Search NASA⌕ Search

SEARCH · Search NASA

Results for “main engine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Space Shuttle Main Engine structural analysis and data reduction/evaluation. Volume 2: High pressure oxidizer turbo-pump turbine end bearing analysis

The high-pressure oxidizer turbopump (HPOTP) consists of two centrifugal pumps, on a common shaft, that are directly driven by a hot-gas turbine. Pump shaft axial thrust is balanced in that the double-entry main inducer/impeller is inherently balanced and the thrusts of the preburner pump and turbine are nearly equal but opposite. Residual shaft thrust is controlled by a self-compensating, non-rubbing, balance piston. Shaft hang-up must be avoided if the balance piston is to perform properly. One potential cause of shaft hang-up is contact between the Phase 2 bearing support and axial spring cartridge of the HPOTP main pump housing. The status of the bearing support/axial spring cartridge interface is investigated under current loading conditions. An ANSYS version 4.3, three-dimensional, finite element model was generated on Lockheed's VAX 11/785 computer. A nonlinear thermal analysis was then executed on the Marshall Space Flight Center Engineering Analysis Data System (EADS). These thermal results were then applied along with the interference fit and bolt preloads to the model as load conditions for a static analysis to determine the gap status of the bearing support/axial spring cartridge interface. For possible further analysis of the local regions of HPOTP main pump housing assembly, detailed ANSYS submodels were generated using I-DEAS Geomod and Supertab (Appendix A).

Sisk, Gregory A.↗
NASA NTRS1980

Space shuttle main engine digital controller

The controller provides responsive control of engine thrust and mixture ratio through the digital computer in the controller, updating the instructions to the engine control elements 50 times per second (every 20 milliseconds). Additionally, precise engine performance is achieved through closed loop control, utilizing 16 bit computation, 10 bit input/output resolution, and self calibrating analog-to-digital conversion. Engine reliability is enhanced by a dual redundant control system that allows normal operation after the first failure and a fail-safe shutdown after a second failure. The digital computer is programmable, allowing modification of engine control equations and constants by change of the stored program (software). The controller is packaged in a sealed, pressurized chassis with cooling provided by convection heat transfer through pin fins as part of the main chassis. The electronics are distributed on functional modules having special provisions for thermal and vibrational protection.

Mitchell, W. T.↗
NASA NTRS1993

Finite element analysis of the Space Shuttle Main Engine (SSME) alternate turbopump development (ATD) high pressure oxydizer turbopump (HPOTP)

A 3D model of all stationary components of the ATD HPOTP is analyzed using a superelement solution technique to obtain a better understanding of the pump behavior and to support pump testing. Emphasis is place on the methods used for determining deflections. As part of the model verification, analyses were conducted on the main housing model under proof-pressure and push-test loading conditions. The analysis at 109 percent rate power level resulted in asymmetric deformation patterns which were used to calculate operating and rub clearances. The present analysis is considered to provide the most realistic representation of the ATD HPOTP to date.

Ham-Battista, G. L.↗
NASA NTRS1973

Space shuttle main engine controller assembly, phase C-D

System design and system analysis and simulation are slightly behind schedule, while design verification testing has improved. Input/output circuit design has improved, but digital computer unit (DCU) and mechanical design continue to lag. Part procurement was impacted by delays in printed circuit board, assembly drawing releases. These are the result of problems in generating suitable printed circuit artwork for the very complex and high density multilayer boards.

Source record↗
NASA NTRS1973

The Space Shuttle Main Engine

A reusable high-performance rocket engine intended for putting the Space Shuttle orbiter vehicle into earth orbit is described. Three such engines are clustered in the aft end of the orbiter stage. They burn in parallel with the solid-propellant boosters during the initial ascent phase and continue to burn after booster ejection until just prior to orbit insertion. The nominal burn time is roughly 10 min. Propulsion requirements demand maximum performance from liquid oxygen/hydrogen propellants with a minimum hardware weight. The engine design and the present progress made in the development of the engine are discussed.

Castenholz, P. D.↗
NASA NTRS1971

Space shuttle main engine definition (phase B). Volume 2: Avionics

The advent of the space shuttle engine with its requirements for high specific impulse, long life, and low cost have dictated a combustion cycle and a closed loop control system to allow the engine components to run close to operating limits. These performance requirements, combined with the necessity for low operational costs, have placed new demands on rocket engine control, system checkout, and diagnosis technology. Based on considerations of precision environment, and compatibility with vehicle interface commands, an electronic control, makes available many functions that logically provide the information required for engine system checkout and diagnosis.

Source record↗
NASA NTRS1971

Space shuttle main engine definition (phase B). Volume 5: Valves and interconnects

The steady state thermodynamic cycle balance of the single preburner staged combustion engine, coupled with dynamic transient analyses, dictated in detail the location and requirements for each valve defined in this volume. Valve configuration selections were influenced by overall engine and vehicle system weight and failure mode determinations. Modulating valve actuators are external to the valve and are line replaceable. Development and satisfactory demonstration of a high pressure dynamic shaft seal has made this configuration practical. Pneumatic motor driven actuators that use engine pumped hydrogen gas as the working fluid are used. The helium control system is proposed as a module containing a cluster of solenoid actuated valves. The separable couplings and flanges are designed to assure minimum leakage with minimum coupling weight. The deflection of the seal surface in the flange is defined by finite element analysis that has been confirmed with test data. The seal design proposed has passed preliminary pressure cycling and thermal cycling tests.

Schultz, D. F.↗
NASA NTRS1980

Evaluation of space shuttle main engine bearings from high pressure oxygen turbopump 9008

Two used turbopump mainshaft support bearings were examined to determine steps needed to achieve turbopump lifetimes of 27,000 seconds. The two bearings, which had been run in a high pressure oxygen turbopump, are angular contact ball bearings, applied as a preloaded pair, locked to the shaft, inner race rotating, with the outer races unrestrained axially. Examination showed that both bearings had been subjected to overloads, leading to fatigue spalling on the races and balls and advanced retainer wear. This is clear evidence of unintended high internal loads in the high pressure oxygen pump which would lead to complete bearing failure and extensive secondary pump damage. Action must be taken to reduce the applied bearing loads or to incorporate bearings of sufficient size to withstand the high loads.

Dufrane, K. F.↗
NASA NTRS1980

Evaluation of axial lock-up of space shuttle main engine bearings from high pressure oxygen turbopump

The mainshaft support bearings of long life turbopumps for use on the space shuttle were evaluated to determine possible causes of failure. Specific aspects examined include the sensitivity of 15 degree versus 25 degree contact angle bearings with regard to heat damage and thermal runaway, the L/D aspects of the turbine end bearing pair with regard to hang-up due to cocking, the hang-up required to support a 44.5 KN axial load without cartridge slipping, the outer race growth as a result of a 44.5 KN axial load, and bearing torque as a function of axial load. Results indicate that hang-up of the cartridge due to bearing heating is a serious problem especially if poor lubrication of the bearing occurs and that race growth due to axial load can contribute to cartridge lock-up. The experimental evaluation of bearing performance under axial loads indicates that the bearing torque is a strong function of surface lubrication.

Kannel, J. W.↗
NASA NTRS1980

Rotordynamics analysis for the HPFTP (High Pressure Fuel Turbopump) of the SSME (Space Shuttle Main Engine). SSME turbopump technology improvements via transient rotordynamics analysis

The results of both linear (stability and synchronous response) and transient nonlinear analyses are reported. Dynamic coefficients were developed for the HPFTP interstage seals, and introduced into the rotordynamic model. The influence on HPFTP rotordynamics of a change in interstage seals from the smooth stepped design to a smooth straight configuration was examined. The sensitivity of the stability and synchronous results to changes in bearing stiffnesses and damping was determined. The influence on rotordynamic stability of a change from the stiff symmetric bearing carrier design to an asymmetric bearing carrier configuration was also studied.

Childs, D. W.↗
NASA NTRS1981

Study of methods for applying and enhancing transfer film coatings of polytetrafluoroethylene (PTEE) to Space Shuttle Main Engine (SSME) High Pressure Oxygen Turbo Pump (HPOTP) bearings

Machines were constructed and evaluated for burnishing polytetrafluoroethylene on balls for use in the high pressure oxygen turbopump (HPOTP). The most positive performance was obtained with single-ball burnishing, but one technique for burnishing three balls simultaneously holds promise. Evaluations of the coatings in a HPOTP bearing of earlier design (employed smaller diameter balls) showed very little life enhancement before high torque and ball and race wear initiated. Other coating techniques, such as molybdenum disulfide combined with PTFE transfer films, hold promise for providing the more durable quantities of solid lubricant needed for the bearings.

Kannel, J. W.↗
NASA NTRS1983

An inviscid three-dimensional analysis of the Space Shuttle main engine hot-gas manifold

A numerical study using an inviscid three-dimensional Lagrangian fluid dynamics code has been conducted as a part of an overall effort to understand the flow behavior in the SSME fuel side hot-gas manifold. The model simulates flow from the high-pressure fuel turbine exit through the transfer ducts, including the effects of swirl, inlet flow symmetry, and presence of straightening vanes and struts; a separate, more-detailed effort is in progress that includes viscosity and turbulence effects. The simplified model presented is divided into two parts, the first includes the 180-degree turnaround duct downstream of the turbine exit and the spherical fuel bowl section, while the second models the three transfer ducts. The two parts of the model are coupled together with the interface conditions being updated through iteration. Results indicate that a transverse pressure differential of 165 psi would be imposed on the turbine exit and that unstable flow separation occurs around the vanes, struts, and within the transfer ducts. The three transfer ducts show a mass flux split of approximately 41, 21, and 38 percent. Results to date are encouraging that certain flow characteristics can be usefuly represented using a relatively coarse grid inviscid code.

Liang, P. Y.↗
NASA NTRS1983

The analysis and testing of blade platform friction dampers used in the high pressure fuel turbopump (HPFTP) of the Space Shuttle Main Engine (SSME)

Premature cracking of the first stage turbine blades in HPFTP of the SSME could be alleviated by redesign of the platform friction dampers that are used to reduce the vibration response of the blades. Analytical studies by the lumped mass method of friction damper effectiveness and spin pit tests of a straingaged bladed disk have been performed. Methodologies used in the program are described. Preliminary results show that the effectiveness of the blade platform dampers can be increased if the frequency and amplitude of the most damaging forcing functions can be defined.

Dominic, R. J.↗
NASA NTRS1983

In-house welding studies supporting the prelaunch assessment of the STS-6 main engines

Welding studies were undertaken as a result of problems with the Challenger engines. The process used to perform these welds on heat exchanger coils, and sample test data, are described. Recommendations for process improvement are included. Effort to simulate problem welds, as well as good welds, test data, and conclusions for the high pressure fuel turbopump are also are discussed.

Hawkins, L. L.↗