SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Finding satisfactory models of the fluid motions at the top of the core is important for delineating what kind of dynamo is in operation, for estimating the heat flux into the base of the mantle, and for forecasting the magnetic field forward in time. Each of these aspects will be discussed.
LMI conducted an integrated analysis of airport capacity and environmental constraints. identifying and ranking the key factors limiting achievement of NextGen capacity goals. The primary metric used was projected throughput, which was estimated for the years 2015 and 2025 based on the unconstrained demand forecast from the Federal Aviation Administration, and planned improvements including those proposed in the NextGen plan. A set of 310 critical airports was identified.. collectively accounting for more than 99 percent of domestic air traffic volume; a one-off analytical approach was used to isolate the constraint being assessed. The study considered three capacity constraints (runway.. taxiway, and gate) and three environmental constraints (fuel, NO(x) emissions, and noise). For the ten busiest airports, runway and noise are the primary and secondary constraints in both 2015 and 2025. For the OEP 35 airports and overall for the remaining airports, the most binding constraint is noise. Six of the 10 busiest airports, will face runway constraints in 2025, and 95 will face gate constraints. Nearly every airport will be subject to constraints due to emissions and NOx. Runway and taxi constraints are more concentrated in the large airports: environmental constraints are present at almost every airport regardless of size.
In the middle to high latitude and alpine regions, the seasonal snow pack can dominate the surface energy and water budgets due to its high albedo, low thermal conductivity, high emissivity, considerable spatial and temporal variability, and ability to store and then later release a winters cumulative snowfall (Cohen, 1994; Hall, 1998). With this in mind, the snow drought across the U.S. has raised questions about impacts on water supply, ski resorts and agriculture. Knowledge of various snow pack properties is crucial for short-term weather forecasts, climate change prediction, and hydrologic forecasting for producing reliable daily to seasonal forecasts. One potential source of this information is the multi-institution North American Land Data Assimilation System (NLDAS) project (Mitchell et al., 2004). Real-time NLDAS products are used for drought monitoring to support the National Integrated Drought Information System (NIDIS) and as initial conditions for a future NCEP drought forecast system. Additionally, efforts are currently underway to assimilate remotely-sensed estimates of land-surface states such as snowpack information into NLDAS. It is believed that this assimilation will not only produce improved snowpack states that better represent snow evolving conditions, but will directly improve the monitoring of drought.
The recalibration of the International Sunspot Number brings new challenges to predictions of Solar Cycle 25. One is that the list of extrema for the original series is no longer usable because the values of all maxima and minima are different for the new version of the sunspot number. Timings of extrema are less sensitive to the recalibration but are a natural result of the calculation. Predictions of Solar Cycle 25 published before 2016 must be converted to the new version of the sunspot number. Any prediction method that looks across the entire time span will have to be reconsidered because values in the nineteenth century were corrected by a larger factor than those in the twentieth century. We report a list of solar maxima and minima values and timings based on the recalibrated sunspot number. Naïve forecasts that depend only on the current values of the time series are common in economic studies. Several naïve predictions of Solar Cycle 25, the climatological average (180 ± 60), two versions of the inertial forecast, and two versions of the even-odd forecast, are derived from that table. The climatological average forecast is the baseline for more accurate predictions and the initial forecast in assimilative models of the Sun. It also provides the error estimate for Monte Carlo techniques that anticipate the long-term effects on the terrestrial environment. The other four predictions are shown to be statistically insignificant.
PolCube is a 12U CubeSat + polarimeter instrument designed by NASA Langley and the Korea Astronomy and Space Science Institute (KASI) for Earth Science. PolCube is based on the PolCam polarimeter onboard the Korean Pathfinder Lunar Observatory (KPLO) that launched in August 2022. The objective of the PolCube instrument is to retrieve detailed fine-mode (pollution and smoke) and coarse-mode (sea-salt and dust) aerosol properties over the ocean for a range of light to heavy aerosol loadings using its polarimetric-imaging capability at multiple angles and wavelengths from 410 − 865 nm. An additional objective is to discriminate aerosols from thin clouds. We quantify the performance of aerosol and ocean remote sensing products from the PolCube polarimeter instrument using the Microphysical Aerosol Properties from Polarimetry (MAPP) remote sensing retrieval algorithm. PolCube’s accurate and high-resolution aerosol-retrieval products will provide unique spatial and temporal coverage of the Earth that can be used synergistically with other instruments, such as the PACE (Plankton, Aerosols, Clouds and Ecosystems) and GEMS (Geostationary Environmental Monitoring Spectrometer) mission to improve air-quality forecasting. We present the PolCube-MAPP retrieval algorithm, which used optimal estimation and artificial intelligence, as well as multiple powerful inherent optical property look-up-tables for the Earth’s aerosol, cloud, and hydrosol particles. We estimate that PolCube can retrieve total aerosol optical depth at 555 nm (AOD555) within ±0.068, fine-mode AOD555 within ±0.078, and fine-mode single-scattering albedo within ±0.036, where all uncertainties are expressed as one standard deviation (1σ).
The intensity, spatial, and temporal changes in precipitation were examined in three North Atlantic hurricanes during 1989 (Dean, Gabrielle, and Hugo) using precipitation estimates made from Special Sensor Microwave/Imager (SSM/I) measurements. In addition, analyses from a barotropic hurricane forecast model and the European Centre for Medium-Range Weather Forecast model were used to examine the relationship between the evolution of the precipitation in these tropical cyclones and external forcing. The external forcing parameters examined were (1) mean climatological sea surface temperatures, (2) vertical wind shear, (3) environmental tropospheric water vapor flux, and (4) upper-tropospheric eddy relative angular momentum flux convergence. The analyses revealed that (1) the SSM/I precipitation estimates were able to delineate and monitor convective ring cycles similar to those observed with land-based and aircraft radar and in situ measurements; (2) tropical cyclone intensification was observed to occur when these convective rings propagated into the inner core of these systems (within 111 km of the center) and when the precipitation rates increased; (3) tropical cyclone weakening was observed to occur when these inner-core convective rings dissipated; (4) the inward propagation of the outer convective rings coincided with the dissipation of the inner convective rings when they came within 55 km of each other; (5) in regions with the combined warm sea surface temperatures (above 26 C) and low vertical wind shear (less than 5 m/s), convective rings outside the region of strong lower-tropospheric inertial stability could be initiated by strong surges of tropospheric moisture, while convective rings inside the region of strong lower-tropospheric inertial stability could be enhanced by upper-tropospheric eddy relative angular momentum flux convergence.
A number of techniques for predicting solar activity on a solar cycle time scale are identified, described, and tested with historical data. Some techniques, e.g,, regression and curve-fitting, work well as solar activity approaches maximum and provide a month- by-month description of future activity, while others, e.g., geomagnetic precursors, work well near solar minimum but provide an estimate only of the amplitude of the cycle. A synthesis of different techniques is shown to provide a more accurate and useful forecast of solar cycle activity levels. A combination of two uncorrelated geomagnetic precursor techniques provides the most accurate prediction for the amplitude of a solar activity cycle at a time well before activity minimum. This precursor method gave a smoothed sunspot number maximum of 154+21 for cycle 23. A mathematical function dependent upon the time of cycle initiation and the cycle amplitude then describes the level of solar activity for the complete cycle. As the time of cycle maximum approaches a better estimate of the cycle activity is obtained by including the fit between recent activity levels and this function. This Combined Solar Cycle Activity Forecast now gives a smoothed sunspot maximum of 140+20 for cycle 23. The success of the geomagnetic precursors in predicting future solar activity suggests that solar magnetic phenomena at latitudes above the sunspot activity belts are linked to solar activity, which occurs many years later in the lower latitudes.
It has long been well known that actual system reliability typically falls well short of early estimates. Failure rates are often ten or more times higher than anticipated. Many reasons have been given for this, but over-optimism is the fundamental cause of too-favorable reliability predictions. Most forecasts of reliability are essentially best-case scenarios, as are predictions of budget and schedule. Confident engineers assemble estimates bottom-up, including the known factors and ignoring problems that they hope won’t happen. Traditional reliability estimation is based on simply summing up the component failure rates. This ignores most actual failure causes. The way to reduce over-optimism is to use the historical system level failure rate from similar projects. Adjustments should not be made based purely on engineering judgment, but only if there is so logical quantitative justification. The traditional component-based reliability estimate is useful as a lower bound on the system failure rate. The difference between this lower bound component-based reliability and the historical system level reliability indicates how much of the total failure rate is due to system level problems rather than component failures.
It has long been well known that actual system reliability typically falls well short of early estimates. Failure rates are often ten or more times higher than anticipated. Many reasons have been given for this, but over-optimism is the fundamental cause of too-favorable reliability predictions. Most forecasts of reliability are essentially best-case scenarios, as are predictions of budget and schedule. Confident engineers assemble estimates bottom-up, including the known factors and ignoring problems that they hope won't happen. Traditional reliability estimation is based on simply summing up the component failure rates. This ignores most actual failure causes. The way to reduce over-optimism is to use the historical system level failure rate from similar projects. Adjustments should not be made based purely on engineering judgment, but only if there is so logical quantitative justification. The traditional component-based reliability estimate is useful as a lower bound on the system failure rate. The difference between this lower bound component-based reliability and the historical system level reliability indicates how much of the total failure rate is due to system level problems rather than component failures
The results of comparisons of the solar flux models are presented. (The wavelength lambda = 10.7 cm radio flux is the best indicator of the strength of the ionizing radiations such as solar ultraviolet and x-ray emissions that directly affect the atmospheric density thereby changing the orbit lifetime of satellites. Thus, accurate forecasting of solar flux F sub 10.7 is crucial for orbit determination of spacecrafts.) The measured solar flux recorded by National Oceanic and Atmospheric Administration (NOAA) is compared against the forecasts made by Schatten, MSFC, and NOAA itself. The possibility of a combined linear, unbiased minimum-variance estimation that properly combines all three models into one that minimizes the variance is also discussed. All the physics inherent in each model are combined. This is considered to be the dead-end statistical approach to solar flux forecasting before any nonlinear chaotic approach.
Simulations of hydrological fields as well as water, energy and carbon fluxes from the land surface to the atmosphere are crucial for a wide range of applications, including agricultural advisories, forecasts of (short-term) atmospheric behavior and seasonal weather predictions including forecasts of extreme events, such as heatwaves or droughts. The NASA Soil Moisture Active Passive (SMAP) mission Level-4 (L4) Eco-Hydrology (ECO) project aims to improve modeled estimates of the terrestrial water, energy and carbon fluxes and states by developing a fully-coupled hydrology-vegetation data assimilation (DA) algorithm. The DA system is developed for the NASA Goddard Earth Observing System version 5 (GEOS-5) Catchment-CN land surface model, which combines land hydrology components of the GEOS-5 Catchment model with dynamic vegetation components of the Community Land Model version 4. Catchment-CN fully couples the terrestrial water, energy and carbon cycles, allowing feedbacks from the land hydrology to the biosphere and vice versa. For SMAP L4 ECO a calibration of the Catchment-CN vegetation parameterization against observations of the fraction of absorbed photosynthetically active radiation (FPAR) from the Moderate Resolution Imaging Spectroradiometer (MODIS) is implemented to improve the model's standalone skill. Next, the DA algorithm used to produce the SMAP L4 soil moisture product is adapted to Catchment-CN to assimilate SMAP brightness temperatures and inform the model's land hydrology component. The DA system is further extended to assimilate MODIS FPAR observations in order to constrain the model's dynamic vegetation component. In this presentation, we demonstrate that the Catchment-CN parameter calibration leads to more realistic vegetation simulations and reduces the root mean squared error between modeled and observed vegetation states across the model's various plant functional types. We also show that the assimilation of SMAP observations is able to improve the average correlation, bias and unbiased RMSE between the modeled surface and root zone soil moisture estimates, and ground observations from the SMAP core validation sites.
The economic value of information produced by an assumed operational version of an earth resources survey satellite of the ERTS class is assessed. The theoretical capability of an ERTS system to provide improved agricultural forecasts is analyzed and this analysis is used as a reasonable input to the econometric methods derived by ECON. An econometric investigation into the markets for agricultural commodities is summarized. An overview of the effort including the objectives, scopes, and architecture of the analysis, and the estimation strategy employed is presented. The results and conclusions focus on the economic importance of improved crop forecasts, U.S. exports, and government policy operations. Several promising avenues of further investigation are suggested.
Characterization of the error associated to satellite rainfall estimates is a necessary component of deterministic and probabilistic frameworks involving spaceborne passive and active microwave measurements for applications ranging from water budget studies to forecasting natural hazards related to extreme rainfall events. We focus here on the error structure of Tropical Rainfall Measurement Mission (TRMM) Precipitation Radar (PR) quantitative precipitation estimation (QPE) at ground. The problem was addressed in a previous paper by comparison of 2A25 version 6 (V6) product with reference values derived from NOAA/NSSL's ground radar-based National Mosaic and QPE system (NMQ/Q2). The primary contribution of this study is to compare the new 2A25 version 7 (V7) products that were recently released as a replacement of V6. This new version is considered superior over land areas. Several aspects of the two versions are compared and quantified including rainfall rate distributions, systematic biases, and random errors. All analyses indicate V7 is an improvement over V6.
Relative to other geophysical variables, soil moisture (SM) estimates derived from land surface models (LSMs) and land data assimilation systems (LDAS) are difficult to transfer between platforms and applications. This difficulty stems from the highly model-dependent nature of LSM SM estimates and differences in the vertical support of discretized SM values. As a result, operational SM estimates generated by one LSM (or LDAS) cannot generally be directly applied to a hydrologic monitoring or forecast system designed around a second LSM. This lack of transferability is particularly problematic for LDAS applications, where the time, expertise, and computational resources required to generate an operational LDAS analysis cannot be practically duplicated for every LSM-specific application. Here, we develop a set of simple regression tools for translating SM estimates between LSMs and multiple LDAS analyses. Results demonstrate that simple multivariate linear regression - utilizing independent variables based on multi-layer and temporally lagged SM estimates - can significantly improve upon baseline transformation approaches using direct percentile matching. The proposed regression approaches are effective for both the LSM-to-LSM and LDAS-to-LDAS transformation of multi-layer SM percentiles. Application of this approach will expand the utility of existing, high-quality (but LSM-specific) operational sources of SM information like the NASA Soil Moisture Active Passive Level-4 Soil Moisture product.
Results provided by two different assimilation methodologies involving data from passive and active space-borne microwave instruments are presented. The impact of the precipitation estimates produced by the TRMM Microwave Imager (TMI) and Special Sensor Microwave/Imager (SSM/I) in a previously developed 1D variational continuous assimilation algorithm for assimilating tropical rainfall is shown on two hurricane cases. Results on the impact of the SeaWinds scatterometer on the intensity and track forecast of a mid-Atlantic hurricane are also presented. This work is the outcome of a collaborative effort between NASA and NOAA and indicates the substantial improvement in tropical cyclone forecasting that can result from the assimilation of space-based data in global atmospheric models.
The Tropical Rainfall Measuring Mission (TRMM) has completed more than three years in orbit. A summary of research highlights will be presented focusing on application of TRMM data to topics ranging from climate analysis, through improving forecasts, to microphysical research. Examples and plans for operational use of TRMM data in tropical cyclone and other applications will be given. The status of precipitation estimates from different instruments and algorithms will be described. Monthly surface rainfall estimates over the ocean based on different instruments on TRMM currently differ by 20% in overall mean. In addition, time changes in global ocean rainfall between El Nino and La Nina conditions show a difference in sign between the active and passive microwave products. These differences are not surprising considering the different type of observations available for the first time from TRMM with both the passive and active microwave sensors. Resolving the differences will strengthen the validity and utility of ocean rainfall estimates. The TRMM rainfall estimates are intercompared among themselves and with other estimates, including those of the standard, monthly Global Precipitation Climatology Project (GPCP) analysis. The GPCP analysis agrees roughly in magnitude with the passive microwave-based TRMM estimates which is not surprising considering GPCP over-ocean estimates are based on passive microwave observations. A three-year TRMM rainfall climatology is presented, including anomaly fields related to the changing ENSO situation during the mission. Results of using TRMM information to calibrate other passive microwave observations and geosynchronous infrared rainfall estimates and then merging them those estimates into a global, tropical 3-hour time resolution analysis will also be described.
The SEASAT-A commercial demonstration program ASVT is described. The program consists of a set of experiments involving the evaluation of a real time data distributions system, the SEASAT-A user data distribution system, that provides the capability for near real time dissemination of ocean conditions and weather data products from the U.S. Navy Fleet Numerical Weather Central to a selected set of commercial and industrial users and case studies, performed by commercial and industrial users, using the data gathered by SEASAT-A during its operational life. The impact of the SEASAT-A data on business operations is evaluated by the commercial and industrial users. The approach followed in the performance of the case studies, and the methodology used in the analysis and integration of the case study results to estimate the actual and potential economic benefits of improved ocean condition and weather forecast data are described.
A pattern recognition scheme that is used to generate initial seeds or 'first guess' fields for clustering the discrete lightning discharges into storm cells is presented. The clustering process is critically dependent on the prior accuracy of the lightning location estimates. The generation of subsequent storm life-cycle time series (for extrapolation forecasting) also relies on the cluster analysis procedure assigning the correct number of lightning discharges (objects) to the proper storms (groups). The advantages and limitations of different clustering strategies for storm identification and tracking are examined. Storm identification with lightning data alone is compared to storm identification with radar alone, and some synergies for sensor fusion are explored.