Search NASA⌕ Search

SEARCH · Search NASA

Results for “flight path angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

The effect of impact angle on craters formed by hypervelocity particles

The Space Power Institute (SPI) at Auburn University has conducted experiments on the effects of impact angle on crater morphology and impactor residue retention for hypervelocity impacts. Copper target plates were set at angles of 30 deg, 45 deg, 60 deg, and 75 deg from the particle flight path. For the 30 deg and 45 deg impacts, in the velocity regime greater than 8 km s(exp -1) the resultant craters are almost identical to normal incidence impacts. The only difference found was in the apparent distribution of particle residue within the crater, and further research is needed to verify this. The 60 deg and 75 deg impacts showed marked differences in crater symmetry, crater lip shape, and particle residue distribution in the same velocity regime. Impactor residue shock fractionation effects have been quantified in first-order. It is concluded that a combination of analysis techniques can yield further information on impact velocity, direction, and angle of incidence.

Hill, David C.↗
NASA NTRS1992

Control integration concept for hypersonic cruise-turn maneuvers

Piloting difficulties associated with conducting aircraft maneuvers in hypersonic flight are caused in part by the nonintuitive nature of the aircraft response and the stringent constraints anticipated on allowable angle of attack and dynamic pressure variations. An approach is documented that provides precise, coordinated maneuver control during excursions from a hypersonic cruise flight path and the necessary flight condition constraints. The approach is to achieve specified guidance commands by resolving altitude and cross range errors into a load factor and bank angle command by using a coordinate transformation that acts as an interface between outer and inner loop flight controls. This interface, referred to as a 'resolver', applies constraints on angle of attack and dynamic pressure perturbations while prioritizing altitude regulation over cross range. An unpiloted test simulation, in which the resolver was used to drive inner loop flight controls, produced time histories of responses to guidance commands and atmospheric disturbances at Mach numbers of 6, 10, 15, and 20. Angle of attack and throttle perturbation constraints, combined with high speed flight effects and the desire to maintain constant dynamic pressure, significantly impact the maneuver envelope for a hypersonic vehicle.

Raney, David L.↗
NASA NTRS1975

Long-range energy-state maneuvers for minimum time to specified terminal conditions

The calculus of variations and energy-state approximation are used to determine the optimum maneuvers in three-dimensional minimum-time aircraft flight paths to a specified final point or line. Constraints on thrust, Mach number, angle of attack, dynamic pressure, and load factor are included. It is shown that when the initial range is sufficiently large that the maximum velocity constraint is encountered en route, the calculation of minimum-time maneuvers can be greatly simplified by a separation of arcs into two two-parameter problems. Suboptimal paths along which the bank angle is restricted to three discrete values (negative maximum angle, 0, positive maximum angle) compare favorably with the optimum, continuous bank angle solutions for transonic speeds and below.

Parsons, M. G.↗
NASA NTRS1991

Analysis of unsteady pressures induced on a body by a rotor

An analysis was conducted on the unsteady pressures measured on a body surface in proximity to a rotor. Unsteady pressures were measured at strategic points on the body in forward flight at various combination of advance ratio, rotor thrust, and tip-path-plane angle. It was found that the local values of unsteady pressure were significantly altered by small changes in rotor thrust and advance ratio; tip-path-plane angle variations had a much smaller effect. Four characteristic pressure signatures representative of (1) blade passage, (2) close wake interactions with the body, (3) wake impingement on the body, and (4) postwake impingement were distinguished. These classifications were supported by correlations with shadowgraphic flow visualization of the rotor wake/body interaction, as well as unsteady potential flow models. This general classification of the surface pressure signatures has permitted a greater physical understanding of the overall air loads and possible mechanisms responsible for the interactional effects between a helicopter rotor and its fuselage.

Bi, Nai-Pei↗
NASA NTRS2003

Engine Installation Effects of Four Civil Transport Airplanes: Wallops Flight Facility Study

The National Aeronautics and Space Administration (NASA), Langley Research Center (LaRC), the Environmental Measurement and Modeling Division of the United States Department of Transportation s John A. Volpe National Transportation Systems Center (Volpe), and several other organizations (see Appendix A for a complete list of participating organizations and individuals) conducted a noise measurement study at NASA s Wallops Flight Facility (Wallops) near Chincoteague, Virginia during September 2000. This test was intended to determine engine installation effects on four civil transport airplanes: a Boeing 767-400, a McDonnell-Douglas DC9, a Dassault Falcon 2000, and a Beechcraft King Air. Wallops was chosen for this study because of the relatively low ambient noise of the site and the degree of control over airplane operating procedures enabled by operating over a runway closed to other uses during the test period. Measurements were conducted using a twenty microphone U-shaped array oriented perpendicular to the flight path; microphones were mounted such that ground effects were minimized and low elevation angles were observed.

Fleming, Gregg G.↗
NASA NTRS2007

Measurement and Characterization of Helicopter Noise in Steady-State and Maneuvering Flight

A special acoustic flight test program was performed on the Bell 206B helicopter outfitted with an in-flight microphone boom/array attached to the helicopter while simultaneous acoustic measurements were made using a linear ground array of microphones arranged to be perpendicular to the flight path. Air and ground noise measurements were made in steady-state longitudinal and steady turning flight, and during selected dynamic maneuvers. Special instrumentation, including direct measurement of the helicopter s longitudinal tip-path-plane (TPP) angle, Differential Global Positioning System (DGPS) and Inertial Navigation Unit (INU) measurements, and a pursuit guidance display were used to measure important noise controlling parameters and to make the task of flying precise operating conditions and flight track easier for the pilot. Special care was also made to test only in very low winds. The resulting acoustic data is of relatively high quality and shows the value of carefully monitoring and controlling the helicopter s performance state. This paper has shown experimentally, that microphones close to the helicopter can be used to estimate the specific noise sources that radiate to the far field, if the microphones are positioned correctly relative to the noise source. Directivity patterns for steady, turning flight were also developed, for the first time, and connected to the turning performance of the helicopter. Some of the acoustic benefits of combining normally separated flight segments (i.e. an accelerated segment and a descending segment) were also demonstrated.

Schmitz, Fredric H.↗
NASA NTRSDate not supplied

A Web-Based Negotiation Tool for Conflict Resolution in Upper Class E Traffic Management

In Upper Class E airspace 60,000 feet (or Flight level / FL600), vehicles such as High Altitude Long Endurance (HALE) balloons and slow fixed-wing gliders have diverse vehicle characteristics and limited maneuverability. Due to these unique characteristics of high-altitude operations, a new type of strategic negotiation-based conflict resolution method has been proposed to avoid potential conflict between vehicles in Upper Class E airspace, well in advance of the conflict point and with ample time for bilateral negotiation. This paper introduces the first real-time web-based negotiation tool for high-altitude operations. To facilitate negotiation, this tool incorporates a bilateral negotiation model with an algorithm to assess conflict risks and generate new flight trajectories with a given flight path deviation. This tool allows users to make decisions during negotiation manually and automatically while enforcing the needed constraints for negotiation to be successful. Operators can make decisions at every step while they interact with each other on separate devices. To conduct sensitivity analysis, a mechanism that automates human inputs to the user interface is also developed for this web-based negotiation tool, such that fast-time simulations can be constructed and used to explore various scenarios to gain insights into this web-based negotiation model. Using this tool, a study was conducted to evaluate the impact of different negotiation strategies, vehicle types, vehicle crossing angles, and operator response times during the negotiations on metrics such as total negotiation completion time, number of negotiation rounds, and extra flight distance to avoid the conflict due to negotiation, compared to ones without negotiation. The results suggest that operators benefit from using negotiated flight paths with quick response times, across various crossing angles and vehicle types. Various Negotiation Strategies are investigated to simulate the behaviors associated with different types of negotiations. The findings demonstrate that, in comparison to the conventional method where a single operator assumes full responsibility, negotiation-based strategic deconfliction reduces the total extra flight distance by an average of 24% - 27%. On an individual basis, each operator may be able to save an average of 65% of their extra flight distance.

Upper Class E Traffic Management (ETM)↗
NASA NTRS1990

Simple analyses of paths through windshears and downdrafts

Quasi-steady analysis and energy-state approximation are employed to study flight paths through windshears and downdrafts. Takeoff flight is mainly considerd while landing flight is briefly discussed. The relation between angle of attack and airspeed is found to be almost independent of horizontal wind and slightly dependent on vertical wind. In slowly-varying windshears and/or downdrafts, quasi-steady flight can be achieved by flying an aircraft at a lower than nominal climb rate; this will avoid stall. In severe windshears and/or downdrafts, energy-state approximation indicates that descending paths save more energy and provide higher survival capability.

Zhao, Yiyuan↗
NASA NTRS1973

Experimental landings in a spoiler-equipped light aircraft.

This report presents the results of a flight test program to determine the effects on landings of wide variations in approach path angle and approach airspeed for different kinds of piloting technique. Over 400 landings were made at approach speeds from 60 to 120 mph and approach path angles from 3 to 18 deg. Several variations of pilot technique involving different operations of the throttle/spoiler control were investigated. It is shown that very large ranges of airspeed and approach path angle can be accommodated with rather moderate penalties in landing distance and difficulty. With the spoiler-equipped aircraft, the best approach speeds are considerably higher than would be usable without spoilers, and approach path angles can be used which are far beyond those normally possible without spoilers.

Seckel, E.↗
NASA NTRS1960

Analytical Investigation of the Dynamic Behavior of a Nonlifting Manned Reentry Vehicle

An analytic investigation was made of the dynamic behavior of a nonlifting manned reentry vehicle as it descended through the atmosphere. The investigation included the effects of variations in the aerodynamic stability derivatives, the spin rate, reentry angle, and velocity. The effect of geostrophic winds and of employing a drogue parachute for stability purposes were also investigated. It was found that for the portion of the flight above a Mach number of 1 a moderate amount of negative damping could be tolerated but below a Mach number of 1 good damping is necessary. The low-speed stability could be improved by employing a drogue parachute. The effectiveness of the drogue parachute was increased when attached around the periphery of the rear of the vehicle rather than at the center. Neither moderate amounts of spin or the geostrophic winds had appreciable effects on the stability of the vehicle. The geostrophic winds and the reentry angle or velocity all showed important effects on the range covered by the reentry flight path.

Lichtenstein, Jacob H.↗
NASA NTRS1973

A fixed-base simulation study of two STOL aircraft flying curved, descending instrument approach paths

A real-time, fixed-base simulation study has been conducted to determine the curved, descending approach paths (within passenger-comfort limits) that would be acceptable to pilots, the flight-director-system logic requirements for curved-flight-path guidance, and the paths which can be flown within proposed microwave landing system (MLS) coverage angles. Two STOL aircraft configurations were used in the study. Generally, no differences in the results between the two STOL configurations were found. The investigation showed that paths with a 1828.8 meter turn radius and a 1828.8 meter final-approach distance were acceptable without winds and with winds up to at least 15 knots for airspeeds from 75 to 100 knots. The altitude at roll-out from the final turn determined which final-approach distances were acceptable. Pilots preferred to have an initial straight leg of about 1 n. mi. after MLS guidance acquisition before turn intercept. The size of the azimuth coverage angle necessary to meet passenger and pilot criteria depends on the size of the turn angle: plus or minus 60 deg was adequate to cover all paths execpt ones with a 180 deg turn.

Benner, M. S.↗
NASA NTRS1983

Crash tests of three identical low-wing single-engine airplane

Three identical four place, low wing single engine airplane specimens with nominal masses of 1043 kg were crash tested under controlled free flight conditions. The tests were conducted at the same nominal velocity of 25 m/sec along the flight path. Two airplanes were crashed on a concrete surface (at 10 and 30 deg pitch angles), and one was crashed on soil (at a -30 deg pitch angle). The three tests revealed that the specimen in the -30 deg test on soil sustained massive structural damage in the engine compartment and fire wall. Also, the highest longitudinal cabin floor accelerations occurred in this test. Severe damage, but of lesser magnitude, occurred in the -30 deg test on concrete. The highest normal cabin floor accelerations occurred in this test. The least structural damage and lowest accelerations occurred in the 10 deg test on concrete.

Castle, C. B.↗
NASA NTRS1941

Velocity gained and altitude lost in recoveries from inclined flight paths

A series of charts is given showing the variation of the velocity gained and the altitude lost in dive pullouts with the initial indicated air speed and the dive angle. The effects of the maximum load factor, the drag parameter K, the initial altitude, and the type of recovery on the velocity gained and the altitude lost are also considered. The results were obtained from a step-by-step solution of the equations of motion in which mean values of the air density and the airplane drag coefficient were used. The load-factor variation with time is arbitrarily specified in various ways to simulate pull-out procedures, some of which might be encountered in flight.

Pearson, H A↗
NASA NTRS1995

Conceptual Design of a Tiltrotor Transport Flight Deck

A tiltrotor transport has considerable potential as a regional transport, increasing the air transportation system capacity by off-loading conventional runways. Such an aircraft will have a flight deck suited to its air transportation task and adapted to unique urban vertiport operating requirements. Such operations are likely to involve steep, slow instrument approaches for vertical and extremely short rolling take-offs and landings. While much of a tiltrotor transport's operations will be in common with commercial fixed-wing operations, terminal area operations will impose alternative flight deck design solutions. Control systems, displays and guidance, and control inceptors must be tailored to both routine and emergency vertical flight operations. This paper will survey recent experience with flight deck design elements suitable to a tiltrotor transport and will propose a conceptual cockpit design for such an aircraft. A series of piloted simulations using the NASA Ames Vertical Motion Simulator have investigated cockpit design elements and operating requirements for tiltrotor transports operating into urban vertiports. These experiments have identified the need for a flight director or equivalent display guidance for steep final approaches. A flight path vector display format has proven successful for guiding tiltrotor transport terminal area operations. Experience with a Head-Up Display points to the need for a bottom-mounted display device to maximize its utility on steep final approach paths. Configuration control (flap setting and nacelle angle) requires appropriate augmentation and tailoring for civil transport operations, flown to an airline transport pilot instrument flight rules (ATP-IFR) standard. The simulation experiments also identified one thrust control lever geometry as inappropriate to the task and found at least acceptable results with the vertical thrust control lever of the XV-15. In addition to the thrust controller, the attitude control of a tiltrotor transport may be effected through an inceptor other than the current center sticks in the XV-15 and V-22. Simulation and flight investigations of side-stick control inceptors for rotorcraft, augmented by a 1985 flight test of a side-stick controller in the XV-15 suggest the potential of such a device in a transport cockpit.

Decker, William A.↗
NASA NTRS1978

Airborne antenna coverage requirements for the TCV B-737 aircraft

The airborne antenna line of sight look angle requirement for operation with a Microwave Landing System (MLS) was studied. The required azimuth and elevation line of sight look angles from an antenna located on an aircraft to three ground based antenna sites at the Wallops Flight Center (FPS-16 radar, MLS aximuth, and MLS elevation) as the aircraft follows specific approach paths selected as representative of MLS operations at the Denver, Colorado, terminal area are presented. These required azimuth and elevation look angles may be interpreted as basic design requirements for antenna of the TCV B-737 airplane for MLS operations along these selected approach paths.

Southall, W. A., Jr.↗
NASA NTRS1992

Target pitch angle for the microburst escape maneuver

Recovery performance of a commuter-type aircraft in a microburst encounter is studied using a constant-pitch-attitude strategy and flight path optimization. Results obtained indicate that the pitch attitude which maximized climb rate in a wind shear condition is strongly dependent on whether the aircraft is subjected to a horizontal shear or a downdraft. The pitch attitude which maximizes ground clearance depends on the altitude of the encounter, the strength of the microburst, and the initial position of the aircraft with respect to the downburst core. Best results are obtained at relatively low target pitch angles, in severe wind shear encounters at very low altitudes. A technique for maximizing ground clearance involves maintaining a low pitch attitude early in the encounter, followed by a gradual pitch-up that ceases when the wind shear has been excited.

Mulgund, Sandeep S.↗