Search NASA⌕ Search

SEARCH · Search NASA

Results for “high speed stream”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Compressible studies on dynamic stall

The purpose of this work is to investigate the effects of compressibility on the dynamic stall phenomenon by numerical simulation of the unsteady flow. The full two-dimensional unsteady compressible Navier-Stokes equations are solved for flows over oscillating airfoils and airfoils pitching rapidly to high angles of attack. The free-stream speeds vary from low subsonic with mild compressibility effects, to moderate subsonic where strong compressibility effects appear close to the leading edge at high angles of attack. An Alternating Direction Implicit scheme is implemented for the numerical solution with the viscous terms retained in both directions. The numerical results are compared with available experimental data for a Sikorsky airfoil for compressible high Reynolds number flows. There is good agreement between the computed and measured unsteady lift and pitching moment coefficient time histories. The computed high-speed subsonic unsteady results give a good picture of the entire flow field, and the dynamic stall progression in the compressible flow regime. It was observed that compressibility effects are more severe close to the leading edge at moderate angles of attack, and that the dynamic stall vortex appears at lower angles of attack as the free-stream speed increases.

Ekaterinaris, J. A.↗
NASA NTRS1994

Acceleration and heating of two-fluid solar wind by Alfven waves

Earlier model studies of solar wind driven by thermal pressure and Alfven waves have shown that wave amplitudes of 20-30 km/s at the coronal base are sufficient to accelerate the flow to the high speeds observed in quasi-steady streams emanating from large coronal holes. We focus on the energy balance in the proton gas and show that heat conduction from the region where the waves are dissipated may play an important role in determining the proton temperature at the orbit of Earth. In models with 'classical' heat conduction we find a correlation between high flow speed, high proton temperature, and low electron temperature at 1 AU. The effect of wave heating on the development of anisotropies in the solar wind proton gas pressure is also investigated in this study.

Sandbaek, Ornulf↗
NASA NTRS2014

Simulation of VSPT Experimental Cascade Under High and Low Free-Stream Turbulence Conditions

Variable-Speed Power Turbines (VSPT) for rotorcraft applications operate at low Reynolds number and over a wide range in incidence associated with shaft speed change. A comprehensive linear cascade data set obtained includes the effects of Reynolds number, free-stream turbulence and incidence is available and this paper concerns itself with the presentation and numerical simulation of conditions resulting in a selected set of those data. As such, post-dictions of blade pressure loading, total-pressure loss and exit flow angles under conditions of high and low turbulence intensity for a single Reynolds number are presented. Analyses are performed with the three-equation turbulence models of Walters-Leylek and Walters and Cokljat. Transition, loading, total-pressure loss and exit angle variations are presented and comparisons are made with experimental data as available. It is concluded that at the low freestream turbulence conditions the Walters-Cokljat model is better suited to predictions while for high freestream conditions the two models generate similar predications that are generally satisfactory.

low pressure trubine↗
NASA NTRS2015

Simulation of VSPT Experimental Cascade Under High and Low Free-Stream Turbulence Conditions

Variable-Speed Power Turbines (VSPT) for rotorcraft applications operate at low Reynolds number and over a wide range in incidence associated with shaft speed change. A comprehensive linear cascade data set obtained includes the effects of Reynolds number, free-stream turbulence and incidence is available and this paper concerns itself with the presentation and numerical simulation of conditions resulting in a selected set of those data. As such, post-dictions of blade pressure loading, total-pressure loss and exit flow angles under conditions of high and low turbulence intensity for a single Reynolds number are presented. Analyses are performed with the three-equation turbulence models of Walters- Leylek and Walters and Cokljat. Transition, loading, total-pressure loss and exit angle variations are presented and comparisons are made with experimental data as available. It is concluded that at the low freestream turbulence conditions the Walters-Cokljat model is better suited to predictions while for high freestream conditions the two models generate similar predications that are generally satisfactory.

turbulence modeling↗
NASA NTRS2014

Simulation of VSPT Experimental Cascade Under High and Low Free-Stream Turbulence Conditions

Variable-Speed Power Turbines (VSPT) for rotorcraft applications operate in conditions of low Reynolds number and a wide range in incidence resulting from rotational speed variation. A comprehensive data set obtained in a linear cascade which includes the effects of Reynolds number, free-stream turbulence and incidence is now available and this paper concerns itself with the post-diction of boundary layer transitionseparation, blade pressure loading and total pressure loss pertaining to the conditions set for measurements in that data set. The distinction between the state of the measured data presented here and the earlier publications is the addition of high free-stream turbulence intensity. We will, for the purposes of the numerical post-diction, present some of the higher free stream turbulence data in this paper but defer a comprehensive presentation and treatment of the measured data will be done elsewhere.

power turbine↗
NASA NTRS1992

CCD data acquisition systems at Lick and Keck Observatories

This paper will describe and compare two distinct but related CCD data acquisition systems (DAS) currently under development at Lick and Keck Observatories. Although these two systems have a number of major architectural differences, they share a considerable amount of common hardware and software. Both of these new systems build on a large body of proven software that is the foundation of the existing CCD DAS currently in use at Lick Observatory. Both will provide support for reading up to four on-chip amplifiers per CCD and/or reading out mosaics of CCD chips. In addition, they will provide the capability for interactive, real-time adjustment of CCD waveforms for engineering purposes. Each of these two systems is composed of three major subsystems: (1) an instrument computer and its software; (2) a data capture computer and its software; and (3) a CCD/dewar controller and its software. The instrument computer is a Unix workstation, and the functions it provides include user interfaces, the interactive real-time display of CCD images, and the recording of image and FITS header data to disk and/or tape. The data capture computer is responsible for the packaging and high-speed transfer of the CCD pixel data stream into a bulk RAM, and the subsequent transfer of this data to the instrument computer. The CCD/dewar controller generates the waveforms for clocking the CCD, digitizes the pixel data, and transmits it via high-speed link to the data capture computer. It is also responsible for monitoring and controlling the dewar temperature and cryogen levels. Given the number of different types of processors and high-speed data links employed in both systems, a major emphasis of this paper will be on the various forms of interprocessor communications utilized for data transfer and distributed process synchronization.

Kibrick, R. I.↗
NASA NTRS1976

An experimental study of the structure and acoustic field of a jet in a cross stream

The plane of symmetry of a high speed circular jet was surveyed to measure the mean and turbulent velocity fields by using constant temperature hot wire anemometry. The intensity of the noise radiated from the jet was determined in the tunnel test section by utilizing the cross-correlation at a particular time delay between the signals of two microphones suitably located along a given direction. Experimental results indicate that the turbulent intensity inside the crossflow jet increases by a factor of (1 + 1/2) as compared to the turbulent intensity of the same jet under free conditions, with r indicating the ratio of the jet velocity by the cross stream velocity. The peak observed in the turbulence spectra obtained inside the potential core of the jet has a frequency that increases by the same factor with respect to the corresponding frequency measured in the case of the free jet. The noise radiated by the jet becomes more intense as the crossflow velocity increases. The measured acoustic intensity of the crossflow jet is higher than the value which would be expected from the increase of the turbulent intensity only.

Camelier, I.↗
NASA NTRS1993

Evolution of a high-performance storage system based on magnetic tape instrumentation recorders

In order to provide transparent access to data in network computing environments, high performance storage systems are getting smarter as well as faster. Magnetic tape instrumentation recorders contain an increasing amount of intelligence in the form of software and firmware that manages the processes of capturing input signals and data, putting them on media and then reproducing or playing them back. Such intelligence makes them better recorders, ideally suited for applications requiring the high-speed capture and playback of large streams of signals or data. In order to make recorders better storage systems, intelligence is also being added to provide appropriate computer and network interfaces along with services that enable them to interoperate with host computers or network client and server entities. Thus, recorders are evolving into high-performance storage systems that become an integral part of a shared information system. Data tape has embarked on a program with the Caltech sponsored Concurrent Supercomputer Consortium to develop a smart mass storage system. Working within the framework of the emerging IEEE Mass Storage System Reference Model, a high-performance storage system that works with the STX File Server to provide storage services for the Intel Touchstone Delta Supercomputer is being built. Our objective is to provide the required high storage capacity and transfer rate to support grand challenge applications, such as global climate modeling.

Peters, Bruce↗
NASA NTRS1951

Wind-tunnel investigation of six shielded total-pressure tubes at high angles of attack subsonic speeds

The effect of inclination of the air stream on the measured pressures of six shielded total-pressure tubes (all designed for end-mounting on a horizontal boom) has been determined for an angle-of-attack range of approximately -30° to 65°. The tests were conducted at a Mach number of 0.26 in the Langley stability tunnel and at Mach numbers of 0.50, 0.70, 0.90, and 0.95 in the Langley high-speed 7- by 10-foot tunnel. The results of the tests showed that curved venturi entries are less sensitive to inclination of the air stream than the conical entry of the standard Kiel design. Of the three curved entries tested, the tube having the bluntest entry proved the least sensitive to inclination. The critical angle (that is, the sngle.at which the total-pressure error equals 1 percent of the impact pressure) for this tube was ±63.2° at a Mach number of 0.26. The tests also showed that the critical angle of a shielded tube could be extended to higher positive angles of attack by means of a slant profile. The critical angle of a tube having a conical entry with a 10° slant profile, for example, was found to average 9° greater than that of a similar tube having a square profile. Although the critical angle of this tube at angles of yaw was less than that at angles of attack, the critical angle in yaw was equal to that of the tube with the square profile. Tests of the effect of varying the position of the total-pressure probe in the shield showed that, in general, no advantage was to be gained by changing from the position used in the standard Kiel design. Limited tests of the effect of varying the internal diameter of the shield showed that an increase in the diameter of the throat corresponding an increase in the internal area of 50 percent resulted in a relatively small increase (2.5°) in the critical angle. The effect of Mach number on the sensitivity of the tubes to inclination was shown to be appreciable. An increase in Mach number from 0.26 to 0.90, for example, resulted in a decrease in the critical angle of most of the tubes of about 4°.

Walter R Russell↗
NASA NTRS1979

High performance N2O4/amine elements blowapart

Hypergolic earth-storable N2O4/Amine propellants are used for a wide range of liquid propulsion system applications. These propellants are highly reactive and can experience reactive stream separation (RSS, i.e., blowapart) which can inhibit intraelement mixing, hence reducing the overall spray mixture ratio and mass distribution, which can result in altered combustion efficiency, gas-side heat transfer coefficient, and stability. An experimental and analytical program was conducted to develop an understanding of the mechanisms controlling RSS. The program and product was development of design criteria for coping with RSS to allow the design of high performing, stable injectors. RSS mechanisms were identified using high speed color photography to observe reactive stream mixing of single element injectors tested with N2O4/MMH, N2O4/A-50, and N2O4/N2H4 propellants. The parametric characterization included modeling of the Space Shuttle Orbital Maneuvering System and Reaction Control System engine injectors.

Source record↗
NASA NTRS1991

A high performance FDDI NIU for streaming voice, video, and data

A 100-Mbit/s FDDI network interface unit (NIU) is described that supports real-time data, voice and video. Its high-speed interrupt-driven hardware architecture efficiently manages stream and packet data transfers to the FDDI network. Other enhancements include modular single-mode laser-dioce fiber optic links to maximize node spacing, optic bypass switches for increased fault tolerance, and a hardware performance monitor to gather real-time network diagnostics.

Bergman, L. A.↗
NASA NTRS1981

The Spacelab Lyman alpha and white light coronagraphs program

The Harvard-Smithsonian Center for Astrophysics and the High Altitude Observatory have defined a joint coronagraphs experiment for a future Spacelab mission. The instrumentation package would include an ultraviolet light coronagraph to measure the intensity and profiles of spectral lines formed between 1.2 and 8 solar radii from sun center and a white light coronagraph to measure the intensity and polarization of visible light. The overall goals of the joint program are to use new coronal plasma diagnostic techniques to understand the physical processes and mechanisms operating in the solar corona, to understand the acceleration of high-speed and low-speed solar wind streams and to extrapolate this knowledge to other stars in order to help understand the physics of stellar coronae and stellar mass loss.

Kohl, J. L.↗
NASA NTRS1992

Experiments on shear layer mixing at hypervelocity conditions

Utilization of an expansion tube to acquire turbulent, compressible free shear layer data with gases of direct relevance to hypersonic combustion systems (nitrogen, hydrogen, and oxygen) is demonstrated. Visualizations of the free shear layer by laser holographic interferometry and schlieren imaging show a distinctly asymmetric growth rate that is highly preferential toward the lower speed (secondary stream) side. For the nitrogen/nitrogen case, for which the convective velocity was lowest and convective Mach number highest, the growth rate on the primary side was virtually zero until the mixing layer reached the opposite (secondary) wall.

Erdos, John↗
NASA NTRS2005

Development of a Pulsed Combustion Actuator For High-Speed Flow Control

This paper describes the flow within a prototype actuator, energized by pulsed combustion or detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant chamber, and the products exit the device as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. The combustion chamber has been constructed with windows, and the flow inside it has been visualized using Planar Laser-Induced Fluorescence (PLIF). The pulsed jet at the exit of the device has been observed using schlieren.

Cutler, Andrew D.↗
NASA NTRS2006

Toward a High-Frequency Pulsed-Detonation Actuator

This paper describes the continued development of an actuator, energized by pulsed detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant tube and the products exit the tube as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. Pulsed detonations have been demonstrated in the lambda/4 mode of an 8 inch long tube at approximately 600 Hz. The pulsed jet at the exit of the device has been observed using shadowgraph and an infrared camera.

Cutler, Andrew D.↗
NASA NTRS2006

Toward a High-Frequency Pulsed-Detonation Actuator

This paper describes the continued development of an actuator, energized by pulsed detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant tube and the products exit the tube as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. Pulsed detonations have been demonstrated in the lambda/4 mode of an 8 inch long tube at approx. 600 Hz. The pulsed jet at the exit of the device has been observed using shadowgraph and an infrared camera.

Cutler, Andrew D.↗
NASA NTRS1986

Effects of compressibility and free-stream turbulence on boundary layer transition in high-subsonic and transonic flows

Based on the existing boundary layer transition data, the effects of compressibility, pressure fluctuations, and free-stream turbulence have been reexamined for subsonic and transonic flow speeds. It is confirmed that the compressibility effects may be adequately expressed in terms of a simple correlation with free-stream Mach number. Pressure fluctuations, especially at low levels, do not seem to significantly affect the transition phenomenon. Effects of free-stream turbulence in high-subsonic and transonic flows are similar to the trends observed for low-speed flows and the transition process is hastened. The trends, as seen from slender cone flow data, seem to suggest power law correlations between transition Reynolds number and free-stream turbulence.

Murthy, S. V.↗