Search NASA⌕ Search

SEARCH · Search NASA

Results for “polyurethanes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Compatibility Assessment of Fuel System Elastomers with Bio-oil and Diesel Fuel

Bio-oil derived via fast pyrolysis is being developed as a renewable fuel option for petroleum distillates. The compatibility of neat bio-oil with six elastomer types was evaluated against the elastomer performance in neat diesel fuel, which served as the baseline. The elastomers included two fluorocarbons, six acrylonitrile butadiene rubbers (NBRs), and one type each of fluorosilicone, silicone, styrene butadiene rubber (SBR), polyurethane, and neoprene. Specimens of each material were exposed to the liquid and gaseous phases of the test fuels for 4 weeks at 60 degrees C, and properties in the wetted and dried states were measured. Exposure to bio-oil produced significant volume expansion in the fluorocarbons, NBRs, and fluorosilicone; however, excessive swelling (over 80%) was only observed for the two fluorocarbons and two NBR grades. The polyurethane specimens were completely degraded by the bio-oil. In contrast, both silicone and SBR exhibited lower swelling levels in bio-oil compared to neat diesel fuel. The implication is that, while polyurethane and fluorocarbon may not be acceptable seal materials for bio-oils, silicone may offer a lower cost alternative.

09 BIOMASS FUELS↗

Adhesion Capabilities of Permanent Foaming Fixatives for Deactivation and Decommissioning Activities - 20308

Florida International University's Applied Research Center and the Department of Energy's Savannah River National Laboratory are examining various mechanical properties of intumescent rigid polyurethane foams in order to be used as a permanent foaming fixative. Intumescent polyurethane foams are favored more than non-intumescent polyurethane foams due to their ability to mitigate flame and smoke propagation when exposed to a fire. As a consequence, this ability, known as intumescing, will allow fire personnel ample time to arrive at a scene. Due to sites being dormant for many decades before the final decontamination stages, the likelihood of a fire remains high. Adhesion properties will ensure quality immobilization performance. The analysis consisted of evaluating tensile adhesion strengths on a variety of commercial-off-the-shelf polyurethane (PU) foams. The foams consisted of intumescent and a combination of flexible and rigid foams. The goal was to down select the rigid foams out of the group in terms of tensile adhesion performance. The ensuing analysis was to conduct shear adhesion testing on the rigid foams in an operational volume with one of the rigid foams being intumescent. This approach helped down select the intumescent rigid foam in an adhesion and operational sense. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A COMPARISON OF TWO THERMAL INSULATION AND STRUCTURAL MATERIALS FOR USE IN TYPE B PACKAGINGS

This paper presents the summary of design features and test results of two Type B Shipping Package prototype configurations comprising different insulating materials developed by the Savannah River National Laboratory (SRNL) for the Department of Energy. The materials evaluated, a closed-cell polyurethane foam and a vacuformed ceramic fiber material, were selected to provide adequate structural protection to the package containment vessel during Normal Conditions of Transport (NCT) and Hypothetical Accident Condition (HAC) events and to provide thermal protection during the HAC fire. Polyurethane foam has been used in shipping package designs for many years because of the stiffness it provides to the structure and because of the thermal protection it provides during fire scenarios. This comparison describes how ceramic fiber material offers an alternative to the polyurethane foam in a specific overpack design. Because of the high operating temperature ({approx}2,300 F) of the ceramic material, it allows for contents with higher heat loads to be shipped than is possible with polyurethane foam. Methods of manufacturing and design considerations using the two materials will be addressed.

36 MATERIALS SCIENCE↗

Flexible Foam Model.

Experiments were performed to characterize the mechanical response of a 15 pcf flexible polyurethane foam to large deformation at different strain rates and temperatures. Results from these experiments indicated that at room temperature, flexible polyurethane foams exhibit significant nonlinear elastic deformation and nearly return to their original undeformed shape when unloaded. However, when these foams are cooled to temperatures below their glass transition temperature of approximately -35 o C, they behave like rigid polyurethane foams and exhibit significant permanent deformation when compressed. Thus, a new model which captures this dramatic change in behavior with temperature was developed and implemented into SIERRA with the name Flex_Foam to describe the mechanical response of both flexible and rigid foams to large deformation at a variety of temperatures and strain rates. This report includes a description of recent experiments. Next, development of the Flex Foam model for flexible polyurethane and other flexible foams is described. Selection of material parameters are discussed and finite element simulations with the new Flex Foam model are compared with experimental results to show behavior that can be captured with this new model.

36 MATERIALS SCIENCE↗

Modeling Shock-Driven Reaction in Low-Density Non-energetic polymeric materials

Shock experiments on low density polyurethane foams reveal evidence of reaction at low impact pressures. However, these reaction thresholds are not evident over the low pressures reported for historical Hugoniot data of highly distended polyurethane at densities below 0.1 g/cc. To fill this gap, impact data for PMDI foam with a density of 0.087 g/cc were acquired for model validation. An equation of state (EOS) was developed to predict the shock response of these highly distended materials over the full range of impact conditions representing compaction of the inert material, low-pressure decomposition, and compression of the reaction products. A tabular SESAME EOS of the reaction products was generated using the JCZS database in the TIGER equilibrium code. In particular, the Arrhenius Burn EOS, a two-state model which transitions from an unreacted to a reacted state using Arrhenius kinetics, as implemented in the shock physics code CTH, was modified to include a statistical distribution of states. Hence, a single EOS is presented that predicts the onset to reaction due to shock loading in PMDI-based polyurethane foams. This methodology was also used to predict the anomalous compaction of PMDI foams over published data sets from 0.087 to 0.87 g/cc, and solid Polyurethane at a theoretical maximum density (TMD) of 1.264 g/cc. Likewise, similar modeling techniques were used to predict the performance of SX-358 foam, an RTV-based stress cushion material at a nominal density of 0.41 g/cc, and the matrix material, with properties similar to Sylgard, at 1.1 g/cc. At the start of this study, data were only available at a single impact condition below the threshold for reaction; hence, the decomposition of this material at higher pressures was revealed as a significant finding of this work. The decomposition of SX-358 at higher impact pressures to product species including solid, liquid, and gaseous molecules was estimated with thermochemical equilibrium calculations using TIGER. with thermochemical equilibrium calculations using TIGER. This modeling approach, developed for PMDI foam, was shown to predict gas gun data, acquired as part of this study, up to pressures of 14 GPa. Furthermore, additional phase transitions were predicted in the product species under shock compression. To date, this study is the first known to the authors that demonstrates and successfully predicts the decomposition of these low-density polymer-based foams using a single model applicable to a broad range of impact loading conditions.

36 MATERIALS SCIENCE↗

Polymers depolymerizable by metathesis of a cleavable unit

Novel polymers are depolymerizable by metathesis of a cleavable unit. As an example, a series of linear and crosslinked polyurethanes were prepared that can be selectively depolymerized under mild conditions. Two unique polyols were synthesized bearing unsaturated units in a configuration designed to favor ring-closing metathesis to five- and six-membered cycloalkenes. These polyols were co-polymerized with toluene diisocyanate to generate linear polyurethanes and trifunctional hexamethylene- and diphenylmethane-based isocyanates to generate crosslinked polyurethanes. The polyol design is such that the ring-closing metathesis reaction cleaves the backbone of the polymer chain. Upon exposure to dilute solutions of Grubbs' catalyst under ambient conditions, the polyurethanes were rapidly depolymerized to low molecular weight, soluble products bearing vinyl and cycloalkene functionalities. These functionalities enabled further re-polymerization by traditional strategies for polymerization of double bonds. This general approach can be expanded to develop a range of chemically recyclable condensation polymers that are readily depolymerized by orthogonal metathesis chemistry.

Jones, Brad Howard↗

A Processable Shape Memory Polymer System for Biomedical Applications

Polyurethane shape memory polymers (SMPs) with tunable thermomechanical properties and advanced processing capabilities are synthesized, characterized, and implemented in the design of a microactuator medical device prototype. The ability to manipulate glass transition temperature ( T g ) and crosslink density in low-molecular weight aliphatic thermoplastic polyurethane SMPs is demonstrated using a synthetic approach that employs UV catalyzed thiol-ene “click” reactions to achieve postpolymerization crosslinking. Polyurethanes containing varying C=C functionalization are synthesized, solution blended with polythiol crosslinking agents and photoinitiator and subjected to UV irradiation, and the effects of number of synthetic parameters on crosslink density are reported. Thermomechanical properties are highly tunable, including glass transitions tailorable between 30 and 105 °C and rubbery moduli tailorable between 0.4 and 20 MPa. This new SMP system exhibits high toughness for many formulations, especially in the case of low crosslink density materials, for which toughness exceeds 90 MJ m –3 at select straining temperatures. To demonstrate the advanced processing capability and synthetic versatility of this new SMP system, a laser-actuated SMP microgripper device for minimally invasive delivery of endovascular devices is fabricated, shown to exhibit an average gripping force of 1.43 ± 0.37 N and successfully deployed in an in vitro experimental setup under simulated physiological conditions.

42 ENGINEERING↗

An Investigation of the Effect of Sintering Conditions on the Mechanical Behavior of Electroplated Nickel Foams

This study investigates the effect of sintering temperature on the compression strength of nickel foams in an inert atmosphere. The nickel foams were produced by the electrodeposition technique on polyurethane foam substrate. As-plated Ni foams were sintered at 873 K, 1073 K, and 1273 K (600 °C, 800 °C, and 1000 °C) in order to eliminate polyurethane and to enhance ductility at a controlled atmosphere. A compression test was used to determine the mechanical behavior. The morphology of produced foams was analyzed by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Quantitative EDS analysis implied that carbon diffuses into nickel structure during the polyurethane decomposition. The amount of carbon in nickel foam increases with heat treatment temperature. The results also reveal that the oxygen impurity arisen from polymer vapors can diffuse into the nickel structure at elevated sintering temperature [i.e., 1273 K (1000 °C)]. The compression curve of as-plated foam showed brittle behavior due to the electroplating condition. The sintering process in the neutral atmosphere could create ductile foams, although the strength of the foams decreases with an increase in the sintering temperature.

36 MATERIALS SCIENCE↗