Results for “plume flow” — Page 18

NASA NTRSDate not supplied

Validation of Artemis I Aerothermal Design Models Using Developmental Flight Instrumentation

The inaugural flight of the Space Launch System (SLS) Block 1 launch vehicle, Artemis I, occurred on November 16, 2022, and featured a full suite of Developmental Flight Instrumentation (DFI) that provided aerothermodynamic measurements to assess thermal design and substantiate aerothermodynamic models. The Block 1 launch vehicle aerothermal instrumentation consisted of approximately 277 aerothermal gauges mounted throughout the Orion Multi-Purpose Crew Vehicle (MPCV), Integrated Spacecraft and Payload Element (ISPE), Core Stage (CS) and Solid Rocket Boosters (SRB) and an additional 179 thermal gauges on the Orion Crew Module (CM). Instrumentation included calorimeters, radiometers, pressure transducers, gas temperature probes, and thermocouples. Data was collected from lift-off through CS Main Engine Cut-Off (MECO). The flight data was invaluable for determining aerothermal model performance and developing flight-derived aerothermal environments for flight reconstruction thermal analysis and future SLS aerothermal models. The data offered critical insights into the aerothermodynamic conditions experienced during the launch and ascent of the SLS vehicle. This study compares the flight derived environments to pre-existing design models. The aerothermal models were constructed using MINIVER, the aerothermal engineering code which predicts aerodynamic heating and acts as an integration tool for incorporating databases from computational fluid dynamics (CFD) simulations and wind tunnel test data. The comparisons reveal the fidelity of the design models, highlighting areas where the design models accurately predicted flight conditions and instances where deviations were observed. Preliminary results suggest that while the design models largely aligned with the observed flight data, there were unique observations that reflected needed areas of model refinement. Aerothermal flight data from Artemis I for the SLS Block 1 vehicle will be further utilized to enhance the accuracy of Block 1B and Block 2 aerothermal models, ensuring improved safety and performance for subsequent Artemis missions.

aerothermodynamics↗

NASA NTRSDate not supplied

Validation of Artemis I Aerothermal Design Models Using Developmental Flight Instrumentation

The inaugural flight of the Space Launch System (SLS) Block 1 launch vehicle, Artemis I, occurred on November 16, 2022, and featured a full suite of Developmental Flight Instrumentation (DFI) that provided aerothermodynamic measurements to assess thermal design and substantiate aerothermodynamic models. The Block 1 launch vehicle aerothermal instrumentation consisted of approximately 277 aerothermal gauges mounted throughout the Orion Multi-Purpose Crew Vehicle (MPCV), Integrated Spacecraft and Payload Element (ISPE), Core Stage (CS) and Solid Rocket Boosters (SRB) and an additional 179 thermal gauges on the Orion Crew Module (CM). Instrumentation included calorimeters, radiometers, pressure transducers, gas temperature probes, and thermocouples. Data was collected from lift-off through CS Main Engine Cut-Off (MECO). The flight data was invaluable for determining aerothermal model performance and developing flight-derived aerothermal environments for flight reconstruction thermal analysis and future SLS aerothermal models. The data offered critical insights into the aerothermodynamic conditions experienced during the launch and ascent of the SLS vehicle. This study compares the flight derived environments to pre-existing design models. The aerothermal models were constructed using MINIVER, the aerothermal engineering code which predicts aerodynamic heating and acts as an integration tool for incorporating databases from computational fluid dynamics (CFD) simulations and wind tunnel test data. The comparisons reveal the fidelity of the design models, highlighting areas where the design models accurately predicted flight conditions and instances where deviations were observed. Preliminary results suggest that while the design models largely aligned with the observed flight data, there were unique observations that reflected needed areas of model refinement. Aerothermal flight data from Artemis I for the SLS Block 1 vehicle will be further utilized to enhance the accuracy of Block 1B and Block 2 aerothermal models, ensuring improved safety and performance for subsequent Artemis missions.

aerothermodynamics↗

NASA NTRSDate not supplied

NASA Space Launch System Artemis I & II Post Flight Ascent Aerothermal Environments Overview

Since 2011 the Aerosciences Branch/EV33 at NASA Marshall Space Flight Center has been involved with the development of ascent external aerothermal environments for the NASA Space Launch System (SLS) Block 1 launch vehicle for the purposes of supporting thermal analysis and the design of thermal protection systems. The SLS Block 1 Artemis I and II launch vehicles successfully launched from Pad39B at NASA Kennedy Space Center on November 16th, 2022 and April 1st, 2026, respectively. Over 70 aerothermal islands, consisting of over 265 operational instruments captured aerodynamic heating and plume induced environments throughout the launch vehicles. Gauges consisted of calorimeters, radiometers, gas temperature probes, pressure transducers, bi-directional pressure probes and thermocouples. Prior to launch, aerothermal design environment models were generated to predict ascent aerodynamic heating and plume induced environments over a design space that covered a range of vehicle trajectories that varied atmospheric, vehicle performance, and off-nominal, engine-out conditions. Post flight reconstruction models were developed for each flight island using the Day-of-Launch (DOL) Best Equivalent Trajectory (BET) that provided freestream conditions and propulsion system boundary conditions. This paper discusses a summary of the ascent aerothermal environments observed during the flights and the respective modelling approaches and the performance of them through comparisons of flight data and predictions.

aerothermodynamics↗

NASA NTRS1973

Estuarine and coastal water dynamics controlling sediment movement and plume development in Long Island Sound

The author has identified the following significant results. As the Connecticut River flows into Long Island Sound, large plumes develop during the mixing of ocean and estuarine waters. Plumes were delineated for July 28, October 8, October 27, and December 2, 1972, by analyzing ERTS-1 imagery with the SRI Electronic Satellite Image Analysis Console (ESIAC). Because the chemical and physical composition of the plume and ocean water were not too different, the ESIAC was utilized to expand the scenes and subject the transparencies to varying combinations of viewing techniques to identify and delineate the plumes. Best results were obtained when band 5 transparencies were used. Indications are, when the scene being analyzed is predominantly in the first two steps of the gray scale, it is best to use the negative transparencies. When the analysis is being done above the first two steps of the gray scale, it is best to use the positive transparencies.

Ruggles, F. H., Jr.↗

NASA NTRS1991

Four dimensional reconstruction and analysis of plume images

Results of a time-history based three-dimensional reconstruction of cross-sectional images corresponding to a specific planar location of the jet structure are reported. The experimental set-up is described, and three-dimensional displays of time-history based reconstruction of the jet structure are presented. Future developments in image analysis, quantification and interpretation, and flow visualization of rocket engine plume images are expected to provide a tool for correlating engine diagnostic features with visible flow structures.

Dhawan, Atam P.↗

NASA NTRS1975

Hydrazine engine plume contamination mapping

Instrumentation for the measurement of plume exhaust specie deposition rates were developed and demonstrated. The instruments, two sets of quartz crystal microbalances, were designed for low temperature operation in the back flow and variable temperature operation in the core flow regions of an exhaust plume. These quartz crystal microbalances performed nominally, and measurements of exhaust specie deposition rates for 8400 number of pulses for a 0.1-lb monopropellant thruster are reported.

Chirivella, J. E.↗

NASA NTRS1989

Investigation of a liquid-fed water resistojet plume

Measurements of mass flux and flow angle were taken throughout the forward flow region of the exhaust of a liquid-fed water resistojet using a quartz crystal microbalance (QCM). The resistojet operated at a mass flow rate of 0.1 g/s with a power input of 330 Watts. Measured values were compared to theoretical predictions obtained by employing a source flow approximation. Excellent agreement between predicted and measured mass flux values was attained; however, this agreement was highly dependent on knowledge of nozzle flow conditions. Measurements of the temperature at which the exhaust condensed on the QCM were obtained as a function of incident mass flux.

Manzella, D. H.↗

NASA NTRS1989

Investigation of a liquid-fed water resistojet plume

Measurements of mass flux and flow angle were taken throughout the forward flow region of the exhaust of a liquid-fed water resistojet using a quartz crystal microbalance (QCM). The resistojet operated at a mass flow rate of 0.1 g/s with a power input of 330 Watts. Measured values were compared to theoretical predictions obtained by employing a source flow approximation. Excellent agreement between predicted and measured mass flux values was attained; however, this agreement was highly dependent on knowledge of nozzle flow conditions. Measurements of the temperature at which the exhaust condensed on the QCM were obtained as a function of incident mass flux.

Manzella, D. H.↗

NASA NTRS1990

Evaluation of water cooled supersonic temperature and pressure probes for application to 1366 K flows

Water cooled supersonic probes are developed to investigate total pressure, static pressure, and total temperature in high-temperature jet plumes and thereby determine the mean flow properties. Two probe concepts, designed for operation at up to 1366 K in a Mach 2 flow, are tested on a water cooled nozzle. The two probe designs - the unsymmetric four-tube cooling configuration and the symmetric annular cooling design - take measurements at 755, 1089, and 1366 K of the three parameters. The cooled total and static pressure readings are found to agree with previous test results with uncooled configurations. The total-temperature probe, however, is affected by the introduction of water coolant, and effect which is explained by the increased heat transfer across the thermocouple-bead surface. Further investigation of the effect of coolant on the temperature probe is proposed to mitigate the effect and calculate more accurate temperatures in jet plumes.

Lagen, Nicholas↗

NASA NTRS1975

Dynamics of turbidity plumes in Lake Ontario

The author has identified the following significant results. Large turbidity features along the 275 km south shore of Lake Ontario were analyzed using LANDSAT-1 images. The Niagara River plume, ranging from 30 to 500 sq km in area is, by far, the largest turbidity feature in the lake. Based on image tonal comparisons, turbidity in the Welland Canal is usually higher than that in any other water course discharging into the lake during the shipping season. Less turbid water enters the lake from the Port Dalhousie diversion channel and the Genesee River. Relatively clear water resulting from the deposition of suspended matter in numerous upstream lakes is discharged by the Niagara and Oswego Rivers. Plume analysis corroborates the presence of a prevailing eastward flowing longshore current along the entire south shore. Plumes resulting from beach erosion were detected in the images. Extensive areas of the south shore are subject to erosion but the most severely affected beaches are situated between Fifty Mile Point, Ontario and Thirty Mile Point, New York along the Rochester embayment, and between Sodus Bay and Nine Mile Point.

Pluhowski, E. J.↗

NASA NTRS2009

Broadband Shock Noise in Internally-Mixed Dual-Stream Jets

Broadband shock noise (BBSN) has been studied in some detail in single-flow jets and recently in dual-stream jets with separate flow exhaust systems. Shock noise is of great concern in these latter cases because of the noise created for the aircraft cabin by the underexpanded nozzle flow at cruise. Another case where shock noise is of concern is in the case of future supersonic aircraft that are expected to have bypass ratios small enough to justify internally mixed exhaust systems, and whose mission will push cycles to the point of imperfectly expanded flows. Dual-stream jets with internally mixed plume have some simplifying aspects relative to the separate flow jets, having a single shock structure given by the common nozzle pressure. This is used to separate the contribution of the turbulent shear layer to the broadband shock noise. Shock structure is held constant while the geometry and strength of the inner and merged shear layers are varying by changing splitter area ratio and core stream temperature. Flow and noise measurements are presented which document the efforts at separating the contribution of the inner shear layer to the broadband shock noise.

Bridges, James E.↗

NASA NTRS1983

Aerodynamic analysis of the loft anomaly observed on orbital flight tests of the space shuttle

The loft anomaly observed during the launch phase of the orbital flight tests (OFT) of the Space Shuttle is described and evidence that the loft anomaly resulted from previously unobserved aerodynamic phenomena is presented. The anomaly was that the altitude at staging was higher than anticipated. The anticipated altitude profile was predicted on wind tunnel test results that did not accurately simulate the flow between the orbiter vehicle and external tank and did not adequately simulate the engine plumes and thus the base pressures. An analogy is used to relate the flow between the orbiter and external tank to the flow in a two dimensional channel. Plume simulation is identified as a major goal during wind tunnel testing, and a wind tunnel test that was conducted to provide the best possible representation of the plume effect on the channel flow field is described.

Surber, T. E.↗

NASA NTRS1967

Computer program uses characteristics method for free-jet investigation

Computer program computes the free-jet boundary contours and other flow properties within the exhaust plume from highly underexpanded nozzles operating in near-vacuum conditions. The calculations are made by the method of characteristics which makes use of three-dimensional irrotational equations of flow.

Craidon, C. B.↗

NASA NTRSDate not supplied

Seeding Mechanism for High-Pressure Nozzles

NASA tests new launch and entry vehicle configurations in wind tunnels, where flow visualizations and quantitative flow field measurements are often desired. Some of these vehicles have rocket motors for propulsion, retro-propulsion, or reaction control. Unseeded,high-pressure air is often used to simulate these rocket motor plumes. However, it is difficult to make off-body measurements in these regions, for several reasons. First, the plumes themselves are usually unseeded and at such low pressures that the flow velocity cannot currently be measured. Second, the plumes displace seeded tunnel air, preventing measurements such as laser sheet visualizations. Third, they force shock waves ahead of the vehicle, which melts the ice crystal fog commonly used for many visualization and measurement techniques. The Virginia Tech Advanced Propulsion and Power Lab has designed and tested a novel method for seeding the flow in these small-scale, high-pressure nozzles to allow quantitative measurement with a particle-based measurement such as particle image velocimetry (PIV). The method involves a Venturi contraction to draw the seed liquid out of a reservoir and into the nozzle channel, wherein shearing forces atomize the seed into particles. The concept was tested with a laser sheet visualization, which showed the nozzle spray pattern and the controllability of the seeding flow rate. This relatively inexpensive and simple technique may prove useful in wind tunnel experiments involving particle-based laser diagnostics and small, high-pressure nozzles.

particle image velocimetry↗

NASA NTRS1994

Numerical simulation of helicopter engine plume in forward flight

Flowfields around helicopters contain complex flow features such as large separated flow regions, vortices, shear layers, blown and suction surfaces and an inherently unsteady flow imposed by the rotor system. Another complicated feature of helicopters is their infrared signature. Typically, the aircraft's exhaust plume interacts with the rotor downwash, the fuselage's complicated flowfield, and the fuselage itself giving each aircraft a unique IR signature at given flight conditions. The goal of this project was to compute the flow about a realistic helicopter fuselage including the interaction of the engine air intakes and exhaust plume. The computations solve the Think-Layer Navier Stokes equations using overset type grids and in particular use the OVERFLOW code by Buning of NASA Ames. During this three month effort, an existing grid system of the Comanche Helicopter was to be modified to include the engine inlet and the hot engine exhaust. The engine exhaust was to be modeled as hot air exhaust. However, considerable changes in the fuselage geometry required a complete regriding of the surface and volume grids. The engine plume computations have been delayed to future efforts. The results of the current work consists of a complete regeneration of the surface and volume grids of the most recent Comanche fuselage along with a flowfield computation.

Dimanlig, Arsenio C. B.↗

NASA NTRS1994

Simulation of Low-density Nozzle Plumes in Non-zero Ambient Pressures

The direct simulation Monte-Carlo (DSMC) method was applied to the analysis of low-density nitrogen plumes exhausting from a small converging-diverging nozzle into finite ambient pressures. Two cases were considered that simulated actual test conditions in a vacuum facility. The numerical simulations readily captured the complicated flow structure of the overexpanded plumes adjusting to the finite ambient pressures, including Mach disks and barrel shaped shocks. The numerical simulations compared well to experimental data of Rothe.

Chung, Chan-Hong↗

NASA NTRS1976

A study of a plume induced separation shock wave, including effects of periodic plume unsteadiness

A wind tunnel investigation was conducted to study the flow field in which separation is caused by an expanding plume, with emphasis on effects associated with periodic unsteadiness in the plume. The separation shock was photographed with high speed motion pictures, from which mean shock position and excursion data were reported. Pressure fluctuations were measured beneath the separation shock. A response of the separation shock to plume periodic unsteadiness was identified, and the magnitude of a corresponding transfer function was defined. Small harmonic effects in plume response to periodic unsteadiness were noted. The stabilizing effect of a lateral surface protuberance near the separation shock wave was investigated. The protuberance configuration was a lateral circular cylinder, and various diameters, all less than the boundary layer thickness, were employed.

Doughty, J. O.↗

NASA NTRS2021

Twenty Years of NASA-EOS Multi-Sensor Satellite Observations at Kīlauea Volcano (2000–2019)

Recent eruptions of Kīlauea volcano, on the Island of Hawai'i, represent an ideal test location for studying volcanic plumes, due to its remote location and minimal anthropogenic pollution. Within this work we exploit the over 20-year data record from NASA EOS satellites to investigate the degree to which space-borne observations can detect shifts in known eruption dynamics at Kīlauea. Through the combined analysis of remotely sensed plume heights, plume particle microphysical properties, lava flow thermal tracking and high resolution SO2 mapping, we provide interpretations of the satellite signals in a volcanic context and link them to ground-based eruption reports for validation. We establish common patterns of plume dispersion and particle evolution and identify when significant shifts in activity occur. We also determine where ambient conditions influence the output retrieved from the space-borne sensors. By comparing the inferences derived from remote-sensing with the extensive record of suborbital observations at Kīlauea, we assess the strengths and limitations of the satellite-based volcanic assessment techniques. The work presented here highlights the capabilities of these techniques, allowing us to more confidently interpret volcanic activity observed from space globally, particularly in cases where ground observations are limited or entirely lacking.

volcano remote sensing↗