SEARCH · Search NASA

Results for “grain structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1979

An oxide dispersion strengthened alloy for gas turbine blades

The strength of the newly developed alloy MA-6000E is derived from a nickel alloy base, an enlongated grain structure, naturally occurring precipitates of gamma prime, and an artificial distribution of extremely fine, stable oxide particles. Its composition is Ni-15% Cr-2% Mo-2% Ta-4% W-4.5% Al-2.5% Ti-0.15% Zr-0.05% C-0.01% B-1.1% Y2O3. It exhibits strength of a conventional nickel-base alloy at 1400 F, but is quite superior at 2000 F. Its shear strength is relatively low, necessitating consideration of special joining procedures. Its high-cycle, low-cycle, and thermal fatigue properties are excellent. The relationship between alloy micro-structure and properties is discussed.

Glasgow, T. K.↗

NASA NTRS1978

Growth, evaluation and modeling of silicon-on-ceramic solar cells

The silicon-on-ceramic (SOC) process uses inexpensive ceramic substrates to provide supported growth of silicon from the melt. The conditions for unidirectional solidification, the grain structure and other properties are quite similar to those of EFG silicon ribbon. Solar cells with interdigital electrodes have demonstrated AMl conversion efficiencies (active area) of 7.8% without AR coatings and 10.1% efficiencies with an AR coating of SiO. Mathematical modeling of the series resistance of cells shows the feasibility of making electrical contact to the base layer of the cell through slots in the substrate. However, series resistance in the base layer sets an upper limit on slot spacing for efficient cell performance.

Zook, J. D.↗

NASA NTRS1980

Etchant for incoloy-903 welds

Special reagent consists of 1 part 90% lactic acid, 1 part 70% nitric acid, and 4 part, 37% hydrochloric acid. Solution etches parent and weld metals at same rate, without overetching. Underlying grain structure of both metals is revealed.

Gerstmeyer, J. A.↗

NASA NTRS1980

Fatigue properties of MA 6000E, a gamma-prime strengthened ODS alloy

MA 6000E is a corrosion resistant, gamma-prime strengthened ODS alloy under development for advanced turbine blade applications. The high temperature, 1093 C, rupture strength is superior to conventional nickel-base alloys. This paper addresses the fatigue behavior of the alloy. Excellent properties are exhibited in low and high cycle fatigue and also thermal fatigue. This is attributed to a unique combination of microstructural features, i.e., a fine distribution of dispersed oxides and other nonmetallics, and the highly elongated grain structure which advantageously modify the deformation characteristics and crack initiation and propagation modes from that characteristic of conventional gamma-prime hardened superalloys.

Kim, Y. G.↗

NASA NTRS1982

Reconnaissance and recovery of the brighter asteroids. Brief summary of the entire project

An inexpensive method of baking large (8- by 10-inch) IIIa-J plates in 2 percent forming gas was found and successfully tested. The large storage capacity and fine grain structure of the emulsion made the sky fog negligible on plates of one-hour exposure at Link. Plates were taken through the end of October 18, 1981 on various asteroids from the recent critical lists published in the Minor Planet Circulars and the Russian Ephemeris of Minor Planets.

Edmonson, F. K.↗

NASA NTRS1981

Structure of the St. Francois Mountains and surrounding lead belt, S. E. Missouri: Inferences from thermal IR and other data sets

Heat Capacity Mapping Mission (HCMM) in the form of an apparent thermal inertia image were merged with shaded relief maps and Bouguer gravity maps. The HCMM data show that the dominant structural grain in Missouri strikes in a northwesterly direction. The strike is the same as a major basement fault or flexure identified on the basis of gravity images.

Arvidson, R. E.↗

NASA NTRS1983

The Pikwitonei granulite domain: A lower crustal level along the Churchill-Superior boundary in central Manitoba

The greenschist to amphibolite facies tonalite-greenstone terrain of the Gods Lake subprovince grades - in a northwesterly direction - into the granulite facies Pikwitonei domain at the western margins of the Superior Province. The transition is the result of prograde metamorphism and takes place over 50 - 100 km without any structural or lithological breaks. Locally the orthopyroxene isograd is oblique to the structural grain and transects greenstone belts, e.g., the Cross Lake belt. The greenstone belts in the granulite facies and adjacent lower grade domain consist mainly of mafic and (minor) ultramafic metavolcanics, and clastic and chemical metasedimentary rocks. Typical for the greenstone belts crossed by the orthopyroxene isograd are anorthositic gabbros and anorthosites, and plagiophyric mafic flows. The Pikwitonei granulite domain has been interpreted as to represent a lower crustal level which was uplifted to the present level of erosion. On the basis of gravimetric data this uplift has been modelled as an obduction onto the Churchill Province during the Hudsonian orogeny, similar to the Ivrea Zone. The fault between the Churchill and Superior Province is described.

Weber, W.↗

NASA NTRS1984

Effects of Non-equilibrium Solidification on the Material Properties of Brick Silicon for Photovoltaics

Silicon ingot growth technologies like the Ubiquitous Crystallization Process (UCP) are solidified within a shaping crucible. The rate at which heat can be lost from this crucible minus the rate at which heat is input from an external source determines the rate at which crystallization will occur. Occasionally, when the process parameters for solidification are exceeded, the normally large multi-centimeter grain size material assocated with the UCP will break down into regions containing extremely small, millimeter or less, grain size material. Accompanying this breakdown in grain growth is the development of so called sinuous grain boundaries. The breakdown in grain growth which results in this type of small grain structure with sinuous boundaries is usually associated with the rapid crystallization that would accompany a system failure. This suggests that there are limits to the growth velocity that one can obtain and still expect to produce material that would possess good photovoltaic properties. It is the purpose to determine the causes behind the breakdown of this material and what parameters will determine the best rates of solidification.

Regnault, W. F.↗

NASA NTRS1986

Electromagnetic Hammer for Metalworking

High eddy currents apply pressure for cold-forming. Coil housing constructed for mechanical strength to hold coil against magnetic force, to maintain electrical contact with coil ends, and to maintain insulation between coil turns. Drilled holes placed to facilitate release of bubbles during potting. In contrast with mechanical hammers, electromagnetic hammer requires no dynamic material contact with workpiece; consequently, produces almost no change in metal grain structure.

Anderson, S. A.↗

NASA NTRS1986

Plasma diagnosis from thermal noise and limits on dust flux or mass in comet Giacobini-Zinner

Thermal noise spectroscopy was used to measure the density and temperature of the main (cold) electron plasma population during two hours around the point of closest approach of the International Cometary Explorer (ICE) to comet Giacobini-Zinner. The time resolution was 18 seconds in the plasma tail and 54 seconds elsewhere. Near the tail axis, the maximum plasma density was 670/cu cm and the temperature slightly above one volt. Away from the axis, the plasma density dropped to 100/cu cm over 2000 km, then decreased to 10/cu cm over 15,000 km; at the plasma tail, the density fluctuated between 10 and 30/cu cm, and the temperature, between 100,000 and 400,000 K. No evidence was found of grain impact on the spacecraft or antennas in the plasma tail. This yields an upper limit for the dust flux or particle mass, indicating either fluxes or masses in the tail smaller than those implied by models or an anomalous grain structure. Outside the tail, and particularly near 100,000 km from its axis, impulsive noises indicating plasma turbulence were observed.

Meyer-Vernet, N.↗

NASA NTRS1987

A preliminary study of factors affecting the calibration stability of the iridium versus iridium-40 percent rhodium thermocouple

An iridium versus iridium-40% rhodium thermocouple was studied. Problems associated with the use of this thermocouple for high temperature applications (up to 2000 C) were investigated. The metallurgical studies included X-ray, macroscopic, resistance, and metallographic studies. The thermocouples in the as-received condition from the manufacturer revealed large amounts of internal stress caused by cold working during manufacturing. The thermocouples also contained a large amount of inhomogeneities and segregations. No phase transformations were observed in the alloy up to 1100 C. It was found that annealing the thermocouple at 1800 C for two hours, and then at 1400 C for 2 to 3 hours yielded a fine grain structure, relieving some of the strains, and making the wire more ductile. It was also found that the above annealing procedure stabilized the thermal emf behavior of the thermocouple for application below 1800 C (an improvement from + or - 1% to + or - 0.02% within the range of the test parameters used).

Ahmed, Shaffiq↗

NASA NTRS1987

Curvilinear ridges and related features in southwest Cydonia Mensae, Mars

Examined is a region on Mars in southwest Cydonia Mensae (32 deg lat., 17 deg long.) just northwest of the lowland/upland boundary escarpment. The dominant morphological features in this region are the clusters of large massifs and plateau outliers (PI), knobby material (K), and smooth lowland plains (Ps). Surrounding the clusters and linking many isolated knobs is a system of curvilinear ridges and arcuate terrain boundaries which tend to separate the massifs and knobs from the smooth plains. Curvilinear ridges are arcuate to nearly linear and smoother in plan than wrinkle ridges and show no apparent correlation with regional structural grain. They are typically 5 to 10 km long but can range from as little as 2 or 3 km to greater than 50 km long. The widths vary from about 100 m to as much as 2 km. Curvilinear ridges are most numerous within 100 km of the lowland/upland boundary escarpment and are associated with massifs and knobby terrain. Arcuate terrain boundaries appear between units of different apparent albedo or arcuate breaks in slope.

Parker, Timothy J.↗

NASA NTRS1986

Microstructural variations induced by gravity level during directional solidification of near-eutectic iron-carbon type alloys

The effects of gravity on the microstructure of directionally solidified near-eutectic cast irons are studied, using a Bridgman-type automatic directional solidification furnace aboard a NASA KC-135 aircraft which flies parabolic arcs and generates alternating periods of low-g (0.01 to 0.001 g, 30 seconds long) and high-g (1.8 g, 1.5 minutes long). Results show a refinement of the interlamellar spacing of the eutectic during low-g processing of metastable Fe-C eutectic alloys. Low-g processing of stable Fe-C-Si eutectic alloys (lamellar or spheroidal graphic) results in a coarsening of the eutectic grain structure. Secondary dendrite arm spacing of austenite increases in low-g and decreases in high-g. The effectiveness of low-gravity in the removal of buoyancy-driven graphite phase segregation is demonstrated.

Stefanescu, Doru M.↗

NASA NTRS1987

Microstructures of undercooled germanium droplets

Undercoolings at crystal nucleation onset of liquid Ge droplets are measured and the microstructures of the droplets are examined. Undercooling values ranging from 150-415 + or 20 C were obtained. It is observed that for the samples undercooled less than 300 C prior to solidification the grain size was greater than 100 microns; for samples undercooled between 300-400 C the grain size was between 50-100 microns; and for samples undercooled greater than 400 C the grain size was 10-20 microns. Consideration is given to dendritic growth and interfacial undercooling. It is noted that there is a correlation between undercooling and as-crystallized grain structure.

Devaud, G.↗

NASA NTRS1989

Effect of processing on fracture toughness of silicon carbide as determined by Vickers indentations

Several alpha-SiC materials were processed by hot isostatic pressing (HIPing) and by sintering an alpha-SiC powder containing boron and carbon. Several beta-SiC materials were processed by HIPing a beta-SiC powder with boron and carbon additions. The fracture toughnesses K(sub 1c) of these beta- and alpha-SiC materials were estimated from measurements of Vickers indentations. The three formulas used to estimate K(sub 1c) from the indentation fracture patterns resulted in three ranges of K(sub 1c) estimates. Furthermore, each formula measured the effects of processing differently. All three estimates indicated that fine-grained HIPed alpha-SiC has a higher K(sub 1c) than coarsed-grained sintered alpha-SiC. Hot isostatically pressed beta-SiC, which had an ultrafine grain structure, exhibited a K(sub 1c) comparable to that of HIPed alpha-SiC.

Dannels, Christine M.↗

NASA NTRS1991

Melt-processed bulk superconductors: Fabrication and characterization for power and space applications

Melt-process bulk superconducting materials based on variations on the base YBa2Cu3O(x) were produced in a variety of shapes and forms. Very high values of both zero-field and high-field magnetization were observed. These are useful for levitation and power applications. Magnetic measurements show that the effects of field direction and intensity, temperature and time are consistent with an aligned grain structure with multiple pinning sites and with models of thermally activated flux motion.

Hojaji, Hamid↗

NASA NTRS1991

Recrystallization and superplasticity at 300 C in an aluminum-magnesium alloy

Variations in thermomechanical processing (TMP) which regulate the microstructural characteristics and superplastic response of an Al-10Mg-0.1Zr alloy at 300 C were evaluated. Mechanical property data revealed that the superplastic ductility can be enhanced by simultaneously increasing the total rolling strain, the reduction per pass, and the duration of reheating intervals between passes during isothermal rolling. Texture and microscopy data were consistent with the development of a refined microstructure by recovery-dominated processes, i.e., continuous recrystallization, during the processing. The mechanisms by which a refined substructure can be progressively converted into a fine-grained structure during repeated cycles of deformation and annealing are addressed. A qualitative description of the complex sequence of developments leading to a microstructure better suited to support superplastic response is presented.

Hales, S. J.↗

NASA NTRS1992

Improved Warm-Working Process For An Iron-Base Alloy

Warm-working process produces predominantly unrecrystallized grain structure in forgings of iron-base alloy A286 (PWA 1052 composition). Yield strength and ultimate strength increased, and elongation and reduction of area at break decreased. Improved process used on forgings up to 10 in. thick and weighing up to 900 lb.

Cone, Fred P.↗