Search NASA⌕ Search

SEARCH · Search NASA

Results for “method development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Evaluation of the ring tension test (RTT) for robust determination of material strengths

The ring tension test (RTT) is an experimental method for determining mechanical behavior in a material’s circumferential or hoop direction. It is a crucial test for testing anisotropic materials with tube geometry, such as nuclear fuel cladding or irradiated pipes. Several RTT configurations exist, each with their own advantages and disadvantages. However, this test is significantly more complex than traditional tensile testing and can be especially sensitive to small differences and inconsistencies in the test setup and geometry, ultimately affecting the derived mechanical properties. Previous research has focused on method development, and little work has been done on understanding the subtle differences between an ideal test and experiments, specifically when the tests are performed on highly irradiated materials in hot cells. In this work, a finite element-based investigation of the RTT is conducted to fill this gap. The two most used test configurations are investigated, comparing their ability to determine accurate material strengths through plastic deformation. Several non-ideal conditions and uncontrollable effects which are likely to occur during experimental testing such as machining tolerances, variations of specimen geometry from nominal dimensions, rotation of specimens and fixturing, and other test setup discrepancies are studied. The sensitivity of measured strengths to these conditions is presented. A mechanics-based approach to describing and correcting raw data to determine actual strengths is also included for one of the configurations, resulting in a robust correction method with highly accurate material strength measurements. Finally, based on these analyses, the hemicylindrical mandrel configuration is recommended with a gauge region oriented at a 45° angle.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Afterpulse correction for micro-pulse lidar to improve middle and upper tropospheric aerosol measurements

Micro-pulse lidar (MPL) measurements have been widely used in atmospheric research over the past few decades. However, the MPL afterpulse noise has a large impact on the MPL aerosol measurement in the middle and upper troposphere, and an effective correction method is still lacking. Here, a new afterpulse correction approach is presented by using measurements with low-level optically thick clouds to act as the lids blocking atmospheric signals beyond the clouds completely. Examples are provided to illustrate the effectiveness of this correction method. Using one-year 2014 MPL measurements at the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) site, the impact of the correction on the aerosol measurements is quantified. The relative error (RE, %) of attenuated backscattering ratio (ABR) without the afterpulse correction is 30% and 190% at the height of 1.00 km and 9.00 km (AGL), and the RE is larger for weaker aerosol signals (ABR<2). The RE of linear depolarization ratio (LDR), which is significantly higher than that of ABR for a given aerosol layer, is highly non-linear above 3.00 km, with a value of 300%-900% for weak aerosols (ABR<2) above 3.00 km. Therefore, the afterpulse correction is critical for the middle and upper tropospheric aerosol observations. We demonstrated that our afterpulse correction can provide reasonable particle depolarization ratio (PDR) to properly identify dust aerosols. The newly developed method can be applied to long-term MPL measurements to support aerosol and mixed-phase/ice cloud interaction study at the NSA site.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Intensity modulated Ir-192 brachytherapy using high-Z 3D printed applicators

Gynecologic cancers are often asymmetric, yet current Ir-192 brachytherapy techniques provide only limited radial modulation of the dose. The shielded solutions investigated here solve this by providing the ability to modulate between highly asymmetric and radially symmetric dose distributions at a given location. To find applicator designs that can modulate between full dose and less than 50% dose, at the dimensions of the urethra, a 2D calculation algorithm was developed to narrow down the search space. Two shielding design types were then further investigated using Monte Carlo and Boltzmann-solver dose calculation algorithms. 3D printing techniques using ISO 10993 certified biocompatible plastics and 3D printable tungsten-loaded plastics were tested. It was also found that shadowing effects set by the shape of the shielding cannot be easily modulated out, hence careful design is required. The shielded applicator designs investigated here, allow for reduction of the dose by over 50% at 5 mm from the applicator surface in desired regions, while also allowing radially symmetric dose with isodose line deviations less than 0.5 mm from circular. The shielding designs were also chosen with treatment delivery time in mind. Treatment times for these shielded designs were found to be less than 1.4 times longer than a 6-channel unshielded cylinder for the equivalent fully symmetric dose distribution. The 2D calculation methods developed here provide a simple way to rapidly evaluate shielding designs, while the 3D printing techniques also allow for devices with novel shapes to be rapidly prototyped. Both TOPAS Monte Carlo and Acuros BV calculations show that significant dose shaping and organ at risk sparing can be achieved without significantly compromising the plan in regions that require the full dose.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

The DESI One-Percent Survey: A Concise Model for the Galactic Conformity of Emission-line Galaxies

Galactic conformity is the phenomenon whereby a galaxy of a certain physical property is correlated with its neighbors of the same property, implying a possible causal relationship. Here, the observed auto correlations of emission-line galaxies (ELGs) from the highly complete DESI One-Percent Survey exhibit a strong clustering signal on small scales, providing clear evidence for the conformity effect of ELGs. Building upon the original subhalo abundance-matching (SHAM) method developed by Gao et al., we propose a concise conformity model to improve the ELG–halo connection. In this model, the number of satellite ELGs is boosted by a factor of ~5 in the halos whose central galaxies are ELGs. We show that the mean ELG satellite number in such central halos is still smaller than 1 and that the model does not significantly increase the overall satellite fraction. With this model, we can well recover the ELG auto correlations to the smallest scales explored with the current data (i.e., r p > 0.03 Mpc h –1 in real space and at s > 0.3 Mpc h –1 in redshift space), while the cross correlations between luminous red galaxies and ELGs are nearly unchanged. Although our SHAM model has only eight parameters, we further verify that it can accurately describe the ELG clustering in the entire redshift range from z = 0.8 to 1.6. We therefore expect that this method can be used to generate high-quality ELG lightcone mocks for DESI.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Robustness of Deep Learning Classification to Adversarial Input on GPUs: Asynchronous Parallel Accumulation Is a Source of Vulnerability

The ability of machine learning (ML) classification models to resist small, targeted input perturbations—known as adversarial attacks—is a key measure of their safety and reliability. We show that floating-point non associativity (FPNA) coupled with asynchronous parallel programming on GPUs is sufficient to result in misclassification, without any perturbation to the input. Additionally, we show that this misclassification is particularly significant for inputs close to the decision boundary and that standard adversarial robustness results may be overestimated up to 4.6 when not considering machine-level details. We first study a linear classifier, before focusing on standard Graph Neural Network (GNN) architectures and datasets used in robustness assessments. We develop a novel black-box attack using Bayesian optimization to discover external workloads that can change the instruction scheduling which bias the output of reductions on GPUs and reliably lead to misclassification. Motivated by these results, we present a new learnable permutation (LP) gradient-based approach to learning floating-point operation orderings that lead to misclassifications. The LP approach provides a worst-case estimate in a computationally efficient manner, avoiding the need to run identical experiments tens of thousands of times over a potentially large set of possible GPU states or architectures. Finally, using instrumentation-based testing, we investigate parallel reduction ordering across different GPU architectures under external background workloads, when utilizing multi-GPU virtualization, and when applying power capping. Our results demonstrate that parallel reduction ordering varies significantly across architectures under the first two conditions, substantially increasing the search space required to fully test the effects of this parallel scheduler-based vulnerability. These results and the methods developed here can help to include machine-level considerations into adversarial robustness assessments, which can make a difference in safety and mission critical applications.

Shanmugavelu, Sanjif [Maxeler Technologies, a Groq↗
DOE OSTI2025

Order-by-order uncertainties of nucleon-nucleon Wolfenstein amplitudes in chiral effective field theory

Quantum mechanical invariance principles dictate the most general operator structure that can be present in the nucleon-nucleon (NN) interaction. Five independent operators appear in the on-shell NN amplitude together with five corresponding coefficient functions. The usual choice for these coefficient functions is known as the NN Wolfenstein amplitudes. We analyze the order-by-order convergence of each of the five NN Wolfenstein amplitudes predicted by a semilocal coordinate space potential implementation of chiral effective field theory (𝜒⁢EFT). We do this at laboratory kinetic energies between 25 and 200 MeV for both neutron-proton and proton-proton scattering. Our analysis uses the Gaussian-process methods developed by the BUQEYE Collaboration to describe the contributions of each 𝜒⁢EFT order, and so yields truncation uncertainties for each Wolfenstein amplitude that are correlated across scattering angles. We combine information on the size of different orders in the EFT to infer the 𝜒⁢EFT breakdown scale for each amplitude, finding, on average, Λ 𝑏 between 750 and 800 MeV. Furthermore, with this choice of Λ 𝑏 , the EFT truncation uncertainties cover both higher-order results and empirical Wolfenstein amplitudes well for all orders other than the leading order.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Strong-field nonsequential double photoionization using virtual-detector theory with path summation

We present an ab initio study of the nonsequential strong-field ionization dynamics of a model two-electron atom with helium character. Single- and double-ionization events are characterized and displayed using detector signals extracted at different points in the two-electron two-dimensional space. The double photoelectron momentum distribution is calculated via coherent path-summation over virtual-particle trajectories. A comparison is made between the momentum distributions obtained with the virtual-detector method, the Schrödinger wave function, and the time-dependent surface flux method developed by Tao and Scrinzi [New J. Phys. 14, 013021 (2012)]. Insights into different ionization and electron recollision pathways are gained from detailed virtual-particle tracking and energy-time readouts. Furthermore, this study demonstrates the extension of virtual-detector theory to strong-field multielectron quantum dynamics and highlights the importance of the evolving quantum phase in quasiclassical electron propagation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Computational Aspects of Single-Molecule Kinetics for Coupled Catalytic Cycles: A Spectral Analysis

Catalysis from single active sites is analyzed using methods developed from single molecule kinetics. Using a stochastic Markov state description, the observable properties of general catalytic networks of reactions are expressed using an eigenvalue decomposition of the transition matrix for the Markov process. By the use of a sensitivity analysis, the necessary eigenvalues and eigenvectors are related to the energies of controlling barriers and wells located along the reaction routes. A generalization of the energetic span theory allows the eigenvalues to be computed from several activation energies corresponding to distinct barrier-well pairings. The formalism is demonstrated accurately for model problems for a physically realistic mechanism for an alkene hydrogenation reaction on a single atom catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

P SI4 1.4: Open-source software for high-throughput quantum chemistry

PSI4 is a free and open-source ab initio electronic structure program providing implementations of Hartree–Fock, density functional theory, many-body perturbation theory, configuration interaction, density cumulant theory, symmetry-adapted perturbation theory, and coupled-cluster theory. Most of the methods are quite efficient, thanks to density fitting and multi-core parallelism. The program is a hybrid of C++ and Python, and calculations may be run with very simple text files or using the Python API, facilitating post-processing and complex workflows; method developers also have access to most of PSI4 's core functionalities via Python. Job specification may be passed using The Molecular Sciences Software Institute (MolSSI) QCSCHEMA data format, facilitating interoperability. We announce a rewrite of our top-level computation driver, and concomitant adoption of the MolSSI QCARCHIVE INFRASTRUCTURE project, makes the latest version of PSI4 well suited to distributed computation of large numbers of independent tasks. The project has fostered the development of independent software components that may be reused in other quantum chemistry programs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Development of Scalable Coastal and Offshore Macroalgal Farming

The US DOE/ARPA-E MARINER program funded a four-year project to determine an optimal way to grow kelps in large, nearshore and offshore arrays for the eventual purpose of biofuel production with the goal of keeping the cost below $\$$80 USD per dry metric ton of kelp. This project specifically looked at how Saccharina latissima can be grown in the Gulf of Alaska to reach that goal. There were three major aspects of the research: 1) optimizing nursery production and seeding lines for outplanting, 2) designing an economical, modular outplanting structure and 3) developing methods to efficiently harvest the product. Farm designs were based on catenary structures and the use of spreader bars with variable spacing of grow lines and line types. The spacing of the grow lines makes a difference in the yield. Grow line spacing of ≥1.5m showed about a 50% increase in kg/m. There was no statistical difference in the growth of Saccharina latissima whether in the middle or the outside of the array, but the line type and perhaps line thickness can make a difference in yield. Sagging caused by the weight of the mature fronds resulted in lower growth at depth. Various harvesting approaches for mature kelps were tested by collaborating farmers. One promising innovation is the use of large bags for holding the freshly harvested fronds. Although the weight of the fronds on the growlines causes the lines to sink, the bags packed with the harvested fronds float, allowing for easy loading to the transfer vessel. Another advance in harvesting is a specially built harvest vessel, the Harvest Buddy, allowing a more mechanized and faster way to harvest. A significant aspect of this project was the TTO/T2M. Several different outreach activities were performed by the Alaska Fisheries Development Foundation and GreenWave. A techno-economic assessment (TEA) using our data has pointed to solutions to reach the $\$$80 goal. A second phase of this project involved the co-culture of two different species of kelps. Interest in farming kelps has grown beyond using kelp for food, feed or biofuels. There is considerable interest in generating biomass from seaweed for use in bioplastics and other products that would substitute for petroleum-derived products. For these uses to be viable, large amounts of biomass are needed. Very large kelp farms can be expensive to build and maintain, leading to the need to optimize the biomass per unit area. Although close spacing of growlines can lead to poor growth, a viable approach may be to grow two species of kelps together: one that hangs down and one that is buoyant, growing up. This system would increase the spacing in three dimensions. In Alaska, Saccharina latissima is commonly grown hanging down from longlines. One of the buoyant Alaskan kelps is Nereocystis luetkeana. Because there are commercial uses for wild-harvested Nereocystis in Alaska, we undertook a preliminary trial in Kodiak, Alaska that grew both Saccharina and Nereocystis in the same longline array. Closely spaced lines were seeded the first week of February 2023 and set at 3m below the surface. The arrays were harvested in late June 2023. Despite having 45% fewer grow-lines, the total yield of the Nereocystis on the combined arrays was statistically similar to the Nereocystis only arrays. Total yields were greatest on the combined arrays, followed by the Nereocystis only and Saccharina only arrays. These results may have significance for large scale macroalgal production.

09 BIOMASS FUELS↗
DOE OSTI2025

Atacama Cosmology Telescope: DR6 gravitational lensing and SDSS BOSS cross-correlation measurement and constraints on gravity with the 𝐸 𝐺 statistic

We derive new constraints on the 𝐸 𝐺 statistic as a test of gravity, combining the cosmic microwave background (CMB) lensing map estimated from Data Release 6 (DR6) of the Atacama Cosmology Telescope with Sloan Digital Sky Survey III Baryon Oscillation Spectroscopic Survey (SDSS BOSS) CMASS and LOWZ galaxy data. We develop an analysis pipeline to measure the cross-correlation between CMB lensing maps and galaxy data, following a blinding policy and testing the approach through null and consistency checks. By testing the equivalence of the spatial and temporal gravitational potentials, the 𝐸 𝐺 statistic can distinguish Λ⁢ CDM from alternative models of gravity. We find 𝐸 𝐺 ⁡(𝑧 eff = 0.555) = 0.3⁢1$^{+0.06}_{−0.05}$ for Atacama Cosmology Telescope (ACT) and CMASS data at 68.28% confidence level, and 𝐸 𝐺 ⁡(𝑧 eff = 0.316) = 0.4⁢9$^{+0.14}_{−0.11}$ for the ACT and LOWZ. Systematic errors are estimated to be 3% and 4%, respectively. Including CMB lensing information from Planck PR4 results in 𝐸 𝐺 ⁡(𝑧 eff = 0.555) = 0.3⁢4$^{+0.05}_{−0.05}$ with CMASS and 𝐸 𝐺 ⁡(𝑧 eff = 0.316) = 0.4⁢3$^{+0.11}_{−0.09}$ with LOWZ. These are consistent with predictions for the Λ⁢ CDM model that best fits the Planck CMB anisotropy and SDSS BOSS baryon acoustic oscillations (BAO), where 𝐸$^{GR}_{𝐺⁡}$(𝑧 eff =0.555) =0.401 ± 0.005 for CMB lensing combined with CMASS and 𝐸$^{GR}_{𝐺}$⁡(𝑧 eff = 0.316) = 0.452 ± 0.005 combined with LOWZ. We also find 𝐸 𝐺 to be scale independent, with probability to exceed >5%, as predicted by general relativity. The methods developed in this work are also applicable to improved future analyses with upcoming spectroscopic galaxy samples and CMB lensing measurements.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Micro-Quantification of Helium-3 and Helium-4 in TPBAR Components

This report documents the method development for measuring helium isotopes in micrometer-sized samples of tritium producing burnable absorption rod (TPBAR) components. Helium isotopes were measured as a tracer for tritium, which decays to 3 He with a half-life of 12.33 years. Getter and cladding materials from the TPBARs were analyzed, as they are designed to trap tritium. Therefore, constraining the diffusivity of tritium through these materials is of key importance. To first establish the reliability of the noble gas mass spectrometer, a reference gas with a relative 4 He/ 3 He ratio of 1000 was pre-mixed. This standard was measured several times to ensure measurements were reproducible. Unirradiated and irradiated getter and cladding samples of TPBARs were cut into 1-100 µm 3 cubes and analyzed for 3 He and 4 He content. The unirradiated materials had helium content equal to or less than that of the measured instrument background. Irradiated cladding also had instrument background levels of helium while irradiated getters had elevated levels of 3 He, interpreted to be the decay product of tritium. No diffusion of 4 He was observed in any of these materials, however, indicating that the 3 He detected in the irradiated getter was produced in situ after tritium diffusion and decay. These findings validate this method as a way to trace tritium diffusion in reactor materials.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2025

In-Silico Design of Next Generation Cellulose-Derived Packaging Materials (CRADA Final Report)

Developing sustainable solutions for single-use packaging is an important objective to combat the environmental crisis of plastics pollution. Most embodiments of cellulose-based packaging materials, including CellophaneTM, are completely biodegradable in both terrestrial and marine environments. However, petroleum-derived alternatives offer some performance advantages for metrics such as moisture barriers and mechanical properties. This project leverages molecular dynamics simulation to investigate how molecular modifications to cellulose-based polymer assemblies impact their material properties. An important performance criterion for the modified materials was to retain biodegradability; thus, modifications by naturally occurring, biodegradable additives were the focus of this study. Specifically, we developed models with xylan and lignin of varying monomeric compositions into the cellulose matrix. The mechanical properties were investigated by performing stress-strain simulations, and the water barrier and hydrophobicity were investigated by simulating the water contact angle. Our findings indicate that the incorporation of xylan into the cellulose matrix tends to increase the mechanical properties with an optimal loading of ~27 wt%. We also predict that orienting the nanoscale directionality of the xylan chains such that they are perpendicular to the cellulose fibrils will dramatically increase mechanical strength. In contrast, the incorporation of lignin tends to weaken the composite at all loadings investigated. Simulations of water contact angle predicted that coating polymers on the surface of the cellulose assembly creates a more hydrophobic surface than incorporating them throughout the matrix. Of the coatings investigated, lignin resulted in the most hydrophobic surface, followed by pectin and keratin, which both imparted modest increases in hydrophobicity. Future experimental work done by Futamura will focus on designing material prototypes to capitalize on the predictions of performance enhancement obtained from molecular modeling. While substantial progress was made by the simulations performed in this project, there still exists a vast parameter space that we were unable to investigate, including branching, functional group decoration, and degree of polymerization of polymer additives. However, the methods developed in this initial investigation will facilitate more rapid evaluation of the impact of molecular characteristics on the performance of biopolymer composite materials and thereby accelerate future materials discovery efforts in this area.

36 MATERIALS SCIENCE↗
DOE OSTI2022

BESTEST-GSR (Building Energy Simulation Test - Generation Simulation and Reporting) 2023 [SWR 18-23]

Building Energy Simulation Test (BESTEST) is an NREL-developed method to validate the qualitative performance of different whole building simulations engines relative to each other. https://www.nrel.gov/docs/legosti/old/6231.pdf The purpose of this repository is to generate BESTEST test case models, run simulations, and populate data for ASHRAE Standard 140 reporting spreadsheets for EnergyPlus® based whole building simulation tools. It was originally setup for 2014 version of Standard 140. In May of 2022 it was updated to the 2020 version of Standard 140. This update included updates and additions to existing test suites, the bulk of which was in Section 5.2 (Building Thermal Envelope and Fabric Load Tests). We did not add Section 5.5 Airside HVAC Equipment Performance, but we hope to add that later in 2022. At some point we also hope to add Section 5.2.4 ground modeling, which is currently excluded. Supported Tools The default IDF generation is based on the OpenStudio® CLI, but the workflow supports a 'Bring your own IDF' use case. Additionally, for non-EnergyPlus® based tools the post processing scripts can be used if simulation results are provided as a CSV file.The scripts on this repository should work on Mac, Windows, and Linux. Dependencies Install OpenStudio® 3.4.0 make sure command line can recognize the 'openstudio' command This includes EnergyPlus® 22.1 Install Ruby on your system if it isn't already setup. 2.7 is used for development but other versions may work Since OpenStudio has its own embedded Ruby, which is used for running measures, you don't necessarily have to use a version of Ruby supported by OpenStudio. Install RubyXL Ruby gem This is used to modify Microsoft Excel spreadsheets Install Parallel Ruby gem This allows the CLI to run simulations in parallel

Goldwasser, David↗
DOE OSTI2020

Unsaturated and Saturated Hydraulic Parameters of Soils at the East River Watershed, Colorado Calculated using the Pedotransfer Function Method.

The purpose of the data package is to present the results of calculations of the following unsaturated-saturated hydraulic parameters of soils of the East River Watershed, Colorado: fully saturated water content (Qs), residual saturation (Qr), van genuchten parameters alpha and n, field capacity (FC), and saturated hydraulic conductivity (Ks). Calculations were conducted for the following soil texture types: sandy_loam, loam, silty_clay_loam, clay_loam, silt loam; the particle size distribution included the percentage of sand, silt, clay, and the bulk density (BD) of soils. Calculations were conducted for the following areas- Lower_Subalpine (6 samples),- Lower_Montane_lower_hillslope (7 samples),- Floodplain_at_base_of_lower_montane_hillslope, (11 samples),- PLM-0 (10 samples),- PLM-1 (10 samples), and - PLM-3 (13 samples)Calculations were conducted using the Pedotransfer Function Method developed by Tóth et al. (2014) with the application of the code ”euptf” in Rstudio. The data are being summarized in the Excel file ”Unsaturated_Saturated_Hydraulic_Parameters_PTF_calculated_EASt_EIver.xls" including two worksheets:“full_data_EAST_RIVER” which includes (a) the input data used for calculations, the soil texture triangle, and the plots of the water retention curves and unsaturated hydraulic conductivity for several types of soil texture, and (b) the summary table with the averaged parameters for each area. The the texture triangle was plotted using the Rstudio "soiltexture." Microsoft Excel software is required to open the Excel file. The metadata and a list of references to the Rstudio libraries used for calculations and data visualization are giving in the Word Readme file.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Artificial Soiling Replication of Field Losses on Commercial Photovoltaic Modules

Here, this study demonstrates the capabilities of an indoor artificial soiling approach developed to closely replicate the natural, cyclic soil accumulation processes in the field-dust suspension, deposition, and sedimentation/cementation-for a subtropical climate. In this work, a near-field environment is replicated in an artificial soiling cubic chamber through controlled regulation of humidity, temperature, dust type, and dust concentration, based on site-specific historical climate data. Two different models (MA and MB) of full-size commercial photovoltaic modules from a single manufacturer, installed side by side in the mid-Atlantic United States, were retrieved and subjected to artificial soiling experiments and various characterization measurements, including short-circuit current, colorimetry, reflectance, X-ray fluorescence, laser diffraction, and optical microscopy. Both in the field and in our improved field-representative artificial soiling tests, the MA model experienced roughly twice the soiling loss as the MB model. To closely replicate the field soiling losses for a site-specific climate, it is critical to include: 1) The use of field-collected dust with identical dust chemistry and particle distribution instead of standardized ISO 12103 Arizona Road dusts, 2) the use of only a small amount of field-collected dust inside the chamber during the deposition process (e.g., 0.15 g), and 3) the preconditioning of the surface coating for the partial/full dose of UV stress as experienced in the field during sunlight exposure and the abrasion as experienced in the field during regular module cleaning activities, if/as needed. The field-representative artificial soiling method developed here could potentially be adopted for rank ordering of various antisoiling coatings developed by researchers and industry stakeholders.

14 SOLAR ENERGY↗
DOE OSTI2025

Extreme Ultraviolet and Beyond Extreme Ultraviolet Lithography Using Amorphous Zeolitic Imidazolate Resists Deposited by Atomic/Molecular Layer Deposition

Amorphous zinc-imidazolate (aZnMIm) resists show potential to meet the demands for next-generation high-numerical aperture (high-NA) metal-containing extreme ultraviolet (EUV) resist materials, given their ease of deposition by atomic/molecular layer deposition (ALD/MLD) at thicknesses of 20 nm and below. Here, this study demonstrates that aZnMIm thin films, previously identified as high-resolution electron beam resists, can also function as negative-tone EUV photoresists. Water development achieves high sensitivity (5 mJ/cm 2 ) but leaves significant residue, while acetic acid development results in poor contrast. A hybrid approach─water followed by acetic acid─enables residue-free development with a sensitivity of 181 mJ/cm 2 . Dry development using 1,1,1,5,5,5-hexafluoroacetylacetone (hfacH) is also possible but shows lower sensitivity (375 mJ/cm 2 ) compared to wet development methods. EUV photoelectron spectroscopy (PES), reflectometry/EUV absorption, total electron yield (TEY), residual gas analysis (RGA), and time-of-flight secondary ion mass spectrometry (TOF-SIMS) were used to investigate the effects of EUV irradiation on aZnMIm resists. Reflectometry experiments reveal an aZnMIm EUV absorption coefficient of 6.2 μm –1 , while PES and TEY analyses show that, compared to poly(4-hydroxystyrene) (PHS), a polymer-based reference resist, aZnMIm emits more primary and secondary electrons but generates fewer slow electrons relative to its primary electron emission; its total electron yield is similar to that of poly(methyl methacrylate) (PMMA) resists. When exposed to EUV, aZnMIm predominantly outgasses H 2 , as determined by RGA. TOF-SIMS measurements demonstrate that high-dose EUV exposure only partially fragments the 2-methylimidazole (2MIm) organic linkers, unlike high-dose electron beam exposure, which is known to completely degrade them. Additionally, aZnMIm resists show promise for potential beyond EUV lithography (BEUVL) due to the presence of Zn, which provides higher sensitivity at a wavelength of 6.7 nm compared to other metal ions, such as Sn, that are currently used in the best-performing EUV metal–organic resists. TEY measurements demonstrate that aZnMIm emits nearly twice as many electrons as PHS at 6.7 nm. The BEUV TEY of aZnMIm also surpasses that of PMMA, poly(pentafluorostyrene), and poly(4-iodostyrene), with the latter two being known for their high EUV TEYs. This work provides insight into zeolitic imidazolate framework (ZIF)-based EUV and BEUV resists and highlights their potential for both wet and dry development.

lithography↗
DOE OSTI2021

Soft X-ray measurements of transport and MHD activity in the core and edge NSTX plasma (Final Technical Report)

A comprehensive suite of innovative diagnostic instrumentation and techniques has been developed by the Johns Hopkins collaboration for measurements of transport and MHD activity in the core and edge of the National Spherical Torus Experiment (NSTX) at the Princeton Plasma Physics Laboratory (PPPL). These include ultrafast multi-energy poloidal soft X-ray arrays, high spatial resolution multi-energy tangential soft X-ray arrays, high spectral resolution transmission grating imaging VUV spectrometers and ultrafast bolometric arrays, which measure over a broad range of spatial, spectral, and temporal scales the emission from ohmic, RF, and beam driven NSTX plasmas. The instrumentation was designed to fulfill the specific measurement needs of the Spherical Torus (ST) magnetic fusion concept and is accompanied by a comprehensive set of numerical tools for data analysis and modeling, aimed at determining as many as possible plasma parameters and at extracting as much as possible physics information from NSTX experiments. The Johns Hopkins diagnostics have been and continue to be instrumental for essentially all the NSTX experiments. In addition, our own research and experiments using these diagnostics has led over the years to fundamental conclusions for the ST fusion physics, such as the establishment of near neoclassical impurity transport in the NSTX core and edge plasma, and the critical role of the Global Alfven Eigenmode (GAE) MHD activity for the ST core electron thermal transport. The Johns Hopkins Diagnostics continue to be operational on the upgraded NSTX-U and will provide key plasma information in its upcoming high field, current and power experimental campaigns. The present report summarizes the main technical characteristics and measurement capabilities of the diagnostic instrumentation and methods developed within our research and describes a key physics result achieved during this research. Success in our research was made possible also by the excellent support and cooperation of the NSTX research team and of PPPL researchers, who are warmly acknowledged here.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗