Search NASA⌕ Search

SEARCH · Search NASA

Results for “partial derivative”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Evidence for Smectite Clays from MSL SAM Analyses of Mudstone at Yellowknife Bay, Gale Crater, Mars

Drilled samples of mudstone from the Sheepbed unit at Yellowknife Bay were analyzed by MSL instruments including the Sample Analysis at Mars (SAM) and Chemistry and Mineralogy (CheMin) instruments in MSL's Analytical Laboratory. CheMin analyses revealed the first in situ X-ray diffraction based evidence of clay minerals on Mars, which are likely trioctahedral smectites (e.g., saponite) and comprise approx 20% of the mudstone sample (e.g., Bristow et al., this meeting). SAM analyses, which heated the mudstone samples to 1000 C and monitored volatiles evolved to perform in situ evolved gas analysis mass spectrometry (EGA-MS), resulted in a H2O trace exhibiting a wide evolution at temperatures < 500 C, and an evolution peak at higher temperatures near approx 750 C. The low temperature H2O evolution has many potential contributors, including adsorbed H2O, smectite interlayer H2O, and structural H2O/OH from bassanite and akaganeite (identified by CheMin) and H2O/OH from amorphous phases in the sample. The high temperature H2O is consistent with the evolution of H2O from the dehydroxylation of the smectite clay mineral. Comparison to EGA-MS data collected under SAM-like conditions on a variety of clay mineral reference materials indicate that a trioctahedral smectite, such as saponite, is most consistent with the high temperature H2O evolution observed. There may also be SAM EGA-MS evidence for a small high temperature H2O evolution from scoop samples from the Yellowknife Bay Rocknest sand shadow bedform. As in the mudstone samples, this evolution may indicate the detection of smectite clays, and the idea that minor clays may be present in Rocknest materials that could be expected to be at least partially derived from local sources is reasonable. But, because smectite clays were not definitively observed in CheMin analyses of Rocknest materials, they must be present at much lower abundances than the approx 20% observed in the mudstone samples. This potential detection underscores the complementary nature of the MSL CheMin and SAM instruments for investigations of martian sample mineralogy. Information on the nature of Yellowknife Bay clay minerals may also be available from the detection of H2 evolved during SAM EGA-MS at high temperature. A likely source of at least some of this H2 is H2O evolved from the smectite clays at high temperature, and it is possible these evolutions can be used in a similar fashion to high temperature H2O releases to provide constraints on the clay minerals in a sample. In addition, the D/H of this high temperature H2, as well as the H2O, can be derived from SAM MS and Tunable Laser Spectrometer (TLS) data, respectively. These D/H values may help to inform the provenance of high and low temperature water evolved from martian samples

McAdam, Amy↗

Comparison of the Sensitivity of Surface Downward Longwave Radiation to Changes in Water Vapor at Two High Elevation Sites

Among the potential reasons for enhanced warming rates in many high elevation regions is the nonlinear relationship between surface downward longwave radiation (DLR) and specific humidity (q). In this study we use ground-based observations at two neighboring high elevation sites in Southwestern Colorado that have different local topography and are 1.3 kilometers apart horizontally and 348 meters vertically. We examine the spatial consistency of the sensitivities (partial derivatives) of DLR with respect to changes in q, and the sensitivities are obtained from the Jacobian matrix of a neural network analysis. Although the relationship between DLR and q is the same at both sites, the sensitivities are higher when q is smaller, which occurs more frequently at the higher elevation site. There is a distinct hourly distribution in the sensitivities at both sites especially for high sensitivity cases, although the range is greater at the lower elevation site. The hourly distribution of the sensitivities relates to that of q. Under clear skies during daytime, q is similar between the two sites, however under cloudy skies or at night, it is not. This means that the DLR-q sensitivities are similar at the two sites during daytime but not at night, and care must be exercised when using data from one site to infer the impact of water vapor feedbacks at another site, particularly at night. Our analysis suggests that care should be exercised when using the lapse rate adjustment to infill high frequency data in a complex topographical region, particularly when one of the stations is subject to cold air pooling as found here.

elevation↗

A Universal Threshold for the Assessment of Load and Output Residuals of Strain-Gage Balance Data

A new universal residual threshold for the detection of load and gage output residual outliers of wind tunnel strain{gage balance data was developed. The threshold works with both the Iterative and Non{Iterative Methods that are used in the aerospace testing community to analyze and process balance data. It also supports all known load and gage output formats that are traditionally used to describe balance data. The threshold's definition is based on an empirical electrical constant. First, the constant is used to construct a threshold for the assessment of gage output residuals. Then, the related threshold for the assessment of load residuals is obtained by multiplying the empirical electrical constant with the sum of the absolute values of all first partial derivatives of a given load component. The empirical constant equals 2.5 microV/V for the assessment of balance calibration or check load data residuals. A value of 0.5 microV/V is recommended for the evaluation of repeat point residuals because, by design, the calculation of these residuals removes errors that are associated with the regression analysis of the data itself. Data from a calibration of a six-component force balance is used to illustrate the application of the new threshold definitions to real{world balance calibration data.

wind tunnel balance↗

Pre-Test Assessment of the Upper Bound of the Drag Coefficient Repeatability of a Wind Tunnel Model

A new method is presented that computes a pre{test estimate of the upper bound of the drag coefficient repeatability of a wind tunnel model. This upper bound is a conservative estimate of the precision error of the drag coefficient. For clarity, precision error contributions associated with the measurement of the dynamic pressure are analyzed separately from those that are associated with the measurement of the aerodynamic loads. The upper bound is computed by using information about the model, the tunnel conditions, and the balance in combination with an estimate of the expected output variations as input. The model information consists of the reference area and an assumed angle of attack. The tunnel conditions are described by the Mach number and the total pressure or unit Reynolds number. The balance inputs are the partial derivatives of the axial and normal force with respect to all balance outputs. Finally, an empirical output variation of 1.0 microV/V is used to relate both random instrumentation and angle measurement errors to the precision error of the drag coefficient. Results of the analysis are reported by plotting the upper bound of the precision error versus the tunnel conditions. The analysis shows that the influence of the dynamic pressure measurement error on the precision error of the drag coefficient is often small when compared with the influence of errors that are associated with the load measurements. Consequently, the sensitivities of the axial and normal force gages of the balance have a significant influence on the overall magnitude of the drag coefficient's precision error. Therefore, results of the error analysis can be used for balance selection purposes as the drag prediction characteristics of balances of similar size and capacities can objectively be compared. Data from two wind tunnel models and three balances are used to illustrate the assessment of the precision error of the drag coefficient.

drag coefficient measurement↗

Implicit Formulation of Muscle Dynamics in OpenSim

Astronauts lose bone and muscle mass during spaceflight. Exercise countermeasure is the primary method for counteracting bone and muscle mass loss in space. New spacecraft exercise device concepts are currently being developed for the NASAs new crew exploration vehicle. The NASA Digital Astronaut Project (DAP) uses computational modeling to help determine if the new exercise devices will be effective as countermeasures. The NASA Digital Astronaut Project is developing the ability to utilize predictive simulation to provide insight into the change in kinematics and kinetics with a change in device and gravitational environment (1-g versus 0-g). For example, in space exercise the subject's body weight is applied in addition to the loads prescribed for musculoskeletal maintenance. How and where these loads are applied obviously directly impacts bone and tissue loads. Additionally, due to space vehicle structural requirements, exercise devices are often placed on vibration isolation systems. This changes the apparent impedance or stiffness of the device as seen by the user. Data collection under these conditions is often impractical and limited. Predictive modeling provides a means to have a virtual subject to test hypotheses. Predictive simulation provides a virtual subject for which we are able to perform studies such as sensitivity to device loading and vibration isolation without the need for laboratory kinematic or kinetic test data.Direct Collocation optimization provides an efficient means to perform task based optimization and predictive modeling. It is relatively straight forward to structure a physical exercise task in a Direct Collocation mathematical formulation: perform a motion such that you start at an initial pose, achieve a given amount of deflection i.e a squat, return to the initial pose, and minimize muscle activation cost. Direct Collocation is advantageous in that it does not require numerical integration to evaluate the objective function. Instead, the system dynamics are transformed to discrete time and the optimizer is constrained such that the solution is not considered to be a valid unless the dynamic equations are satisfied at all time points. The simulation and optimization are effectively done simultaneously. Due to the implicit integration, time steps can be more coarse than in a differential equation solver. In a gait scenario this means that that the model constraints and cost function are evaluated at 100 nodes in the gait cycle versus 10,000 integration steps in a variable-step forward dynamic simulation. Furthermore, no time is wasted on accurate simulations of movements that are far from the optimum. Constrained optimization algorithms require a Jacobian matrix that contains the partial derivatives of each of the dynamic constraints with respect to of each of the state and control variables at all time points. This is a large but sparse matrix. An implicit dynamics formulation requires computation of the dynamic residuals f as a function of the states x and their derivatives, and controls u:f(x, dxdt, u) 0If the dynamics of musculoskeletal system are formulated implicitly, the Jacobian elements are often available analytically, eliminating the need for numerical differentiation; this is obviously computationally advantageous. Additionally, implicit formulation of musculoskeletal dynamics do not suffer from singularities from low mass bodies, zero muscle activation, or other stiff system or

physical exercise↗

Efficient Trajectory Propagation for Orbit Determination Problems

Regularized formulations of orbital motion apply a series of techniques to improve the numerical integration of the orbit. Despite their advantages and potential applications little attention has been paid to the propagation of the partial derivatives of the corresponding set of elements or coordinates, required in many orbit-determination scenarios and optimization problems. This paper fills this gap by presenting the general procedure for integrating the state-transition matrix of the system together with the nominal trajectory using regularized formulations and different sets of elements. The main difficulty comes from introducing an independent variable different from time, because the solution needs to be synchronized. The correction of the time delay is treated from a generic perspective not focused on any particular formulation. The synchronization using time-elements is also discussed. Numerical examples include strongly-perturbed orbits in the Pluto system, motivated by the recent flyby of the New Horizons spacecraft, together with a geocentric flyby of the NEAR spacecraft.

numerical methods↗

Development of an Integrated Nonlinear Aeroservoelastic Flight Dynamic Model of the NASA Generic Transport Model

This paper describes a recent development of an integrated fully coupled aeroservoelastic flight dynamic model of the NASA Generic Transport Model (GTM). The integrated model couples nonlinear flight dynamics to a nonlinear aeroelastic model of the GTM. The nonlinearity includes the coupling of the rigid-body aircraft states in the partial derivatives of the aeroelastic angle of attack. Aeroservoelastic modeling of the control surfaces which are modeled by the Variable Camber Continuous Trailing Edge Flap is also conducted. The R.T. Jones' method is implemented to approximate unsteady aerodynamics. Simulations of the GTM are conducted with simulated continuous and discrete gust loads..

Aeroservoelasticit↗

Implementation and Use of a Convergence Test for Iterative Wind Tunnel Balance Load Predictions

A modified and extended version of a convergence test for wind tunnel strain-gage balance load iterations was implemented. The test uses an upper bound of the Lipschitz constant to assess convergence characteristics of balance load predictions if the Iterative Method is applied. Convergence is expected within the use envelope of the balance whenever this upper bound is less than the threshold of one. It is explained in great detail how the convergence test can be applied to the two load iteration equation types that are currently being used in the aerospace testing community. In addition, the application of the test to balances with bi-directional output characteristics is discussed. It is also shown how numerical differentiation can be used in order to obtain partial derivatives that are needed for the calculation of the Lipschitz constant. Finally, machine calibration data of NASA's MC60E six-component force balance is selected to demonstrate both implementation and use of the convergence test.

calibration analysis↗

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗

Sensitivity Analysis Method to Address User Disparities in the Analytic Hierarchy Process

Decision makers often face complex problems, which can seldom be addressed well without the use of structured analytical models. Mathematical models have been developed to streamline and facilitate decision making activities, and among these, the Analytic Hierarchy Process (AHP) constitutes one of the most utilized multi-criteria decision analysis methods. While AHP has been thoroughly researched and applied, the method still shows limitations in terms of addressing user profile disparities. A novel sensitivity analysis method based on local partial derivatives is presented here to address these limitations. This new methodology informs AHP users of which pairwise comparisons most impact the derived weights and the ranking of alternatives. The method can also be applied to decision processes that require the aggregation of results obtained by several users, as it highlights which individuals most critically impact the aggregated group results while also enabling to focus on inputs that drive the final ordering of alternatives. An aerospace design and engineering example that requires group decision making is presented to demonstrate and validate the proposed methodology.

Marie Ivanco↗

Comparison of EKF and UKF for Robotic Missions to Mars

The batched Kalman lter works well for a wide variety of orbit determination scenarios but requires linearized approximations to the underlying dynamical system. Furthermore, implementation depends on the computation of partial derivatives for all measurements and parameters used in the lter, a non-trivial task even when analytical derivations are possible. To address these limitations, many extensions and modi - cations to the linear Kalman lter have been proposed over the years since Kalman's initial publication. Our investigation examines two popular variants of the Kalman lter, namely the Extended Kalman Filter (EKF) and Unscented Kalman Filter (UKF), within the context of spacecraft missions to Mars. The EKF relies on the same mathematical basis as the classic version of the lter, however it sequentially updates the linearization as the ltering process is conducted. In contrast, the UKF is built upon the unscented transform which samples the nearby solution space and numerically propagates perturbed trajectories as part of the update / estimation process. We assess the performance of the ltering algorithms under a variety of mission scenarios with the goal of establishing decision criteria for which implementation to use under di ering circumstances.

Ely, Todd↗

Efficient method for approximating nonlinear dynamics: applications to uncertainty propagation and estimation

High-order Taylor series expansions can be used to model nonlinear dynamics at the cost of integrating a large set of variational equations to obtain high-order state-transition tensors (STTs). This paper presents an innovative technique for approximating the high-order STTs that reduces significantly the computational cost by retaining only the dominant secular terms. We propagate the low-order partial derivatives of Kepler’s equation, which only requires the integration of six additional equations to extend an n-th order approximation to order (n + 1). The approximation stems from the Lindstedt-Poincare procedure and exploits the stability properties of orbital motion. Since the method makes no dynamical assumptions, it can accommodate any source of orbital perturbations. We show how the approximation of the second-order STT significantly increases the accuracy of the linear method for uncertainty propagation with only a small computational overhead. Finally, we derive a high-order approximate extended Kalman filter that implements the proposed approximation of the STT and improves the performance of linear filters. Examples of application with different perturbation sources include the heliocentric orbit of an asteroid, an orbiter around Europa, and an Earth-orbiting satellite.

Park, Ryan S↗

Secondary Sonic Boom Ray Path Prediction using sBOOM

Sonic boom ray path equations are solved numerically to show the extent of secondary booms compared to primary sonic boom carpet. Secondary booms are shown to reach altitudes of ~125 km before turning toward the ground and impinging at lateral distances of ~50 km and beyond. Exact closed-form solutions of the ray paths and their partial derivatives with respect to certain relevant parameters are derived for the simplified case of windless atmospheres and compared against numerical solutions. Ray tube areas are computed using the Jacobian of a single ray as opposed to the traditional technique of using 4 rays that are temporally and azimuthally perturbed. The ray tube areas corresponding to secondary booms can get 1000 times larger than those from primary booms. The numerically computed ray tube areas are verified using exact expressions for the special case of windless atmospheres. Finally, pressure scaling due to ray tube area changes and atmospheric stratification is presented and the shortcomings associated with the current atmospheric interpolation techniques are discussed. It is determined that piece-wise linear interpolation of the atmospheric temperature may be inadequate and could lead to numerical noise in the prediction of secondary booms.

Sriram K Rallabhandi↗

Turbulent mixing and entrainment in a gravity current

We present an experimental study of the mixing processes in a gravity current. The turbulent transport of momentum and buoyancy can be described in a very direct and compact form by a Prandtl mixing length model: the turbulent vertical fluxes of momentum and buoyancy are found to scale quadratically with the vertical mean gradients of velocity and density. The scaling coefficient is the square of the mixing lenth, approximately constant over the mixing zone of the stratified shear layer. We show how, in different flow configurations, this length can be related to the shear length of the flow ({var_epsilon}/{partial_derivative}{sub z}u{sup 3}){sup 1/2}. We also study the fluctuations of the momentum and density turbulent fluxes, showing how they relate to the mixing phenomena, and to the entrainment/detrainment balance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

FDEM v.1.0

Algorithm FOEM numerically solves a system of six, coupled, first-order, linear, inhomogeneous partial differential equations (called the "EH-system") with an explicit, time-domain, finite-difference (FD) The six dependent variables three electric field vector components and three magnetic field FOEM vector components) are stored on staggered spatial and temporal grids. Discrete FO operators approximating the partial derivatives possess 2nd-order accuracy in time and Nth-order accuracy in space. The 3D spatial grid is rectangular, and grid intervals are uniform in each coordinate direction. FD formulae for updating the wavefield variables are appropriately non-dimensionalized and normalized so that single-precision arithmetic calculations yield adequate accuracy. This software will be used to generate electromagnetic responses for typical geological/geophysical models of interest in the petroleum, mining, geotechnical, geothermal, hydrological, environmental assessment, and underground storage industries. Additionally, US government agencies (including the military) involved in monitoring of explosions (chemical or nuclear) or remote surveillance of underground facilities may be interested in using algorithm FOEM. Finally, this software may be of use to organizations involved in fundamental research and applications development in the area of electromagnetic wave propagation (e.g. national laboratories, academic departments. industry).

Source record↗

ELASTI

The mathematical underpinning of algorithm ELASTI is the so-called velocity-stress system of coupled partial differential equations governing linear (i.e., infinitesimal deformation) seismic wave propagation within a three-dimensional isotropic elastic body The medium is characterized by the three parameters: compressional (P) wave speed, shear (S) wave speed, and mass density, all of which may vary in the three spatial dimensions. The nine dependent variables (three particle velocity vector components and six stress tensor components) are stored within the algorithm on staggered spatial and temporal grids. The 3D spatial grid is rectangular, and grid intervals are uniform in each coordinate direction. Numerical solution methodology consists of explicit, time-domain, finite-differencing. Discrete finite-difference (FD) operators approximating partial derivatives possess 2nd-order accuracy in time and 4th-order accuracy in space. FD formulae for updating the wavefield variables are appropriately non-dimensionalized and normalized so that single-precision arithmetic calculations yield 1105824/01 adequate accuracy. This software will be used to generate seismic responses for typical geological/geophysical models of interest in the petroleum, mining, geotechnical, geothermal, hydrological, environmental assessment, and underground storage industries. Additionally, US government agencies (including the military) involved in monitoring of explosions or remote surveillance of underground facilities.

Aldridge, David F↗

Implementation of a pressure correction term in the CTF sub-channel code

CTF [1] is a modernized and improved version of the legacy subchannel code, COBRA-TF [2], that is being jointly developed and maintained by Oak Ridge National Laboratory (ORNL) and North Carolina State University. The code was adopted by ORNL for use in the Consortium for Advanced Simulation of Light Water Reactors (CASL) in 2012 for aiding in addressing CASL challenge problems. Since that time, activities related to CTF have included implementing software quality assurance measures, implementing new features and models, performing validation and verification testing, establishing and supporting a CTF User Group, and developing the code for use in coupled applications [3, 4, 5]. CTF is applicable to single- and two-phase flows in light water reactor geometries at normal and accident operating conditions. The two-phase flow model consists of the six-equation two-phase flow model [6] augmented by equations for the droplet field and also includes appropriate source terms. This work focuses on the numerical stability of the six-equation two-phase flow model and is part of a recent eort to improve CTF capabilities for simulating flows in boiling nuclear reactors (BWRs). As it is of common knowledge among the thermodynamic community, the six-equation two-phase flow model is not strongly hyperbolic, meaning some of its eigenvalues are either not real or not distinct [7]. In a Cauchy sense and for an initial-value problem, strong hyperbolicity was found to be equivalent to well-posedness which ensures uniqueness of the solution in the space-time used. This concept is also of importance when designing high-order numerical methods and also when implementing boundary conditions that rely on real eigenvalues such as Riemann solvers. A tremendous amount of research is available in the literature on how to hyperbolize the six-equation two-phase flow model by adding ad hoc terms to the system of equations often referred to as virtual mass or interfacial pressure correction term. From a mathematical prospective, the main idea driving this approach is to add terms to the phasic momentum equation containing first-order partial derivatives of the unknowns to modify the Jacobian matrix and thus canceling the imaginary part of the eigenvalues.For this work it was chosen to implement a interfacial pressure correction (IPC) term on the same model as what was done for the CATHARE system code [8], that allows to recover a two-pressure formulation. In the following, the six-equation two-phase flow model is recalled along with the IPC term and its influence on the eigenvalues. Then, numerical results and convergence studies are presented for a water-faucet problem [9] at a pressure of 10 bar. Finally, conclusions and future work are addressed.

Delchini, Marco↗

Implementation of a Pressure Correction Term in the CTF Subchannel Code

CTF is a modernized and improved version of the legacy subchannel code COBRA-TF, being jointly developed and maintained by Oak Ridge National Laboratory (ORNL) and North Carolina State University. The code was adopted by ORNL for use in the Consortium for Advanced Simulation of Light Water Reactors (CASL) in 2012 to help address CASL challenge problems. Since that time, activities related to CTF have included implementing software quality assurance measures, implementing new features and models, performing validation and verification testing, establishing and supporting a CTF user group, and developing the code for use in coupled applications. CTF is applicable to single- and two-phase flows in light water reactor geometries at normal and accident operating conditions. The two-phase flow model consists of the six-equation two-phase flow model augmented by equations for the droplet field, and it also includes appropriate source terms. This work focuses on the numerical stability of the six-equation two-phase flow model and is part of a recent effort to improve CTF capabilities for simulating flows in boiling water reactors (BWRs). The six-equation two-phase flow model is not strongly hyperbolic, meaning that some of its eigenvalues are either not real or not distinct. In a Cauchy sense, and for an initial-value problem, strong hyperbolicity was found to be equivalent to well-posedness, which ensures the uniqueness of the solution in the space-time used. This concept is also of importance when designing high-order numerical methods and also when implementing boundary conditions that rely on real eigenvalues such as Riemann solvers. A tremendous amount of research is available in the literature on how to hyperbolize the six-equation two-phase flow model by adding ad hoc terms to the system of equations. Such terms are often referred to as virtual mass or interfacial pressure correction terms. From a mathematical perspective, this approach adds terms to the phasic momentum equation containing first-order partial derivatives of the unknowns to modify the Jacobian matrix, thus the imaginary part of the eigenvalues. For this work, an interfacial pressure correction (IPC) term on the same model as what was used for the CATHARE system code, is implemented in CTF. This allows for recovery of a two-pressure formulation. In the following, the six-equation two-phase flow model is recalled, along with the IPC term and its influence on the eigenvalues. Then, numerical results and convergence studies are presented for a water-faucet problem at a pressure of 10 bar. Finally, conclusions and future work are addressed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗