Search NASA⌕ Search

SEARCH · Search NASA

Results for “multifunctional material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Structural, Bulk Permittivity, and Magnetic Properties of Lead-Free Electronic Material: Ba{sub 1}Bi{sub 1}Cu{sub 1}Fe{sub 1}Ni{sub 1}Ti{sub 3}O{sub 12}

In this report, Ba{sub 1}Bi{sub 1}Cu{sub 1}Fe{sub 1}Ni{sub 1}Ti{sub 3}O{sub 12} (BBCFNTO termed further) ceramics were synthesized using a conventional ceramic processing route. The formation of multiple phases has been confirmed from by the XRD pattern at room temperature. The surface micrograph indicates the uniform distribution of grains with distinct grain boundary. The co-relation between the impedance and dielectric parameters was realized by using a phase sensitive meter over a good temperature and frequency range. The temperature- and frequency-dependent dielectric properties are linked to the conduction mechanism. The dielectric constant (K) and loss (tanδ) are increased sharply at high-temperature region, which is expected to be the onset of dipolar relaxation phenomena. The contribution of grain boundary (GBs) and grain (Gs) effects can be identified using the complex impedance spectroscopy. This synthesized material is investigated to model multifunctional devices.

36 MATERIALS SCIENCE↗

Multifunctional Superelastic Graphene Aerogels Derived from Ambient-Dried Graphene Oxide/Camphene Emulsions

Graphene oxide (GO) emulsions have been widely adopted to fabricate lightweight graphene aerogels (GAs). However, preparing high-performance GAs from conventional GO emulsions under ambient conditions seems rather challenging because of the structural collapse caused by strong capillary forces during drying. Here, we report a new, low-cost route to prepare high-performance, multifunctional GAs by the ambient drying of GO/camphene emulsions. Benefiting from the liquid-solid and solid-gas phase transitions of camphene, highly porous GO aerogels were obtained under ambient conditions. Moreover, the thermally annealed GO aerogels exhibited excellent mechanical properties, fire resistance, thermal insulation performance, and oil adsorption capability.

ambient drying↗

High Throughput Screening of 3D Printable Resins: Adjusting the Surface and Catalytic Properties of Multifunctional Architectures

Identification of 3D printable materials is crucial to expand the breadth of physical and chemical properties attainable by additive manufacturing. Stereolithography (SLA), a widespread 3D printing method based on resin photopolymerization, is ideally suited for exploring a large variety of monomers to produce functional three-dimensional solids of diverse properties. However, for most commercial SLA printers, screening monomers and resin compositions requires large volumes (~150 mL) in each printing cycle, making the process costly and inefficient. Herein, a high throughput block (HTB) adaptor was developed to screen arrays of monomers and resin compositions, consuming lower volumes (<2 mL) and less time per print (<1/16 based on a 4 × 4 matrix) than using the original hardware. By use of this approach, a library of materials with different surface hydrophobicities were 3D printed by including long chain acrylates in the resins. In addition, several metal salts were dissolved in an acrylic acid-based resin, 3D printed, and screened as benzyl alcohol oxidation catalysts. Cu(II)-based resins produced the most active structures. Combinations of Cu(II) and long chain acrylate monomers were then used to 3D print complex catalytic architectures with varying degrees of hydrophobicity. Linear relationships were observed between 3D printed surface area, surface hydrophobicity, and catalyst performance. For a high surface Schwarz P topology ca. 60% enhancement in the catalytic activity of Cu(II) was attained by replacing the parent resin with one containing hydrophobic isodecyl groups, indicating that the immediate environment of the catalytic site affected its performance. The HTB enables fast screening of resins for 3D printing multifunctional architectures with intrinsic catalytic activity, tunable surface properties, and minimal waste.

36 MATERIALS SCIENCE↗

Multiscale mechanical design of the lightweight, stiff, and damage-tolerant cuttlebone: A computational study

Cuttlebone, the endoskeleton of cuttlefish, offers an intriguing biological structural model for designing low-density cellular ceramics with high stiffness and damage tolerance. Cuttlebone is highly porous (porosity ~93%) and lightweight (density less than 20% of seawater), constructed mainly by brittle aragonite (95 wt%), but capable of sustaining hydrostatic water pressures over 20 atmospheres and exhibits energy absorption capability under compression comparable to many metallic foams (~4.4 kJ/kg). Here, in this work, we computationally investigate how such remarkable mechanical efficiency is enabled by the multiscale structure of cuttlebone. Using the common cuttlefish, Sepia Officinalis, as a model system, we first conducted high-resolution synchrotron micro-computed tomography (µ-CT) and quantified the cuttlebone's multiscale geometry, including the 3D asymmetric shape of individual walls, the wall assembly patterns, and the long-range structural gradient of walls across the entire cuttlebone (ca. 38 chambers). The acquired 3D structural information enables systematic finite-element simulations, which further reveal the multiscale mechanical design of cuttlebone: at the wall level, wall asymmetry provides optimized energy absorption while maintaining high structural stiffness; at the chamber level, variation of walls (number, pattern, and waviness amplitude) contributes to progressive damage; at the entire skeletal level, the gradient of chamber heights tailors the local mechanical anisotropy of the cuttlebone for reduced stress concentration. Our results provide integrated insights into understanding the cuttlebone's multiscale mechanical design and provide useful knowledge for the designs of lightweight cellular ceramics.

36 MATERIALS SCIENCE↗

Photoluminescence and electrical characterization of unfilled tetragonal tungsten bronze Ba{sub 4}La{sub 1−x}Eu{sub x}TiNb{sub 9}O{sub 30}

Graphical abstract: PL spectra of the unfilled TTB structure BLTN: Eu{sup 3+}x samples (x = 0.00, 0.25, 0.50, 0.75, and 1.00) excited by 399 nm. The inset is a schematic diagram of the unfilled TTB structure. - Highlights: • Unfilled TTB structure BLTN: Eu{sup 3+}x ceramics have been synthesized. • Photoluminescenct properties of the BLTN: Eu{sup 3+}x ceramics have been first reported. • Bright red emission excited by NUV light has been observed at room temperature. • Obvious variations of dielectric characteristics have been confirmed. • Relaxor-like ferroelectric phase transitions have been detected. - Abstract: Unfilled tetragonal tungsten bronze (TTB) structure Ba{sub 4}LaTiNb{sub 9}O{sub 30} doped by Eu{sup 3+} (BLTN: Eu{sup 3+}x) with different x have been prepared, and their structural, photoluminescence, dielectric, and ferroelectric properties are carefully investigated in this work. Bright red emission, originating from {sup 5}D{sub 0} → {sup 7}F{sub 1} and {sup 5}D{sub 0} → {sup 7}F{sub 2} transitions of Eu{sup 3+} ions, has been observed by naked eyes at room temperature under near ultraviolet (NUV) light excitation. Optimized emission intensity is obtained when x = 1.00 for present unfilled TTB-type BLTN: Eu{sup 3+}x samples. Furthermore, with increasing x, the dielectric and ferroelectric characteristics of the unfilled TTB-type BLTN: Eu{sup 3+}x samples also display remarkable variation. When x ≥ 0.50 relaxor-like ferroelectric phase transitions are detected above room temperature, it is believed that unfilled TTB-type BLTN: Eu{sup 3+}x = 1.00 involving bright photoluminescence and enhanced ferroelectric properties may act as a potentially multifunctional optical-electro material.

36 MATERIALS SCIENCE↗

Light–ferroelectric interaction in two-dimensional lead iodide perovskites

The unique physical properties of two-dimensional (2D) metal halide perovskites (MHPs) such as nonlinear optics, anisotropic charge transport, and ferroelectricity have made these materials promising candidates for multifunctional applications. Recently, fluorine derivatives such as 4,4-difluoropiperidinium lead iodide perovskite or (4,4-DFPD, C 5 H 10 F 2 N) 2 PbI 4 have shown strong ferroelectricity as compared to other 2D MHPs. Although it was previously addressed that the ferroelectricity in MHPs can be affected by illumination, the underlying physical mechanisms of light–ferroelectricity interaction in 2D MHPs are still lacking. Here, we explore the electromechanical responses in 4,4-(DFPD) 2 PbI 4 thin films using advanced scanning probe microscopy techniques revealing ferroelectric domain structures. In this work, hysteretic ferroelectric loops measured by contact-Kelvin probe force microscopy are dependent on domain structures under dark conditions, while ferroelectricity weakens under illumination. The X-ray diffraction patterns exhibit significant changes in preferential orientation of individual lattice planes under illumination. Particularly, the reduced intensity of the (1 1 1) lattice plane under illumination leads to transitioning from a ferroelectric to a paraelectric phase. The instability of positive ions, especially molecular organic cations, is observed under illumination by time-of-flight secondary ion mass spectrometry. The combination of crystallographic orientation and chemical changes under illumination clearly contributes to the origin of light–ferroelectricity interaction in 2D (4,4-DFPD, C 5 H 10 F 2 N) 2 PbI 4 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Room temperature dual ferroic behaviour of ball mill synthesized NdFeO{sub 3} orthoferrite

Phase pure NdFeO{sub 3} has been achieved using high energy ball milling of oxide precursors with subsequent sintering. It is established that structural arrangement of NdFeO{sub 3} regulates the multifunctional feature of the material. Rietveld refinement of the room temperature X-ray diffraction pattern shows that the Fe-O-Fe bond angle significantly favors the super exchange interaction, which is predominantly antiferromagnetic in nature. Magnetization measurement illustrates antiferromagnetic behaviour with a weak ferromagnetic component caused by the canted nature of the Fe{sup 3+} spins at room temperature. Absorption bands in the visible ambit, apparent from the UV-Vis diffuse reflectance studies, is found due to the crystal ligand field of octahedral oxygen environment of Fe{sup 3+} ions. The direct band gap is estimated to be 2.39 eV from the diffuse reflectance spectrum. The lossy natured ferroelectric loop having a maximum polarization of 0.23 μC/cm{sup 2} at room temperature is found to be driven by the non-collinear magnetic structure with reverse Dzyaloshinskii–Moriya effect. Magnetic field has influence on the dielectric constant as evident from the impedance spectroscopy, indicating the strong coupling between ferroelectric and the magnetic structure of NdFeO{sub 3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fabrication and characterization of 3D printing induced orthotropic functional ceramics

The orthotropic functional properties of additively manufactured ceramics due to the fabrication process was characterized in this study. Spherical, environmentally benign barium titanate (BaTiO 3 ) powders were fabricated using binder jetting 3D printing. Dielectric and piezoelectric properties of these ceramics were characterized as a function of the printing orientation. The dielectric constant of the samples tested normal to the printing layers was observed to be 20% higher than those tested in the parallel fashion. Similarly, the piezoelectric response was found to be over 35% in the normal orientation. With these results, it was shown that the electroding orientation has a direct influence on the functional properties of additively manufactured ceramics. Overall, with less than 37% of the theoretical density, the average piezoelectric coefficient for the perpendicularly tested ceramics was found to be 152.7 pC N -1 , which is 80% of the theoretical value. Finally, the high piezoelectric response obtained with such low densities can lead to the development of more mass efficient, and cost-effective sensing and energy harvesting devices, as well as structures that can be tuned to respond based on the direction of the loads applied.

36 MATERIALS SCIENCE↗

Multifunctional, High-Temperature Nanocomposites

In experiments conducted as part of a continuing effort to incorporate multifunctionality into advanced composite materials, blends of multi-walled carbon nanotubes and a resin denoted gPETI-330 h (wherein gPETI h is an abbreviation for gphenylethynyl-terminated imide h) were prepared, characterized, and fabricated into moldings. PETI-330 was selected as the matrix resin in these experiments because of its low melt viscosity (<10 poise at a temperature of 280 C), excellent melt stability (lifetime >2 hours at 280 C), and high temperature performance (>1,000 hours at 288 C). The multi-walled carbon nanotubes (MWCNTs), obtained from the University of Kentucky, were selected because of their electrical and thermal conductivity and their small diameters. The purpose of these experiments was to determine the combination of thermal, electrical, and mechanical properties achievable while still maintaining melt processability. The PETI-330/MWCNT mixtures were prepared at concentrations ranging from 3 to 25 weight-percent of MWCNTs by dry mixing of the constituents in a ball mill using zirconia beads. The resulting powders were characterized for degree of mixing and thermal and rheological properties. The neat resin was found to have melt viscosity between 5 and 10 poise. At 280 C and a fixed strain rate, the viscosity was found to increase with time. At this temperature, the phenylethynyl groups do not readily react and so no significant curing of the resin occurred. For MWCNT-filled samples, melt viscosity was reasonably steady at 280 C and was greater in samples containing greater proportions of MWCNTs. The melt viscosity for 20 weightpercent of MWCNTs was found to be .28,000 poise, which is lower than the initial estimated allowable maximum value of 60,000 poise for injection molding. Hence, MWCNT loadings of as much as 20 percent were deemed to be suitable compositions for scale-up. High-resolution scanning electron microscopy (HRSEM) showed the MWCNTs to be well dispersed in the polymer matrices, while high-resolution transmission electron microscopy shows splits in the walls of the MWCNTs but no catastrophic breakage of tubes. To further assess processing characteristics prior to scale-up, samples containing 10, 15, and 20 weight-percent of MWCNTs were processed through a laboratory melting extruder. HRSEM of the extruded fibers shows significant alignment of MWCNTs in the flow direction (see figure). For the samples containing 20 weight-percent of MWCNTs, difficulties were encountered during feeding, and the temperature of a rotor in the extruder rose to 245 C because of buildup of frictional heat; this indicates that materials of this type having MWCNT concentrations .20 weight- percent may not be melt-processable. On the basis of the results from the foregoing characterizations, samples containing 10, 15, and 20 weight-percent of MWCNTs were scaled up to masses of .300 g and used to make specimens having dimensions of 10.2 by 15.2 by 0.32 cm. These specimens were molded by (1) injecting the mixtures, at temperatures between 260 and 280 C, into a tool made of the low-thermal-expansion alloy InvarR and then (2) curing for 1 hour at 371 C. The tool was designed to impart shear during the injection process in an attempt to achieve some alignment of the MWCNTs in the flow direction.

Connell, John W.↗

Microstructure Quantification and Random Forest Regression Models for Li4Ti5O12–Ni Property Prediction

All-solid-state structural lithium-ion batteries are sought to enable all-electric propulsion in next generation aerospace concepts through improved safety and systems level weight savings. In this work, the influence of processing conditions on microstructural evolution was evaluated for anode composites of strain-free Li4Ti5O12 and metallic nickel current collector. Beyond size distributions, this study explored methods of quantifying microstructural features that describe changes in the spatial distribution and coalescence of nickel particles as a function of sample composition and sintering conditions. Processing-microstructure-property relationships were described by microstructure quantifiers including nickel particle count per area, nearest neighbor distance distribution, and edge-to-edge distance distribution. Machine learning methods were applied to compare the relative influence of processing conditions and microstructural features on electrical conductivity and mechanical strength to optimize for simultaneous energy storage and load bearing performance. Insights gained from this work inform future evaluation of alternative energy storage materials and microstructures for multifunctional performance, and generation of microstructural descriptors strengthens modeling across length scales.

anode↗

One-step synthesis and stabilization of gold nanoparticles and multilayer film assembly

Au nanoparticles (NPs) were synthesized in the one-pot procedure in water at room temperature with the wheel-shaped V{sup V}-V{sup IV} mixed-valence tungstovanadate [P{sub 8}W{sub 48}O{sub 184{l_brace}}V{sub 4}{sup V}V{sub 2}{sup IV}O{sub 12}(H{sub 2}O){sub 2{r_brace}2}]{sup 32-} (V12) acting as both reducing and stabilizing agents. The V12 stabilized Au NPs (Au-V12 NPs) were characterized by SEM, TEM, DLS, UV-vis spectroscopy, XPS, and XRD analyses and the negatively charged surface of the Au-V12 NPs was proved by the zeta potential analysis. Based on the layer-by-layer assembly (LbL), the Au-V12 NPs-containing multilayer films have been fabricated on ITO-coated glass slide and quartz substrates with poly(ethyleneimine) (PEI). The regular growth of the multilayer films was monitored by UV-vis spectroscopy and cyclic voltammetry, the composition was characterized by XPS. The Au-V12 NPs based composite films showed electrocatalytic activities towards the reduction of dioxygen and the oxidation of methanol. This approach is expected to open the way towards procedures aimed at the one-step fabrication of Au NPs and polyoxometalates (POMs) into the multilayer films. -- Graphical abstract: The wheel-shaped V{sup V}-V{sup IV} mixed-valence tungstovanadate [P{sub 8}W{sub 48}O{sub 184{l_brace}}V{sub 4}{sup V}V{sub 2}{sup IV}O{sub 12}(H{sub 2}O){sub 2{r_brace}2}]{sup 32-} (V12) stabilized Au nanoparticles (Au-V12 NPs) have been synthesized and characterized. The multilayer films containing Au-V12 NPs were fabricated and their electrocatalytic properties were studied. Display Omitted Research highlights: {yields} Au core-V12 shell nanostructures, Au-V12 NPs, were synthesized and characterized. {yields} The negatively charged Au NPs were fabricated and catalytic properties were studied. {yields} This study opens the way to the fabrication of multifunctional thin-film materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Additive Manufacturing of Multifunctional Components Using High Density Carbon Nanotube Yarn Filaments

Additive manufacturing allows for design freedom and part complexity not currently attainable using traditional manufacturing technologies. Fused Filament Fabrication (FFF), for example, can yield novel component geometries and functionalities because the method provides a high level of control over material placement and processing conditions. This is achievable by extrusion of a preprocessed filament feedstock material along a predetermined path. However if fabrication of a multifunctional part relies only on conventional filament materials, it will require a different material for each unique functionality printed into the part. Carbon nanotubes (CNTs) are an attractive material for many applications due to their high specific strength as well as good electrical and thermal conductivity. The presence of this set of properties in a single material presents an opportunity to use one material to achieve multifunctionality in an additively manufactured part. This paper describes a recently developed method for processing continuous CNT yarn filaments into three-dimensional articles, and summarizes the mechanical, electrical, and sensing performance of the components fabricated in this way.

Gardner, John M.↗

Compressed glassy carbon: An ultrastrong and elastic interpenetrating graphene network

Carbon’s unique ability to have both sp 2 and sp 3 bonding states gives rise to a range of physical attributes, including excellent mechanical and electrical properties. We show that a series of lightweight, ultrastrong, hard, elastic, and conductive carbons are recovered after compressing sp 2 -hybridized glassy carbon at various temperatures. Compression induces the local buckling of graphene sheets through sp 3 nodes to form interpenetrating graphene networks with long-range disorder and short-range order on the nanometer scale. The compressed glassy carbons have extraordinary specific compressive strengths—more than two times that of commonly used ceramics—and simultaneously exhibit robust elastic recovery in response to local deformations. Finally, this type of carbon is an optimal ultralight, ultrastrong material for a wide range of multifunctional applications, and the synthesis methodology demonstrates potential to access entirely new metastable materials with exceptional properties.

36 MATERIALS SCIENCE↗

Multifunctional Epidermal Electronics Printed Directly onto the Skin

Materials and designs are presented for electronics and sensors that can be conformally and robustly integrated onto the surface of the skin. A multifunctional device of this type can record various physiological signals relevant to health and wellness. Furthermore, this class of technology offers capabilities in biocompatible, non-invasive measurement that lie beyond those available with conventional, point-contact electrode interfaces to the skin.

36 MATERIALS SCIENCE↗

Locally Engineering and Interrogating the Photoelectrochemical Behavior of Defects in Transition Metal Dichalcogenides

Transition metal dichalcogenides (TMDs) are attractive materials for a variety of applications in solar energy conversion and electrocatalysis, due to their favorable optical and electrical properties and their unique two-dimensional structures which facilitate the fabrication of wide-area, ultrathin layers. Unfortunately, the basal planes which make up the majority of these materials are relatively inert, and thus a great deal of effort has been directed to engineering favorable, catalytically active defects into these materials. In this paper, we demonstrate how probe-based electrochemical techniques can be employed as multifunctional tools for locally modifying TMD materials and probing the electrochemical behavior of the resulting defects. Scanning Electrochemical Cell Microscopy (SECCM) was employed to locally anodize exfoliated p-type WSe 2 nanosheets, creating hole-like defects within individual basal planes in a highly controllable fashion. Photoelectrochemical SECCM imaging was then employed to characterize the chemical behavior of these engineered defects, revealing significantly enhanced activity toward the Hydrogen Evolution Reaction (HER). Atomic force microscopy studies are presented which suggest these enhancements result from an increased density of monolayer-high step features within the anodized defects. Analysis of the SECCM data in the context of finite element simulations revealed that these enhancements increased with increasing anodization time, with local kinetic rates over 2 orders of magnitude higher than unaltered basal planes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced multifunctional paint for detection of radiation

An enhanced multifunctional paint apparatus, systems, and methods for detecting radiation on a surface include providing scintillation particles; providing an enhance neutron absorptive material; providing a binder; combining the scintillation particles, the enhance neutron absorptive material, and the binder creating a multifunctional paint; applying the multifunctional paint to the surface; and monitoring the surface for detecting radiation.

36 MATERIALS SCIENCE↗

Modification of Hexagonal Boron Nitride with Metal Oxides

The development of multifunctional hexagonal boron nitride (hBN) materials aims to capitalize on the intrinsic properties of hBN which include being electrically insulating, thermally conductive, and chemically and thermally stable at high temperatures. The creation of novel composite materials that include these properties is required to address our current aerospace and space engineering challenges. Researchers at NASA Glenn have done significant prior work which has produced processes to intercalate, exfoliate, coat, and functionalize various hBN materials. This presentation covers our recent progress towards the integration of titanium oxides into hBN utilizing our previous methods along with optimizing and producing new methods to create novel functional hBN nanomaterials.

boron nitride↗

Complex Materials for Molecular Spintronics Applications: Cobalt Bis(dioxolene) Valence Tautomers, from Molecules to Polymers

Using first principles calculations, we predict a complex multifunctional behavior in cobalt bis(dioxolene) valence tautomeric compounds. Molecular spin-state switching is shown to dramatically alter electronic properties and corresponding transport properties. This spin state dependence has been demonstrated for technologically relevant coordination polymers of valence tautomers as well as for novel conjugated polymers with valence tautomeric functionalization. As a result, these materials are proposed as promising candidates for spintronic devices that can couple magnetic bistability with novel electrical and spin conduction properties. Our findings pave the way to the fundamental understanding and future design of active multifunctional organic materials for spintronics applications.

Chemistry↗