density at grain boundaries was low. It was beneficial to crack propagation. After the first phase change, the developed film-like ferrite along the austenite grain boundaries improved the nucleation conditions of new austenitic grains and removed the inhibition effect of the prior austenite grain boundaries on the austenite grain size.

36 MATERIALS SCIENCE↗

Deformation behavior of HCP titanium alloy: Experiment and Crystal plasticity modeling

The deformation behavior of commercially pure titanium is studied using experiments and a crystal plasticity model. Compression tests along the rolling, transverse, and normal-directions, and tensile tests along the rolling and transverse directions are performed at room temperature to study the activation of slip and twinning in the hexagonal closed packed titanium. A detailed EBSD based statistical analysis of the microstructure is performed to develop statistics of both {10-12} tensile and {11-22} compression twins. A simple Monte Carlo (MC) twin variant selection criterion is proposed within the framework of the visco-plastic self-consistent (VPSC) model with a dislocation density (DD) based law used to describe dislocation hardening. In the model, plasticity is accommodated by prismatic, basal and pyramidal slip modes, and {10-12} tensile and {11-22} compression twinning modes. Thus, the VPSC-MC model successfully captures the experimentally observed activation of low Schmid factor twin variants for both tensile and compression twins modes. The model also predicts macroscopic stress-strain response, texture evolution and twin volume fraction that are in agreement with experimental observations.

36 MATERIALS SCIENCE↗

In-situ study of rules of nanostructure evolution, severe plastic deformations, and friction under high pressure

Severe plastic deformations under high pressure are used to produce nanostructured materials but were studied ex-situ. Rough diamond anvils are introduced to reach maximum friction equal to yield strength in shear and the first in-situ study of the evolution of the pressure-dependent yield strength and radial distribution of nanostructural parameters are performed for severely pre-deformed Zr. ω-Zr behaves like perfectly plastic, isotropic, and strain-path-independent and reaches steady values of the crystallite size and dislocation density, which are pressure-, strain- and strain-path-independent. However, steady states for a-Zr obtained with smooth and rough anvils are different, causing major challenge in plasticity theory. In-situ study of severe plastic deformation of α-Zr with rough diamond anvils revealed that pressure-dependent yield strength, crystallite size, and dislocation density are getting steady and plastic strain- and strain-path-independent.

36 MATERIALS SCIENCE↗

Deep levels in as-grown and electron-irradiated n-type GaN studied by deep level transient spectroscopy and minority carrier transient spectroscopy

Development of high performance GaN-based devices is strongly dependent on the possibility to control and understand defects in material. Important information about deep level defects is obtained by deep level transient spectroscopy and minority carrier transient spectroscopy on as-grown and electron irradiated n-type bulk GaN with low threading dislocation density produced by halide vapor phase epitaxy. One hole trap labelled H1 (E{sub V} + 0.34 eV) has been detected on as-grown GaN sample. After 2 MeV electron irradiation, the concentration of H1 increases and at fluences higher than 5 × 10{sup 14 }cm{sup −2}, a second hole trap labelled H2 is observed. Simultaneously, the concentration of two electron traps, labelled T1 (E{sub C} – 0.12 eV) and T2 (E{sub C} – 0.23 eV), increases. By studying the increase of the defect concentration versus electron irradiation fluence, the introduction rate of T1 and T2 using 2 MeV- electrons was determined to be 7 × 10{sup −3 }cm{sup −1} and 0.9 cm{sup −1}, respectively. Due to the low introduction rate of T1, it is suggested that the defect is associated with a complex. The high introduction rate of trap H1 and T2 suggests that the defects are associated with primary intrinsic defects or complexes. Some deep levels previously observed in irradiated GaN layers with higher threading dislocation densities are not detected in present investigation. It is therefore suggested that the absent traps may be related to primary defects segregated around dislocations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Heat Treatment and Combination of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Titanium Alloy Ti6Al2V2Zr1.5Mo

The heat treatment and cold rolling combinations have been carried out on titanium alloy Ti6Al2V2Zr1.5Mo, and microstructure evolution and mechanical behavior have been studied. Solution treatment below the β-transus temperature, followed by air cooling, resulted in higher microhardness/strength as compared to the same with water quenching. A sudden drop in microhardness/strength is observed in sample solution heat-treated above β-transus temperature followed by air cooling. The former is attributed to the additional presence of fine secondary α-phase formed by dynamic aging during air cooling as compared to water-quenched samples which did not have fine secondary α-phase. Solution treatment above β-transus temperature resulted in Widmanstatten microstructure with no significant fine secondary α in air-cooled samples. Among the studied conditions of cold rolling (CR), gain in strength of the alloy from annealed condition is significant with first 15% reduction and thereafter it is marginal for 30% reduction. Initiation of cracks at the edges has been observed in 30% CR. The microstructure of cold-rolled samples confirms the fragmentation of α-plates with the presence of high dislocation density. Heat treatment of cold-rolled samples resulted in significant reduction in strength from the as-cold-rolled conditions. The marginally lower strength than the as-received (annealed) or heat-treated alloy samples is due to the recrystallization in CR samples and the formation of Widmanstatten microstructure in air-cooled samples. The alloy does not have fine secondary α or regions with large dislocation density in this condition. The microstructure in the samples heat-treated (with air cooling) below as well as above β-transus temperature (after CR) is similar to air-cooled samples (without prior CR) with heat treatment above β-transus temperature. This indicates the reduction in recrystallization temperature with cold working, which is substantiated with the reduction in strength as well.

36 MATERIALS SCIENCE↗

Strain induced grain boundary migration effects on grain growth of an austenitic stainless steel during static and metadynamic recrystallization

Static and metadynamic recrystallization of an AISI 304L austenitic stainless steel was investigated at 1100 °C and 10{sup −} {sup 2} s{sup −} {sup 1} strain rate. The kinetics of recrystallization was determined through double hit compression tests. Two strain levels were selected for the first compression hit: ε{sub f} = 0.15 for static recrystallization (SRX) and 0.25 for metadynamic recrystallization (MDRX). Both the as-deformed and the recrystallized microstructures were investigated through optical microscopy and electron back-scattered diffraction (EBSD) technique. During deformation, strain induced grain boundary migration appeared to be significant, producing a square-like grain boundary structure aligned along the directions of the maximum shear stresses in compression. EBSD analysis revealed to be as a fundamental technique that the dislocation density was distributed heterogeneously in the deformed grains. Grain growth driven by surface energy reduction was also investigated, finding that it was too slow to explain the experimental data. Based on microstructural results, it was concluded that saturation of the nucleation sites occurred in the first stages of recrystallization, while grain growth driven by strain induced grain boundary migration (SIGBM) dominated the subsequent stages. - Highlights: • Recrystallization behavior of a stainless steel was investigated at 1100 °C. • EBSD revealed that the dislocation density distribution was heterogeneous during deformation. • Saturation of nucleation sites occurred in the first stages of recrystallization. • Strain induced grain boundary migration (SIGBM) effects were significant. • Grain growth driven by SIGBM dominated the subsequent stages.

36 MATERIALS SCIENCE↗

Microstructure and high temperature tensile properties of 316L fabricated by laser powder-bed fusion

316L stainless steel fabricated by laser powder-bed fusion (LPBF) has attracted significant attention due to a unique combination of strength and ductility at room temperature. Understanding of high temperature tensile properties of LPBF fabricated 316L is, however, limited. In the present investigation, tensile testing was conducted at 20–700ºC on LPBF 316L in as printed condition and after annealing for 5 h at 500–800ºC. Room temperature data confirmed the excellent ductility of the LPBF-processed 316L steel due to the cellular structure with high dislocation density. However, a significant decrease in ductility was observed at temperatures above 200ºC. These results are consistent with a change of deformation mechanisms observed in wrought 316L, with twinning playing a key role at room temperature. Finally, microstructure characterization and tensile testing revealed that the cellular structure is stable up to 500ºC, but a decrease of yield strength was observed at temperatures above 600ºC likely due to a decrease in dislocation density via annealing.

36 MATERIALS SCIENCE↗

Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment

The selective laser melting of high temperature alloys is of great interest to the aerospace industry as it offers the prospect of producing more complex geometries than can be achieved with other manufacturing methods. In this study, the microstructure of the nickel-based superalloy, CM247LC, has been characterised following selective laser melting and after a post deposition heat treatment below the γ′ solvus temperature. In the as-deposited state, scanning electron microscopy with electron backscatter diffraction revealed a fine, cellular microstructure with preferential alignment of 〈001〉 along the build direction. A high dislocation density was seen at the periphery of the cells, indicating substantial localised deformation of the material. Fine primary MC carbides were also observed in the inter-cellular regions. High-resolution transmission electron microscopy identified the occurrence of very fine γ′ precipitates, approximately 5 nm in diameter, dispersed within the gamma phase. After heat treatment, the elongated cell colonies were observed to partially coalesce, accompanied by a decrease in dislocation density, producing columnar grains along the build direction. Cuboidal γ′ precipitates approximately 500 nm in diameter were observed to form in the recrystallised grains, accompanied by larger γ′ precipitates on the grain boundaries.

36 MATERIALS SCIENCE↗

The effect of thermomechanical treatment and tempering on the subsurface microstructure and bendability of direct-quenched low-carbon strip steel

Highlights: • Surface properties mainly determine the bendability of high strength steel. • Tempering improves bendability by softening the microstructure. • Surface texture is affected by thermomechanical treatment but not by tempering. • Strong shear texture component and upper bainite are detrimental to bendability. - Abstract: Recent results in the literature have shown that subsurface properties play a key role during the bending of steel plates. Now, for the first time, surface microstructure, surface texture, subsurface hardness and dislocation density have been studied to reveal the effect of tempering and thermomechanical treatment on the bendability of a direct-quenched strip steel. In the experiments, different thermomechanical treatments as well as non-isothermal tempering treatments were performed with slow heating to 570 °C and slow cooling to simulate the tempering of large steel coils in a batch annealing furnace. The results show that in addition to the improved production efficiency obtained through direct quenching and a single tempering process, tempering improves bendability by reducing subsurface dislocation density and hardness without a significant loss of strip yield strength. The subsurface microstructure and texture of the strip are the result of thermo-mechanical processing and transformation behaviour. Upper bainite containing elongated Martensite-Austenite (MA) islands in addition to an intense shear texture component {112}<111>{sub α} leads to shear band formation, and therefore poorer bendability when the bend axis is perpendicular to the rolling direction. This texture is not affected by tempering. Therefore, tempering does not improve the bendability of steels with an unfavourable texture. When the subsurface layers comprise a softer ferritic microstructure, good bendability is obtained in the untempered direct-quenched condition with a modest improvement caused by tempering.

36 MATERIALS SCIENCE↗

Structural Analysis of ZnO Nanoparticles Reinforced P(3HB-co-15 mol% 3HHx) Bioplastic Composite

Bioplastics are gaining interest due to their biodegradable and biocompatible nature which can be used as a replacement for petroleum based plastics. Poly (3-hydroxybutyrate-co-15 mol% 3-hydroxyhexanoate) [P(3HB-co-15 mol% 3HHx)]/ZnO nanoparticles (NPs) blended bioplastic films were fabricated by solution casting method using chloroform as solvent. The structural characteristics such as peak intensity analysis, crystallite size, dislocation density, and texture coefficient of ZnO NPs mixed P(3HB-co-15 mol% 3HHx) samples were studied using X-Ray Diffraction (XRD) and Fourier Transform Infra-Red (FTIR) analyses. It is clear from the XRD analyses that the crystallinity of P(3HB-co-15 mol% 3HHx) was decreased considerably as ZnO NPs concentration increased. The crystallite size of P(3HB-co-15 mol% 3HHx) was decreased with an increase in ZnO NPs concentration and observed within 150 nm and the dislocation density was decreased with respect to the orientation of P(3HB-co-15 mol% 3HHx) crystals. Simultaneously, the structural properties of ZnO NPs in P(3HB-co-15 mol% 3HHx) matrix were affected noticeably with respect to the ZnO NPs and copolymer concentrations. The characteristic peak positions from FTIR spectra of P(3HB-co-15 mol% 3HHx) copolymer shifted towards higher frequency and evidenced the existence of structural defects. Overall, it was found from both XRD and FTIR analyses that the presence of ZnO NPs affected the crystallinity of P(3HB-co-15 mol% 3HHx) copolymer due to the formation of intermolecular bonds, which restricted the preferential orientation of P(3HB-co-15 mol% 3HHx) molecules which was observed from the texture coefficient analyses. Based on these observations, ZnO NPs at low concentrations can be used with P(3HB-co-15 mol% 3HHx) copolymer effectively and the resulting composite may be used for packaging application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Coincident site lattice-matched InGaN on (111) spinel substrates

Coincident site lattice-matched wurtzite (0001) In{sub 0.31}Ga{sub 0.69}N, emitting in the important green wavelength region, is demonstrated by molecular beam epitaxy on a cubic (111) MgAl{sub 2}O{sub 4} spinel substrate. The coincident site lattice matching condition involves a 30 deg. rotation between the lattice of the InGaN epitaxial layer and the lattice of the spinel. This work describes an alternative approach towards realizing more compositionally homogenous InGaN films with low dislocation density emitting in the ''green gap'' of low efficiency currently observed for semiconductor light emitting diodes (LEDs). This approach could lead to higher efficiency green LEDs presently of great interest for solid-state lighting applications.

36 MATERIALS SCIENCE↗

Electrical, luminescent, and deep trap properties of Si doped n-GaN grown by pendeo epitaxy

Electrical and luminescent properties and deep trap spectra of Si doped GaN films grown by maskless epitaxial lateral overgrowth (MELO) are reported. The dislocation density in the wing region of the structure was 10{sup 6 }cm{sup −2}, while in the seed region it was 10{sup 8 }cm{sup −2}. The major electron traps present had activation energy of 0.56 eV and concentrations in the high 10{sup 15 }cm{sup −3} range. A comparison of diffusion length values and 0.56 eV trap concentration in MELO GaN and epitaxial lateral overgrowth (ELOG) GaN showed a good correlation, suggesting these traps could be effective in carrier recombination. The doped MELO films were more uniform in their electrical properties than either ELOG films or undoped MELO films. We also discuss the differences in deep trap spectra and luminescence spectra of low-dislocation-density MELO, ELOG, and bulk n-GaN samples grown by hydride vapor phase epitaxy. It is suggested that the observed differences could be caused by the differences in oxygen and carbon contamination levels.

36 MATERIALS SCIENCE↗

Effects of different annealing atmospheres on the properties of cadmium sulfide thin films

Graphical abstract: The effects of different annealing atmospheres (air and sulfur) on the structural, morphological and optical properties of CdS thin films were studied at three different pH values. - Highlights: • Compactness and smoothness of the films were enhanced after sulfur annealing. • Micro-strain values of some films were improved after sulfur annealing. • Dislocation density values of some films were improved after sulfur annealing. • Band gap values of the films were improved after sulfur annealing. - Abstract: Cadmium sulfide (CdS) thin films were prepared on glass substrates by using chemical bath deposition (CBD) technique. The effects of different annealing atmospheres (air and sulfur) on the structural, morphological and optical properties of CdS thin films were studied at three different pH values. Compactness and smoothness of the films (especially for pH 10.5 and 11) enhanced after sulfur annealing. pH value of the precursor solution remarkably affected the roughness, uniformity and particle sizes of the films. Based on the analysis of X-ray diffraction (XRD) patterns of the films, micro-strain and dislocation density values of the sulfur-annealed films (pH 10.5 and 11) were found to be lower than those of air-annealed films. Air-annealed films (pH 10.5, 11 and 11.5) exhibited higher transmittance than sulfur-annealed films in the wavelength region of 550–800 nm. Optical band gap values of the films were found between 2.31 eV and 2.36 eV.

36 MATERIALS SCIENCE↗

Inverted metamorphic GaInAs solar cell grown by dynamic hydride vapor phase epitaxy

We present an inverted metamorphic rear heterojunction ~1.0 eV GaInAs solar cell deposited by dynamic hydride vapor phase epitaxy (D-HVPE) with high growth rate. This device uses a Ga 1-x In x P compositionally graded buffer (CGB) to bridge the lattice constant gap between the GaAs substrate and the Ga0.71In0.29As emitter layer. High-resolution x-ray diffraction and transmission electron microscopy confirm that the Ga 0.71 In 0.29 As emitter is grown lattice-matched to the in-plane lattice constant of the CGB with minimal generation of defects at the GaInAs/GaInP interface. The device contains a threading dislocation density of 2.3 × 10 6 cm -2 , a level that enables high-performance minority carrier devices and is comparable to previously demonstrated GaInP CGBs grown by D-HVPE. The device exhibits an open-circuit voltage of 0.589 V under a one-sun AM1.5G illumination condition and a bandgap-voltage offset of 0.407 V, indicating metamorphic epitaxial performance nearly equal to state-of-the-art devices. We analyze the dark current of the device and determine that reducing recombination in the depletion region, which can be achieved by reducing the threading dislocation density and optimizing the device doping density, will improve the device performance. Furthermore, the CGB and device layers, comprising ~8 µm of thickness, are grown in under 10 min, highlighting the ability of D-HVPE to produce high-quality metamorphic devices of all types with the potential for dramatically higher throughput compared to present technology.

14 SOLAR ENERGY↗