Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Enhanced Surface Properties and Microstructure Evolution of Cr12MoV Using Ultrasonic Surface Rolling Process Combined with Deep Cryogenic Treatment

In this study, the enhanced surface properties and microstructure evolution of quenched and tempered cold work die steel Cr12MoV, which were induced by ultrasonic surface rolling process combined with deep cryogenic treatment (UDCT), were systematically investigated. The results indicated that UDCT had an advantage over conventional ultrasonic surface rolling process (USRP) in improving surface mechanical properties, including smaller surface roughness and smoother machined surface with less cracks and defects; higher surface microindentation hardness with the value of ~ 890 HV (increased by ~ 6.2% compared with USRP); and lower friction coefficient. Such enhancements in surface properties are mainly attributed to the martensitic transformation of retained austenite, the dispersion strengthening of small secondary carbides and the homogenized carbides distribution during UDCT.

36 MATERIALS SCIENCE↗

Effects of transient thermal shock on the microstructures and corrosion properties of a reduced activation high-entropy alloy

The devices would subject transient thermal shocks (TTS) during operation under extremely harsh conditions of nuclear fusion reactors, which inevitably exert significant impact on the microstructure and performance of structural materials. Here, a reduced activation VCrFeTa 0.2 W 0.2 high-entropy alloy (HEA) was developed by vacuum arc melting. The effects of electron beam induced TTS on its microstructure, microhardness, and corrosion properties were investigated. The results indicate that the weight fraction of each phase changes after TTS, showing a significant decrease in the content of BCC1 phase and an increase in the content of BCC2 and Laves phases. The content of BCC1 phase continues to decrease slightly with increasing the power of TTS. Besides, the microhardness of the alloy increases from ~673 HV to ~714 HV after TTS treatments. In the reduced activation HEA, TTS results in a relatively low corrosion current density of ~0.472 μA/cm 2 in 3.5 wt% NaCl solution, around one-third of the current density observed in the as-cast sample. Furthermore, the VCrFeTa 0.2 W 0.2 HEA after TTS exhibits a pitting potential of ~1.165 V SCE , which is much higher than that of the as-cast sample. The refined composite multiscale entropy method is employed to analyze the influence of TTS on current fluctuation behavior during the corrosion process. The reduced activation VCrFeTa 0.2 W 0.2 HEA exhibits excellent properties in harsh environments after TTS, thereby showing advantageous property in the field of nuclear structural materials. Furthermore, TTS is an efficient and controllable strategy for the improvement of the HEAs’ microstructures and performances.

36 MATERIALS SCIENCE↗

Examining Constituent Redistribution in U-19Pu-10Zr Fuel as it Evolves with Local Burnup

While constituent redistribution is a known irradiation behavior in U-Pu-Zr fuel, new data have shown it is more complex than our current understanding and predictive capabilities. The size and composition of redistributed rings evolve as a function of pin composition, burnup, geometry, and irradiation temperature. In this work, we extract microstructural information from optical microscopy conducted on U-19Pu-10Zr pins (irradiated between 1.9 at. % and 11.6 at. % peak burnup). Both manual image analysis techniques and machine learning-assisted segmentation are used to quantify the thicknesses of the cladding, fuel-cladding interaction layers, and rings of fuel constituent redistribution in addition to pore distribution. These microstructural features and individual redistributed regions affect local thermomechanical properties, and identifying the relationship between burnup and constituent redistribution will improve accurate prediction of advanced reactor fuel performance.

Constituent Redistribution↗

Scoping Studies to ascertain the change in the phase transition temperature of metallic fuels

Microstructure evolution due to irradiation in a nuclear reactor can have a dramatic effect on material properties. A better understanding of this evolution is necessary for developing improved nuclear fuels and materials. In the current scoping study we evaluate the influence of irradiation induced defects on the recrystallization temperature of a single component fuel surrogate.

36 MATERIALS SCIENCE↗

Controlled synthesis of MnSn(OH){sub 6}/graphene nanocomposites and their electrochemical properties as capacitive materials

We report the synthesis of novel MnSn(OH){sub 6}/graphene nanocomposites produced by a co-precipitation method and their potential application for electrochemical energy storage. The hydroxide decorated graphene nanocomposites display better performance over pure MnSn(OH){sub 6} nanoparticles because the graphene sheets act as conductive bridges improving the ionic and electronic transport. The crystallinity of MnSn(OH){sub 6} nanoparticles deposited on the surface of graphene sheets also impacts the capacitive properties as electrodes. The maximum capacitance of 31.2 F/g (59.4 F/g based on the mass of MnSn(OH){sub 6} nanoparticles) was achieved for the sample with a low degree of crystallinity. No significant degradation of capacitance occurred after 500 cycles at a current density of 1.5 A/g in 1 M Na{sub 2}SO{sub 4} aqueous solution, indicating an excellent electrochemical stability. The results serve as an example demonstrating the potential of integrating highly conductive graphene networks into binary metal hydroxide in improving the performance of active electrode materials for electrochemical energy storage applications. - Graphical abstract: Graphite oxide (GO) can be synthesized by oxidizing graphite using Hummers method. Graphene was reduced from GO by thermal exfoliation. In this work, MnSn(OH){sub 6}/graphene nano-composites were synthesized by a simple co-precipitation method and their electrochemical performances have been explored. Highlights: Black-Right-Pointing-Pointer Noval MnSn(OH){sub 6}/graphene nano-composites were synthesized. Black-Right-Pointing-Pointer Microstructure can be tailored by changing the reaction temperature and time. Black-Right-Pointing-Pointer Crystallinity of MnSn(OH){sub 6} nanoparticles impacts capacitive properties as electrode. Black-Right-Pointing-Pointer Nano-composites display improved electrochemical performance over MnSn(OH){sub 6} alone. Black-Right-Pointing-Pointer Results serve as an example demonstrating the potential for energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure and interfacial reactions of soldering magnesium alloy AZ31B

In this paper, economic and innoxious solder alloys with low melting temperature were designed for AZ31B. Their chemical composition and relevant parameters were investigated for a high-performance structure of bonding region. Results of microstructure observation showed that Zn-enriched phases disappeared and {alpha}-Mg existed in the joints in the form of coarse dendrites by increasing the concentration of Mg in the solder alloys. Water cooling with a high cooling rate was adopted in experiments. Experimental research showed that high cooling rate restricted the grains of {alpha}-Mg as the equiaxed dendrites, which was about 1/5 of the coarse dendrite but their number was more than 40-50 times. Both morphology with typical fracture and the analysis on X-ray diffraction fracture indicated that equiaxed dendrites significantly improved the mechanical property of the joints. Necking phenomenon occurred in the bonding region was in favor of the improvement of joint shear strength.

36 MATERIALS SCIENCE↗

Microstructure and dielectric properties of BaTiO{sub 3} ceramic doped with yttrium, magnesium, gallium and silicon for AC capacitor application

Graphical abstract: Core–shell structure can be obtained in BaTiO{sub 3} ceramics co-doped with Y–Mg-Ga-Si. Y-Mg-Ga-Si co-dopant can obviously reduce dielectric loss, improve AC breakdown voltage and flatten temperature dependence of capacitance curve. - Highlights: • Y-Mg-Ga-Si co-doped BaTiO{sub 3} ceramics with core-shell structure were prepared. • Y{sup 3+}, Mg{sup 2+}, and Ga{sup 3+} dissolved in the lattice BaTiO{sub 3} replacing Ba{sup 2+} site or Ti{sup 4+} site. • Y{sup 3+} and Ga{sup 3+} tended to remain close to the grain boundaries as a shell maker. • Y-Mg-Ga-Si co-doped BaTiO{sub 3} ceramics show high AC breakdown voltage and low tanδ. - Abstract: The microstructures and dielectric properties of Y-Mg-Ga-Si co-doped barium titanate ceramics were investigated. Y{sup 3+} dissolved in the lattice of BaTiO{sub 3} replacing both Ba{sup 2+} site and Ti{sup 4+} site, and Mg{sup 2+} replaced Ti{sup 4+} site. The replacements of Y{sup 3+} and Mg{sup 2+} inhibit the grain growth, cause tetragonal-to-pseudocubic phase transition, reduce the dielectric loss, and flatten the temperature dependence of capacitance curve. The incorporation of Ga{sup 3+} can improve sintering and increase permittivity. Y{sup 3+} and Ga{sup 3+} tended to remain close to the grain boundaries, and play an important role as a shell maker in the formation of the core–shell structure in the co-doped BaTiO{sub 3} ceramics. Excellent dielectric properties: ϵ{sub r} = ∼2487, tanδ = ∼0.7% (at 1 kHz), ΔC/C{sub 25} < ∼6.56% (from −55 °C to 125 °C) and alternating current breakdown voltage E < ∼4.02 kV/mm can be achieved in the BaTiO{sub 3}–0.02Y{sub 2}O{sub 3}–0.03MgO–0.01Ga{sub 2}O{sub 3}–0.005SiO{sub 2} ceramics sintered at 1380 °C. This material has a potential application in alternating current multilayer ceramic capacitor.

36 MATERIALS SCIENCE↗

Graphene nanoplatelets reinforced cement as a solution to leaky wellbores reinforcing weak points in hydrated Portland cement with graphene nanoparticles improves mechanical and chemical durability of wellbore cements

In this work, to improve the performance of wellbore cement under subsurface environments, graphene nanoplatelets (GNPs) were added in various percentages to Class-H cement slurry. Microstructural characterization of cement slurries cured at 90 °C and 95% RH indicates that GNP modifies the microstructure of hydrated cement by reinforcing pore spaces. As a result, the mechanical properties, such as Young's modulus and axial peak stress, obtained from high temperature triaxial compression tests are significantly improved based on different percentages of added GNPs. Furthermore, the hydrated 1 × 2 inch GNP- Portland cement cores tested under simulated deep wellbore conditions of high-temperature and high pressure (HTHP), appear to have a ductile-like behavior, when compared to a typical brittle nature of Portland cement pastes. From our observations and published data on graphene resistance to fracture, GNP addition to cement is evidently enhancing the flexibility of cement. These improvements would reduce the risks associated with wellbore cement deterioration and a consequent leakage in fossil fuel production, geothermal energy production, CO 2 storage as well as long-term sealing materials in plugging and abandonment of all wellbores at the end of their service life.

36 MATERIALS SCIENCE↗

Influence of Welding Combined Plastic Forming on Microstructure Stability and Mechanical Properties of Friction Stir-Welded Al-Cu Alloy

A new tailor-welded process, which combines stages of welding, plastic forming, and heat treatment strengthening, was developed to produce a friction stir-welded (FSW) Al-alloy joint. The Al-Cu sheets were FSW under different welding parameters and then were plastic-deformed. The microstructural evolution and mechanical properties of the FSW joint were investigated by scanning electron microscopy and tensile tests. It was found that high heat input during FSW and low solution temperature suppress the abnormal grain growth (AGG) of the joint due to the differential in grain size and grain boundary energy. The microstructure heterogeneity of the FSW joint is effectively improved, as no AGG occurs. The retention of fine equiaxed grains and the increase in the density of precipitates result in excellent mechanical properties. The increase in the strength and micro-hardness of the joint mainly depends on the plastic deformation prior to aging treatment.

36 MATERIALS SCIENCE↗

Enhanced mechanical properties of carbon-doped FeNiMnAlCr high entropy alloy via hot-rolling

This work demonstrates an improvement in the mechanical performance of the high entropy alloy Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 containing 1.1 at. % carbon (CHEA) by hot-rolling followed by annealing at 1323 K. The microstructure was examined using scanning electron microscopy, electron backscatter diffraction, X-ray diffraction, and transmission electron microscopy. Room-temperature tensile tests were used to assess the alloy's mechanical properties. The presence of dense dislocation walls indicate that the alloy has not fully recrystallized and, moreover, the deformation substructure and the large fraction of Σ3 twin boundaries contribute to the high room temperature yield strength (~523 MPa). Despite the presence of substantial dislocation density, the annealed, hot-rolled CHEA displays an improvement in elongation to fracture (~33%) compared to the negligible ductility (< 2%) observed for the alloy after it has been simply annealed. Finally, the present work shows that hot rolling can produce good strength and ductility in the alloy while establishing the processing conditions necessary for the large-scale manufacture and utilization of its remarkable properties.

36 MATERIALS SCIENCE↗

Influence of the substrate temperature on the microstructure and electron-induced secondary electron emission properties of MgO/Au composite film

Highlights: • MgO/Au film was prepared by magnetron sputtering of individual Mg and Au targets. • A higher substrate temperature (T{sub s}) is conducive to the growth of MgO grains. • The surface roughness firstly rises and then decreases with T{sub s} increasing. • The increase of T{sub s} greatly enhances the SEE coefficient of the composite film. - Abstract: The influence of the substrate temperature (T{sub s}) on the microstructure and electron-induced secondary electron emission (SEE) properties of MgO/Au composite film prepared by reactive magnetron sputtering was investigated in order to improve the SEE performance of this composite film. During the deposition of MgO/Au film, a relatively high T{sub s} is conducive to the growth of MgO grains and causes the formation of some large aggregated gold particles on which MgO grains cover in the composite film. In terms of the SEE properties of MgO/Au film, the increase of T{sub s} brings about a significant improvement of SEE coefficient (δ), while it also leads to a slightly accelerated SEE degradation under the continuous electron bombardment due to a faster surface charging. The MgO/Au film prepared at T{sub s} of 773 K has a δ value of 4.9 at a primary electron energy of 200 eV and the maximum δ value of 11.5.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A computational study of the effects of graphene additions on electrical properties of polycrystalline copper

The addition of graphene has recently shown promise as a route for the significant improvement of the bulk electrical properties of metallic materials. Here, we explore the effects these additions have on the net electrical conductivity of fabricated copper-graphene (Cu-Gr) nanocomposites as a function of grain structure and grain boundary properties. Synthetic 3D microstructures were generated to represent polycrystalline copper with different average grain diameters and twinned grain boundary fractions. Then, the Poisson equation of electrical transport was solved using a finite difference method in order to predict the net electrical conductivity of each microstructure. In this context, the potential effect of graphene on the conductivity of the composite was evaluated as a function of the number of affected grain boundaries. The results of these calculations indicate that 1.) as supported by literature, net electrical conductivity decreases with decreasing grain size, 2.) the presence of twinned grain boundaries results in smaller loss of conductivity than would otherwise be expected, and 3.) the presence of graphene on the grain boundaries can be expected to lead to improvements in net electrical conductivity. However, we also find that 4.) when the Cu grain structure becomes sufficiently refined, the addition of graphene could conceivably result in significant improvements in electrical conductivity over and above coarse-grained Cu. It is estimated from our calculations that, assuming microstructures with average grain sizes between 100 nm and 100 μm and graphene conductivity 1000 to 10,000 that of a typical Cu grain boundary, an improvement in electrical conductivity of approximately 17% over that of bulk Cu may be attainable. Therefore, by performing this study we suggest a possible route for the improvement of Cu electrical properties through the addition of graphene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-scale investigation on mechanical behavior and microstructural alteration of C-S-H in carbonated Alite paste

Carbonation treatment is a promising option to enhance recycled concrete aggregate (RCA) quality and eventually improve concrete performance. This study investigated the multi-scale mechanical properties of calcium silicate hydrates (C-S-H) in a mature alite paste subjected to accelerated carbonation treatment by testing macro compressive strength, microhardness and nanoindentation. The results show that, carbonation treatment resulted in a heterogeneous distribution of carbonation products in the alite sample. Reinforcement of C-S-H by the randomly precipitated calcite and vaterite crystals prevailed over the nano-structural and compositional alteration of C-S-H induced by carbonation, leading to an increase of nano-indentation modulus at the edge of the sample. Also, the microhardness at the edge zone was markedly higher than that at the core of the carbonated sample. The carbonated peripheral zone with improved nano-scale modulus and microhardness was likely serving as a “hard shell”, contributing to the improved macro compressive strength. The new insights into the multi-scale mechanical properties of carbonated C-S-H contribute to further understanding of the enhanced properties of RCA after carbonation treatment.

36 MATERIALS SCIENCE↗

Development of a Squeeze Semisolid High-Pressure Die Casting Process for Magnesium Structural Parts

High-pressure die casting is the most common method used to produce magnesium castings, due to the excellent balance of cost and properties for high production volumes with limitations in terms of final mechanical properties. A newly developed process based on employing low injection speeds, in a range slightly over the standard semisolid speeds with a modified die, with thick gates and high die temperatures has been developed. Despite working with speeds that are not in the lamellar flow, the obtained parts present very low porosity, allowing the use thermal treatments to increase the ductility without producing blisters. The demonstration has been performed in a AM60B magnesium body joint produced by the squeeze casting process. Finally, the microstructure and the mechanical properties of as-cast and T4 heat-treated samples were studied. The results indicate the improvement of the mechanical properties in T4 heat-treated parts; specifically, a 40% improved deformation-to-failure, 40-60% improved penetration force and 90% of energy absorption were possible to obtain employing the newly developed SC + T4 process.

36 MATERIALS SCIENCE↗

Design and development of a high-performance Ni-based superalloy WSU 150 for additive manufacturing

This work proposes a design and development strategy of a new nickel-based superalloy for additive manufacturing. A new Ni-based superalloy has been developed by the application of the combinatorial alloy development technique coupled with CALPHAD based solidification modeling by effectively suppressing the precipitation kinetics. The suppression of precipitation during processing paved a way for prevention of cracks during deposition. The new alloy "WSU 150" revealed excellent room temperature mechanical properties with a yield strength of 867 MPa, an ultimate tensile strength of 1188 MPa, and an elongation of 27.9% in the as-deposited condition. The mechanical properties of the heat-treated alloy were improved significantly to 1114 MPa yield strength, 1396 MPa ultimate tensile strength, and an elongation of 16.1%. Improvement in the mechanical properties is attributed to the additional precipitation and coarsening of γ' and carbides during heat-treatment. Microstructural investigation of the alloy revealed spherical γ' with a rippled size distribution from the center to the interdendritic region. The average size of the γ' particles in the as-deposited condition was found to be around 48 nm in the interdendritic region. Heat-treatment promoted the coarsening of γ' which is explained in the paper.

36 MATERIALS SCIENCE↗

Precision surface modification of solid oxide fuel cells via layer-by-layer surface sol–gel deposition

While solid oxide fuel cells (SOFCs) are a promising technology for a clean and sustainable future, their commercialization is hindered by limited durability and performance. Here, we report our findings on the application of a layer-by-layer surface sol–gel (SSG) coating of catalysts to dramatically enhance the electro-catalytic activity and durability of SOFC cathodes. The SSG process is capable of penetrating and preserving complex backbone microstructures of porous electrodes, creating highly conformal coatings of controlled morphology, while tailoring the composition of the surface to improve catalytic properties and durability. For example, the application of an SSG coating of PrO x to a La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3–δ (LSCF) cathode has reduced the polarization resistance from 1.136 to 0.117 Ω cm 2 at 600 °C and the degradation rate from 1.13 × 10 –3 to 2.67 × 10 –4 Ω cm 2 h –1 at 650 °C. In addition, a continuous improvement in electrode performance is demonstrated as the thickness of the coating is increased, corresponding to the linear addition of catalyst. Furthermore, this first application of the SSG technique to SOFC systems opens the door for the controlled surface modification of porous components in electrochemical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of cryogenic treatment on the plastic property of Ti-6Al-4V titanium alloy

The effect of cryogenic treatment on the plastic property of Ti-6Al-4V plate was studied in the present work. After cryogenic treatment, the low temperature temper at 180 ▭ was conducted in one of the groups and the results were compared with that of the untreated and cryotreated ones. The SLX series program controlled cryogenic equipment was used for the cryogenic treatment. The tensile tests were conducted by universal tensile testing machine and parameters of elongation and area reduction were used to evaluate plastic property. The scanning electron microscope was used to study the morphology of microstructure and fracture surface. The results show that after cryogenic treatment alone the elongation increased 10.6% and the area reduction increased 13.5% while the strength reduced to a small extent. Cryogenic treatment followed with low temperature temper increased the elongation and area reduction just by the extent of 4.7% and 9.5%. It means that the additional low temperature temper after cryogenic is not beneficial to the tensile properties of Ti-6Al-4V alloy. The examination of microstructure by scanning electron microscopy revealed that cryogenic treatment reduced the content of β phase particles which is the main reason for the improvement in plasticity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the preparation of TiAl alloy by direct reduction of the oxide mixtures in calcium chloride melt

In recent years, TiAl-based intermetallic alloys are being increasingly considered for application in areas such as (i) automobile/transport sector (passenger cars, trucks and ships) (ii) aerospace industry (jet engines and High Speed Civil Transport propulsion system) and (iii) industrial gas turbines. These materials offer excellent (i) high temperature properties (at higher than 6000C) (ii) mechanical strength and (iii) resistance to corrosion and as a result have raised renewed interest. The combination of these properties make them possible replacement materials for traditional nickel-based super-alloys, which are nearly as twice as dense (than TiAl based alloys). Since the microstructures of these intermetallic alloys affect, to a significant extent, their ultimate performance, further improvements (by way of alteration/modification of these microstructures), have been the subject matter of intense research investigations. It has now been established that the presence of alloy additives, such as niobium, tantalum, manganese, boron, chromium, silicon, nickel and yttrium etc, in specific quantities, impart marked improvement to the properties, viz. fatigue strength, fracture toughness, oxidation resistance and room temperature ductility, of these alloys. From a number of possible alloy compositions, {gamma}-TiAl and Ti-Al-Nb-Cr have, of late, emerged as two promising engineering alloys/materials. . The conventional fabrication process of these alloys include steps such as melting, forging and heat treatment/annealing of the alloy compositions. However, an electrochemical process offers an attractive proposition to prepare these alloys, directly from the mixture of the respective oxides, in just one step. The experimental approach, in this new process, was, therefore, to try to electrochemically reduce the (mixed) oxide pellet to an alloy phase. The removal of oxygen, from the (mixed) oxide pellet, was effected by polarizing the oxide pellet against a graphite electrode in a pool of molten calcium chloride at a temperature of 9000C. The dominant mechanism of the oxygen removal was the ionization of oxygen followed by its subsequent discharge, as CO2/CO, at the anode surface. The removal of oxygen from the oxide mixture helped form the alloy in situ. The presentation shall cover the detailed experimental results pertaining to the preparation, evaluation and characterization of Ti-47Al-2Nb-2Cr (atom%) alloy.

36 MATERIALS SCIENCE↗