SEARCH · Search NASA
Results for “interdiffusion”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Current enhancement of CdTe-based solar cells
We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO 2 /SnO 2 :F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl 2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSe x Te 1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (V OC ). To overcome the V OC loss and maintain a high short-circuit current (J SC ), the CdTe cell configuration has been modified using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a V OC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a V OC of 831 mV, a J SC of 26.3 mA/cm 2 , and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.
Influence of CdTe Deposition Temperature and Window Thickness on CdTe Grain Size and Lifetime After CdCl 2 Recrystallization
Grain structure influences both transport and recombination in CdTe solar cells. Larger grains generally are obtained with higher deposition temperatures, but commercially it is important to avoid softening soda-lime glass. Furthermore, depositing at lower temperatures can enable different substrates and reduced cost in the future. We examine how initial deposition temperatures and morphology influence grain size and lifetime after CdCl 2 recrystallization. Techniques are developed to estimate grain distribution quickly with low-cost optical microscopy, which compares well with electron backscatter diffraction data providing corroborative assessments of exposed CdTe grain structures. Average grain size increases as a function of CdCl 2 temperature. For lower temperature close-spaced sublimation CdTe depositions, there can be more stress and grain segregation during recrystallization. However, the resulting lifetimes and grain sizes are similar to high-temperature CdTe depositions. The grain structures and lifetimes are largely independent of the presence and/or interdiffusion of Se at the interface, before and after the CdCl 2 treatment.
Spectrum-per-Pixel Cathodoluminescence Imaging of CdTe Thin-Film Bevels
We conduct T=6 K cathodoluminescence (CL) spectrum imaging with a nano-scale electron beam on beveled surfaces of CdTe thin-films at different critical stages of standard CdTe device fabrication. The through-thickness total CL intensity profiles are consistent with a reduction in grain boundary recombination due to the CdCl2 treatment. Color-coded maps of the low-temperature luminescence transition energies reveal that CdTe thin films have remarkably non-uniform opto-electronic properties, which depend strongly on sample processing history. The grain-to-grain S content in the interdiffused CdTe/CdS region is estimated from a sample size of thirty-five grains, and the S content in adjacent grains varies significantly in CdCl2-treated samples. A low-temperature luminescence model is developed to interpret spectral behavior at grain boundaries and grain interiors.
Studying the Recrystallization of Cu(InGa)Se 2 Semiconductor Thin Films by Silver Bromide In-situ Treatment
Cu(In,Ga)Se 2 samples were fabricated using a 3-stage thermal co-evaporation process on molybdenum back contact at low temperature. The process of recrystallization was carried out in between the 2 nd and 3 rd stages by flashing 25 mg of AgBr for 2 minutes. A change in morphological structure was observed as small grains transformed into large grains, as confirmed by XRD and SEM measurements. The decrease of the Ga gradient, seen in the SIMS depth profile, suggests Ga interdiffusion due to AgBr treatment. Altogether, the AgBr treatment contributes to a general improvement in device performance as compared to the as-deposited devices.
Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy
In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.
Electroluminescence and Transmission Electron Microscopy Characterization of Reverse-Biased AlGaN/GaN Devices
Reverse-bias stress testing has been applied to a large set of more than 50 AlGaN/GaN high electron mobility transistors, which were fabricated using the same process but with different values of the AlN mole fraction and the AlGaN barrier-layer thickness, as well as different substrates (SiC and sapphire). Two sets of devices having different defect types and densities, related to the different growth conditions and the choice of nucleation layer, were also compared. When subjected to gate drain (or gate-to-drain and source short-circuited) reverse-bias testing, all devices presented the same time-dependent failure mode, consisting of a significant increase in the gate leakage current. This failure mechanism occurred abruptly during step-stress experiments when a certain negative gate voltage, or critical voltage, was exceeded or, during constant voltage tests, at a certain time, defined as time to breakdown. Electroluminescence (EL) microscopy was systematically used to identify localized damaged areas that induced an increase of gate reverse current. This current increase was correlated with the increase of EL intensity, and significant EL emission during tests occurred only when the critical voltage was exceeded. Focused-ion-beam milling produced cross-sectional samples suitable for electron microscopy observation at the sites of failure points previously identified by EL microscopy. In highdefectivity devices, V-defects were identified that were associated with initially high gate leakage current and corresponding to EL spots already present in untreated devices. Conversely, identification of defects induced by reverse-bias testing proved to be extremely difficult, and only nanometer-size cracks or defect chains, extending vertically from the gate edges through the AlGaN/GaN heterojunction, were found. No signs of metal/semiconductor interdiffusion or extended defective areas were visible.
Mass Transport in Binary TiO 2 :SiO 2 and GeO 2 :SiO 2 Direct Ink Write Glasses
The mass transport mechanisms of Ti in TiO 2 :SiO 2 and Ge in GeO 2 :SiO 2 direct ink write, additively manufactured glasses were studied. Due to the low solubility of Ti in SiO2 and high melting point of TiO 2 relative to SiO 2 , Ti transport was found to occur via solid state interdiffusion between adjoining SiO 2 and TiO 2 precursor particles. The diffusivity of titanium in SiO 2 measured over typical sintering temperatures (1000-1300 °C) using Rutherford backscattering spectrometry was D = 9.1 × 10 -7 [m2/sec] exp ($\frac{378[\frac{kJ}{mol}]}{RT}$. This provides an estimate of ~30 nm for the diffusion length under typical sintering conditions (2 hrs. at 1200 °C). Although Ti and Ge have similar diffusivities in SiO 2 glass at low concentrations, GeO 2 was found to be much more mobile during the sintering of printed GeO 2 :SiO 2 green bodies. This was evident in glasses with phase separated GeO 2 regions over length scales of ~10 μm and in experiments involving binary xerogels in which GeO 2 migrated over ~10 μm through cracked, porous SiO 2 layers. Large phase separated regions and long transport lengths in GeO 2 :SiO 2 suggest that the transport of GeO 2 occurs prior to the densification of the SiO 2 matrix via an alternative mechanism such as capillary flow. These results inform important considerations in the design of index modifying inks for the direct ink write process, namely initial precursor phase, mutual solubility with the base SiO 2 glass, and mass transport throughout the sintering process.
Impact on aggregate/matrix bonding when a refractory contains zinc aluminate instead of spinel and magnesia‐chrome
The high hot strength of MgO–Cr 2 O 3 refractory is often ascribed to its intimate aggregate/matrix bonding. For a fundamental comparison with it, ~2 mm aggregates of MgO and Al 2 O 3 were separately embedded in ZnAl 2 O 4 and MgAl 2 O 4 matrices, sintered at 1600°C, and examined. It was found that similarity of thermal expansion coefficient (TEC) between the aggregate and the matrix is critical to achieve good bonding and this is more important than the extent of interdiffusion. The TEC mismatch of ≥ 5.7 × 10 -6 K -1 caused significant undesirable debonding in MgO aggregate/MgAl 2 O 4 matrix sample and MgO/ZnAl 2 O 4 despite >736 μm Zn 2+ diffusion depth in the latter. Direct bonding, as inferred from a thicker interfacial reaction layer and a greater shift of the aggregate/matrix interface before and after firing, was better in MgAl 2 O 4 /ZnAl 2 O 4 combination, followed by tabular Al 2 O 3 /ZnAl 2 O 4 and Al 2 O 3 /MgAl 2 O 4 . Powder X-ray diffraction indicated that the volatilization of ZnAl 2 O 4 at 1600°C in air was negligible compared to MgO–Cr 2 O 3 .
Harnessing Chemical Short‐Range Disorder to Improve Lithium Retention in Epitaxial LLTO Solid‐Electrolyte Thin Films
Lithium lanthanum titanate Li 3x La 2/3-x TiO 3 (LLTO) is a promising perovskite-based solid-state electrolyte for next-generation lithium-ion batteries, but controlling crystallinity and Li stoichiometry in thin-film form is challenging because high growth temperatures are required to achieve good crystallinity while Li remains strongly volatile. Here, we systematically investigate the effect of substrate temperature on epitaxial LLTO thin films grown by pulsed laser deposition. We identify a narrow growth window (750–800°C) in which LLTO films grow as c-axis oriented with atomically flat surfaces. Lower growth temperatures (<750°C) stabilize laterally extended, chemically disordered stripe domains that coexist with ordered LLTO regions, whereas higher temperatures (≥825°C) suppress these defects but promote island morphologies and Al/Ti interdiffusion. While spectroscopy measurements show that Ti remains in the 4+ oxidation state and Li is globally deficient for all films, our depth-resolved time-of-flight secondary ion mass spectrometry studies reveal that the 700°C film retains the highest Li content across its thickness. These results clarify how growth temperature controls crystallinity, chemical short-range disorder, and Li retention, and highlight moderate growth temperatures (∼700°C) as a route to mitigate Li loss in epitaxial solid-electrolyte films.
The effect of environment on thermal barrier coating lifetime
While the water vapor content of the combustion gas in natural gas-fired land-based turbines is ~10%, it can be 20–85% with coal-derived (syngas or H 2 ) fuels or innovative turbine concepts for more efficient carbon capture. Additional concepts envisage working fluids with high CO 2 contents to facilitate carbon capture and sequestration. To investigate the effects of changes in the gas composition on thermal barrier coating (TBC) lifetime, furnace cycling tests (1-h and 100-h cycles) were performed in air with 10, 50, and 90 vol. % water vapor and CO 2 -10% H 2 O and compared to prior results in dry air or O 2 . Two types of TBCs were investigated: (1) diffusion bond coatings (Pt-diffusion or Pt-modified aluminide) with commercial electron-beam physical vapor-deposited yttria-stabilized zirconia (YSZ) top coatings on second-generation superalloy N5 and N515 substrates and (2) high-velocity oxygen fuel (HVOF) sprayed MCrAlYHfSi bond coatings with air plasma-sprayed YSZ top coatings on superalloys X4, 1483, or 247 substrates. For both types of coatings exposed in 1-h cycles, the addition of water vapor resulted in a decrease in coating lifetime, except for Pt-diffusion coatings which were unaffected by the environment. In 100-h cycles, environment was less critical, perhaps because coating failure was chemical (i.e., due to interdiffusion) rather than mechanical. As a result, in both 1-h and 100-h cycles, CO 2 did not appear to have any negative effect on coating lifetime.
Interface Structure and Transport of Complex Oxide Junctions
The interface structure and magnetism of hybrid magnetic tunnel junction-spin filter devices have been investigated and correlated with their transport properties. Magnetic tunnel junctions made of a spinel NiMn2O4 tunnel barrier sandwiched by theoretically predicted half-metallic electrodes, perovskite La0.7Sr0.3MnO3 and spinel Fe3O4, exhibit very high crystalline quality as observed by transmission electron microscopy. Structurally abrupt interfaces allow for the distinct magnetic switching of the electrodes as well as large junction magnetoresistance. The change in the magnetic anisotropy observed at the spinel-spinel interface is indicative of a thin interdiffused magnetically soft interfacial layer. The strong exchange coupling at this interface allows for low background magnetoresistance, and a spin-filter effect with when the barrier is ferrimagnetic.
Enhanced interfacial thermal transport in pnictogen tellurides metallized with a lead-free solder alloy
Controlling thermal transport across metal–thermoelectric interfaces is essential for realizing high efficiency solid-state refrigeration and waste-heat harvesting power generation devices. Here, the authors report that pnictogen chalcogenides metallized with bilayers of Sn{sub 96.5}Ag{sub 3}Cu{sub 0.5} solder and Ni barrier exhibit tenfold higher interfacial thermal conductance Γ{sub c} than that obtained with In/Ni bilayer metallization. X-ray diffraction and x-ray spectroscopy indicate that reduced interdiffusion and diminution of interfacial SnTe formation due to Ni layer correlates with the higher Γ{sub c}. Finite element modeling of thermoelectric coolers metallized with Sn{sub 96.5}Ag{sub 3}Cu{sub 0.5}/Ni bilayers presages a temperature drop ΔT ∼ 22 K that is 40% higher than that obtained with In/Ni metallization. Our results underscore the importance of controlling chemical intermixing at solder–metal–thermoelectric interfaces to increase the effective figure of merit, and hence, the thermoelectric cooling efficiency. These findings should facilitate the design and development of lead-free metallization for pnictogen chalcogenide-based thermoelectrics.
High temperature operation to 500 °C of AlGaN graded polarization-doped field-effect transistors
AlGaN polarization-doped field-effect transistors were characterized by DC and pulsed measurements from room temperature to 500 °C in ambient. DC current-voltage characteristics demonstrated only a 70% reduction in on-state current from 25 to 500 °C and full gate modulation, regardless of the operating temperature. Near ideal gate lag measurement was realized across the temperature range that is indicative of a high-quality substrate and sufficient surface passivation. The ability for operation at high temperature is enabled by the high Schottky barrier height from the Ni/Au gate contact, with values of 2.05 and 2.76 eV at 25 and 500 °C, respectively. The high barrier height due to the insulatorlike aluminum nitride layer leads to an ION/IOFF ratio of 1.5 × 10 9 and 6 × 10 3 at room temperature and 500 °C, respectively. Transmission electron microscopy was used to confirm the stability of the heterostructure even after an extended high-temperature operation with only minor interdiffusion of the Ni/Au Schottky contact. The use of refractory metals in all contacts will be key to ensure a stable extended high-temperature operation.
Prospects for the expansion of standing wave ambient pressure photoemission spectroscopy to reactions at elevated temperatures
Standing wave ambient pressure photoemission spectroscopy (SWAPPS) is a promising method to investigate chemical and potential gradients across solid-vapor and solid-liquid interfaces under close-to-realistic environmental conditions, far away from high vacuum. Until now, these investigations have been performed only near room temperature, but for a wide range of interfacial processes, chief among them being heterogeneous catalysis, measurements at elevated temperatures are required. One concern in these investigations is the temperature stability of the multilayer mirrors, which generate the standing wave field. At elevated temperatures, degradation of the multilayer mirror due to, for example, interdiffusion between the adjacent layers, decreases the modulation of the standing wave field, thus rendering SWAPPS experiments much harder to perform. Here, we show that multilayer mirrors consisting of alternate B4C and W layers are stable at temperatures exceeding 600 °C and are, thus, promising candidates for future studies of surface and subsurface species in heterogeneous catalytic reactions using SWAPPS.
Comparative study on the formation of Cr and Ti ohmic contacts to (001) β -Ga 2 O 3
Here, a comparative study of Cr/Au and Ti/Au ohmic contacts on (001) β-Ga 2 O 3 was conducted. The electrical behavior from current-voltage measurements and the interfacial composition and microstructure as determined from high-resolution transmission electron microscopy (TEM) with energy dispersive x-ray analysis were compared for the different contacts at selected points in an annealing series (300–700 °C, 1 min. anneals in N 2 ). Cr/Au contacts became ohmic at temperatures (300–350 °C) approximately 50–100 °C lower than Ti/Au contacts (400–450 °C). Cr/Au and Ti/Au contacts demonstrated optimal ohmic behavior (lowest resistance) when annealed to 450–500 and 500–600 °C, respectively, with Ti/Au contacts yielding a lower total resistance than Cr/Au. Cross-sectional TEM images of Cr/Au contacts annealed at 450 °C revealed the presence of Au nanoclusters at the Ga 2 O 3 interface and CrO x layers at both the top of the contact and the Ga 2 O 3 interface. Whereas TiO x also formed at the top and bottom interfaces in 450 °C-annealed Ti/Au contacts, the TiO x surface layer appeared to be variable in thickness and/or discontinuous, unlike the CrO x surface layer. Au nanoclusters were not detected at the interface in the Ti/Au contacts. The interdiffusion and oxidation observed in both contact metallizations point to the need for diffusion barriers that may allow these contacts to be used in future Ga 2 O 3 -based devices that operate at elevated temperatures.
Effects of the lateral ordering of self-assembled SiGe nanoislands grown on strained Si{sub 1-x}Ge{sub x} buffer layers
Atomic-force microscopy, micro-Raman spectroscopy, and high resolution X-ray diffraction are applied to study the spatial ordering in single layers of SiGe nanoislands grown on a strained Si{sub 1-x}Ge{sub x} buffer sublayer. It is shown that, apart from stimulating the spatial ordering of nanoislands, the introduction of a Si{sub 1-x}Ge{sub x} sublayer leads to an enhanced role for interdiffusion processes. An unusually high increase in the volume of nanoislands in the process of the epitaxy is related to the anomalously strong diffusion from the buffer sublayer into the islands that is induced by nonuniform fields of elastic strains. The anisotropy of the islands shape and spatial ordering is discussed in terms of the anisotropy of the diffusion processes in spatially nonuniform fields of elastic strains.
Formation of the low-resistivity compound Cu{sub 3}Ge by low-temperature treatment in an atomic hydrogen flux
The systematic features of the formation of the low-resistivity compound Cu{sub 3}Ge by low-temperature treatment of a Cu/Ge two-layer system in an atomic hydrogen flux are studied. The Cu/Ge two-layer system is deposited onto an i-GaAs substrate. Treatment of the Cu/Ge/i-GaAs system, in which the layer thicknesses are, correspondingly, 122 and 78 nm, in atomic hydrogen with a flux density of 10{sup 15} at cm{sup 2} s{sup –1} for 2.5–10 min at room temperature induces the interdiffusion of Cu and Ge, with the formation of a polycrystalline film containing the stoichiometric Cu{sub 3}Ge phase. The film consists of vertically oriented grains 100–150 nm in size and exhibits a minimum resistivity of 4.5 µΩ cm. Variations in the time of treatment of the Cu/Ge/i-GaAs samples in atomic hydrogen affect the Cu and Ge depth distribution, the phase composition of the films, and their resistivity. Experimental observation of the synthesis of the Cu{sub 3}Ge compound at room temperature suggests that treatment in atomic hydrogen has a stimulating effect on both the diffusion of Cu and Ge and the chemical reaction of Cu{sub 3}Ge-compound formation. These processes can be activated by the energy released upon the recombination of hydrogen atoms adsorbed at the surface of the Cu/Ge/i-GaAs sample.