Search NASA⌕ Search

SEARCH · Search NASA

Results for “outer planet missions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Ion Thruster Power Levels Extended by a Factor of 10

In response to two NASA Office of Space Science initiatives, the NASA Glenn Research Center is now developing a 7-kW-class xenon ion thruster system for near-term solar-powered spacecraft and a 25-kW ion engine for nuclear-electric spacecraft. The 7-kW ion thruster and power processor can be throttled down to 1 kW and are applicable to 25-kW flagship missions to the outer planets, asteroids, and comets. This propulsion system was scaled up from the 2.5-kW ion thruster and power processor that was developed successfully by Glenn, Boeing, the Jet Propulsion Laboratory (JPL), and Spectrum Astro for the Deep Space 1 spacecraft. The 7-kW ion thruster system is being developed under NASA's Evolutionary Xenon Thruster (NEXT) project, which includes partners from JPL, Aerojet, Boeing, the University of Michigan, and Colorado State University.

Patterson, Michael J.↗
NASA NTRS2005

Analysis of Chemical, REP, and SEP missions to the Trojan asteroids

Recent studies suggest significant benefits from using 1st and 2nd generation Radioisotope Power Systems (RPS) as a power source for electric propulsion (EP) missions to the outer planets. This study focuses on trajectories to the Trojan asteroids. A high level analysis is performed with chemical trajectories to determine potential canidates for REP trajectory optimization. Extensive analysis of direct trajectories using REP is performed on these candidates. Solar Electric Propulsion (SEP) trajectories are also considered for comparison against REP trajectories.

Trojan asteroids↗
NASA NTRS2004

Open-systems Architecture of a Standardized Command Interface Chip-set for Switching and Control of a Spacecraft Power Bus

This viewgraph presentation reviews the architecture of the The CIA-AlA chip-set is a set of mixed-signal ASICs that provide a flexible high level interface between the spacecraft's command and data handling (C&DH) electronics and lower level functions in other spacecraft subsystems. Due to the open-systems architecture of the chip-set including an embedded micro-controller a variety of applications are possible. The chip-set was developed for the missions to the outer planets. The chips were developed to provide a single solution for both the switching and regulation of a spacecraft power bus. The Open-Systems Architecture allows for other powerful applications.

power switch slice (PSS)↗
NASA NTRS2010

Planar Submillimeter-Wave Mixer Technology with Integrated Antenna

High-performance mixers at terahertz frequencies require good matching between the coupling circuits such as antennas and local oscillators and the diode embedding impedance. With the availability of amplifiers at submillimeter wavelengths and the need to have multi-pixel imagers and cameras, planar mixer architecture is required to have an integrated system. An integrated mixer with planar antenna provides a compact and optimized design at terahertz frequencies. Moreover, it leads to a planar architecture that enables efficient interconnect with submillimeter-wave amplifiers. In this architecture, a planar slot antenna is designed on a thin gallium arsenide (GaAs) membrane in such a way that the beam on either side of the membrane is symmetric and has good beam profile with high coupling efficiency. A coplanar waveguide (CPW) coupled Schottky diode mixer is designed and integrated with the antenna. In this architecture, the local oscillator (LO) is coupled through one side of the antenna and the RF from the other side, without requiring any beam sp litters or diplexers. The intermediate frequency (IF) comes out on a 50-ohm CPW line at the edge of the mixer chip, which can be wire-bonded to external circuits. This unique terahertz mixer has an integrated single planar antenna for coupling both the radio frequency (RF) input and LO injection without any diplexer or beamsplitters. The design utilizes novel planar slot antenna architecture on a 3- mthick GaAs membrane. This work is required to enable future multi-pixel terahertz receivers for astrophysics missions, and lightweight and compact receivers for planetary missions to the outer planets in our solar system. Also, this technology can be used in tera hertz radar imaging applications as well as for testing of quantum cascade lasers (QCLs).

Chattopadhyay, Gautam↗
NASA NTRS2008

Uplink Array Concept Demonstration with the EPOXI Spacecraft

Uplink array technology is currently being developed for NASA's Deep Space Network (DSN) to provide greater range and data throughput for future NASA missions, including manned missions to Mars and exploratory missions to the outer planets, the Kuiper belt, and beyond. Here we describe a novel technique for generating the frequency predicts that are used to compensate for relative Doppler, derived from interpolated earth position and spacecraft ephemerides. The method described here guarantees velocity and range estimates that are consistent with each other, hence one can always be recovered from the other. Experimental results have recently proven that these frequency predicts are accurate enough to maintain the phase of a three element array at the EPOXI spacecraft for three hours. Previous methods derive frequency predicts directly from interpolated relative velocities. However, these velocities were found to be inconsistent with the corresponding spacecraft range, meaning that range could not always be recovered accurately from the velocity predicts, and vice versa. Nevertheless, velocity-based predicts are also capable of maintaining uplink array phase calibration for extended periods, as demonstrated with the EPOXI spacecraft, however with these predicts important range and phase information may be lost. A comparison of the steering-vector method with velocity-based techniques for generating precise frequency predicts specifically for uplink array applications is provided in the following sections.

spacecraft uplink commands↗
NASA NTRS2008

Pointing-Vector and Velocity Based Frequency Predicts for Deep-Space Uplink Array Applications

Uplink array technology is currently being developed for NASA's Deep Space Network (DSN) to provide greater range and data throughput for future NASA missions, including manned missions to Mars and exploratory missions to the outer planets, the Kuiper belt, and beyond. Here we describe a novel technique for generating the frequency predicts that are used to compensate for relative Doppler, derived from interpolated earth position and spacecraft ephemerides. The method described here guarantees velocity and range estimates that are consistent with each other, hence one can always be recovered from the other. Experimental results have recently proven that these frequency predicts are accurate enough to maintain the phase of a three element array at the EPOXI spacecraft for three hours. Previous methods derive frequency predicts directly from interpolated relative velocities. However, these velocities were found to be inconsistent with the corresponding spacecraft range, meaning that range could not always be recovered accurately from the velocity predicts, and vice versa. Nevertheless, velocity-based predicts are also capable of maintaining uplink array phase calibration for extended periods, as demonstrated with the EPOXI spacecraft, however with these predicts important range and phase information may be lost. A comparison of the steering-vector method with velocity-based techniques for generating precise frequency predicts specifically for uplink array applications is provided in the following sections.

uplink arraying↗
NASA NTRS2012

Radiation Hard Bandpass Filters for Mid- to Far-IR Planetary Instruments

We present a novel method to fabricate compact metal mesh bandpass filters for use in mid- to far-infrared planetary instruments operating in the 20-600 micron wavelength spectral regime. Our target applications include thermal mapping instruments on ESA's JUICE as well as on a de-scoped JEO. These filters are novel because they are compact, customizable, free-standing copper mesh resonant bandpass filters with micromachined silicon support frames. The filters are well suited for thermal mapping mission to the outer planets and their moons because the filter material is radiation hard. Furthermore, the silicon support frame allows for effective hybridization with sensors made on silicon substrates. Using a Fourier Transform Spectrometer, we have demonstrated high transmittance within the passband as well as good out-of-band rejection [1]. In addition, we have developed a unique method of filter stacking in order to increase the bandwidth and sharpen the roll-off of the filters. This method allows one to reliably control the spacing between filters to within 2 microns. Furthermore, our method allows for reliable control over the relative position and orienta-tion between the shared faces of the filters.

Brown, Ari D.↗
NASA NTRS2015

Heliopause Electrostatic Rapid Transit System (HERTS)

A recent six month investigation focused on: "Determining the benefits of propelling a scientific spacecraft by an 'Electric Sail' propulsion system to the edge of our solar system (the Heliopause), a distance of 100 to 120 AU, in ten years or less" has recently been completed by the Advance Concepts Office at NASA's MSFC. The concept investigated has been named the Heliopause Electrostatic Rapid Transit System (HERTS) by the MSFC team. The HERTS is a revolutionary propellant-less propulsion concept that is ideal for deep space missions to the Outer Planets, Heliopause, and beyond. It is unique in that it uses momentum exchange from naturally occurring solar wind protons to propel a spacecraft within the heliosphere. The propulsion system consists of an array of electrically positively-biased wires that extend outward 20 km from a rotating (one revolution per hour) spacecraft. It was determined that the HERTS system can accelerate a spacecraft to velocities as much as two to three times that possible by any realistic extrapolation of current state-of-the-art propulsion technologies- including solar electric and solar sail propulsion systems. The data produced show that a scientific spacecraft could reach distances of 100AU in less than 10 years. Moreover, it can be reasonably expected that this system could be developed within a decade and provide meaningful Heliophysics Science and Outer Planetary Science returns in the 2025-2035 timeframe.

Wiegmann, Bruce M.↗
NASA NTRS2015

Electric Sail Propulsion for Exploring Nearby Interstellar Space

An Electric Sail is a revolutionary propellant-less propulsion system that is ideal for deep space missions to the outer planets, the Heliopause, and beyond. It is revolutionary in that it uses momentum exchange with the hypersonic solar wind to propel a spacecraft within the heliosphere. The momentum exchange is affected by the deflection of charged solar wind particles by an array of electrically biased wires that extend outward up to 30 km from a slowly rotating spacecraft. A high-voltage, positive bias on the wires, which are oriented normal to the solar wind flow, deflects the streaming protons, resulting in a reaction force on the wires that is also directed radially away from the sun. Over a period of months, this small force can accelerate the spacecraft to enormous speeds-on the order of 100-150 km/s (approximately 20 to 30 AU/yr). Unlike solar sails, Electric Sails do not rely on a fixed area to produce thrust. In fact, as they move away from the Sun and solar wind pressure decreases, the area for solar proton momentum transfer becomes larger, increasing system efficiency. As a result, thrust decreases at ≈1/r**(7/6) instead of the ≈1/r**2 rate typical for solar sails. The net effect is that an increased radial range of operation, together with increased thrust, both contribute to higher velocities and shorter total trip times to distant destinations. The MSFC Advanced Concepts Office (ACO) was awarded a Phase II NASA Innovative Advanced Concepts (NIAC) study to mature the technology for possible future demonstration and implementation. Preliminary results indicate that the physics of the system is viable and that a spacecraft propelled by an Electric Sail could reach the Heliopause in less than 15 years - and could be developed within a decade.

Johnson, Les↗
NASA NTRS2015

High Radiation Resistance IMM Solar Cell

Due to high launch costs, weight reduction is a key driver for the development of new solar cell technologies suitable for space applications. This project is developing a unique triple-junction inverted metamorphic multijunction (IMM) technology that enables the manufacture of very lightweight, low-cost InGaAsP-based multijunction solar cells. This IMM technology consists of indium (In) and phosphorous (P) solar cell active materials, which are designed to improve the radiation-resistant properties of the triple-junction solar cell while maintaining high efficiency. The intrinsic radiation hardness of InP materials makes them of great interest for building solar cells suitable for deployment in harsh radiation environments, such as medium Earth orbit and missions to the outer planets. NASA Glenn's recently developed epitaxial lift-off (ELO) process also will be applied to this new structure, which will enable the fabrication of the IMM structure without the substrate.

Pan, Noren↗
NASA NTRSDate not supplied

A Multiphysics Study to Improve Specific Energy of Primary Batteries for Low Temperature Operation for Deep Space Missions

Several lander missions on the outer planets such as Europa, Enceladus, and Titan require electrical power to operate scientific and communication equipment. The traditional power generation methods, such as a photovoltaic array, are not feasible as their efficiency drops significantly at these vast distances. The novel radioisotope power systems are not practical today based on current lander designs and the effectiveness of these systems. To perform in situ science on distant planets, a high specific energy battery (>700 Wh/kg) needs to operate for about 480 hours under cold temperatures (-40C or 0C) [1]. While a primary battery such as Li-CFx can provide high specific energy at room temperature, its specific capacity decreases significantly at low temperatures. One of the causes for this drop is low ion and electrical conductivity, and slower reaction kinetics. Slower transport and facile kinetics lead to an increase in the battery’s resistance and higher voltage drops during the cell operation, thus reducing specific capacity. Both the transport and kinetics show a strong dependence on temperature. Thus, a small temperature rise can lead to an increase in the reaction rate and ion conductivity; since the temperature, cell resistance, and specific capacity are interdependent. A conventional battery model accounts for ohmic, thermodynamic, and, electrochemical, and chemical decomposition heating. The ohmic heating can be controlled by designing a resistive microstructure and varying the ratios of the active materials [2]. The kinetics can be improved by increasing the surface area, reducing the particle size, or adding a catalyst. These parameters are often optimized to achieve high specific energy at room temperatures. A similar optimization study is not available at low temperatures and for a primary (high specific energy) battery. For this presentation, we will explore the effect of geometrical, microstructural, and material properties on optimal specific capacity at low temperatures through multiphysics simulations. The ion transport resistance depends on the porosity and the tortuosity of an electrode and the separator.

M. Mehta↗
NASA NTRSDate not supplied

Nuclear Fusion Space Propulsion Research, Experimentation, Theory Development, and Systems Analysis Efforts Led by the NASA Glenn Research Center (1994-2004)

This review paper summarizes work performed from 1994 to 2004 by a several interrelated government, academic, and industry teams led by the NASA Glenn Research Center. The nuclear fusion space propulsion system concept was predicated on a spherical torus reactor, which enabled manned missions to the outer planets in less than one year. Moderate thrust levels (1,000’s lbf)from direct nuclear fusion exhaust plasma via a magnetic nozzle enabled high thrust-to-weight. An entire vehicle conceptual design, including an artificial gravity crew habitat, was created by the NASA Glenn Research Center. The proof of concept experiment test article and facility upgrade was performed at the Ohio State University which also included staff from the Ohio Aerospace Institute and Science Applications International Corporation.The governing equations for the plasma physics theory of magnetic nozzle operation were derived by the Los Alamos National Laboratory. A preliminary investigation of a proof of concept test utilizing Coaxial Helicity Ejection as a means to supply plasma for propulsion at the National Spherical Torus Experiment reactor was outlined by the Princeton Plasma Physics Laboratory. An industry standard on nuclear fusion propulsion conceptual design was created by two AIAA teams. Despite extremely modest funding levels, significant progress was made advancing the state of the art.The result was a coordinated conceptual, theoretical, and experimental design effort to guide fusion space propulsion development.

Nuclear fusion↗
NASA NTRS1977

Voyager to Jupiter and Saturn

The NASA Voyager mission to explore planets of the outer solar system is summarized. The mission schedule and profiles for encounters with Jupiter and Saturn, and possibly with Uranus and Pluto are included along with a description of the spacecraft and its trajectories. Scientific investigations to be made and the instruments carried are also discussed.

Source record↗
NASA NTRSDate not supplied

Feasibility and Performance Analysis of Magnetohydrodynamic Control for Aerocapture at Neptune

Throughout the past few decades, the demand for farther and more massive missions have increased significantly, especially with the recent push for manned missions to Mars as well as the growing sci- entific interest in the outer giant planets and their re- spective moons. While spacecraft have successfully made it to the surface of Mars and into a flyby of the outer planets, the technologies from these missions are reaching the threshold of their capabilities. These tradi- tional methods are inadequate for higher mass and outer planetary missions due to the inherent propellant mass constraints of using fully-propulsive orbital insertion. Thus, there has been an ongoing effort to introduce new methods of deceleration and flight control during plan- etary EDL to reduce the required orbital insertion pro- pellant mass and enable new missions. One of the most prominently proposed solutions is aerocapture.

Danny Nguyen↗
NASA NTRS1973

Nuclear electric propulsion mission engineering study. Volume 1: Executive summary

Results of a mission engineering analysis of nuclear-thermionic electric propulsion spacecraft for unmanned interplanetary and geocentric missions are summarized. Critical technologies associated with the development of nuclear electric propulsion (NEP) are assessed. Outer planet and comet rendezvous mission analysis, NEP stage design for geocentric and interplanetary missions, NEP system development cost and unit costs, and technology requirements for NEP stage development are studied. The NEP stage design provides both inherent reliability and high payload mass capability. The NEP stage and payload integration was found to be compatible with the space shuttle.

Source record↗
NASA NTRS1975

Advanced bipropellant systems for use on planetary orbiters

Planetary orbit mission capabilities will be greatly improved by the advent of space-storable retro-propulsion systems with liquid fluorine/hydrazine as bipropellants, even when the Space Shuttle/Space Tug is used as launch vehicle. With a specific impulse as high as 375 sec, a multimission propulsion module designed for Pioneer or Mariner class spacecraft as payload and using space-storable propellants, can perform Mercury, Saturn and Uranus orbiter missions, and even some comet rendezvous missions. It also can reduce trip times to the outer planets significantly. The paper presents mission requirements, propulsion technology status, system design, performance, development schedules and cost data, based on results of a recent design and feasibility study.

Meissinger, H. F.↗
NASA NTRS1973

Automatic control in planetary exploration in the 1980s

Based on an examination of the planetary missions in the 1980s and their related objectives, a broad assessment of the automatic control capabilities required for these missions is presented. The ten outer-planet, terrestrial-planet, and small-body missions considered involve various operations encompassing a complex series of modes including cruise, maneuver, and powered flight control. In addition to routine navigation and attitude control, onboard control is required to point scientific instruments and antennas with respect to the vehicle and to maneuver the spacecraft in time-constrained or hazardous environments. These 1980 missions aimed at exploring new areas of the solar system will be more demanding. New design philosophies and increased performance capabilities will be required to meet the constraints imposed by science requirements and mission-cost effectiveness.

Moore, J. W.↗