Search NASA⌕ Search

SEARCH · Search NASA

Results for “nylons”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

319 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Predicting the Penetration of a Shielded TPS Tile

All spacecraft are subject to the possibility of high-speed particle impacts during their mission life. In low earth orbit, those impacts could be the result of collisions with pieces of orbital debris or with meteorites. Beyond LEO, and especially beyond GEO, those impacts will likely be caused by meteorites. Such high-speed impacts on spacecraft surfaces create debris clouds that travel towards and eventually impact other downstream spacecraft components. In addition to the impulsive load that such debris clouds would impart to the spacecraft elements with which they subsequently collide, the largest fragment in these debris clouds poses a significant threat on its own to those spacecraft elements. In order to be able to assess the severity of the threat posed by such a fragment, it is important to be able to predict the extent of damage sustained by the impacted spacecraft element. In this paper, we present a new process for determining the penetration depth in a shielded TPS tile system. The requirements for the process were that it be applicable across a full spectrum of impact low velocities (i.e. from ~ 7 km/s to above 50 km/s), that it be applicable over a wide range of projectile materials densities (i.e. ranging from water to steel, for example), and that it be applicable over a wide range of trajectory obliquities (i.e. not just normal impacts). Furthermore, the process developed should be sufficiently flexible so that it can be used for shield design parameter and / or system configuration trade studies (i.e. be written in terms of as many shield and TPS tile system parameters as possible). Following the initial impact of the projectile on the outer wall of the dual-wall shield, a debris cloud (i.e. the primary debris cloud) is created that travels towards and impacts the inner wall of the shield. Within this debris cloud is a combination of solid, liquid, and vaporized material, depending on the impact velocity and the impedance mismatch of the projectile and outer wall materials. The impact of this debris cloud on the inner wall creates another debris cloud (i.e. the secondary debris cloud) that then travels towards and impacts the TPS tile. Within the particulate distribution of the material in each of these debris clouds is a so-called largest fragment. The process used to calculate the penetration depth in a shielded TPS tile system developed herein consists of the following three steps: 1. Does the initial projectile perforate the outer wall of the shield? If NO, the TPS tile remains undamaged. If YES, calculate the size and speed of the largest fragment exiting the outer wall of the shield and traveling towards the shield’s inner wall. 2. Does the largest fragment in the debris cloud exiting the outer wall of the shield perforate the inner wall of the shield? If NO, the TPS tile again remains undamaged. If YES, calculate the size and speed of the largest fragment exiting the rear of the shield inner wall. 3. Calculate the penetration depth of the largest fragment in the debris cloud exiting the inner wall into the TPS. Perforation of the inner and outer shield walls is predicted using the Cour-Palais penetration depth equation and an associated failure criterion [1]. The largest debris cloud fragment diameters and associated velocities are calculated using regression equations developed from a mix of hydrocode and experimental diameter and velocity information [2]. Finally, TPS penetration depths are calculated using an empirical penetration depth predictor equation based on high-speed impact test data and are calibrated using a limited number of hydrocode penetration depth predictions for water, nylon, aluminum, Dunite, and steel projectiles The predictions of the penetration depth calculation process are compared against the predictions of more than 60 SPHC hydrocode runs. These comparisons show that the process used to calculate TPS tile penetration depths usually yields values that are within 1 mm of the predictions of hydrocode simulations. If a maximum allowable TPS penetration depth is known, the process developed herein can now be used to develop a failure limit equation that would predict whether or not an impacting particle would penetrate deeply enough into the TPS to result in a “failed” or “not failed” end state. References [1] E.L. Christiansen, “Design and performance equations for advanced meteoroid and debris shields”, International Journal of Impact Engineering, Vol. 14, 1993, pp. 145-156. [2] W.P. Schonberg, “Predicting the size of the largest particle fragment in a debris cloud created by an orbital debris impact and its associated velocity”, 2021 Applied Space Environments Conference, NASA Jet Propulsion Laboratory, Pasadena, California, November, 2021.

Meteroid↗
NASA NTRSDate not supplied

Prediction and Enhancement of Thermal Protection Systems from Meteoroid Damage using a Smooth Particle Hydrodynamic Code

Interplanetary spacecraft are exposed to meteoroid fluxes that range in speeds from 10 to 72 km/sec, far above the capability of today’s test facilities to provide predictions for the likelihood of spacecraft critical penetration. Of special interest are sample return missions, which (though protected by shielding) must often survive years of exposure to the meteoroid environment in order to re-enter Earth’s atmosphere with their scientific cargo. This paper describes the simulation of meteoric material damage to thermal protection systems (TPS) housed beneath protective “garage” (shielding) enclosures using the Smooth Particle Hydrodynamics Code (SPHC) operated by the Institute for Defense Analyses and Stellingwerf Consulting in support of ongoing NASA tasks. The study outlined in this paper considered the impact effect of both meteoric materials such as iron, ice, and chondrites (dunnite), and non-meteoric materials such as aluminum and nylon against both external shielding materials (single and dual aluminum bumpers) and Heat shield for Extreme Entry Environments Technology (HEEET) TPS materials, used alone and in conjunction with shielding. A general predictive damage equation to HEEET TPS is developed from these SPHC simulations for velocities up to 70 km/sec.

Hypervelocity Impact, hydrocode, meteoroid and orb↗
NASA NTRSDate not supplied

Modeling Ring-Opening Polymerization with Machine-Learned Committors

Many important industrial and biological processes depend on ring-opening polymerization (ROP), including large-scale production polymers, such as nylon 6, and a variety of biodegradable polymers and high-performance resins. Large-scale simulations (>200K atoms) of ROP were performed using a deep neural network-based method that captured the effect of the local chemical environment of the reactive sites using training data from quantum chemical methods. The utility of this method was demonstrated by modeling the cationic ROP of bis-benzoxazine, a promising resin for use in advanced high-temperature application composites (>200°C). Density functional theory calculations were used to map out the various ring opening and polymerization reaction paths that occur during the thermal processing of bis-benzoxazine. The probabilities of these reactions, as a function of local atomic configurations, were used to construct committor functions using a neural network approach. The learned committor functions were then used to determine when a particular reaction occurred within the REACTER framework for reactive molecular dynamics simulations. The experimentally observed exotherm that occurs during bis-benzoxazine ROP was captured in an effective manner in the simulations by imposing a local heating of the system that corresponds to the enthalpy of reaction for each reaction. The dependence of the final polymer morphology on the ROP reaction temperature was analyzed at the molecular scale. The results presented in this work indicate that machine-learned committor functions are a promising approach for incorporating high-fidelity reactivity criteria that capture the effect of local chemical environments into large-scale polymerization simulations.

machine learning, polymer simulations, molecular d↗
NASA NTRS2023

Combined Experimental and Modeling Study of the Interactions of Acid Gas with Common Spacecraft Surfaces for Fire Safety Applications

A fire in a spacecraft poses detrimental consequences and risks mission success in addition to crew safety. This is compounded during long-duration missions when the crew has limited options to recover from a fire. A common spacecraft fire concern is the smoldering of wire insulation, typically made from Polyvinyl chloride (PVC) or Polytetrafluoroethylene (PTFE). This creates acid gases such as Hydrogen Chloride (HCl), Hydrogen Fluoride (HF) and Hydrogen Cyanide (HCN). These poisonous gases are hazardous to the crew. They also interact with common surfaces within the spacecraft more than dominant combustion products such as CO2 and H2O. This makes them more difficult to track for potential fire detection techniques, or for postfire clean-up. It is imperative to be able to understand and predict the fate of these poisonous species in a microgravity environment in order to design a safe vehicle. HCl interacts with a number of materials inside a spacecraft. Primary among these materials is aluminum, which is abundantly used due to its strong and light weight nature. Aluminum has a natural oxide layer that protects it from corrosion but is typically treated to enhance this oxide layer. Among these treatments is a chromate conversion coating (CCC), which provides a thin enough protective oxide layer to still conduct electricity, and a traditional anodized material that has a thicker oxide layer that does not conduct electricity. Nomex is another common material found inside a spacecraft. It is a flame-resistant woven polymer that is related to nylon. This commercially available material is used for cargo storage bags and as a fire barrier. Physics-based models were developed to predict the uptake of HCl by these materials. The ultimate objective of these models is to predict the fate of HCl within the spacecraft so that sensors can be placed in meaningful locations in future missions based on the model predictions. To support these modeling efforts, experiments were performed in a cast acrylic test cell that measured the difference between the inlet and outlet concentration of HCl after inserting a sample rod of the test material. Different uptake capacities were realized for each type of sample tested. A computational fluid dynamics model (CFD) model of the reactor was then constructed that used a one-step global reaction rate with calibratable reaction (or kinetic) constants. These constants were calibrated to match the HCl uptake on the CCC aluminum samples, and the same kinetic constants were then tested for the stock and anodized aluminum samples. Model predictions matched the experimental data for the stock aluminum, and to a much lesser extent, the anodized aluminum. The model was additionally validated at different flow rates, sample surface areas, and inlet concentrations, and showed good agreement for all stock and CCC samples. The model did not accurately predict the HCl uptake in the anodized samples compared to the other two types of aluminum. Adjusting the kinetic constants and transport properties did little to improve the prediction. X-Ray Photoelectron Spectroscopy (XPS) was used to determine that the oxide layer thickness of anodized aluminum is approximately 5,000 nm, compared to 250 nm for CCC and 50 nm for stock. XPS also revealed presence of chlorine further down in the aluminum oxide layer in anodized samples than CCC and stock samples after the samples were saturated with HCl, indicating that accounting for diffusion of HCl into the oxide layer is important for accurate prediction of HCl uptake onto anodized aluminum. Consequently, a multi-scale model was developed and tested. First, a single pore inside the anodized aluminum oxide layer was modeled and is referred to as the pore-scale model. In this model, HCl diffused through the pore and reacted with the aluminum oxide pore wall to create aluminum chloride. The sample was then saturated when the mass transfer resistance through the growing aluminum chloride layer became too large for the HCl to reach the aluminum oxide wall and continue the reaction. This pore-scale model was coupled to the reactor-scale model using a concentration-dependent diffusion coefficient, resulting in much more accurate predictions (approximately half the sum square error of the aforementioned reactor-scale model that produced good agreement for stock and CCC) for a variety of operating conditions. The amount of water vapor or relative humidity (RH) in the flow during a reactor experiment was determined to influence HCl uptake. Experiments were performed to understand the interaction of gaseous HCl with aluminum surfaces in the presence of water vapor. The results show that increasing levels of RH increased the capacity of aluminum to adsorb HCl but decreased the capacity of Nomex to uptake HCl. A series of tests were performed on individual aluminum samples after they had been saturated with a fixed concentration of HCl in dry air conditions with the goal of determining how their HCl uptake capacity changes after various treatments with water relative to the original saturation tests. HCl-saturated aluminum samples subjected to a second dry air flow at the same HCl concentration as the original test had an uptake of 23.5% of the original sample with no treatment in between. Saturated aluminum samples subjected to an air flow with a RH of 90% in between tests had an uptake of 35.6% of the original. Saturated aluminum samples submerged in distilled water for 12 hours in between tests had an uptake of 82.2% of the original sample. Previously saturated aluminum tested with HCl and a 50% RH air flow resulted in similar uptake characteristics in multiple repeated tests. The experiments show the profound effect water vapor has on HCl uptake onto aluminum surfaces. In the samples subjected to water vapor or liquid water, capillary condensation and capillary diffusion alters the transport of HCl significantly. A model was proposed that developed a relationship between RH and the coefficient of HCl diffusion in aluminum chloride. This produced an “S-shaped” curve with diffusion coefficient as a function of RH, with 45% RH represented as the point where the diffusion coefficient is halfway between no water saturation and 100% water saturation in the aluminum chloride product layer. No difference in uptake characteristics for the experiment or model were realized between 50% and 62% RH. The results from the large-scale microgravity experiment, Saffire, are discussed as they pertain to the fate of HCl throughout a spacecraft. HCl was released, both as a standalone event, and in concurrence with the burning of a structured cloth. These events only produced a small response in the far field HCl sensor, while a PMMA burn that did not produce HCl had a significantly greater response. A ground-based large-scale facility was constructed to flow acid gas at the scale and configuration realized in the Saffire experiments. A CFD model of this duct was constructed to test kinetic parameters developed in this work at a larger scale and different geometric configuration and to predict the results of the large-scale facility. The models developed in this work were used to interpret the results of the microgravity tests and lead the discussion on what further experiments and models are needed in order to predict the fate of acid gas in a spacecraft environment. To summarize, the major contributions of this work are as follows: the capacity to uptake HCl, with and without the presence of water vapor, was measured for a variety of real spacecraft surfaces. Several different models (single reactor-scale, multiscale, spacecraft-scale) were developed and with the aid of modeling, the rate of uptake for those surfaces was also predicted and validated. The kinetic parameters determined from the small-scale reactor experiments and models were used to predict large-scale and microgravity tests. Conclusions from this research will be used in the design of spacecraft vehicles and large-scale microgravity fire safety experiments. The models built by this work will aid designers in sensor placement and could be used to predict acid gas transport from fires in partial gravity, as would be seen in Lunar and Martian habitats.

fire safety↗
NASA NTRS2023

NASA X-HAB Water Delivery System

As part of the eXploration Systems and Habitation (X-HAB) Academic Innovation Challenge program of National Aeronautics and Space Administration (NASA), The Ohio State University was selected to improve the performance of NASA’s existing Vegetable Production System (VEGGIE), which is a deployable plant growth unit for International Space Station (ISS). During the academic year 2015-2016, The Ohio State University student team developed a passive water delivery system using capillary water transport principle (Jenson et al. 2016). The major design improvement made was directly connecting the water reservoir to the plant-rooting pillows using a single-interface capillary cord design. Harvestable plants were successfully grown from seeds using the single interface system. In addition, Nomex®, a fabric material composed of short nylon based fibers, was identified as the material for wicks. Finally, the water reservoir was modeled as a propellant management device (PMD) to ensure consistent and long term watering of the VEGGIE system. The PMDs are made of materials that utilize surface tension and adhesive forces to improve stability and fluid delivery. The team recommended using a sponge PMD in order to mitigate bubble obstruction, decrease system weight, and ensure reliable water delivery to the capillary interface.

Peter Ling↗
NASA NTRSDate not supplied

Understanding the Response of Common Spacecraft Shields to Hypervelocity Impacts of Meteorite and Other Terrestrial Analog Materials

Micrometeoroid and orbital debris (MMOD) populations can vary significantly in composition, density, and homogeneity. Hypervelocity testing campaigns intended to design and optimize MMOD shields for spacecraft are recognizing the need to investigate shield response from different types of impactors that span the range of densities observed in the MMOD population, such as nylon, Al, Al 2 O 3 , steel, and Cu. These tests, however, still pre-dominantly employ spherical and homogenous projectiles. Adding any compositional or mineralogical complexity to the impactor, such as what would be expected from a polymineralic micrometeoroid, for ex-ample, will be concomitant with a more complex shockwave structure in the projectile after it impacts the outer surface of any type of MMOD shield. The magnitude of these complexities will depend on how varied the mineralogy of the projectile is, but in the case of a metal-bearing chondrite, the disparate shock impendence between adjacent metal and silicate grains will potentially create localized areas of shock focusing (local increase in nominal shock pressure), or shock shadowing (local decrease in nominal shock pressure). The response of a MMOD shield is generally predicted using a ballistic limit equation – a semiempirical curve, derived from hypervelocity testing data, that denotes a particle diameter (for a given set of impact conditions such as projectile density and impact angle) when a shield will fail as a function of impact speed. These curves exhibit inflection points as a function of impact speed that represent when the projectile experiences sufficient pressure to fragment, melt, or vaporize. The introduction of shock focusing and shadowing in a heterogenous projectile will add uncertainty to the predicted pressures needed to go through each transition, leading to increased uncertainty in the expected performance of the MMOD shield. Therefore, it is necessary to explore the performance of MMOD shields in hypervelocity tests against more complex, natural projectile materials. To this end we have conducted a comparative test series to begin investigating the impact damage caused by meteoritic and terrestrial-analog projectiles, to that of spherical Al projectiles of similar mass.

Impact testing↗
NASA NTRS2024

3D Printed Materials Characterization for Rapid Prototyping and Plant Growth

Through KSC IRTD funding in 2022, this project brought a list of 18, 3D printed filaments into formal characterization testing to provide a reference for their behaviors under relevant applications. The project format set up a series of tests to expose 3D printed specimens. A total of 1,989 individual 3D printed test specimens were sent across KSC to be scrutinized by three laboratories to fulfill a multidisciplinary assessment of each material TRL. Testing started with 18 materials. Initially, seed germination assays in the PPA, sample materials were enclosed in petri dishes with lettuce seeds on damp germination paper. No significant impacts on lettuce seed germination were observed in this testing. Next, sample coupons were printed and sent for materials testing to the KSC Analysis/Mechanical and Environmental Testing Laboratory, where they were subjected to 14- and 30-day soak periods in solutions used to provide nutrients to plants or to sanitize hardware before and after use. Following a long soak typical of a 30-day plant growout in Hoagland’s solution, 14 materials gained more than 10% of their own mass. This indicated an increased potential for leaching or providing conditions that are not food safe. Materials that exceeded 15% absorption by mass were eliminated from further testing. Based off this result, the team continued with a core list of nine filaments to fulfill Tensile, Flexural, Biofilm formation, and plant growth testing. Those materials were PLA (Raise3D), ABS (Raise3D), PETG (PolyethyleneTerephthalate Glycol) (Raise3D), ASA (Acrylonitrile Styrene Acrylate) (Raise3D), PC (Polycarbonate) (Raise3D), TPU (Thermoplastic polyurethane)-95 (Raise3D), PLA Copper (Gizmodorks), PP (Polypropylene) (Braskem), and HIPS (High Impact Polystyrene) (Gizmodorks). Testing also quantified the spectral impact of using different color 3D printed surfaces in a growth chamber. The material used for spectral testing was PLA. Printing employed a standard surface texture representative of all materials. It was shown through Tensile Testing (ASTM D638-22) that the breaking force of a 3D printed part greatly varied depending on layer orientation. This is common through all materials, and demonstrates that the strength of a 3D printed component can be maximized by layering the material normal to the primary force on the part. Four-point flexural testing (ASTM D790) provided quantities of interest, Flexural modulus, Flexural strength, Flexural stress, and strain at break within a 5% strain limit from each of nine materials. Biofilm formation testing was conducted in the Molecular and Microbiological Laboratory. Testing completed on specimens from each material showed equal formation on the surface. Additional plant growth testing was conducted in the PPA beyond the initial germination testing. The final assessment documents that three materials (PLA, ABS, and PC) have reached TRL 6 through extensive testing, and ultimate end-to-end applied use in experimental or testing conditions (flight and ground). TRL 5 materials (ASA, TPU-95, PLA Copper, PP, PETG, and HIPS) have all been successfully applied in Research and Development for crop growth applications and are ready to be applied in formal testing. TRL 4 materials Nylon910, PLA Carbon Fiber, PPA CF, PPA Glass Fiber (GF), NinjaFlex, and P-filament 721 are materials that were able to be printed and tested, but have yet to show data meeting applied requirements. TRL 3 NylonX, Flex TPE-185, and Nylon were unable to be reliably printed to fulfill testing. These results provide researchers with reference for materials to use during plant growth experimentation, and also set a standard for future characterization work applying 3D printing and materials to testing, research, and experimentation.

Gioia Massa↗
NASA NTRS2026

Aerodynamic Performance and Acoustic Impacts of Varying Tip Speeds and Tripping Conditions on Small Rotors in an Anechoic Hover Chamber

Performance and acoustic measurements were taken in a hover chamber for various optimum hovering rotors (OPT2) and a commercial-off-the-shelf (COTS) rotor. A total of 10 rotors are included in this report, all of which have two blades and a tip radius of 0.1905 m (7.5 in.). For the OPT2, results for three additive manufacturing methods of fabrication are presented: stereolithography(SLA) using Accura Xtreme, SLA using FormLabs 10K resin, and selective laser sintering (SLS) using mineral-filled PA12 nylon material. All but one set of rotors were designed with a trailing edge bluntness that is 3% of the chord length, and one set was designed with a bluntness that is 1% of the chord length. Spanwise boundary layer trips were applied to the SLA, FormLabs and COTS rotors. Performance comparisons between untripped and tripped configurations demonstrate the impact of boundary layer state on rotor efficiency. Acoustic results, including periodic and broadband noise components, are presented. The effects of tripping these rotors near the leading edge are also presented. For some of the rotors, acoustic spectra of tip speed sweeps are presented to show how the frequency content changes with tip speed. Amplitude and frequency scaling methods are used to collapse broadband spectra at various tip speeds towards a unified curve. These findings contribute to the understanding of small rotor aeroacoustics and provide valuable datasets for computational model validation in urban air mobility applications.

eVTOL↗
DOE OSTI2025

Mechanical Properties and Interfacial Bonding of Overmolded Polymer Composite Lattice Structures

This study investigates the mechanical properties and interfacial bonding of Polyamide 12 filled with Glass Fiber (PA12/GF) lattice structures overmolded with Nylon 66 (PA66) and Thermoplastic Polyurethane (TPU). The PA12/GF lattices, designed in Gyroid, Isotruss, and Octahedral geometries, were produced using the Selective Laser Sintering (SLS) technique. The thermal characteristics of both the lattice and overmolding materials were analyzed using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). The mechanical performance and interfacial bonding were evaluated through mechanical testing and microstructural analysis. The results indicate that overmolding improved flexural strength and impact resistance of the PA12/GF lattices. For instance, the plain PA12/GF Isotruss lattice exhibited a flexural strength of 15.5 MPa. By overmolding it with TPU the flexural strength increased by up to 137%, while PA66-overmolding resulted in an increase of 371%, achieving a flexural strength of 73 MPa. In terms of impact resistance, TPU-overmolding improved performance significantly, with an increase of 1800% (Gyroid) compared to the plain lattice. Microstructural analysis revealed good adhesion at the interface, especially when both the lattice and overmolding materials were thoroughly dried prior to the overmolding process to minimize interfacial porosity. This study highlights the potential of using overmolding to enhance lattice structures performance, offering lightweight and cost-efficient solutions for automotive applications.

Talabi, Isaac [ORNL] (ORCID:0000000340215594)↗
DOE OSTI2026

Catalytic Autoxidation for Depolymerization of Multilayer Plastic Films

Recycling multilayer plastic films is challenged by a diversity of polymers, prompting development of new recycling methods. For the depolymerization of mixed polymers like those in multilayer films, metal-catalyzed autoxidation offers a versatile chemical recycling method to deconstruct multiple polymers to useful oxygenates. Here, we demonstrate that catalytic autoxidation is effective for depolymerizing multilayer films across diverse chemistries. We investigated conditions for a model polyethylene substrate using a Co, Mn, and Br cocatalyst system, achieving full carbon closure with oxygenated small molecules contributing up to 48 mol% carbon. Subsequently, we characterized product distributions for several common polymers used in multilayer films using high-resolution mass spectrometry (HRMS) and developed analytical methods to quantify the resulting complex product streams. Optimized conditions for polyethylene were applied to 11 multilayer plastic films containing 10 different polymers, including films with nonpolymeric potential disrupters like aluminum foil and titanium dioxide, showing that catalytic autoxidation is effective across a broad range of polymer types and is resistant to disrupters and additives. The generation of CO 2 in these reactions overall suggests that both reaction engineering and modifications to the reaction conditions will be required to achieve higher yields of soluble oxygenated products.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical and Thermal Characterization of Additively Manufactured Carbon/Nylon 12 and Carbon/PEEK Composites

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Additive manufacturing↗
DOE OSTI2025

Integration of Metabolic and Bioprocess Engineering for the Production of B-Ketoadipic Acid from Glucose and Xylose by Pseudomonas Putida

..beta..-Ketoadipic acid is a common intermediate in aerobic microbial aromatic catabolism that can be used as a monomer in performance-advantaged biopolymers. Here, we engineered Pseudomonas putida KT2440 to produce ..beta..-ketoadipate from glucose and xylose, the most prevalent carbohydrates derived from lignocellulosic polysaccharides. With the top-performing strain, P. putida GR038, we conducted bioprocess development using glucose and xylose as substrates in a 2 : 1 molar ratio to mimic lignocellulosic hydrolysate. Fed-batch cultivations achieved a titer of 65.8 g L-1 and a rate of 0.69 g L-1 h-1, with a C-mol yield of 0.52. Application of adsorptive in situ product recovery further improved the effective titer to 92.0 g L-1 and the rate to 0.83 g L-1 h-1, while also improving the downstream purity of ..beta..-ketoadipate from 88.3 wt% to 99.0 wt%. These results show promise towards industrial production of ..beta..-ketoadipate from lignocellulosic sugars.

09 BIOMASS FUELS↗