Search NASA⌕ Search

SEARCH · Search NASA

Results for “misalignment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Orbital precession in Hercules X-1

It is noted that the 35-day X-ray high-low cycle of Her X-1 could be explained in terms of periodic obscuration of the source by a tilted and precessing 'slaved' accretion disk, which would require precession of the mass-shedding star and, consequently, a precessing binary orbit. Four months of Uhuru data obtained in 1972 are analyzed to determine whether the orbital precession can be detected as a Doppler modulation in the arrival times of the 1.24-sec X-ray pulsations. The precession geometry is examined, the test for precession is outlined, and a marginally significant indication of orbital precession in the Hz Her/Her X-1 system is obtained. Possible biases in the analysis are evaluated, and the spin-axis misalignment of HZ Her is estimated from the measured tilt of the orbit.

Deeter, J. E.↗
NASA NTRS1977

Experimental study of error sources in skin-friction balance measurements

An experimental study has been performed to determine potential error sources in skin-friction balance measurements. A floating-element balance, large enough to contain the instrumentation needed to systematically investigate these error sources has been constructed and tested in the thick turbulent boundary layer on the sidewall of a large supersonic wind tunnel. Test variables include element-to-case misalignment, gap size, and Reynolds number. The effects of these variables on the friction, lip, and normal forces have been analyzed. It was found that larger gap sizes were preferable to smaller ones; that small element recession below the surrounding test surface produced errors comparable to the same amount of protrusion above the test surface; and that normal forces on the element were, in some cases, large compared to the friction force.

Allen, J. M.↗
NASA NTRS1977

Control and stability problems of remote orbital capture

Certain space shuttle missions may require retrieval of passive spinning and precessing satellites. One proposed means of retrieval utilizes a free-flying teleoperator launched from the shuttle. A study of misalignment, stability, and certain control aspects during capture of an object is reported here. The approach used is to model the dynamics by a Lagrangian formulation and apply torque components to dissipate motion. Differential angular rates between teleoperator and object are assumed, and control responses after capture are reviewed.

Kaplan, M. H.↗
NASA NTRS1978

The forward scattering of microwave solar radiation from a water surface

The forward scattering of microwave solar radiation from both smooth and rough water surfaces is computed. The smooth surface is assumed specular, and the rough surface is represented by a two-scale surface, for which two small-scale perturbation parameters, 0.10 and 0.25, are considered. The contribution of the scattered sunlight to the antenna temperature is found using the scalar approximation, and the results are compared with radiometer measurements. The overall agreement is good, but in some cases the smooth-surface measurements are higher than the computations. This discrepancy possibly indicates an absolute calibration error or a slight misalignment of the antennas' boresights. The computations for the two perturbation parameters bracket the rough-surface measurements except when the sun's mirror image is far removed from the boresight direction. The small disagreement in this case may be due to a peaked large-scale slope distribution.

Wentz, F. J.↗
NASA NTRS1978

Load-displacement measurement and work determination in three-point bend tests of notched or precracked specimens

Suggestions for testing of notched or cracked three-point bend specimens are presented that (1) correct displacement measurement errors resulting from misalignment between the load applicator and specimen; (2) account for coincidental strains not associated with the work of crack extension; (3) simplify record analysis and processing; and (4) extend displacement gage range without sacrifice of sensitivity or accuracy. These testing details are particularly applicable to procedures in which the crack extension force J(I) is determined from the work done on the specimen.

Buzzard, R. J.↗
NASA NTRS1977

Design considerations in mechanical face seals for improved performance. II - Lubrication

The importance of sealing technology in the U.S. industrial chemical-orientated society in regard to maintenance and environmental contamination is pointed out. It is stated that seal performance (leakage, life) is directly related to seal lubrication, which is a mechanism not well understood. Current thinking in regard to seal lubrication is reviewed, the effect of energy dissipation in the thin lubricating film separating the sealing faces is pointed out, and the results of vaporization due to heating are illustrated. Also, hydrodynamic lubrication is reviewed, and an inherent tendency for the seal to operate with angular misalignment is pointed out. Recent work on hydrostatic effects is summarized and the conditions for seal instability are discussed. Four different modes of seal lubrication are postulated with the mode type being a strong function of speed and pressure.

Ludwig, L. P.↗
NASA NTRS1978

Twisted and warped disks as consequences of heavy halos

Observationally testable consequences of the hypothesis that galactic disks are confined less by their self-gravity than that of some hot stellar component are sought. Theoretical and observational studies are reviewed which suggest that elliptical galaxies are typically triaxial in form. It is argued that any hot stellar component is likely to be similarly spherical. The motion of a galactic disk about such a population is calculated. Within the plane the flow is to first order along similar concentric ellipses and without of the plane, provided that certain conditions on the background field are met, an oscillation may be excited which can cause isolated galaxies to become warped. The circular motion of matter in such disks will manifest itself in the misalignment of the apparent minor axis and the H I zero-velocity contour. Such an effect may be present in a number of recent H I surveys, although the data presently available do not allow definite conclusions. Alternative explanations of galactic warps are reviewed and their relation to the present proposal discussed.

Binney, J.↗
NASA NTRS1978

Precision attitude determination for multimission spacecraft

Attitude determination algorithms for a multimission spacecraft are derived and their performance analyzed. The attitude determination system is composed of a strapdown Inertial Reference Unit (IRU), two fixed head star trackers, and an onboard computer. IRU data is processed to maintain real-time knowledge of spacecraft attitude relative to an inertial reference frame. Star tracker data is processed using Kalman filtering techniques to estimate and correct the attitude determination errors and the gyro drift compensation errors. The results of a star availability analysis for stellar, solar and earth pointing missions are presented. Linear covariance analysis techniques are used to evaluate nominal attitude determination performance, the effects of sensor measurement accuracy variations, the effects of errors in knowledge of sensor measurement accuracy, and the effects of star tracker misalignment errors. Results of a nonlinear simulation analysis of attitude determination performance are also presented. These analyses show that precision attitude determination for stellar, solar and earth pointing missions is achieved.

Murrell, J. W.↗
NASA NTRS1978

Achievable flatness in a large microwave power antenna study

Achievable flatness for the microwave power transmission system antenna array was determined. Two configurations were analyzed in detail and evaluated as to their net potential misalignment. Manufacturing, joint slack, assembly, alignment and environmental aspects were considered. Approaches to each aspect were analyzed to minimize their contributions to distortions.

Source record↗
NASA NTRS1978

High speed cylindrical roller bearing analysis, SKF computer program CYBEAN. Volume 2: User's manual

The CYBEAN (Cylindrical Bearing Analysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. Input and output architectures containing guidelines for use and a sample execution are detailed.

Kleckner, R. J.↗
NASA NTRS1979

AXAF optical technology analysis

A grazing incidence telescope with six nested subsystems is investigated through the effects of misalignment and surface deformations on it's image quality. The axial rms-spot size serves as measure for the image quality. The surface deformations are simulated by ellipsoidal and sinusoidal deviation elements. Each type of defect is analyzed in the single two-element system. The full nested system is then analyzed in the presence of all possible defects on all twelve elements, whereby the magnitude of the defects is randomized within a given upper limit.

Korsch, D.↗
NASA NTRS1979

Conceptual design study of concentrator enhanced solar arrays for space applications Volume 2: Technical

Concentrator concepts which utilize Kapton mirror material were evaluated and selected for solar array use due to their zero mass. All concepts considered employed thin silicon solar cells. Design requirements for the concentrator were: the cell temperature was not to exceed 150 C; the concentrators were to produce illumination of the array within 15% of being perfectly uniform; the concentrators were to operate while misaligned as much as 5 degrees with the solar axis. Concentrator designs along with mirror structure and configurations are discussed and comparisons are made for optimal space applications.

Source record↗
NASA NTRS1966

Fluid pressure balanced seal

A seal which increases in effectiveness with increasing pressure is presented. The seal's functional capability throughout both static and dynamic operation makes it particularly useful for sealing ball valve ports. Other features of the seal include the ability to seal two opposed surfaces simultaneously, tolerance of small misalignments, tolerance of wide temperature ranges, ability to maintain positive sealing contact under conditions of internal or external pressurization, and ability to conform to slight irregularities in seal or surface contours.

Marsh, H. W.↗
NASA NTRS1979

Elastomer mounted rotors - An alternative for smoother running turbomachinery

This paper describes the design of elastomeric bearing supports for a rotor built to simulate the power turbine of an advanced gas turbine engine which traverses two bending critical speeds. The elastomer dampers were constructed so as to minimize rotor dynamic response at the critical speeds. Results are presented of unbalance response tests performed with two different elastomer materials. These results showed that the resonances on the elastomer-mounted rotor were well damped for both elastomer materials and showed linear response to the unbalance weights used for response testing. Additional tests were performed using solid steel supports at either end (hand-mounted), which resulted in drastically increased sensitivity and nonlinear response, and with steel supports in one end of the rotor and the elastomer at the other, which yielded results which were between the soft- and hard-mounted cases. It is concluded that elastomeric supports are a viable alternative to other methods of mounting flexible rotors, that damping was well in excess of predictions and that elastomeric supports are tolerant of small rotor misalignments.

Tecza, J. A.↗
NASA NTRS1979

Collapse and relaxation of rotating stellar systems

The evolution of initially spherical, uniform-density, and uniform-velocity-dispersion stellar systems is investigated by means of a three-dimensional N-body computer model. Some 100,000 simulation stars are used to follow the collapse and relaxation of the system for various amounts of angular momentum in solid-body rotation. For initially low values of the angular momentum satisfying the Ostriker-Pebbles stability criterion the systems quickly relax to an axisymmetric shape and resemble elliptical galaxies in appearance. The maximum flattening for these systems is equivalent only to an E2 system. For larger values of the initial angular momentum bars develop, and the systems undergo a much more drastic evolution. The apparent rotational and random velocities of the barred systems are very sensitive to the viewing direction. An additional complication is the frequent misalignment of the apparent major axis with the direction that reflects the maximum rotation.

Hohl, F.↗
NASA NTRS1979

Magnetometer bias determination and attitude determination for near-earth spacecraft

A simple linear-regression algorithm is used to determine simultaneously magnetometer biases, misalignments, and scale factor corrections, as well as the dependence of the measured magnetic field on magnetic control systems. This algorithm has been applied to data from the Seasat-1 and the Atmosphere Explorer Mission-1/Heat Capacity Mapping Mission (AEM-1/HCMM) spacecraft. Results show that complete inflight calibration as described here can improve significantly the accuracy of attitude solutions obtained from magnetometer measurements. This report discusses the difficulties involved in obtaining attitude information from three-axis magnetometers, briefly derives the calibration algorithm, and presents numerical results for the Seasat-1 and AEM-1/HCMM spacecraft.

Lerner, G. M.↗
NASA NTRS1980

Mechanical end joint for structural columns

Connector for tubular struts permits construction of lightweight frames without tools or assembly equipment. Two main components are node fitting and strut element. Components are aleaned approximately and pushed together. Design accommodates reasonable axial and rotational misalignment of nodes and struts. Also, individual columns can be inserted into receptacle and given slight push by operator, trigger pins release ratchet, allowing energy stored in springs to rotate screw into nut in receptacle.

Bush, H. G.↗