Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Graphite fluoride as a solid lubricant in a polyimide binder

Polyimide resin (PI) was shown to be a suitable binder material for the solid lubricant graphite fluoride, (CF(1.1))n. Comparisons were made to similar tests using PI-bonded MOS2 films, graphite fluoride rubbed films, and MOS2 rubbed films. The results showed that, at any one specific temperature between 25 and 400 C, the wear life of PI-bonded graphite fluoride films exceeded those of the other three films by at least a factor of 2 and by as much as a factor of 60. Minimum friction coefficients for the PI-bonded films were 0.08 for graphite fluoride and 0.04 for MOS2. The rider wear rates for the two PI-bonded films at 25 C were nearly equal.

Fusaro, R. L.↗
NASA NTRS1972

Boundary layer loss sensitivity study using a modified ICRPG turbulent boundary layer computer program

Modifications of the turbulent boundary layer (TBL) computer program refer to a more accurate representation of boundary layer edge conditions, internal calculation of the Prandtl number, a changed friction coefficient relationship, and computation of the performance degradation. Important input parameters of the modified TBL program such as wall temperature distribution, Prandtl number, Stanton number, and velocity profile exponent were changed and the individual effects on significant boundary layer parameters, heat transfer, and performance degradation are described.

Omori, S.↗
NASA NTRS1972

The turbulent boundary layer on a porous plate: An experimental study of the fluid mechanics for adverse free stream pressure gradients

An experimental investigation of transpired turbulent boundary layers in zero and adverse pressure gradients has been carried out. Profiles of: (1) the mean velocity, (2) the three intensities of the turbulent fluctuations, and (3) the Reynolds stress were obtained by hot-wire anemometry. The friction coefficients were measured by using an integrated form of the boundary layer equation to extrapolate the measured shear stress profiles to the wall.

Anderson, P. S.↗
NASA NTRS1972

Boundary lubrication of formulated C-ether in air to 300 deg C. 1: Phosphorus ester additives

Friction and wear measurements were made on CVM M-50 steel lubricated with three C-ether (modified polyphenyl ether) formulations in dry and wet air. Results were compared to those obtained with a formulated Type 2 ester and the C-ether base fluid. A ball-on-disk sliding friction apparatus was used. Experimental conditions were a 1-kilogram load, a 17-meter-perminute (100-rpm) surface speed, and a 25 to 300 C (77 to 572 F) disk temperature range. The C-ether base fluid and the three formulated C-ether fluids yielded lower wear than the Type 2 ester over the entire temperature range. All C-ether fluids exhibited slightly higher friction coefficients than the ester from 150 to 300 C (302 to 572 F) and similar values from 25 to 150 C (77 to 302 F). In general, lower wear rates were observed with the C-ethers when tested in wet air as compared to a dry air atmosphere.

Jones, W. R., Jr.↗
NASA NTRS1972

Dynamic friction and wear of a solid film lubricant during radiation exposure in a nuclear reactor

The effect of nuclear reactor radiation on the performance of a solid film lubricant was studied. The film consisted of molybdenum disulfide and graphite in a sodium silicate binder. Radiation levels of fast neutrons (E or = 1 MeV) were fluxed up to 3.5 times 10 to the 12th power n/sq cm-sec (intensity) and fluences up to 2 times 10 to the 18th power n/sq cm (total exposure). Coating wear lives were much shorter and friction coefficients higher in a high flux region of the reactor than in a low flux region. The amount of total exposure did not affect lubrication behavior as severely as the radiation intensity during sliding.

Jacobson, T. P.↗
NASA NTRS1972

Graphite fiber polyimide composites for spherical bearings to 340 C (650 F)

Journal bearings with self-alining spherical elements of graphite-fiber-reinforced-polyimide composites were tested from 24 to 340 C (75 to 650 F) at unit loads up to 3.5 times 10 to the 7th power N/sq m (5000 psi). The journal oscillated in the cylindrical bore of the composite element + or - 15 deg at 1 hertz. Outer races and journals were metal hardened of Rockwell C-32 and finished to 10 to the minus 7th power m. A 45 wt. percent graphite-fiber composite gave low friction (0.08 to 0.13), low wear, and almost no plastic deformation under any of the test conditions. Composites with 15 and 25 wt. percent graphite fiber failed by plastic deformation at 315 C (600 F) and 3.5 times 10 to the 7th power N/sq m (5000 psi). A composite with 60 wt. percent graphite fiber failed by brittle fracture under the same conditions, but had very low friction coefficients (0.05 to 0.10) and may be a good bearing material at lighter loads.

Sliney, H. E.↗
NASA NTRS1972

An analysis of the relaxation of laminar boundary layer on a flat plate after passage of an interface with application to expansion-tube flows

The relaxation of the accelerating-gas boundary layer to the test-gas boundary layer over a flat plate in an expansion tube is analyzed. Several combinations of test gas and acceleration gas are considered. The problem is treated in two conically similar limits: (1) when the time lag between the arrival of the shock and the interface at the leading edge of the plate is very large, and (2) when this lag is negligible. The time-dependent laminar-boundary-layer equations of a binary mixture of perfect gases are taken as the flow-governing equations. This coupled set of differential equations, written in terms of the Lam-Crocco variables, has been solved by a line-relaxation finite-difference techniques. The results presented include the Stanton number and the local skin-friction coefficient as functions of shock Mach number and the nondimensional distance-time variable. The results indicate that more than 95 percent of the test-gas boundary layer exists over a length, measured from the leading edge of the plate, equal to about three-tenths of the distance traversed by the interface in the free stream.

Gupta, R. N.↗
NASA NTRS1973

Boundary lubrication of formulated C-ethers in air to 300 C. 2: Organic acid additives

Friction and wear measurements were made on CVM M-50 steel lubricated with three C-ether (modified polyphenyl ether) formulations in dry and moist air. Results were compared to those obtained with a formulated Type 2 ester and the C-ether base fluid. A ball-on-disk sliding friction apparatus was used. Experimental conditions were a 1-kilogram load, a 17-meter/minute surface speed, and a 25 to 300 C (77 to 572 F) disk temperature range. The three C-ether formulations yielded better boundary lubricating characteristics than the Type 2 ester under most test conditions. All C-ether formulations exhibited higher friction coefficients than the ester from 150 to 300 C (302 to 572 F) and similar or lower values from 25 to 150 C (77 to 302 F).

Jones, W. R., Jr.↗
NASA NTRS1973

Some effects of grooved runway configurations on aircraft tire braking traction under flooded runway conditions

An experimental investigation was conducted to study the effect of grooved runway configurations on aircraft tire braking traction on flooded runway surfaces. The investigation was performed, utilizing size 49 x 17, type VII, aircraft tires with an inflation pressure of 170 lb per square inch at ground speeds up to approximately 120 knots. The results of this investigation indicate that when the runway is flooded, grooved surfaces provide better braking traction than an ungrooved surface and, in general, the level of braking traction was found to improve as the tire bearing pressure was increased because of an increase in the groove area of either the surface or the tire tread. Rounding the groove edges tended to degrade the tire braking capability from that developed on the same groove configuration with sharp edges. Results also indicate that braking friction coefficients for the test tires and runway surfaces decreased as ground speed was increased because of the hydroplaning effects.

Byrdsong, T. A.↗
NASA NTRS1973

Cornering characteristics of a 40 by 14-16 type 7 aircraft tire and a comparison with characteristics of a C40 by 14-21 cantilever aircraft tire

An investigation was conducted at the Langley aircraft landing loads and traction facility to determine the cornering characteristics of a 40 x 14-16 type VII aircraft tire. These characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained for the tire operating on dry, damp and flooded runway surfaces over a range of yaw angles from 0 deg to 20 deg and at ground speeds from 5 to 100 knots, both with and without braking. The results of this investigation indicated that the cornering capability of the 40 x 14-16 type VII aircraft tire is degraded by high ground speeds, thin-film lubrication and tire hydroplaning effects on the wet surfaces, and brake torque. The cornering capability is greatly diminished when locked-wheel skids are encountered.

Tanner, J. A.↗
NASA NTRS1973

Comparison of predicted and measured low-speed performance of two 51 centimeter-diameter inlets at incidence angle

Theoretical and experimental internal flow characteristics of two 51-cm-diameter inlets are compared. Theoretical flow characteristics along the inlet surface were obtained from an axisymmetric potential flow and boundary layer analysis. The experimental data were obtained from low-speed tests of a high-bypass-ratio turbofan engine simulator. Comparisons between calculated internal surface pressure distributions and experimental data are presented for a free-system velocity of 45 m/sec and for incidence angles from 0 deg to 50 deg. Analysis of boundary layer separation on the inlet lip at incidence angle is the major emphasis of this report. Theoretical boundary layer shape factors, skin friction coefficients, and velocity profiles in the boundary layer are presented, along with the location of the transition region. Theoretical and experimental separation locations are also discussed.

Albers, J. A.↗
NASA NTRS1973

Friction behavior of glass and metals in contact with glass in various environments

Sliding friction experiments have been conducted for heat-resistant glass and metals in contact with glass. These experiments were conducted in various environments including vacuum, moist air, dry air, octane, and stearic acid in hexadecane. Glass exhibited a higher friction force in moist air than it did in vacuum when in sliding contact with itself. The metals, aluminum, iron, and gold, all exhibited the same friction coefficient when sliding on glass in vacuum as glass sliding on glass. Gold-to-glass contacts were extremely sensitive to the environment despite the relative chemical inertness of gold.

Buckley, D. H.↗
NASA NTRS1974

Comparison of theoretical and experimental boundary-layer development in a Mach 2.5 mixed-compression inlet

An analytical investigation was made of the boundary layer flow in an axisymmetric Mach 2.5 mixed compression inlet, and the results were compared with experimental measurements. The inlet tests were conducted in the Lewis 10- by 10-foot supersonic wind tunnel at a unit Reynolds number of 8.2 million/m. The inlet incorporated porous bleed regions for boundary layer control, and the effect of this bleed was taken into account in the analysis. The experimental boundary layer data were analyzed by using similarity laws from which the skin friction coefficient was obtained. The boundary layer analysis included predictions of laminar and turbulent boundary layer growth, transition, and the effects of the shock boundary layer interactions. In addition, the surface static pressures were compared with those obtained from an inviscid characteristics program. The results of investigation showed that the analytical techniques gave satisfactory predictions of the boundary layer flow except in regions that were badly distorted by the terminal shock.

Hingst, W. R.↗
NASA NTRS1974

Effect of strain hardening on friction behavior of iron lubricated with benzyl structures

Sliding friction experiments were conducted with iron, copper, and aluminum in contact with iron in various states of strain. The surfaces were examined in dry sliding and with various benzyl compounds applied as lubricants. Friction experiments were conducted with a hemispherical rider contacting a flat disk at loads of from 50 to 600 grams with a sliding speed of 0.15 cm/min. Results indicate that straining increases friction for dry sliding and for surfaces lubricated with certain benzyl structures such as dibenzyl disulfide. With other benzyl compounds (e.g., benzyl formate), friction coefficients are lower for strained than for annealed iron.

Buckley, D. H.↗
NASA NTRS1974

Computer program for calculation of real gas turbulent boundary layers with variable edge entropy

A user's manual for a computer program which calculates real gas turbulent boundary layers with variable edge entropy on a blunt cone or flat plate at zero angle of attack is presented. An integral method is used. The method includes the effect of real gas in thermodynamic equilibrium and variable edge entropy. A modified Crocco enthalpy velocity relationship is used for the enthalpy profiles and an empirical correlation of the N-power law profile is used for the velocity profile. The skin-friction-coefficient expressions of Spalding and Chi and Van Driest are used in the solution of the momentum equation and in the heat-transfer predictions that use several modified forms of Reynolds analogy.

Boney, L. R.↗
NASA NTRS1973

The use of a digital computer for investigation of the dynamic characteristics of a man while pressing vertically downward with the straight arm on the handle of a vibrator (instrument)

The dynamic characteristics of a man were investigated by the resonance method, by means of recordings of the amplitude-frequency characteristics of a vibrator straight arm human body system on a standard automatic recorder. Experiments were carried out with a specially constructed vibrator, the moving system of which was fastened to a bronze suspension with small losses. Vibrations of the handle, fastened to the moving system, were recorded with an accelerometer. The mass of the moving system m, rigidity of the suspension k and friction coefficient r of the vibrator (calibration) were determined by exact formulas.

Zazhivikhina, A. I.↗
NASA NTRS1974

Experimental investigation of the braking and cornering characteristics of 30 x 11.5-14.5, type 8, aircraft tires with different tread patterns

An investigation was conducted at the aircraft landing loads and traction facility to study the braking and cornering characteristics, including the drag-force and cornering-force friction coefficients, of 30 by 11.5-14.5, type VIII aircraft tires with five different tread patterns. Test data were obtained on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 12 deg at ground speeds from 5 knots to 100 knots. The results of this investigation indicate that a tread pattern consisting of transverse cuts across the entire width of the tread slightly improved the tire traction performance on wet surfaces. The braking and cornering capability of the tires was degraded by thin-film lubrication and tire hydroplaning effects on the wet runway surfaces. The braking capability of the tires decreased when the yaw angle was increased.

Dreher, R. C.↗
NASA NTRS1974

Viscous reacting flows with wall slip and catalysis applied to spheres in arc jets and flight

The influence of wall slip and catalytic atom-recombination on the flow field and wall heat flux are calculated for high altitude flight and arc jet flow conditions. Boundary equations, which include velocity slip, temperature jump, and wall catalytic atom recombination, are coupled to the viscous reacting multicomponent Navier-Stokes equations. These equations are solved using a time-dependent finite difference technique applied to spheres in an arc jet flow (Reynolds number of 550) and a high altitude flight case representative of the Space Shuttle Orbiter (Reynolds number of 450). The results indicate that catalysis strongly influences the temperature jump, but not the velocity slip. Slip increases the atom fraction and temperature at both the wall and the flow field. Likewise, the shock stand-off distance, the wall heat flux, and friction coefficient are increased over the nonslip cases. The reacting gas calculations confirm the chemically frozen nature of the shock layer in arc jet flows.

Scott, C. D.↗