Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel assembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Research Symposium II

Contents include the following: High power density motors. The training process of the organization development and training office. Modeling and analysis of a regenerative fuel cell propulsion system for a high altitude long endurance. Increasing the thermal stability of aluminum titanate for solid oxide mJEL cell anodes. Microstructural evaluation of forging parameters for superalloy disks. Epoxy adgesives for stator magnet assembly in stirling radioisotope generator. Nickel-Hydrogen and lithium ion space batteries. Statistical and prediction modeling of the Ka band using experimental results from ACTS propagation terminals at 20.185 and 27.505 GHz.

Source record↗
NASA NTRS2011

Design of Multilayer Insulation for the Multipurpose Hydrogen Test Bed

Multilayer insulation (MLI) is a critical component for future, long term space missions. These missions will require the storage of cryogenic fuels for extended periods of time with little to no boil-off and MLI is vital due to its exceptional radiation shielding properties. Several MLI test articles were designed and fabricated which explored methods of assembling and connecting blankets, yielding results for evaluation. Insight gained, along with previous design experience, will be used in the design of the replacement blanket for the Multipurpose Hydrogen Test Bed (MHTB), which is slated for upcoming tests. Future design considerations are discussed which include mechanical testing to determine robustness of such a system, as well as cryostat testing of samples to give insight to the loss of thermal performance of sewn panels in comparison to the highly efficient, albeit laborious application of the original MHTB blanket.

Marlow, Weston A.↗
NASA NTRS1998

The Recovery of TOMS-EP

On December 13th 1998, the Total Ozone Mapping Spectrometer - Earth Probe (TOMS-EP) spacecraft experienced a Single Event Upset which caused the system to reconfigure and enter a Safe Mode. This incident occurred two and a half years after the launch of the spacecraft which was designed for a two year life. A combination of factors, including changes in component behavior due to age and extended use, very unfortunate initial conditions and the safe mode processing logic prevented the spacecraft from entering its nominal long term storage mode. The spacecraft remained in a high fuel consumption mode designed for temporary use. By the time the onboard fuel was exhausted, the spacecraft was Sun pointing in a high rate flat spin. Although the uncontrolled spacecraft was initially in a power and thermal safe orientation, it would not stay in this state indefinitely due to a slow precession of its momentum vector. A recovery team was immediately assembled to determine if there was time to develop a method of despinning the vehicle and return it to normal science data collection. A three stage plan was developed that used the onboard magnetic torque rods as actuators. The first stage was designed to reduce the high spin rate to within the linear range of the gyros. The second stage transitioned the spacecraft from sun pointing to orbit reference pointing. The final stage returned the spacecraft to normal science operation. The entire recovery scenario was simulated with a wide range of initial conditions to establish the expected behavior. The recovery sequence was started on December 28th 1998 and completed by December 31st. TOMS-EP was successfully returned to science operations by the beginning of 1999. This paper describes the TOMS-EP Safe Mode design and the factors which led to the spacecraft anomaly and loss of fuel. The recovery and simulation efforts are described. Flight data are presented which show the performance of the spacecraft during its return to science. Finally, lessons learned are presented.

Robertson, Brent↗
NASA NTRS2007

Analytical Approach for Estimating Preliminary Mass of ARES I Crew Launch Vehicle Upper Stage Structural Components

In January 2004, President Bush gave the National Aeronautics and Space Administration (NASA) a vision for Space Exploration by setting our sight on a bold new path to go back to the Moon, then to Mars and beyond. In response to this vision, NASA started the Constellation Program, which is a new exploration launch vehicle program. The primary mission for the Constellation Program is to carry out a series of human expeditions ranging from Low Earth Orbit to the surface of Mars and beyond for the purposes of conducting human exploration of space, as specified by the Vision for Space Exploration (VSE). The intent is that the information and technology developed by this program will provide the foundation for broader exploration activities as our operational experience grows. The ARES I Crew Launch Vehicle (CLV) has been designated as the launch vehicle that will be developed as a "first step" to facilitate the aforementioned human expeditions. The CLV Project is broken into four major elements: First Stage, Upper Stage Engine, Upper Stage (US), and the Crew Exploration Vehicle (CEV). NASA's Marshall Space Flight Center (MSFC) is responsible for the design of the CLV and has the prime responsibility to design the upper stage of the vehicle. The US is the second propulsive stage of the CLV and provides CEV insertion into low Earth orbit (LEO) after separation from the First Stage of the Crew Launch Vehicle. The fully integrated Upper Stage is a mix of modified existing heritage hardware (J-2X Engine) and new development (primary structure, subsystems, and avionics). The Upper Stage assembly is a structurally stabilized cylindrical structure, which is powered by a single J-2X engine which is developed as a separate Element of the CLV. The primary structure includes the load bearing liquid hydrogen (LH2) and liquid oxygen (LOX) propellant tanks, a Forward Skirt, the Intertank structure, the Aft Skirt and the Thrust Structure. A Systems Tunnel, which carries fluid and electrical power functions to other Elements of the CLV, is included as secondary structure. The MSFC has an overall responsibility for the integrated US element as well as structural design an thermal control of the fuel tanks, intertank, interstage, avionics, main propulsion system, Reaction Control System (RCS) for both the Upper Stage and the First Stage. MSFC's Spacecraft and Vehicle Department, Structural and Analysis Design Division is developing a set of predicted mass of these elements. This paper details the methodology, criterion and tools used for the preliminary mass predictions of the upper stage structural assembly components. In general, weight of the cylindrical barrel sections are estimated using the commercial code Hypersizer, whereas, weight of the domes are developed using classical solutions. HyperSizer is software that performs automated structural analysis and sizing optimization based on aerospace methods for strength, stability, and stiffness. Analysis methods range from closed form, traditional hand calculations repeated every day in industry to more advanced panel buckling algorithms. Margin-of-safety reporting for every potential failure provides the engineer with a powerful insight into the structural problem. Optimization capabilities include finding minimum weight panel or beam concepts, material selections, cross sectional dimensions, thicknesses, and lay-ups from a library of 40 different stiffened and sandwich designs and a database of composite, metallic, honeycomb, and foam materials. Multiple different concepts (orthogrid, isogrid, and skin stiffener) were run for multiple loading combinations of ascent design load with and with out tank pressure as well as proof pressure condition. Subsequently, selected optimized concept obtained from Hypersizer runs was translated into a computer aid design (CAD) model to account for the wall thickness tolerance, weld land etc for developing the most probable weight of the components. The flow diram summarizes the analysis steps used in developing these predicted mass.

Aggarwal, Pravin↗
NASA NTRS1975

Register of specialized sources for information on selected fuels and oxidizers

Thirty-eight (38) organizations are listed and described that catalog and file information in their data systems on fuel and oxidizers. The fuels include hydrogen, methane and hydrazine-type fuels; the oxidizers include oxygen, fluorine, flox, nitrogen tetroxide and ozone. The type of available information covers thermophysical properties, propellant systems, propellant fires-control-extinguishment, propellant explosions, propellant combustion, propellant safety, and fluorine chemistry. These organizations have assembled and collated their information so that it will be useful in the solution of engineering problems.

Ludtke, P. R.↗
NASA NTRS1982

Progress in ceramic component fabrication technology

Net shape techniques have been used in the production of rotating and static vehicular engine high-temperature components composed of sintered Alpha-SiC (SASC). Injection-molded rotors have been cold spin tested, as well as a slip-cast combustor assembly hot rig. SASC pistons and cylinder liners have also been constructed for an opposed piston, two-cycle diesel test rig while test results are presented. An uncooled, minimum-friction internal combustion engine with multi-fuel capability due to its elevated combustion temperatures appears to be achievable in the near term by means of SASC techniques. The flexural strength of SASC at 1500 C is 446 MPa, identical to that at room temperature, and excellent strength retention has been demonstrated after 3500 hours of cyclic exposure.

Storm, R. S.↗
NASA NTRS2015

Additively Manufactured Main Fuel Valve Housing

Selective Laser Melting (SLM) was utilized to fabricate a liquid hydrogen valve housing typical of those found in rocket engines and main propulsion systems. The SLM process allowed for a valve geometry that would be difficult, if not impossible to fabricate by traditional means. Several valve bodies were built by different SLM suppliers and assembled with valve internals. The assemblies were then tested with liquid nitrogen and operated as desired. One unit was also burst tested and sectioned for materials analysis. The design, test results, and planned testing are presented herein.

Eddleman, David↗
NASA NTRS1970

Manned space programs accident/incident summaries (1963 - 1969)

This summary is a compilation of 508 mishaps assembled from company and NASA records which cover several years of manned space flight activity. The purpose is to provide information to be applied towards accident prevention. The accident/incident summaries are categorized by the following ten systems: cryogenic; electrical; facility/GSE; fuel and propellant; life support; ordnance; pressure; propulsion; structural; and transport/handling. Each accident/incident summary has been summarized by description, cause and recommended preventive action.

Source record↗
NASA NTRS1973

Mini-Brayton heat source assembly design study. Volume 1: Space shuttle mission

Conceptual design definitions of a heat source assembly for use in nominal 500 watt electrical (W(e)) 1200 W(e)and 2000 W(e) mini-Brayton isotope power systems are reported. The HSA is an independent package which maintains thermal and nuclear control of an isotope fueled heat source and transfers the thermal energy to a Brayton rotating unit turbine-alternator-compressor power conversion unit.

Source record↗
NASA NTRS1981

Army/NASA small turboshaft engine digital controls research program

The emphasis of a program to conduct digital controls research for small turboshaft engines is on engine test evaluation of advanced control logic using a flexible microprocessor based digital control system designed specifically for research on advanced control logic. Control software is stored in programmable memory. New control algorithms may be stored in a floppy disk and loaded directly into memory. This feature facilitates comparative evaluation of different advanced control modes. The central processor in the digital control is an Intel 8086 16 bit microprocessor. Control software is programmed in assembly language. Software checkout is accomplished prior to engine test by connecting the digital control to a real time hybrid computer simulation of the engine. The engine currently installed in the facility has a hydromechanical control modified to allow electrohydraulic fuel metering and VG actuation by the digital control. Simulation results are presented which show that the modern control reduces the transient rotor speed droop caused by unanticipated load changes such as cyclic pitch or wind gust transients.

Sellers, J. F.↗
NASA NTRS1986

Modified US Army U-8F ground vibration test

The Dryden Flight Research Facility of NASA Ames Research Center conducted a ground vibration test on a modified U.S. Army U-8F airplane. Modifications included new engines, propellers, and engine-mounted truss assemblies. The ground vibration test was conducted using sine dwell, single-point random, and impact excitations. The test was performed to determine modal frequencies, mode shapes, and structural damping coefficients of the airframe and propeller with full and empty fuel tanks. The data presented include frequency response plots, rigid-body and structural modal frequencies, and mode shapes.

Kehoe, M. W.↗
NASA NTRS2019

A Single Stage to Orbit Design for a Hybrid Mars Ascent

A Single Stage to Orbit (SSTO) hybrid propulsion system has been previously studied as an option for a conceptual Mars Ascent Vehicle (MAV). The hybrid motor uses a wax-based fuel developed specifically for this application, so it can take advantage of a single port design. The oxidizer is Mixed Oxides of Nitrogen (MON-25). Higher Nitric Oxide concentrations have been discussed in the past, however, the lower temperature capability is no longer needed. The MAV Payload Assembly (MPA), which would house the Orbiting Sample (OS) has changed substantially from previous iterations and has become more compact. Benefits of the hybrid option include its predicted low temperature behavior, high performance and ability to restart (enabling the SSTO). However, the hybrid technology remained at a relatively low Technology Readiness Level (TRL). In an attempt to increase the TRL, a technology development program has been underway for the past four years. The results of the technology development program are now being incorporated to an updated concept for a hybrid Mars Ascent Vehicle, with the eventual goal of informing a hybrid propulsion design that closes under the guidelines currently envisioned for a potential Mars Sample Return campaign. This paper focuses on the hybrid propulsion system design and the preliminary results from the first part of the FY19 technology development program (October 2018 to July 2019) and includes some results from a Preliminary Architecture Assessment (PAA) study. In the PAA, experts from all relevant subsystems (propulsion, avionics, GN&C, structures, thermal, etc.) are brought together to determine an updated vehicle design. The PAA is being run out of Marshall Space Flight Center (MSFC) in coordination with the Mars Sample Return study lead by the Jet Propulsion Laboratory (JPL). Currently, it is thought that the Mars Ascent Vehicle would be housed in a Sample Retrieval Lander (SRL), along with a fetch rover. The SRL would be responsible for several crucial functions on the MAV including heating, erection and providing the ignition signal. This paper will also outline the future testing and path forward through the rest of the fiscal year. This includes full scale testing at Whittinghill Aerospace, hypergolic additive testing at Purdue, evaluation of adding hypergolic additives to a full-scale grain. A hybrid fuel formulation has been updated with a reduced regression rate, which again was developed by Space Propulsion Group. This design will be used to determine the benefits of a hybrid versus solid propulsion system for a MAV, as they fit into the larger vision for a potential Mars Sample Return campaign.

Story, George↗
NASA NTRS1988

NASA/industry advanced turboprop technology program

Experimental and analytical effort shows that use of advanced turboprop (propfan) propulsion instead of conventional turbofans in the older narrow-body airline fleet could reduce fuel consumption for this type of aircraft by up to 50 percent. The NASA Advanced Turboprop (ATP) program was formulated to address the key technologies required for these thin, swept-blade propeller concepts. A NASA, industry, and university team was assembled to develop and validate applicable design codes and prove by ground and flight test the viability of these propeller concepts. Some of the history of the ATP project, an overview of some of the issues, and a summary of the technology developed to make advanced propellers viable in the high-subsonic cruise speed application are presented. The ATP program was awarded the prestigious Robert J. Collier Trophy for the greatest achievement in aeronautics and astronautics in America in 1987.

Ziemianski, Joseph A.↗
NASA NTRS1988

NASA/industry advanced turboprop technology program

Experimental and analytical effort shows that use of advanced turboprop (propfan) propulsion instead of conventional turbofans in the older narrow-body airline fleet could reduce fuel consumption for this type of aircraft by up to 50 percent. The NASA Advanced Turboprop (ATP) program was formulated to address the key technologies required for these thin, swept-blade propeller concepts. A NASA, industry, and university team was assembled to develop and validate applicable design codes and prove by ground and flight test the viability of these propeller concepts. Some of the history of the ATP Project, an overview of some of the issues, and a summary of the technology developed to make advanced propellers viable in the high-subsonic cruise speed application are presented. The ATP program was awarded the prestigious Robert J. Collier Trophy for the greatest achievement in aeronautics and astronautics in America in 1987.

Ziemianski, Joseph A.↗
NASA NTRS2002

FSW Implementation on the Space Shuttle's External Tank

The Friction Stir Welding process developed by The Welding Institute (TWI) has found application throughout the transportation industry. This technique has proven to be a viable joining process for aluminum alloys, producing virtually defect free welds with improved mechanical properties as compared to conventional fusion welding. Lockheed Martin Space Systems - Michoud Operations has been developing this technology for application on aluminum 2219 and 2195 cryogenic tankage since 1995. This effort will come to fruition with implementation on the longitudinal welds of the External Fuel Tank (ET) of the Shuttle. To this end, sub-and full-scale demonstration programs coupled with process development and optimization have been complete. Full size ET tool has been designed, fabricated and are being installed at the Michoud Assembly Facility. Upon completion of the tooling certification and materials allowables testing, production will commence. This implementation will result in increased reliability and safety of flight for the Shuttle.

Hartley, Paula J.↗
NASA NTRS2004

Use of Strain Measurements from Acoustic Bench Tests of the Battleship Flowliner Test Articles To Link Analytical Model Results to In-Service Resonant Response

The paper will discuss practical and analytical findings of a test program conducted to assist engineers in determining which analytical strain fields are most appropriate to describe the crack initiating and crack propagating stresses in thin walled cylindrical hardware that serves as part of the Space Shuttle Main Engine's fuel system. In service the hardware is excited by fluctuating dynamic pressures in a cryogenic fuel that arise from turbulent flow/pump cavitation. A bench test using a simplified system was conducted using acoustic energy in air to excite the test articles. Strain measurements were used to reveal response characteristics of two Flowliner test articles that are assembled as a pair when installed in the engine feed system.

Frady, Greg↗
NASA NTRS2012

Near Earth Asteroid Human Mission Possibilities Using Nuclear Thermal Rocket (NTR) Propulsion

The NTR is a proven technology that generates high thrust and has a specific impulse (Isp (is) approximately 900 s) twice that of today's best chemical rockets. During the Rover and NERVA (Nuclear Engine for Rocket Vehicle Applications) programs, twenty rocket reactors were designed, built and ground tested. These tests demonstrated: (1) a wide range of thrust; (2) high temperature carbide-based nuclear fuel; (3) sustained engine operation; (4) accumulated lifetime; and (5) restart capability - all the requirements needed for a human mission to Mars. Ceramic metal fuel was also evaluated as a backup option. In NASA's recent Mars Design reference Architecture (DRA) 5.0 study, the NTR was selected as the preferred propulsion option because of its proven technology, higher performance, lower launch mass, versatile vehicle design, simple assembly, and growth potential. In contrast to other advanced propulsion options, NTP requires no large technology scale-ups. In fact, the smallest engine tested during the Rover program - the 25 klbf 'Pewee' engine is sufficient for a human Mars mission when used in a clustered engine configuration. The 'Copernicus crewed NTR Mars transfer vehicle design developed for DRA 5.0 has significant capability that can enable reusable '1-year' round trip human missions to candidate near Earth asteroids (NEAs) like 1991 JW in 2027, or 2000 SG344 and Apophis in 2028. A robotic precursor mission to 2000 SG344 in late 2023 could provide an attractive Flight Technology Demonstration of a small NTR engine that is scalable to the 25 klbf-class engine used for human missions 5 years later. In addition to the detailed scientific data gathered from on-site inspection, human NEA missions would also provide a valuable 'check out' function for key elements of the NTR transfer vehicle (its propulsion module, TransHab and life support systems, etc.) in a 'deep space' environment prior to undertaking the longer duration Mars orbital and landing missions that would follow. The initial mass in low Earth orbit required for a mission to Apophis is approximately 323 t consisting of the NTR propulsion module ((is) approximately 138 t), the integrated saddle truss and LH2 drop tank assembly ((is) approximately 123 t), and the 6-crew payload element ((is) approximately 62 t). The later includes a multi-mission Space Excursion Vehicle (MMSEV) used for close-up examination and sample gathering. The total burn time and required restarts on the three 25 klbf 'Pewee-class' engines operating at Isp (is) approximately 906 s, are approximately 76.2 minutes and 4, respectively, well below the 2 hours and 27 restarts demonstrated on the NERVA eXperimental Engine, the NRX-XE. The paper examines the benefits, requirements and characteristics of using NTP for the above NEA missions. The impacts on vehicle design of HLV payload volume and lift capability, crew size, and reusability are also quantified.

Borowski, Stanley↗
NASA NTRS2006

International Space Station (ISS) Water Transfer Hardware Logistics

Water transferred from the Space Shuttle to the International Space Station (ISS) is generated as a by-product from the Shuttle fuel cells, and is generally preferred over the Progress which has to launch water from the ground. However, launch mass and volume are still required for the transfer and storage hardware. Some of these up-mass requirements have been reduced since ISS assembly began due to changes in the storage hardware (CWC). This paper analyzes the launch mass and volume required to transfer water from the Shuttle and analyzes the up-mass savings due to modifications in the CWC. Suggestions for improving the launch mass and volume are also provided.

Shkedi, Brienne D.↗