Characterizing environment-dependent fracture mechanisms of ceramic matrix composites via digital image correlation
Not provided.
Materials Science↗
SEARCH · Search NASA
Results for “flexures”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Data Processing Package for Cyclic Integrated Reversible Bending Fatigue Testing
A data processing software package has been introduced. The package was developed using MATLAB with the aid of the Curve Fitting Toolbox. The package is made up of four modules: pre-processing, data processing for static testing, data processing for monitoring, and data processing for measurements. CIRFT data are structured with multiple levels of architecture involving group, specimen, session, and scan/block. The degree of complexity of the data structure depends on whether a test is static or cyclic.The test results are presented in figures, scatter plots, and tables. For static testing, the output in tables provides bending mechanical properties and characteristic points of moment–curvature relation: flexural rigidities in linear segments of loading and unloading stages, intersection points between characteristic segments of the curve, and equivalent stress and strain quantities. For cyclic testing, the table output lists control and fatigue life and responsive/dependent quantities including moment, curvature, flexural rigidity, flexural hysteresis, rigidity phase angle, and equivalent stresses and strains. In addition, derivatives such as half-gage length and sensor spacing correction are included. The output also provides standard deviations of the reported quantities when they are applicable or available. The data processing package can serve as a fundamental characterization tool in mechanical study of materials. The package is intended primarily for data processing for the CIRFT process and can also be used in applications for which similar testing requirements exist.
36 MATERIALS SCIENCE↗
IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades
(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.
17 WIND ENERGY↗
VitriEdge: Repairable & Durable Vitrimer Coatings for Wind Turbine Blade Leading Edges
The primary goal of this Level 1b incubator project was to explore the use of vitrimer coatings for repair of leading-edge erosion on end-of-life wind turbine blade surfaces, beyond coating strength of adhesion which has previously been demonstrated in the Level 1a project. Uniform vitrimer coatings (thickness: 400 µm) were applied to two end-of-life wind turbine blades for flexural, fatigue, and laminate tensile testing where the addition of the coating did not produce any statistical variation in tensile properties with minor drops in flexural strength for some laminate formulations. However, a <2% variation in storage modulus was measured for laminate structures (i.e., blade samples with vitrimer coatings) across 100,000 flexural cycles and upon laminate tensile failure, the vitrimer coatings displayed no visible signs of delamination. In addition, three methods to heal vitrimer coating damage was displayed: oven heating, addition of hot water, and a forced convection heat gun. All three heating and healing mechanisms demonstrated significant healing with scratch depths decreasing between 79-91% at healing times ranging between 1-min and 10-minutes. Finally, a water jet machine was used to simulate rain erosion for both the blade surfaces and vitrimer-coated blade surfaces where the diameter and depth of the damage was recorded as a function of exposure time, water pressure, height of exposure, and angle of exposure. Of interest, while the vitrimer coating did not significantly lessen the damage experienced during rain erosion, the addition of vitrimer composite coatings(5 wt.% mica addition) did result in a crack-resistant, durable coating capable of self-healing behavior and in all cases the angle of rain exposure was the most critical parameter explored. It is crucial to continue exploring this space where vitrimer coatings are of interest for both their self-healing properties and potential use as reversible adhesives.
17 WIND ENERGY↗
The Impact of Carbonation Curing on the Fatigue Behavior of Polyvinyl Alcohol Engineered Cementitious Composites (PVA-ECC)
Use of Engineered Cementitious Composites (ECC) has been proven to enhance structural fatigue resistance and reduce the use-phase emissions for transportation infrastructure. Carbonation curing offers an opportunity to reduce the embodied carbon of ECC via direct CO 2 sequestration. In this study, the impact of carbonation curing on ECC’s fatigue resistance was examined. ECC’s CO 2 uptake, static flexural behavior, flexural fatigue performance, and single fiber pull-out behavior were studied experimentally. Midspan deflection up to 3 million cycles under fatigue load, fatigue stress-life relationship, and failure mechanism for carbonation-cured and air-cured ECC were investigated. Carbonation curing was found to significantly improved the fatigue life of ECC and lowered the midspan deflection under the same stress. Further, CO 2 -cured ECC can achieve >20% CO 2 uptake per cement mass after 24-hour carbonation curing. Carbonation curing increased ECC’s flexural strength by 32% and promoted crack width control capability, with maximum post-fatigue crack width reduced from 148 μm to 76 μm. As a result, the positive impact of carbonation curing on the fatigue behavior of ECC simultaneously lowers the embodied and operational carbon of ECC structural members subjected to fatigue loading during service.
36 MATERIALS SCIENCE↗
Flax–Reinforced Vitrimer Epoxy Composites Produced via RTM
Composite laminates were produced by RTM using similar glass and flax fabrics and both vitrimer epoxy and aerospace-grade epoxy, both formulated for liquid molding. Tensile and flexural properties were measured and compared, revealing that the vitrimer composites exhibited equivalent performance in flexural strength and tensile modulus, but slightly lower performance in tensile strength relative to reference epoxy composites. In general, glass–fiber composites outperformed flax–fiber composites in tension. However, both glass and flax–fiber composites yielded roughly equivalent flexural strength and tensile modulus-to-weight ratios. Flax fabrics were recovered from composites by matrix dissolution, and a second-life laminate showed full retention of the mechanical properties relative to those produced from fresh flax. Finally, a demonstration of re-forming was undertaken, showing that simple press-forming can be used to modify the composite shape. However, re-forming to a flat configuration resulted in local fiber damage and a decrease in mechanical properties. An alternative forming method was demonstrated that resulted in less fiber damage, indicating that further refinements might lead to a viable forming and re-forming process.
Martinez, Patricio (ORCID:0000000225884389)↗
Effects of environment on the fatigue of graphite-epoxy composites
Torsional and flexural fatigue tests were performed on both uniaxial (0 deg) and crossplied (plus or minus 45 deg) graphite-epoxy materials at temperatures of 24 and 74 C in environments of air and water. The results of the torsion testing showed that the number of cycles required to cause an initial decrease in stiffness as well as the rate of stiffness loss was a function of temperature and environment; the most significant losses were noted for tests at the higher temperature in water. The torsional fatigue specimens were subsequently tested in four-point bending to determine the effect of torsional damage on longitudinal properties. This damage caused changes in the flexural stiffness, failure stress, and failure energy, depending on the stress and environmental histories. The flexural fatigue tests also showed a significant effect of water (at 24 C) on the material behavior. These results are compared with the results of previous investigations and are discussed in terms of proposed damage mechanisms.
Sumsion, H. T.↗
Time temperature-stress dependence of boron fiber deformation
Flexural stress relaxation (FSR) and flexural internal friction (FIF) techniques were employed to measure the time-dependent deformation of boron fibers from -190 to 800 C. The principal specimens were 203 micrometers diameter fibers commercially produced by chemical vapor deposition (CVD) on a 13 micrometer tungsten substrate. The observation of complete creep strain recovery with time and temperature indicated that CVD boron fibers deform flexurally as anelastic solids with no plastic component.
Dicarlo, J. A.↗
Super-hybrid composites - An emerging structural material
Specimens of super-hybrids and advanced fiber composites were subjected to extensive tests to determine their mechanical properties, including impact and thermal fatigue. The super-hybrids were fabricated by a procedure similar to that reported by Chamis et al., (1975). Super-hybrids subjected to 1000 cycles of thermal fatigue from -100 to 300 F retained over 90% of their longitudinal flexural strength and over 75% of their transverse flexural strength; their transverse flexural strength may be as high as 8 times that of a commercially supplied boron/1100-Al composite. The thin specimen Izod longitudinal impact resistance of the super-hybrids was twice that of the boron/110-Al material. Super-hybrids subjected to transverse tensile loads exhibited nonlinear stress-strain relationships. The experimentally determined initial membrane (in-plane) and bending elastic properties of super-hybrids were predicted adequately by linear laminate analysis.
Chamis, C. C.↗
Synthesis techniques for insensitive aircraft control systems
Comparative evaluation of seven insensitive synthesis techniques applied to the control of the longitudinal axis and symmetric flexure modes of the C-5A aircraft is described. These techniques have the common goal of achieving insensitivity to parameter uncertainties and unmodeled dynamics. For this comparison, the 'complete' model was assumed to consist of rigid body dynamics, fifteen flexure modes, unsteady aerodynamics, gust dynamics, and first order actuators for two control inputs. Thirteen flexure modes and the unsteady aerodynamics were treated as neglected dynamics. Dynamic pressure, structural frequency and damping, and the stability derivative were treated as uncertain parameters. Design specifications consisted of a transient response criterion, statistical response criteria, eigenvalue criteria and stability margins. A nominal controller designed without regard to sensitivity served as a benchmark for performance comparisons of the insensitive controllers.
Harvey, C. A.↗
Measurement of the time-temperature dependent dynamic mechanical properties of boron/aluminum composites
A flexural vibration test and associated equipment were developed to accurately measure the low strain dynamic modulus and damping of composite materials from -200 C to over 500 C. The basic test method involves the forced vibration of composite bars at their resonant free-free flexural modes in a high vacuum cryostat furnace. The accuracy of these expressions and the flexural test was verified by dynamic moduli and damping capacity measurements on 50 fiber volume percent boron/aluminum (B/Al) composites vibrating near 2000 Hz. The phase results were summarized to permit predictions of the B/Al dynamic behavior as a function of frequency, temperature, and fiber volume fraction.
Dicarlo, J. A.↗
Prediction of properties of intraply hybrid composites
Equations based on the mixtures rule are presented for predicting the physical, thermal, hygral, and mechanical properties of unidirectional intraply hybrid composites (UIHC) from the corresponding properties of their constituent composites. Bounds were derived for uniaxial longitudinal strengths, tension, compression, and flexure of UIHC. The equations predict shear and flexural properties which agree with experimental data from UIHC. Use of these equations in a composites mechanics computer code predicted flexural moduli which agree with experimental data from various intraply hybrid angleplied laminates (IHAL). It is indicated, briefly, how these equations can be used in conjunction with composite mechanics and structural analysis during the analysis/design process.
Chamis, C. C.↗
Ultra-high modulus organic fiber hybrid composites
An experimental organic fiber, designated Fiber D, was characterized, and its performance as a reinforcement for composites was investigated. The fiber has a modulus of 172 GPa, tensile strength of 3.14 GPa, and density of 1.46 gm/cu cm. Unidirectional Fiber D/epoxy laminates containing 60 percent fiber by volume were evaluated in flexure, shear, and compression, at room temperature and 121 C in both the as fabricated condition and after humidity aging for 14 days at 95 percent RH and 82 C. A modulus of 94.1 GPa, flexure strength of 700 MPa, shear strength of 54 MPa, and compressive strength of 232 MPa were observed at room temperature. The as-fabricated composites at elevated temperature and humidity aged material at room temperature had properties 1 to 20 percent below these values. Combined humidity aging plus evaluated temperature testing resulted in even lower mechanical properties. Hybrid composite laminates of Fiber D with Fiber FP alumina or Thornel 300 graphite fiber were also evaluated and significant increases in modulus, flexure, and compressive strengths were observed.
Champion, A. R.↗
Vibration damping characteristics of graphite/epoxy composites for large space structures
Limited data on extensional and flexural damping of small specimens of graphite/epoxy and unreinforced epoxy resin were obtained. Flexural damping was measured using a forced vibration technique based on resonant flexural vibration of shaker excited double cantilever specimens. Extensional damping was measured by subjecting similar specimens to low frequency sinusoidal oscillation in a servohydraulic tensile testing machine while plotting load versus extensional strain. Damping was found to vary slowly and continuously over the frequency range 0.01 - 1000 Hz, and no drastic transitions were observed. Composite damping was found to be less than neat resin damping. Comparison of small specimen damping values with assembled column damping values seems to indicate that, for those materials, material damping is more important than joint damping. The data reported was limited not by the test apparatus, but by signal conditioning and data acquisition. It is believed that filtering of the strain gage signals and the use of digital storage with slow playback will make it possible to extend the frequency and amplitude ranges significantly.
Gibson, R. F.↗
Compression behavior of unidirectional fibrous composite
The longitudinal compression behavior of unidirectional fiber composites is investigated using a modified Celanese test method with thick and thin test specimens. The test data obtained are interpreted using the stress/strain curves from back-to-back strain gages, examination of fracture surfaces by scanning electron microscope, and predictive equations for distinct failure modes including fiber compression failure, Euler buckling, delamination, and flexure. The results show that the longitudinal compression fracture is induced by a combination of delamination, flexure, and fiber tier breaks. No distinct fracture surface characteristics can be associated with unique failure modes. An equation is described which can be used to extract the longitudinal compression strength knowing the longitudinal tensile and flexural strengths of the same composite system.
Sinclair, J. H.↗
Pressure suit joint analyzer
A measurement system for simultaneously measuring torque and angular flexure in a pressure suit joint is described. One end of a joint under test is held rigid. A torque transducer is pivotably supported on the other movable end of a joint. A potentiometer is attached to the transducer by an arm. The wiper shaft of the potentiometer is gripped by a reference arm that rotates the wiper shaft the same angle as the flexure of joint. A signal is generated by the potentiometer which is representative of the joint flexure. A compensation circuit converts the output of the transducer to a signal representative of joint torque.
Vykukal, H. C.↗
The negative gravity field over the 85 deg E ridge
Two north-south ridges in the basement topography of the Bay of Bengal may be observed on an isopach map at 85 and at 90 deg E. Free-air gravity anomaly profiles across the region show a strong gravity low (about -60 mGal) over the 85 deg E ridge, and a gravity high over the other. Using a simple two-stage loading model, the negative gravity anomaly over the 85 deg E ridge is explained as a direct consequence of sediment loading, and the flexural rigidity of the lithosphere when the ridge was formed is estimated to have been about 180 times less than the flexural rigidity during the sediment loading. An approximate relationship between flexural rigidity and crustal age shows that the 85 deg E ridge was formed on relatively young lithosphere, 5-15 million years old, and that it was buried when the lithosphere was 40-80 million years old. The alteration of the gravity field by a thick layer of sediments may occur in other large sedimentary basins or along continental margins.
Liu, C.-S.↗
Bathymetric prediction from Seasat altimeter data
The linear response function technique is used to analyze two 1300 km tracks of Seasat altimeter data and corresponding bathymetry in the Musician Seamounts region north of Hawaii. A predictive filter is developed which can operate on Seasat altimetry in poorly surveyed oceanic regions to indicate the presence of major bathymetric anomalies. Modelling of the bathymetry-geoid correlation in the Musician region is attempted using the elastic plate model. The flexural rigidity of the plate is not well constrained by the data but appears to be in the range 5 x 10 to the 21st N m up to 5 x 10 to the 22nd N m at the time of loading. Since the Musician Seamounts and the crust on which they lie are both Late Cretaceous in age, this value represents the effective flexural rigidity of very young lithosphere that was 'frozen in' at the time of volcanism. The modelling indicates that the general form of a predictive filter will strongly depend on various geologic parameters, especially the effective flexural rigidity.
Dixon, T. H.↗