Search NASA⌕ Search

SEARCH · Search NASA

Results for “pH indicators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Mass transfer coefficients, kL, and air-CO2 ingassing rates in 3.4 m2 and 1-acre raceway ponds.

The US DOE 2016 Billion Ton Update (Langholtz 2016) projected that CO2 in flue-gas from power plants or similar sources would limit U.S. algal biofuel potential to under 5 billion gallons gasoline equivalent (gge) per year, due to lack of sufficient land, water and other requirements near such flue gas sources. 2nd generation carbon capture technologies are proposed to overcome this constraint (Davis 2017), and could expand this resource potential nearly 10-fold, assuming CO2 costs near the future, 2025 DOE NETL, goal of $40/metric ton CO2. An alternative pathway is the direct uptake of air CO2 into the algal ponds through an increase in the air-CO2 transfer rate resulting from the reaction of CO2 with hydroxide ions. However, such a ‘chemical enhancement’ in mass transfer depends on a high pH in the culture, and, by extension, the ability of microalgae to maintain high rates of carbon assimilation under such conditions. Abiotic experiments characterized the air-CO2 mass-transfer rate in 1-acre and 3.4 m2 raceway ponds as a function of pH, with rates approaching 10 g C/m2-day at pH 12 in the brackish water tested, equivalent to a biomass productivity potential of near 20 g AFDW/m2-day (@ 0.47 g C/g AFDW). The mass transfer rate was found to be nearly independent of the mass-transfer coefficient, indicating that at turbulence levels achievable in typical raceway ponds, the system is reaction rate, rather than diffusion limited. In biotic trials with an unknown green microalga, biomass productivity in ponds receiving CO2 from only direct surface air-CO2 exchange averaged 5 +/- 0.5 g AFDW/m2-day in August - September central California conditions, about half-that of experimental controls fertilized with supplemental CO2. pH in the air-only treatment reached a maximum of 10.5, supporting a model predicted air-CO2 ingassing rate between 2-3 g C/m2-day, consistent with the observed biomass carbon assimilation rate. Results suggest that unique alkaliphilic strains are required if reliant on direct in-pond air-CO2 transfer for algal inorganic carbon supply, and that reaching an economically viable biomass productivity will require strains that thrive at pH 11 and above.

09 BIOMASS FUELS↗
DOE OSTI2020

Structure of the Diphtheria Toxin at Acidic pH: Implications for the Conformational Switching of the Translocation Domain

Diphtheria toxin, an exotoxin secreted by Corynebacterium that causes disease in humans by inhibiting protein synthesis, enters the cell via receptor-mediated endocytosis. The subsequent endosomal acidification triggers a series of conformational changes, resulting in the refolding and membrane insertion of the translocation (T-)domain and ultimately leading to the translocation of the catalytic domain into the cytoplasm. Here, we use X-ray crystallography along with circular dichroism and fluorescence spectroscopy to gain insight into the mechanism of the early stages of pH-dependent conformational transition. For the first time, we present the high-resolution structure of the diphtheria toxin at a mildly acidic pH (5–6) and compare it to the structure at neutral pH (7). We demonstrate that neither catalytic nor receptor-binding domains change their structure upon this acidification, while the T-domain undergoes a conformational change that results in the unfolding of the TH2–3 helices. Surprisingly, the TH1 helix maintains its conformation in the crystal of the full-length toxin even at pH 5. This contrasts with the evidence from the new and previously published data, obtained by spectroscopic measurements and molecular dynamics computer simulations, which indicate the refolding of TH1 upon the acidification of the isolated T-domain. The overall results imply that the membrane interactions of the T-domain are critical in ensuring the proper conformational changes required for the preparation of the diphtheria toxin for the cellular entry.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1979

Frost-weathering on Mars - Experimental evidence for peroxide formation

The weathering of silicates by frost is investigated in relation to the formation of surface peroxides to which Viking biology experiment results have been attributed. Samples of the minerals olivine and pyroxene were exposed to water vapor at -11 to -22 C and resultant gas evolution and pH were monitored. Experiments reveal the formation of an acidic oxidant upon interaction of the mineral and H2O frost at subfreezing temperatures, which chemical indicators have suggested to be chemisorbed hydrogen peroxide. A model for the formation of chemisorbed peroxide based on the chemical reduction of the mineral by surface frost is proposed, and it is predicted that the perioxide would decay at high temperatures to H2O and adsorbed O, consistent with the long-term storage and sterilization behavior of the soil oxidants observed in the Viking Gas Exchange and Labeled Release experiments.

Huguenin, R. L.↗
NASA NTRS1996

[Assessment of the risk factors for urolithiasis in cosmonauts during long flights]

Twelve cosmonauts flown aboard the Mir orbital station for 6-12 months and twelve candidates for cosmonauts were examined in an effort to determine a degree of urolithiasis risk. Prior to flight, on flight day 310 (in one cosmonaut) and after flight, the daily urinary excretion of the components influencing lithiasis formation was determined as well as a computer-aided calculation of urine saturation by lithogenic salts was performed (Ch. Pak, USA). In the in- and postflight periods, the greater number of indices under study were negatively changed in cosmonauts. Excretion dynamics of the lithogenesis inhibitors, i.e., citrates and magnesium, is of polar directionality. Frequency of deviations from the normal indices of urolithic risk in cosmonauts is primarily conditioned by low diuresis, urine supersaturation with calcium oxalate, undissociated uric acid, brushit, hypercalciuria, and changed pH.

Flight Experiment↗
NASA NTRS1996

Evidence for the Synthesis of ATP by an F0F1 ATP Synthase in Membrane Vesicles from Halorubrum Saccharovorum

Vesicles prepared in a buffer containing ADP, Mg(2+) and Pi synthesized ATP at an initial rate of 2 nmols/min/mg protein after acidification of the bulk medium (pH 8 (right arrow) 4). The intravesicular ATP concentration reached a steady state after about 30 seconds and slowly declined thereafter. ATP synthesis was inhibited by low concentrations of dicyclohexylcarbodiimide and m-chlorophenylhydrazone indicating that synthesis took place in response to the proton gradient. NEM and PCMS, which inhibit vacuolar ATPases and the vacuolar-like ATPases of extreme halophiles, did not affect ATP synthesis, and, in fact, produced higher steady state levels of ATP. This suggested that two ATPase activities were present, one which catalyzed ATP synthesis and one that caused its hydrolysis. Azide, a specific inhibitor of F0F1 ATP Synthases, inhibited halobacterial ATP synthesis. The distribution of acridine orange as imposed by a delta pH demonstrated that azide inhibition was not due to the collapse of the proton gradient due to azide acting as a protonophore. Such an effect was observed, but only at azide concentrations higher than those that inhibited ATP synthesis. These results confirm the earler observations with cells of H. saccharovorum and other extreme halophiles that ATP synthesis is inconsistent with the operation of a vacuolar-like ATPase. Therefore, the observation that a vacuolar-like enzyme is responsible for ATP synthesis (and which serves as the basis for imputing ATP synthesis to the vacuolar-like ATPases of the extreme halophiles, and the Archaea in general) should be taken with some degree of caution.

Faguy, David↗
NASA NTRS1995

Use of phosphoimidazolide-activated guanosine to investigate the nucleophilicity of spermine and spermidine

Guanosine 5'-phosphate 2-methylimidazolide (2-MeImpG), a labile phosphoimidazolide analog of guanosine triphosphate, was used to test the reactivity of the natural polyamines (PAs), spermine (spm) and spermidine (spd). The products are the guanosine 5'-phosphate-polyamine derivatives (PA-pG: spd-pG and spm-pG) which are quite stable in the range 4 < pH < 11. Our study is the first of which we are aware that reports on the nucleophilicity of these amines. The main findings are as follows. (i) HPLC analysis of the products indicates the formation of only two of the three possible spd products and only one of the two possible spm products. These results can be explained if only the primary amino groups of the two polyamines are reactive, while the secondary amino groups are rendered unreactive by a steric effect. The reactions of 2-MeImpG and other phosphoimidazolide derivatives of nucleosides (ImpNs) with primary and secondary monoamines support this interpretation (Kanavarioti et al. J. Org. Chem. 1995, 60, 632). (ii) The product ratio of the two spd-pG adducts derived from the primary amino groups varies between 2.40 and 0.71 in the range 6.1 < or equal to pH < or equal to 11.9. Such small variation in the product ratio can only be rationalized by the similar, but not identical, basicity of the two primary amino groups and provides strong support for a previously reported model for polyamine ionization (Onasch et. al. Biophys. Chem. 1984, 19, 245). (iii) On the basis of our kinetic determinations conditions at which the nucleophilicity of these amines is at a minimum and at which other interactions with ImpNs could be tested can be chosen.

NASA Discipline Exobiology↗
DOE OSTI2022

Plant organic matter inputs exert a strong control on soil organic matter decomposition in a thawing permafrost peatland

Peatlands are climate critical carbon (C) reservoirs that could become a C source under continued warming. A strong relationship between plant tissue chemistry and the soil organic matter (SOM) that fuels C gas emissions is inferred, but rarely examined at the molecular level. Here we compared Fourier transform infrared (FT-IR) spectroscopy measurements of solid phase functionalities in plants and SOM to ultra-high-resolution mass spectrometric analyses of plant and SOM water extracts across a palsa-bog-fen thaw and moisture gradient in an Arctic peatland. From these analyses we calculated the C oxidation state (NOSC), a measure which can be used to assess organic matter quality. Palsa plant extracts had the highest NOSC, indicating high quality, whereas extracts of Sphagnum, which dominated the bog, had the lowest NOSC. The percentage of plant compounds that are less bioavailable and accumulate in the peat, increases from palsa (25%) to fen (41%) to bog (47%), reflecting the pattern of percent Sphagnum cover. The pattern of NOSC in the plant extracts was consistent with the high number of consumed compounds in the palsa and low number of consumed compounds in the bog. However, in the FT-IR analysis of the solid phase bog peat, carbohydrate content was high implying high quality SOM. Here, we explain this discrepancy as the result of low solubilization of bog SOM facilitated by the low pH in the bog which makes the solid phase carbohydrates less available to microbial decomposition. Plant-associated condensed aromatics, tannins, and lignin-like compounds declined in the unsaturated palsa peat indicating decomposition, but lignin-like compounds accumulated in the bog and fen peat where decomposition was presumably inhibited by the anaerobic conditions. A molecular-level comparison of the aboveground C sources and peat SOM demonstrates that climate-associated vegetation shifts in peatlands are important controls on the mechanisms underlying changing C gas emissions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Environmental photosensitizers can exhibit enhanced actinic absorption in microhydrated clusters compared to solution

Brown carbon chromophores at environmental air-water interfaces often act as photosensitizers that absorb sunlight and subsequently transfer energy to nearby molecules, initiating a wide variety of chemical reactions. Despite their importance to understanding daytime chemistry at these airwater interfaces, little is known about the role of the solvation environment on the photophysical properties of these photosensitizers. In this work, we present a joint experimental-theoretical study of the vibrational and photophysical properties of microhydrated protonated and deprotonated 4-benzoylbenzoic acid (4-BBA), a key model system for environmental photosensitizers. We find that for protonated 4-BBAH + ∙(H 2 O) 0-1 , representing photosensitizers in very acidic conditions, a single bright state dominates the UV-Vis spectrum between 280 and 400 nm. Comparing the experimental UV-Vis spectra and quantum chemistry-predicted spectra of 4-BBA + ∙(H 2 O) 0-2 , we find that the degree of microhydration has little effect on the UV-Vis spectra or the orbitals of the dominant feature. For deprotonated 4-BBA ‒ , representing photosensitizers in basic conditions, quantum chemistry calculations predict that the UV-Vis spectra are ~3x weaker in intensity than the brightest 4-BBAH + ∙(H 2 O) 0-1 features and were not observed experimentally. Quantum chemistry calculations predict one dominant UV-Vis feature is present in the spectra of 4-BBA ‒ ∙(H 2 O) 0-2 , which exhibit minor shifts with degree of microhydration. While 4-BBA in bulk solution over a range of pH values has relatively weak absorption within the solar actinic region, we show that microhydrated 4-BBA has bright transitions within the actinic region. This indicates that the complex structure of environmental air-water interfaces can shift the absorption maximum of photosensitizers into the actinic region for enhanced absorption of sunlight and subsequent enhancement of photosensitizer-driven reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

High-throughput small-angle X-ray scattering reveals effective structure factor transitions linked to high-concentration antibody viscosity

High-concentration monoclonal antibody (mAb) formulations are often constrained by elevated viscosity, largely driven by protein–protein interactions, which complicates manufacturing and limits subcutaneous delivery. Early viscosity risk assessment is essential during discovery, yet traditional measurements require large sample volumes, and lack high-throughput capability. Here, we develop a high-throughput small-angle X-ray scattering (SAXS) protocol to detect mAb self-association at dilute concentrations, enabling early predictive insights into high-concentration viscosity. Synchrotron SAXS measurements were conducted for 21 mAbs formulated in a histidine buffer at pH 6.0. An initial subset of 10 mAbs analyzed across 1–150 mg/mL revealed that effective structure factor transitions in the low-q region, indicative of interparticle interactions, consistently emerged below 25 mg/mL. Subsequently, 11 additional mAbs were analyzed at 1–25 mg/mL using automated liquid handling and flow cells to enable high-throughput screening. High-viscosity mAbs exhibited detectable low-q upturns at concentrations ≤10 mg/mL, whereas low-viscosity mAbs showed downturns. A classification criterion based on effective structure factor transitions accurately classified all high- and low-viscosity mAbs at 150 mg/mL, offering a scalable, sample-efficient alternative to conventional methods. These results extend recent findings on the concentration-dependent sensitivity of SAXS to short-range attractions, demonstrating that they can emerge at lower concentrations than previously reported. This study presents the most comprehensive and diverse SAXS dataset for mAbs reported to date within a single formulation, providing a valuable resource for developing and validating coarse-grained models that can more accurately capture intermolecular interactions governing high-concentration solution behavior, thereby enabling rational antibody engineering and improved developability.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Characterization of long-term extension of isolated cell walls from growing cucumber hypocotyls

Walls from frozen-thawed cucumber (Cucumis sativus L.) hypocotyls extend for many hours when placed in tension under acidic conditions. This study examined whether such "creep" is a purely physical process dependent on wall viscoelasticity alone or whether enzymatic activities are needed to maintain wall extension. Chemical denaturants inhibited wall creep, some acting reversibly and others irreversibly. Brief (15 s) boiling in water irreversibly inhibited creep, as did pre-incubation with proteases. Creep exhibited a high Q10 (3.8) between 20 degrees and 30 degrees C, with slow inactivation at higher temperatures, whereas the viscous flow of pectin solutions exhibited a much lower Q10 (1.35). On the basis of its temperature sensitivity, involvement of pectic gel-sol transitions was judged to be of little importance in creep. Pre-incubation of walls in neutral pH irreversibly inactivated their ability to creep, with a half-time of about 40 min. At 1 mM, Cu2+, Hg2+ and Al3+ were strongly inhibitory whereas most other cations, including Ca2+, had little effect. Sulfhydryl-reducing agents strongly stimulated creep, apparently by stabilizing wall enzyme(s). The physical effects of these treatments on polymer interactions were examined by Instron and stress-relaxation analyses. Some treatments, such as pH and Cu2+, had significant effects on wall viscoelasticity, but others had little or no apparent effect, thus implicating an enzymatic creep mechanism. The results indicate that creep depends on relatively rugged enzymes that are firmly attached to or entangled in the wall. The sensitivity of creep to SH-reducing agents indicates that thiol reduction of wall enzymes might provide a control mechanism for endogenous cell growth.

NASA Program Space Biology↗
NASA NTRS2015

Aqueous Alteration on Mars: Evidence from Landed Missions

Mineralogical and geochemical data returned by orbiters and landers over the past 15 years have substantially enhanced our understanding of the history of aqueous alteration on Mars. Here, we summarize aqueous processes that have been implied from data collected by landed missions. Mars is a basaltic planet. The geochemistry of most materials has not been “extensively” altered by open-system aqueous processes and have average Mars crustal compositions. There are few examples of open-system alteration, such as Gale crater’s Pahrump Hills mudstone. Types of aqueous alteration include (1) acid-sulfate and (2) hydrolytic (circum-neutral/alkaline pH) with varying water-to-rock ratios. Several hypotheses have been suggested for acid-sulfate alteration including (1) oxidative weathering of ultramafic igneous rocks containing sulfides; (2) sulfuric acid weathering of basaltic materials; (3) acid fog weathering of basaltic materials; and (4) near-neutral pH subsurface solutions rich in Fe (sup 2 plus) that rapidly oxidized to Fe (sup 3 plus) producing excess acidity. Meridiani Planum’s sulfate-rich sedimentary deposit containing jarosite is the most “famous” acid-sulfate environment visited on Mars, although ferric sulfate-rich soils are common in Gusev crater’s Columbia Hills and jarosite was recently discovered in the Pahrump Hills. An example of aqueous alteration under circum-neutral pH conditions is the formation of Fe-saponite with magnetite in situ via aqueous alteration of olivine in Gale crater’s Sheepbed mudstone. Circum-neutral pH, hydrothermal conditions were likely required for the formation of Mg-Fe carbonate in the Columbia Hills. Diagenetic features (e.g., spherules, fracture filled veins) indicate multiple episodes of aqueous alteration/diagenesis in most sedimentary deposits. However, low water-to-rock ratios are prominent at most sites visited by landed missions (e.g., limited water for reaction to form crystalline phases possibly resulting in large amounts of short-range ordered materials and little physical separation of primary and secondary materials). Most of the aqueous alteration appears to have occurred early in the planet’s history; however, minor aqueous alteration may be occurring at the surface today (e.g., thin films of water forming carbonates akin to those discovered by Phoenix).

Ming, Douglas W.↗
NASA NTRSDate not supplied

Constraining the Hydration of X-Ray Amorphous and Clay Mineral Phases in Gale Crater, Mars

Clay minerals and salts in the Gale crater stratigraphy investigated by the Mars Science Laboratory (MSL) Curiosity rover preserve information about sediment sources, depositional environment, and post-depositional alteration history. The compositions of amorphous components in samples have bearing on the redox potential, pH, and chemistry of alteration fluids, and on the heterogeneity of these conditions. Interlayer clay hydration in present-day Gale crater could be an indication of high water/rock ratios of late-stage fluid alteration events, which increases the potential habitability of these post-depositional environments. The MSL Dynamic Albedo of Neutrons instrument (DAN) measures bulk hydration and here we attempt to determine the hydration states of both clay minerals and amorphous components throughout the Curiosity traverse to constrain the abundance of individual amorphous phases and determine if clay interlayer water is present today. These implications are also more broadly applicable to similar sedimentary successions outside Gale crater. In this study, we compare hydration results from DAN to mineralogical results from the MSL Chemistry and Mineralogy instrument (CheMin) for 16 different fluvio-lacustrine sample locations. These samples typically contain one or more hydrated crystalline phases, a hydrated X-ray amorphous fraction composed of multiple amorphous phases, and one or more clay mineral phases which CheMin has consistently measured as collapsed (i.e., no interlayer water). However, Gale samples are known to dehydrate during sample acquisition and handling, and because DAN measures hydration to a depth of tens of cm, we can test for the presence of clay interlayer water in situ by comparing DAN bulk hydration to CheMin mineralogy. We can also constrain the hydration of the samples’ amorphous fractions, and with geochemical data from the ChemCam and APXS instruments, this will allow us to better define the phases which compose this fraction.

S Czarnecki↗
DOE OSTI2020

Surface Reactivity Analysis of the Crude Oil–Brine–Limestone Interface for a Comprehensive Understanding of the Low-Salinity Waterflooding Mechanism

Low-salinity waterflooding (LSWF) has proven to improve oil recovery in carbonate formations through rock wettability alteration, although the underlying mechanism remains elusive. Multivalent ionic exchange and calcite dissolution have usually been investigated using geochemical analysis in secondary coreflooding. In this work, coreflooding, in tertiary mode, coupled with a surface reactivity analysis approach was employed to investigate the interplay of wettability alteration mechanisms such as mineral dissolution, electrostatic bond attraction, and the effect of pH at in situ conditions. Improved oil recovery (IOR) in tertiary mode observed by coreflooding in Indiana limestone rocks showed an ionic strength dependence, that is, reducing brine ionic strength resulted in an increase in oil recovery. Coreflooding results showed that the seawater and low-salinity brines deprived of Mg 2+ ions resulted in the lowest IOR in tertiary mode, indicating the significance of Mg 2+ on IOR in limestone rocks. Similar results were observed through the contact angle measurement showing the limestone rock wettability state dependence on ionic strength and the effect of Mg2+ ions. Surface reactivity analysis showed an increase in solution pH, Ca 2+ and Mg 2+ ions concentration in the effluent solution from the coreflooding in tertiary mode using low salinity brines (about 40 and 20% increase in the effluent composition for Ca 2+ and Mg 2+ , respectively). These changes in solution composition were used to calculate the in situ oil–brine and rock–brine zeta potential using a validated surface complexation model, showing the changes of zeta potential as brine is injected into limestone rocks. The results show that using seawater-like brine in tertiary mode resulted in no mineral dissolution or ionic exchange. However, improved oil recovery (IOR) using such seawater-like brine was due to wettability alteration caused by reduced electrostatic bond attraction associated with Mg 2+ ions [from 2.6 × 10 –13 (mol/m 2 ) 2 for formation water salinity to 1.5 × 10 –13 (mol/m 2 ) 2 for seawater salinity]. Using low-salinity brines in tertiary mode improved oil recovery by mineral dissolution, resulting in oil desorption and an increase in solution pH. Finally, the increase in solution pH also resulted in reduced electrostatic bond attraction which lead to rock wettability alteration using low-salinity brines.

04 OIL SHALES AND TAR SANDS↗
NASA NTRS1977

Light energy conservation processes in Halobacterium halobium cells

Proton pumping driven by light or by respiration generates an electrochemical potential difference across the membrane in Halobacterium halobium. The pH changes induced by light or by respiration in cell suspensions are complicated by proton flows associated with the functioning of the cellular energy transducers. A proton-per-ATP ratio of about 3 is calculated from simultaneous measurements of phosphorylation and the proton inflow. This value is compatible with the chemiosmotic coupling hypothesis. The time course of the light-induced changes in membrane potential indicates that light-driven pumping increases a dark pre-existing potential of about 130 mV only by a small amount (20 to 30 mV). The complex kinetic features of the membrane potential changes do not closely follow those of the pH changes, which suggests that flows of ions other than protons are involved. A qualitative model consistent with the available data is presented.

Bogomolni, R. A.↗
DOE OSTI2023

Mechanisms of dissolution from gibbsite step edges elucidated by ab initio molecular dynamics with enhanced sampling

Surface reactions underpin our collective understanding of mineral dissolution. This impacts a range of predictive geochemical models (for weathering, the fate and transport of metals) as well as industrial utilization of minerals. Yet atomistic details are rarely known due to the complex mineral/fluid interfacial environment. There is significant need to understand the mechanistic details of dissolution reactions and how they depend on surface morphology and solution conditions. This work utilizes surface pit models in conjunction with changes to solution composition that mimic pH to explore surface detachment of aluminate from gibbsite, which is a primary source of Al in soils and within the industrial processing of aluminum. Ab initio molecular dynamics simulations with enhanced sampling has been used to explore the detailed process of the detachment, the results of which indicate two potential pathways that are differentiated based upon the extent of water hydration. Here, the heights of the energy barriers depend upon the local morphology which influence the number of bridges (quasi-)simultaneously broken (1 or 2) or the Al-O coordination of the neighboring aluminum atoms (5 or 6) at the armchair edge. pH effects are significant, with a nearly 50% reduction in barrier height under alkaline conditions that are relevant to geothermal fluids and Al extraction from minerals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Tracking Metabolic Changes in Microbial Culture using Redox Measurements

During long-term space missions, microbial cultures accumulate the effects of low-dose radiation, microgravity, and other factors; altered growth and metabolic activity may occur before viability effects. This could affect functionality of bioreactors or other bio-enabled mission systems, as well as shed light on human health. Spaceflight microbiology studies beyond the low Earth orbit exposure afforded by the ISS have been limited. Nanosatellites offer an increasingly popular alternative for deep space missions. However, the communications delay requires biofluidic automation of a pre-defined experimental protocol, and the lack of sample return (reliance on sensors in flight) can significantly limit feasible investigations. Previous biological CubeSats (PharmaSat, O/OREOS, EcAMSat) have used alamarBlue, an off-the-shelf formulation of the redox indicator dye resazurin, to track metabolic activity, as will BioSentinel, the upcoming interplanetary microbiology experiment. A series of ground experiments (see abstracts by Liddell, Santa Maria, and A. Kim) were conducted using a microbial culture system outfitted with an electrochemical sensor array (electrical conductivity, pH, oxidation-reduction potential, and dissolved oxygen) with alamarBlue and the same strain of Saccharomyces cerevisiae as BioSentinel. By improving mapping of measured changes in alamarBlue kinetics to physicochemical changes, and ultimately to biological alterations such as shifted metabolic pathways, this work supplements data analyses from past missions and planning for future missions using alamarBlue to characterize space radiation effects. Initial results indicate that alamarBlue acts like a redox buffer; its presence significantly changes redox kinetics in otherwise identical cultures. The initial color change (blue resazurin reduced to red/pink resorufin) appears as a redox plateau. A second plateau, likely corresponding to the second color transition (resorufin to the colorless hydroresorufin), occurs at a lower redox value. The relationship to carbon source exhaustion, dissolved oxygen depletion, cell death, and measured redox potential is complex and still under study.

Tracking↗
DOE OSTI2025

Investigation of the iodate sorption mechanism by CoAl LDH through experiments and ab initio molecular dynamics simulations

Radioiodine released during the nuclear-fuel cycle constitutes a persistent radiological hazard. In this study, the IO 3 – uptake mechanism of CoAl LDH was resolved by combining pH-controlled sorption experiments, synchrotron XAFS, and DFT-based AIMD simulations. At pH close to 6, approximately 90% of IO 3 – was removed, and the equilibrium distribution coefficient reached about 1.7 × 10 4 mL g –1 . EXAFS analysis indicated an average iodine–oxygen bond length of 1.81 Å and a coordination number near 3, with the fit R-factor equal to 0.002. The simulations faithfully reproduced the experimental spectrum and revealed transient proton hopping events that generated metastable I–O–H species inside the interlayer, thereby confirming nitrate-to-iodate exchange as the controlling capture pathway. Atomic density profiles and radial distribution functions further showed that IO 3 – adopt an end-on orientation perpendicular to the hydroxide sheets, while water molecules mediate proton migration without disturbing the host lattice. In conclusion, the integrated experimental–computational evidence demonstrates that CoAl LDH can rapidly and selectively sequester IO 3 – under near-neutral conditions, offering atomic scale guidance for the rational engineering of layered sorbents for advanced radioactive-waste treatment.

Kang, Jaehyuk [Jeju National Univ. (Korea, Republi↗
DOE OSTI2020

An Electrochemically Mediated Amine Regeneration Process with a Mixed Absorbent for Postcombustion CO 2 Capture

Electrochemically mediated amine regeneration (EMAR) was recently developed to avoid the use of thermal means to release CO2 captured from postcombustion flue gas in the benchmark amine process. To address concerns related to the high vapor pressure of ethylenediamine (EDA) as the primary amine used in EMAR, a mixture of EDA and aminoethylethanolamine (AEEA) was investigated. The properties of the mixed amine systems, including the absorption rates, electrolyte pH and conductivity, and CO2 capacity, were evaluated in comparison with those of solely EDA. The mixed amine system had similar properties to that of EDA, indicating no significant changes would be necessary for the future implementation of the EMAR process with mixed amines as opposed to that with just EDA. The electrochemical performance of the mixed amines in terms of the cell voltage, gas desorption rate, electron utilization, and energetics was also investigated. A 50/50 mixture of EDA and AEEA displayed the lowest energetics: ~10% lower than that of 100% EDA. With this mixture, a continuous EMAR process, in which the absorption column was connected to the electrochemical cell as the desorption stage, was tested over 100 h. The cell voltage was very stable and there was a steady gas output close to theoretical values. The desorbed gas was further analyzed and found to be 100% CO2, confirming no evaporation of the amine. The mixed absorbent composition was also characterized using titration and nuclear magnetic resonance (NMR) spectroscopy, and the results showed no amine degradation. Furthermore, these findings that demonstrate a stable, low vapor pressure absorbent with improved energetics are promising and could be a guideline for the future development of EMAR for CO2 capture from flue gas and other sources.

54 ENVIRONMENTAL SCIENCES↗