SEARCH · Search NASA
Results for “engineered matrix”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Crack width control and mechanical properties of low carbon engineered cementitious composites (ECC)
Engineered Cementitious Composites (ECC) have superior properties with high tensile ductility and tight crack width compared to conventional concrete. The properties of ECC are significantly influenced by the material composition which can be tailored to enhance the sustainability of ECC. Towards this goal, recycled crumb rubber (CR) and silica fume (SF) were used to tailor the properties of a polypropylene-fiber reinforced ECC with a low carbon binder based on limestone calcined clay cement (LC3) in this study. Crumb rubber was found to be effective in enhancing strain-hardening performance and reducing the width of the multiple microcracks. However, a loss of compressive strength was accompanied by an increasing amount of CR. While silica fume or lower w/b ratio enhanced the compressive strength, the crack width of ECC increased at higher SF content or lower w/b. The underlying mechanisms of these trends were traced to the alteration of the matrix fracture toughness and fiber/matrix interfacial bond. Rubber particle bridging was found to contribute to crack width control. Finally, the combined use of the LC3 green binder and CR led to a lowering of the embodied and operational carbon footprint of ECC.
Engineering Curcumin Biosynthesis in Poplar Affects Lignification and Biomass Yield
Lignocellulosic biomass is recalcitrant toward deconstruction into simple sugars mainly due to the presence of lignin. By engineering plants to partially replace traditional lignin monomers with alternative ones, lignin degradability and extractability can be enhanced. Previously, the alternative monomer curcumin has been successfully produced and incorporated into lignified cell walls of Arabidopsis by the heterologous expression of DIKETIDE-CoA SYNTHASE (DCS) and CURCUMIN SYNTHASE2 (CURS2). The resulting transgenic plants did not suffer from yield penalties and had an increased saccharification yield after alkaline pretreatment. Here, we translated this strategy into the bio-energy crop poplar. Via the heterologous expression of DCS and CURS2 under the control of the secondary cell wall CELLULOSE SYNTHASE A8-B promoter (ProCesA8-B), curcumin was also produced and incorporated into the lignified cell walls of poplar. ProCesA8-B:DCS_CURS2 transgenic poplars, however, suffered from shoot-tip necrosis and yield penalties. Compared to that of the wild-type (WT), the wood of transgenic poplars had 21% less cellulose, 28% more matrix polysaccharides, 23% more lignin and a significantly altered lignin composition. More specifically, ProCesA8-B:DCS_CURS2 lignin had a reduced syringyl/guaiacyl unit (S/G) ratio, an increased frequency of p-hydroxyphenyl (H) units, a decreased frequency of p-hydroxybenzoates and a higher fraction of phenylcoumaran units. Without, or with alkaline or hot water pretreatment, the saccharification efficiency of the transgenic lines was equal to that of the WT. These differences in (growth) phenotype illustrate that translational research in crops is essential to assess the value of an engineering strategy for applications. Further fine-tuning of this research strategy (e.g., by using more specific promoters or by translating this strategy to other crops such as maize) might lead to transgenic bio-energy crops with cell walls more amenable to deconstruction without settling in yield.
A review of low-rank methods for time-dependent kinetic simulations
Time-dependent kinetic models are ubiquitous in computational science and engineering. The underlying integro-differential equations in these models are high-dimensional, comprised of a six–dimensional phase space, making simulations of such phenomena extremely expensive. In this article we demonstrate that in many situations, the solution to kinetics problems lives on a low dimensional manifold that can be described by a low-rank matrix or tensor approximation. We then review the recent development of so-called low-rank methods that evolve the solution on this manifold. The two classes of methods we review are the dynamical low-rank (DLR) method, which derives differential equations for the low-rank factors, and a Step-and-Truncate (SAT) approach, which projects the solution onto the low-rank representation after each time step. Thorough discussions of time integrators, tensor decompositions, and method properties such as structure preservation and computational efficiency are included. We further show examples of low-rank methods as applied to particle transport and plasma dynamics.
Epitaxial strain tuning of Er 3+ in ferroelectric thin films
Er 3+ color centers are promising candidates for quantum science and technology due to their long electron and nuclear spin coherence times, as well as their desirable emission wavelength. By selecting host materials with suitable, controllable properties, we introduce new parameters that can be used to tailor the Er 3+ emission spectrum. PbTiO 3 is a well-studied ferroelectric material with known methods of engineering different domain configurations through epitaxial strain. By distorting the structure of Er 3+ -doped PbTiO 3 thin films, we can manipulate the crystal fields around the Er 3+ dopant. This is resolved through changes in the Er 3+ resonant fluorescence spectra, tying the optical properties of the defect directly to the domain configurations of the ferroelectic matrix. Additionally, we are able to resolve a second set of peaks for films with in-plane ferroelectric polarization. We hypothesize these results to be due to either the Er 3+ substituting different sites of the PbTiO 3 crystal, differences in charges between the Er 3+ dopant and the original substituent ion, or selection rules. Systematically studying the relationship between the Er 3+ emission and the epitaxial strain of the ferroelectric matrix lays the pathway for future optical studies of spin manipulation by altering ferroelectric order parameters.
Ultra-wideband mutual coupling compensation of active electronically scanned arrays in multi-channel radar systems
Technologies pertaining to the calibration of ultra-wide-band active-electronically-scanned arrays to compensate for transmit and receive mutual coupling between array elements and/or non-ideal isolated channels are described herein. A plurality of near-field measurements are taken by way of probe or probes that may be moved among a plurality of positions aligned with respective elements in the array. For each position of the probe, each of the elements of the array is stimulated to transmit or receive a calibration signal to or from the probe, respectively. Frequency-domain transfer functions are computed from the received signals by the probe or the element for each of the array elements in each of the positions of the probe. The inverse of the matrix of transfer functions comprise frequency-domain transmit and receive correction factors that are used to modify desired array inputs/outputs such that the modified signals correct for mutual coupling between elements in the array.
FEED Study of CarbonCapture Inc DAC and CarbonCure Utilization Technologies Using United States Steel’s Gary Works Plant Waste Heat (Final Report)
The University of Illinois at Urbana-Champaign (UIUC) led this project to produce a front-end engineering design (FEED) study of an advanced Direct Air Capture and Utilization System (DACUS) system that can remove a minimum of 5,000 tonnes/yr net of carbon dioxide from air (based on cradle-to-gate LCA) and utilizing the CO 2 to produce low carbon intensity ready mix concrete. The designed system, if built, would be larger than any currently existing Direct Air Capture (DAC) collector in the U.S. Such carbon capture technologies are critical to meeting the goals of the DOE’s program to accelerate climate-critical technology. In addition to the power sector, industrial facilities for the manufacture of steel and cement/concrete are among the major sources of anthropogenic CO 2 . DAC is a promising new technology for reducing CO 2 , a potent greenhouse gas, in the atmosphere but is expensive, in part due to the energy required to adsorb and desorb captured CO 2 during cycles. By integrating CarbonCapture Inc. (CCI) DAC modules at United States Steel's Gary Works (USS) and utilizing the site's waste heat, energy, and location this project evaluates the feasibility of utilizing the captured CO 2 and the logistics of transportation. CarbonCapture Inc. has developed an innovative DAC system using novel adsorbents to cost-effectively capture CO 2 . The captured, liquified gas will be trucked to ready-mix concrete plants within the region, the closest of which is approximately 3.5 miles away, where CarbonCure will inject it into concrete during the mixing process at the facilities. The carbon dioxide reacts with concrete, mineralizing into calcium carbonate (CaCO 3 ), permanently locking the greenhouse gas into the matrix of the building material. This FEED study demonstrated a full CO 2 value chain for DACUS from industrial facilities. It also provided a means for Visage Energy Corp. (Visage) to assess the impact of this holistic approach on job creation, regional economic impact, and environmental justice. The project team also included Sargent & Lundy (S&L) to provide the constructability review and costing of the integration of the DAC with the steel plant. Ecotek Engineering USA, LLC designed the outside battery limit (OSBL) infrastructure to connect the DAC and the plant. Activities performed during the project included: (1) Project Management Plan; (2) Technology Maturation Plan (TMP); (3) Initial Workforce Readiness Plan; (4) Workforce Readiness Plan; (5) Front-End Engineering Design (FEED) Study; (6) Project Design Basis; (7) Hazards and Operability (HAZOP) Study; (8) Constructability Review; (9) Project Cost Assessment; (10) Logistics Analysis of CO 2 Transportation to the Utilization Site; (11) Business Case Analysis; (12) Life Cycle Analysis (LCA); (13) Environmental Health and Safety (EH&S) Analysis; (14) Environmental Justice Analysis; and (15) Economic Revitalization and Job Creation Outcomes Analysis. This report provides a summary of the outcomes and results of the project, which was performed between Oct. 1, 2022, through Sept. 30, 2024.
Web-based wide-area monitoring platform for ringdown and clustering analytics in power systems
This paper introduces an open-source research platform for monitoring the Mexican interconnected power grid, allowing real-time processing and information extraction of the grid’s dynamic condition. Moreover, the platform is a Python-based development that embeds different ringdown and clustering analytics tools. In the case of ringdown analysis, the modal information can be extracted using some of the most known algorithms, i.e., Prony analysis, eigensystem realization algorithm (ERA), and matrix pencil (MP). For clustering analysis, the coherent behaviour of generator and non-generator buses is provided by applying recent state-of-the-art techniques such as affinity propagation, K-means, hierarchical agglomerative clustering, and typicality data analysis. The results of up to 93 PMUs show that this open-source platform suits researchers’ and engineers’ power system dynamic analysis requirements.
Synergic grain boundary segregation and precipitation in W- and W-Mo-containing high-entropy borides
The structures of W- and W-Mo-containing high-entropy borides (HEBs) are systematically studied by combining atomic-resolution transmission electron microscopy imaging, electron diffraction, and chemical analysis. Here, we reveal that W or W-Mo addition in HEBs leads to segregation of these elements to the grain boundaries (GBs). In the meantime, W- or W-Mo-rich precipitates also form along the GBs. Crystallographic analysis and atomic-scale imaging show that the GB precipitates in both W- and W-Mo-containing HEBs have a cube-on-cube orientation relationship with the matrix. With further strain analysis, the coherency of the precipitate/matrix interface is validated. Nanoindentation tests show that the simultaneous GB segregation and coherent precipitation, as a supplement to the grain hardening, provide additional hardening of the HEBs. Our work provides an in-depth understanding of the GB segregation and precipitation behaviors of HEBs. It suggests that GB engineering could be potentially used for optimizing the performance of high-entropy ceramics.
Code and Solution Verification Assessment of the CTF Thermal Hydraulic Subchannel Code
CTF is a thermal-hydraulics subchannel code jointly developed by Oak Ridge National Laboratory and North Carolina State University. Over the past seven years, the Consortium for Advanced Simulation of Light Water Reactors (CASL) has made a significant investment in developing CTF so it can be used to model light water reactors, including nominal operating conditions, departure from nucleate boiling analysis, and transients ranging from loss of flow to reactivity insertion accidents. In addition to implementing new modeling capabilities and developing the user input and output interface, extensive work has been performed to improve the code’s quality assurance program, resulting in a development process that conforms with NQA-1 requirements. The CASL program follows the Predictive Capability Maturity Model (PCMM) approach for assessing code quality, which emphasizes performing code verification(ensuring the code converges to the correct answer) and solution verification (ensuring the code converges for the intended application). Code and solution verification are used to identify uncertainty errors introduced by numerical approximations in the code and are important for demonstrating that the model is coded without error, which is an important aspect of the Best Estimate plus Uncertainty method. This paper presents a comprehensive overview of the code and solution verification testing that has been performed on CTF. A top-down approach is taken in which the intended CTF applications are presented, followed by the code features required for their modeling. These features are then linked to the applicable code and solution verification tests that demonstrate proper functioning. Past testing efforts are summarized, and new tests are added to help close gaps in the presented test matrix. Rather than performing “one-off” exercises, these tests are added to the automated CTF regression test suite to ensure continual code quality.
Low-Cost, High-Performance Carbon Fiber for Compressed Natural Gas Storage Tanks (Final Technical Report – Down Select Report)
The aim of this project is to reduce the cost of Type IV, carbon fiber (CF) composite overwrap compressed gas storage tanks by reducing the cost of CF and CF composites. The project team worked to reduce the cost of CF by exploring and testing opportunities for a low-cost alternative precursor material for CF production to supplant market-dominant and costly polyacrylonitrile (PAN). Concurrently, the team aimed to reduce the cost of the tanks at the composite level by improving the interfacial adhesion between the fibers and the matrix resin through the incorporation of low-cost nanoparticles recycled from waste materials, which would reduce the volume of costly CF required to achieve the same tank performance. At the end of the first year, the project team selected mesophase pitch as the primary precursor candidate from a field of materials based on the superior mechanical performance and cost-saving potential. During the second year, the team produced CFs derived from mesophase pitch achieving an average tensile strength of 365.6 ksi and average tensile modulus of 40.74 Msi. Facility availability for spinning and converting these fibers at greater scale has hindered scale-up demonstration, but the team has identified opportunities to conduct this work in the near term. Cost modeling shows that these mesophase pitch-derived CFs can be up to 40% less expensive than PAN-derived CFs due to the lower cost of the feedstock material, higher throughput, greater conversion yield, and lower cost spinning method and compared to PAN. Additionally, the team has demonstrated at lab-scale that nanoparticle coating CFs can significantly increase the interfacial shear strength and load transfer efficiency of CFs in a matrix. Single filament pull-out testing showed a 27% average increase in max interfacial shear strength due to this coating. A continuous method of applying these coatings to a tow of CF has been developed for scale-up. 26 m tows of coated CFs were produced using this system and formed into composite ring samples for ASTM ring burst testing. Issues with the testing protocol have limited assessment of these results. A prototype Type IV tank was designed to meet ANSI HGV2 standards, and the design criteria set out by DOE, using the CF properties developed by the team paired with a proprietary resin matrix, a polyamide liner, and aluminum end bosses. The tank weighs 153.1 kg and with a total capacity of 5.8 kg H2 (5.6 kg usable), which yields a gravimetric capacity of 1.17 kWh/kg. Cost modeling predicts that the tank will have a projected cost of $15.73/kWh. Tank performance modeling does not include considerations for fiber-matrix load transfer efficiency improvements offered by nanoparticle coating method.
Quantitative relationships between film morphology, charge carrier dynamics, and photovoltaic performance in bulk-heterojunction binary vs. ternary acceptor blends
Addressing pertinent and perplexing questions regarding why nonfullerene acceptors (NFAs) promote higher power conversion efficiencies (PCEs) than traditional fullerenes and how photoactive bulk heterojunction (BHJ) film morphology, charge photogeneration, and recombination dynamics dictate solar cell performance have stimulated many studies of polymer solar cells (PSCs), yet quantitative relationships remain limited. Better understanding in these areas offers the potential to advance materials design and device engineering, afford higher PCEs, and ultimate commercialization. Here we probe quantitative relationships between BHJ film morphology, charge carrier dynamics, and photovoltaic performance in model binary and ternary blend systems having a wide bandgap donor polymer, a fullerene, and a promising NFA. We show that optimal PC 71 BM incorporation in a PBDB-TF:ITIC-Th binary system matrix retains the original π-face-on orientation, ITIC-Th crystallinity and BHJ film crystallite dimensions, and reduces film upper surface ITIC-Th segregation. Such morphology changes together simultaneously increase hole (μ h ) and electron (μ e ) mobilities, facilitate light-activated ITIC-Th to PC 71 BM domain electron delocalization, reduce free charge carrier (FC) bimolecular recombination (BR) within PBDB-TF:ITIC-Th mixed regions, and increase FC extraction pathways viaPBDB-TF:PC 71 BM pairs. The interplay of these effects yields significantly enhanced inverted cell short-circuit current density (J SC ), fill factor (FF), and PCE. Unexpectedly, we also find that excessive PC 71 BM in the PBDB-TF:ITIC-Th binary system alters the PBDB-TF orientation to π-edge-on, increases large scale PC 71 BM-rich aggregations and BHJ upper surface PC 71 BM composition. Further, these morphology changes increase parasitic decay processes such as intersystem crossing from photoexcited PC 71 BM, compromising the J SC , FF, and PCE metrics. ITIC-Th X-ray diffraction reveals a unique sidechain-dominated molecular network with previously unknown sidechain-end group stacking, rationalizing the STEM and GIWAXS results, photophysics, and the high μ e . DFT computation reveals charge transfer networks within ITIC-Th crystallites, supporting excited-state electron delocalization from ITIC-Th to PC 71 BM. This structure–property understanding leads to a newly reported NFA blend with PCE near 17%.
Enabling the Broader Use of MOOSE for Nuclear Energy and Other Simulation
This Final Scientific and Technical Report summarizes work performed under the Phase IIA SBIR project “Enabling the Broader Use of MOOSE for Nuclear Energy and Other Simulation” (DE-SC0020906) from August 2023 through August 2025. The objective of the Phase IIA effort was to mature and harden capabilities developed during Phase II, with the goal of enabling practical interoperability between Coreform’s isogeometric analysis (IGA) technologies and the Multiphysics Object-Oriented Simulation Environment (MOOSE), while improving robustness, performance, and scalability for complex, nuclear-relevant geometries. Over the course of Phase IIA, the project established and validated an extraction-based interoperability pathway between Coreform tools and MOOSE. A combined mesh and matrix format was defined collaboratively with MOOSE developers and integrated into the solver, enabling standard MOOSE workflows to operate on data exported from Coreform’s IGA and Flex Representation Method (FRM) pipelines. Early demonstrations validated architectural compatibility using linear solid mechanics problems, while later efforts focused on benchmark testing and external use. By the end of the project period, engineers at BWXT were able to independently set up and execute a simulation using the Coreform–MOOSE workflow and provide direct feedback that informed further refinement. In parallel, substantial effort was devoted to improving the robustness of trimmed U-spline construction for complex CAD geometries. A growing test suite of nuclear-relevant models was compiled through collaboration with multiple stakeholders and used to drive extensive bug fixing and reliability improvements. These efforts resulted in improved robustness and performance, including the addition of fallback capabilities that enhance reliability when the underlying commercial CAD kernel fails. Performance-oriented work progressed later in the project, with the development and demonstration of methods to decompose complex geometries into structured subregions and updated data representations to support more efficient solver processing. Additionally, extensive enhancements to threadsafe parallel data structures and trimming operations established a foundation for scalable processing of large assemblies. Collaboration with Sandia National Laboratories on the SGM geometric modeling kernel advanced to a functioning interface test case, positioning the workflow for future kernel integration. Overall, the Phase IIA effort successfully transitioned the project from architectural proof-of-concept to externally exercised, solver-integrated capability, while clarifying remaining technical challenges related to standardization, performance optimization, and kernel integration.
Graphene reinforced UHMWPE fibers
Thermoplastic polymers are increasingly used in electric vehicles, hydrogen fuel cell vehicles, and other decarbonization applications due to their lightweight and formability. Higher-strength polymers are needed to supplant metals in the vehicle structure, thereby reducing mass and improving efficiency. Ultra-high molecular weight polyethylene (UHMWPE) fibers possess one of the highest strength-to-weight ratios of technical polymers, and further improvement via reinforcement by nanofillers, such as graphene, will expand their performance envelope. Here, in this work, UHMWPE/graphene nanocomposite fibers were gel spun and characterized for their morphological, microstructural, thermal, and mechanical properties. The addition of a low fraction of graphene improved the tensile strength of the fibers by 25% and tensile modulus by 32%. Differential scanning calorimetry showed an increase in melting temperature and degree of crystallinity, which indicates improved coordination of the molecular chains induced by the addition of graphene. The reinforcement also affected the cross-sectional shape of the fibers; the aspect ratio of the fibers’ elliptical shape declined with increasing graphene content showing the skeletal effect of the graphene nanofillers in the polymer matrix. The reinforcing effect of graphene declined above a threshold concentration, and theoretical modeling was applied to demonstrate that increased agglomerates led to reduced properties. This work demonstrates a simple, effective method to produce graphene-reinforced UHMWPE fibers and lays a foundation for understanding the potential for leveraging graphene to form ultra-high-performance nanocomposite fibers for myriad engineering applications.
Enabling Parallel Performance and Portability of Solid Mechanics Simulations Across CPU and GPU Architectures
Efficiently simulating solid mechanics is vital across various engineering applications. As constitutive models grow more complex and simulations scale up in size, harnessing the capabilities of modern computer architectures has become essential for achieving timely results. This paper presents advancements in running parallel simulations of solid mechanics on multi-core CPUs and GPUs using a single-code implementation. This portability is made possible by the C++ matrix and array (MATAR) library, which interfaces with the C++ Kokkos library, enabling the selection of fine-grained parallelism backends (e.g., CUDA, HIP, OpenMP, pthreads, etc.) at compile time. MATAR simplifies the transition from Fortran to C++ and Kokkos, making it easier to modernize legacy solid mechanics codes. We applied this approach to modernize a suite of constitutive models and to demonstrate substantial performance improvements across different computer architectures. This paper includes comparative performance studies using multi-core CPUs along with AMD and NVIDIA GPUs. Results are presented using a hypoelastic–plastic model, a crystal plasticity model, and the viscoplastic self-consistent generalized material model (VPSC-GMM). The results underscore the potential of using the MATAR library and modern computer architectures to accelerate solid mechanics simulations.
Engineering catalytical electrodes for applications in energy areas
An ink formulation and electrode that enhances hydrogen production, oxygen production, carbon dioxide reduction and other electrocatalytic reactions. Embodiments include an ink formulation with polymer binders having different catalytical precursors and a 3D electrode produced by additive manufacturing from the inventor's ink formulation. Various embodiments of the inventor's apparatus, systems, and methods provide inks that that are 3D-printed into patterns that optimize surface area and flow. The catalytic materials are imbedded into the ink matrix which is then printed into a 3D structure that has architecture that optimizes surface area and flow properties.
A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients
Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.
Uncovering the role of nanoscale precipitates on martensitic transformation and superelasticity
Here we characterize the role of coherent nanoscale B2 Ni 50 Al 50 precipitates on the temperature- and stress-induced martensitic phase transformation in nanocrystalline Ni 63 Al 37 shape memory alloys using multi-million-atoms molecular dynamics (MD) simulations. We studied two types of precipitates: one with single crystal precipitates (SXP) and a second where grain boundaries cut through precipitates (PXP). Simulations reveal that the presence of B2 precipitates stabilizes the cyclic flag-shaped stress-strain response, characteristic of superelasticity, and reduces remnant strain. In contrast, single-phase nanocrystalline Ni 63 Al 37 exhibits degradation of the reverse transformation during cyclic loading and, eventually, incomplete reversible transformation within a few cycles. This is consistent with previous experimental findings of ultra-low fatigue in Ni-Ti-Cu alloys with Ti 2 Cu precipitates. The simulations reveal that the presence of precipitates significantly improves the reversibility of the transformation by acting as elastic zones that partially shield the martensitic transformation and drive the reverse transformation. A detailed analysis of the MD trajectories reveals that the martensitic transformation of the matrix induces ultra-large elastic deformation in some of the B2 precipitates (approximately 12%) to the point of resulting in a martensite-like atomic structure.