Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser ablation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The Magnitude and Waveform of Shock Waves Induced by X-ray Lasers in Water

The high energy densities deposited in materials by focused X-ray laser pulses generate shock waves which travel away from the irradiated region, and can generate complex wave patterns or induce phase changes. We determined the time-pressure histories of shocks induced by X-ray laser pulses in liquid water microdrops, by measuring the surface velocity of the microdrops from images recorded during the reflection of the shock at the surface. Measurements were made with ~30 µm diameter droplets using 10 keV X-rays, for X-ray pulse energies that deposited linear energy densities from 3.5 to 120 mJ/m; measurements were also made with ~60 µm diameter drops for a narrower energy range. At a distance of 15 µm from the X-ray beam, the peak shock pressures ranged from 44 to 472 MPa, and the corresponding time-pressure histories of the shocks had a fast quasi-exponential decay with positive pressure durations estimated to range from 2 to 5 ns. Knowledge of the amplitude and waveform of the shock waves enables accurate modeling of shock propagation and experiment designs that either maximize or minimize the effect of shocks.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

The Kinetics of Aragonite Formation from Solution via Amorphous Calcium Carbonate

Magnesium doped Amorphous Calcium Carbonate was synthesised from precursor solutions containing varying amounts of calcium, magnesium, H2O and D2O. The Mg/Ca ratio in the resultant Amorphous Calcium Carbonate was found to vary linearly with the Mg/Ca ratio in the precursor solution. All samples crystallised as aragonite. No Mg was found in the final aragonite crystals. Changes in the Mg to Ca ratio were found to only marginally effect nucleation rates but strongly effect crystal growth rates. These results are consistent with a dissolution-reprecipitation model for aragonite formation via an Amorphous Calcium Carbonate intermediate.

36 MATERIALS SCIENCE↗
DOE OSTI2022

FEMTOSECOND LASER DRILLING OF SILICON NITRIDE

Ceramics are employed in various engineering applications including electronics, semiconductors, automotive and aerospace industry, among others. Ceramics are desirable materials due to their high hardness, thermal resistance, chemical, thermal, and mechanical properties. A drawback of engineering ceramics is the manufacturing process. Ceramics are hard and brittle and conventional drilling or cutting methods can damage the material. These challenges in manufacturing have limited the application of ceramics in certain engineering applications. The non-contact machining of ceramics through ultrashort pulsed laser drilling offers a possible solution to the manufacturing issues. The advantage of laser drilling is the ability to machine hard and brittle materials. A laser, pulsed in the time regime of femtoseconds (fs), drills/machines sharp and well-defined holes and cuts. Additionally, the short pulse width results in limited melting, cracking, or heat transfer to the surrounding material, as well as no residual stresses. This non-contact process can greatly aid in the machining of hard materials. This study focuses on drilling into silicon nitride to produce zero-taper through holes. With this, other thicknesses can be explored, to achieve zero-taper holes.

Femtosecond laser ablation, Ceramics, Silicon Nitr↗
DOE OSTI2025

High Spatial Resolution Mapping of Retained Fission Gas

Fission gas isotopic analysis provides quantitative high precision determination of irradiated nuclear fuel burnup, offers diagnostic value, and informs fuel performance models. A measurement capability has been developed at Idaho National Laboratory (INL) for the release of retained fission gas using a focused laser and static noble gas mass spectrometry (MS) analysis. This high resolution (10s microns spot size) capability was demonstrated using Xe implanted metal foils.

07 - ISOTOPES AND RADIATION SOURCES↗
DOE OSTI2026

Synthesis and composition control of epitaxial FeWO4 thin films using pulsed laser deposition

We report the growth of epitaxial FeWO4 thin films on c-plane sapphire via pulsed laser deposition using a Fe 2 O 3 /WO 3 target ablated in an O 2 atmosphere. At a constant O 2 pressure of 1 mTorr, x-ray diffraction (XRD) confirms FeWO 4 as the major crystalline phase for substrate temperatures from 500 to 800 °C. As temperature increases, x-ray fluorescence (XRF) shows the Fe/W ratio remains nearly constant at 0.90 ± 0.02, while x-ray photoelectron spectroscopy (XPS) shows Fe 3+ to Fe 2+ conversion increases from 20% to 35%. Morphological analysis reveals phase separation, likely of amorphous Fe 3+ oxide from crystalline FeWO 4 , increasing with Fe 3+ conversion. This is attributed to an O-rich laser ablated flux, where conversion is driven by the Arrhenius temperature dependence of Fe 3+ → Fe 2+ reduction on the film surface. At a constant substrate temperature of 750 °C, XRD confirms FeWO 4 formation for O 2 pressures from 0.5 to 10 mTorr. As pressure increases, XRF shows the Fe/W ratio decreases from 0.98 to 0.70, while XPS shows Fe 3+ conversion rises from 15% to 70%. Morphology shows phase separation decreasing with increasing Fe 3+ conversion. This is attributed to scattering, where higher O 2 pressure makes the laser ablated flux O-deficient relative to Fe and W, facilitating Fe 2+ formation. Films with Fe 3+ conversion above ∼30% and Fe/W ratios from 0.86 to 0.96 exhibit FeWO 4 optical and electronic properties suitable for photoanode applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ablating nanoscale pores in crystalline quartz using laser-induced micro-plasmas in tri-layer structures

We demonstrate a novel approach for achieving rapid, consistent, and controllable micro-pore fabrication in single-crystalline quartz. These micro-pores are essential for applications in biology, i.e., studying ion channels in general and mechano-sensitive channels (MSC) in particular. The fabrication process consists of direct material ablation using pulsed UV light from a 193 nm excimer laser. These pulses ablate single-crystalline quartz chips by burning a laser-induced plasma in a tri-layer structure. Controllable plasma confinement and thus pore size is achieved by sandwiching a thin layer of a selected organic solution between the quartz chip and different substrates. This solution causes the confined micro-plasma to generate special ablation conditions, to create uniformly sized and shaped nanopores.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magnetized ICF implosions: Ignition at low laser energy using designs with more ablator mass remaining

This paper is the first work to redesign a spherical ICF implosion to best utilize the benefits of applying an external magnetic field. The sub-ignition experiment N170601 is taken as the baseline design, which used 1.57 MJ of laser energy. The optimum magnetized design benefits from increasing the shell thickness by 14 μ m and decreasing the ice thickness by 18 μ m, resulting in a neutron yield of 8.9 × 10 17 . This is 34 × greater than the unmagnetized simulation of the same design, and 18.5 × the greatest unmagnetized simulation across all designs simulated. The resultant implosion velocity for the magnetized design is lower, which would also reduce ablation front instability growth. This design was found by using a simplified 1D magnetization model and then validated against full 2D extended-MHD capsule simulations with radiation asymmetries applied to correct the shape.

Walsh, Christopher A. [Lawrence Livermore National↗
DOE OSTI2023

Exploration of cross-beam energy transfer mitigation constraints for designing an ignition-scale direct-drive inertial confinement fusion driver

The compression of direct-drive inertial confinement fusion (ICF) targets is strongly impacted by cross-beam energy transfer (CBET), a laser-plasma instability that limits ablation pressure by redirecting laser energy outward and that is projected to be mitigated by laser bandwidth. Here, we explore various CBET mitigation constraints to guide the design of future ICF facilities. First, we find that the flat, Gaussian, and Lorentzian spectral shapes have similar CBET mitigation properties, and a flat shape with nine spectral lines is a good surrogate for what can be obtained with other spectral shapes. Then, we conduct a comprehensive study across energy scales and ignition designs. 3D hydrodynamic simulations are used to derive an analytical model for the expected CBET mitigation as a function of laser and plasma parameters. From this model, we study the bandwidth requirements of conventional and shock ignition designs across four different energy scales and find that they require between 0.5 and 3±0.2% relative bandwidth. Further, best mitigation is achieved when the beam radius over critical radius R b /R c is kept low during the drive while the plasma temperature is kept high. In a steady state, we find that the bandwidth required to mitigate 85% of CBET scales as (R b /R c ) 2.15 L n –0.58 I 0.7 , where L n is the density scale length, and I the laser intensity. Finally, we find that the chamber beam port layout does not influence CBET mitigation. In the case of a driver using many monochromatic beamlets, we find that ~10 beamlets per port is required, with diminishing returns above ~20.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Performance of a liquid Ga target for Laser Ion Source

We experimentally proved the feasibility of a liquid-based target for Laser Ion Source (LIS) application. The target consists of melted metal gallium contained in a heated crucible. Ions current resulting from laser irradiation. Moreover, given the explosive ablation mechanism involved, each laser shot has been found to induce fluctuations in the surface level. It takes about 0.7 sec to recover the steady condition fully. Despite the maximum fluctuation being 2.7 mm (top-bottom maximum displacement), these fluctuations have shown no significant influence on total ion current and are independent of the temperature of the sample within the tested repetition rate. This study provides valuable insights into the potential of employing such a system for LIS.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Spatio-temporal ablation dynamics and plasma chemistry of aluminum induced by temporally modulated ytterbium fiber laser

Here, in this work, we studied single-pulse ablation dynamics of a temporally modulated continuous wave laser-material interaction with Al using in situ multimodal time-resolved diagnostics that describe in detail the associated physical and chemical processes. Time-resolved scattering, emission imaging, and optical emission spectroscopy unveiled a sequence of events spread out across three distinct phases: (i) early phase ablation process, associated with particle generation and liquid Al column formation (<20 μs), (ii) secondary detonation when sufficient ejected material is accumulated over the surface (20-50 μs), and (iii) molten liquid Al pool oscillation on the surface, followed by large droplet ejection from the liquid pool (100-500 μs). Atomic Al and AlO were observed with optical emission spectroscopy at different ratios during the entire lifetime of the event, verifying the formation of oxidized Al vapor upon its interaction with air. Morphological and compositional characterization confirmed surface oxidation and material re-solidification in the form of protrusions produced during the irradiation process. This work provides insights into the complex physical and chemical mechanisms of single-pulse ablation in the sub-millisecond laser pulse regime, which are critically important for parameter optimization in a variety of laser processing, microfabrication, and deposition applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Generation of shock trains in free liquid jets with a nanosecond green laser

Shock wave trains in liquid jets were previously generated only by ablation with femtosecond x-ray lasers. Here we show that shock trains in water microjets can be also generated using nanosecond green laser pulses with 1- to 10-mJ energy. Furthermore, the ablation of 15-, 20-, 30-, and 70-μm water microjets opened a gap in the jets and launched an initial shock wave. Fully developed shock trains were observed in the 30- and 70-μm jets up to 250-ns delays, and these trains were also transmitted inside the nozzles. A few tens of nanoseconds after the pulse, the shock dynamics and its pressure became similar to the ones generated by x-ray lasers, with a more rapid pressure decay in thinner jets. At time delays exceeding 100 ns in the 30-μm jets, the leading shock pressure stabilized to an approximately constant pressure of 40 MPa. The energy density deposited in the jets was estimated at 30 MJ/cm 3 by comparing the jet gaps in the green and x-ray laser experiments, and matched previous estimates for optical ablation in water. Here, the pressure decay in the 30-μm jets was modeled based on the pressure decay observed in x-ray laser experiments.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Laser Cutting and Micromachining for Localized and Targeted Solar Cell Characterization

Laser cutting and micromachining can be applied to solar cell materials for processing and characterization applications. An ultrashort pulse (USP) laser with sub-picosecond pulse width can remove material with minimal thermal effects or damage, which is termed `cold ablation'. Such USP laser cutting and scribing can be implemented for isolating areas within a larger cell while maintaining electrical performance and preventing laser-induced damage and shunting. Laser micromachining has been used to isolate a shunt to improve cell performance and to isolate a small, selected area to define a sample suitable for deep level transient spectroscopy.

14 SOLAR ENERGY↗
DOE OSTI2020

Laser power density dependence on charge state distribution of Ta ion laser plasma

Laser power density per pulse, which is commonly expressed with the unit of “W/cm2,” is an important parameter to characterize ablation plasma. To match a design charge state of heavy ion beam induced by a laser ion source, a laser power density must be carefully chosen. Above around 108 W/cm2 of laser power density, laser ablation plasma is emitted from the surface of solid material. Then, up to 109 W/cm2, the most abundant charge state is 1+. Because the ionization energy increases with higher charge states, increasing the laser intensity leads to the charge state distribution shifting higher. Increasing the density to increase charge states also results in lower time of flight due to higher velocities. The maximum laser power density is obtained by the smallest available laser spot size on the target material which is determined by the quality of the laser beam. For many accelerator applications, higher charge state beams are preferred. In particular cases, singly charge ion beams are demanded. Therefore, production of intermediate charge state beams has not been investigated well. In this study, we selected Ta4+ as an example demanded beam and tried to clarify how the transition of charge state distribution depends on laser power density. Conclusively, the possible specification of a laser ion source for Ta4+ delivery was elucidated.

Okamura, Masahiro (ORCID:0000000255521706)↗
DOE OSTI2023

Laser material interactions in tamped materials on picosecond time scales in aluminum

Here, a 100 ps laser is used to probe the pressure generation, depth of the non-solid ablator, and the non-linear optical effects through tamper materials. Samples consisted of an aluminum ablator with tampers of sapphire and coverslip glass. In general, the sapphire tamped sample achieves higher pressures at lower laser intensities as compared to the coverslip glass tamped sample. Attempts to model the details of this set of experimental data with standard available radiation coupled hydrodynamic codes make clear that more physics is needed in these simulations to accurately predict the impact of the tamper material on the pressure generation and the depth of non-solid aluminum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Optical spectroscopic tools for standoff uranium detection

Rapid and standoff analysis of uranium is important for many applications. We present the recent advances in standoff detection of uranium using emission and laser-induced fluorescence spectroscopy in conjunction with ultrafast laser filament ablation-based solid sampling.

(020.3260) Isotope shifts, (140.3440) Laser-induce↗
DOE OSTI2021

Talbot-Lau x-ray deflectometer: Refraction-based HEDP imaging diagnostic

Talbot-Lau x-ray interferometry has been implemented to map electron density gradients in High Energy Density Physics (HEDP) experiments. X-ray backlighter targets have been evaluated for Talbot-Lau X-ray Deflectometry (TXD). Cu foils, wires, and sphere targets have been irradiated by 10–150 J, 8–30 ps laser pulses, while two pulsed-power generators (∼350 kA, 350 ns and ∼200 kA, 150 ns) have driven Cu wire, hybrid, and laser-cut x-pinches. A plasma ablation front generated by the Omega EP laser was imaged for the first time through TXD for densities >1023 cm−3. Backlighter optimization in combination with x-ray CCD, image plates, and x-ray film has been assessed in terms of spatial resolution and interferometer contrast for accurate plasma characterization through TXD in pulsed-power and high-intensity laser environments. The results obtained thus far demonstrate the potential of TXD as a powerful diagnostic for HEDP.

Valdivia, M. P.↗