Search NASA⌕ Search

SEARCH · Search NASA

Results for “selective dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

300 Area Uranium Stabilization Through Polyphosphate Injection: Final Report

The objective of the treatability test was to evaluate the efficacy of using polyphosphate injections to treat uranium-contaminated groundwater in situ. A test site consisting of an injection well and 15 monitoring wells was installed in the 300 Area near the process trenches that had previously received uranium-bearing effluents. This report summarizes the work on the polyphosphate injection project, including bench-scale laboratory studies, a field injection test, and the subsequent analysis and interpretation of the results. Previous laboratory tests have demonstrated that when a soluble form of polyphosphate is injected into uranium-bearing saturated porous media, immobilization of uranium occurs due to formation of an insoluble uranyl phosphate, autunite [Ca(UO2)2(PO4)2•nH2O]. These tests were conducted at conditions expected for the aquifer and used Hanford soils and groundwater containing very low concentrations of uranium (10-6 M). Because autunite sequesters uranium in the oxidized form U(VI) rather than forcing reduction to U(IV), the possibility of re-oxidation and subsequent re-mobilization is negated. Extensive testing demonstrated the very low solubility and slow dissolution kinetics of autunite. In addition to autunite, excess phosphorous may result in apatite mineral formation, which provides a long-term source of treatment capacity. Phosphate arrival response data indicate that, under site conditions, the polyphosphate amendment could be effectively distributed over a relatively large lateral extent, with wells located at a radial distance of 23 m (75 ft) reaching from between 40% and 60% of the injection concentration. Given these phosphate transport characteristics, direct treatment of uranium through the formation of uranyl-phosphate mineral phases (i.e., autunite) could likely be effectively implemented at full field scale. However, formation of calcium-phosphate mineral phases using the selected three-phase approach was problematic. Although amendment arrival response data indicate some degree of overlap between the reactive species and thus potential for the formation of calcium-phosphate mineral phases (i.e., apatite formation), the efficiency of this treatment approach was relatively poor. In general, uranium performance monitoring results support the hypothesis that limited long-term treatment capacity (i.e., apatite formation) was established during the injection test. Two separate overarching issues affect the efficacy of apatite remediation for uranium sequestration within the 300 Area: 1) the efficacy of apatite for sequestering uranium under the present geochemical and hydrodynamic conditions, and 2) the formation and emplacement of apatite via polyphosphate technology. In addition, the long-term stability of uranium sequestered via apatite is dependent on the chemical speciation of uranium, surface speciation of apatite, and the mechanism of retention, which is highly susceptible to dynamic geochemical conditions. It was expected that uranium sequestration in the presence of hydroxyapatite would occur by sorption and/or surface complexation until all surface sites have been depleted, but that the high carbonate concentrations in the 300 Area would act to inhibit the transformation of sorbed uranium to chernikovite and/or autunite. Adsorption of uranium by apatite was never considered a viable approach for in situ uranium sequestration in and of itself, because by definition, this is a reversible reaction. The efficacy of uranium sequestration by apatite assumes that the adsorbed uranium would subsequently convert to autunite, or other stable uranium phases. Because this appears to not be the case in the 300 Area aquifer, even in locations near the river, apatite may have limited efficacy for the retention and long-term immobilization of uranium at the 300 Area site..

54 ENVIRONMENTAL SCIENCES↗

Impact of Mineral Reactive Surface Area on Forecasting Geological Carbon Sequestration in a CO2-EOR Field

Mineral reactive surface area (RSA) is one of the key factors that control mineral reactions, as it describes how much mineral is accessible and can participate in reactions. This work aims to evaluate the impact of mineral RSA on numerical simulations for CO2 storage at depleted oil fields. The Farnsworth Unit (FWU) in northern Texas was chosen as a case study. A simplified model was used to screen representative cases from 87 RSA combinations to reduce the computational cost. Three selected cases with low, mid, and high RSA values were used for the FWU model. Results suggest that the impact of RSA values on CO2 mineral trapping is more complex than it is on individual reactions. While the low RSA case predicted negligible porosity change and an insignificant amount of CO2 mineral trapping for the FWU model, the mid and high RSA cases forecasted up to 1.19% and 5.04% of porosity reduction due to mineral reactions, and 2.46% and 9.44% of total CO2 trapped in minerals by the end of the 600-year simulation, respectively. The presence of hydrocarbons affects geochemical reactions and can lead to net CO2 mineral trapping, whereas mineral dissolution is forecasted when hydrocarbons are removed from the system.

58 GEOSCIENCES↗

Solid phase evolution in the Biosphere 2 hillslope experiment as predicted by modeling of hydrologic and geochemical fluxes

A reactive transport geochemical modeling study was conducted to help predict the mineral transformations occurring over a ten year time-scale that are expected to impact soil hydraulic properties in the Biosphere 2 (B2) synthetic hillslope experiment. The modeling sought to predict the rate and extent of weathering of a granular basalt (selected for hillslope construction) as a function of climatic drivers, and to assess the feedback effects of such weathering processes on the hydraulic properties of the hillslope. Flow vectors were imported from HYDRUS into a reactive transport code, CrunchFlow2007, which was then used to model mineral weathering coupled to reactive solute transport. Associated particle size evolution was translated into changes in saturated hydraulic conductivity using Rosetta software. We found that flow characteristics, including velocity and saturation, strongly influenced the predicted extent of incongruent mineral weathering and neo-phase precipitation on the hillslope. Results were also highly sensitive to specific surface areas of the soil media, consistent with surface reaction controls on dissolution. Effects of fluid flow on weathering resulted in significant differences in the prediction of soil particle size distributions, which should feedback to alter hillslope hydraulic conductivities.

54 ENVIRONMENTAL SCIENCES↗

DEMONSTRATION OF THE GLYCOLIC-FORMIC FLOWSHEET IN THE SRNL SHIELDED CELLS USING ACTUAL WASTE

Glycolic acid was effective at dissolving many metals, including iron, during processing with simulants. Criticality constraints take credit for the insolubility of iron during processing to prevent criticality of fissile materials. Testing with actual waste was needed to determine the extent of iron and fissile isotope dissolution during Chemical Process Cell (CPC) processing. The Alternate Reductant Project was initiated by the Savannah River Remediation (SRR) Company to explore options for the replacement of the nitric-formic flowsheet used for the CPC at the Defense Waste Processing Facility (DWPF). The goals of the Alternate Reductant Project are to reduce CPC cycle time, increase mass throughput of the facility, and reduce operational hazards. In order to achieve these goals, several different reductants were considered during initial evaluations conducted by Savannah River National Laboratory (SRNL). After review of the reductants by SRR, SRNL, and Energy Solutions (ES) Vitreous State Laboratory (VSL), two flowsheets were further developed in parallel. The two flowsheet options included a nitric-formic-glycolic flowsheet, and a nitric-formic-sugar flowsheet. As of July 2011, SRNL and ES/VSL have completed the initial flowsheet development work for the nitric-formic-glycolic flowsheet and nitric-formic-sugar flowsheet, respectively. On July 12th and July 13th, SRR conducted a Systems Engineering Evaluation (SEE) to down select the alternate reductant flowsheet. The SEE team selected the Formic-Glycolic Flowsheet for further development. Two risks were identified in SEE for expedited research. The first risk is related to iron and plutonium solubility during the CPC process with respect to criticality. Currently, DWPF credits iron as a poison for the fissile components of the sludge. Due to the high iron solubility observed during the flowsheet demonstrations with simulants, it was necessary to determine if the plutonium in the radioactive sludge slurry demonstrated the same behavior. The second risk is related to potential downstream impacts of glycolate on Tank Farm processes. The downstream impacts will be evaluated by a separate research team. Waste Solidification Engineering (WSE) has requested a radioactive demonstration of the Glycolic-Formic Flowsheet with radioactive sludge slurry be completed in the Shielded Cells Facility of the SRNL. The Shielded Cells demonstration only included a Sludge Receipt and Adjustment Tank (SRAT) cycle, and not a Slurry Mix Evaporator (SME) cycle or the co-processing of salt products. Sludge Batch 5 (SB5) slurry was used for the demonstration since it was readily available, had been previously characterized, and was generally representative of sludges being processing in DWPF. This sample was never used in the planned Shielded Cells Run 7 (SC-7).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Changes in rock matrix compressibility during deep CO 2 storage

Geologic carbon storage projects aim to permanently trap large volumes of CO 2 in reservoir rock sealed with low permeability layers. As high-pressure supercritical or liquid CO 2 is injected, hydromechanical and chemical processes caused by the reaction between the rock and acidic mixture of brine and CO 2 are initiated. The compressibility of reservoir rock needs to be properly characterized in order to assess the deformation and stability of the host formations, and there are a number of factors to be considered, including the matrix structure, solid, pores, and fluid. Here this study triggers from a fundamental question whether CO 2 treatment affects the compressibility of the rock matrix and its dominant composing solid minerals. Three different reservoir representatives are selected: Berea sandstone for silica-rich rock, and Apulian limestone and Indiana limestone for calcite-rich rock. Quartz and calcite are the main composing minerals of the reservoir rock, and their crystals are separately examined. Experimental methods are introduced for high-pressure CO 2 treatment of water-saturated materials, and measurements of the unjacketed and solid compressibilities are conducted. No change in the solid compressibility of the sandstone and quartz after CO 2 treatment is observed, whereas it increases by 18–21% for the limestones and by 15% for calcite. The latter observation is inconsistent with the ultrasonic wave velocities measurements and is believed to be due to the local dissolution of the calcite crystal surface. Our results show that only the solid matrix of the limestones becomes more compressible after CO 2 treatment. Consequent microimaging and mercury intrusion porosimetry analyses allowed observations of dissolution and precipitation of calcite, and creation of new connected and non-connected pores. Finally, the changes in limestone solid compressibilities and pore structure could significantly affect the rock properties and behavior during and after CO 2 injection and should be accounted for in the reservoir models.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Zinc Removal from Basic Oxygen Steelmaking Filter Cake by Leaching with Organic Acids

The dust generated from the basic oxygen steelmaking (BOS) process is a waste material mainly containing iron that cannot be recycled owing to its high zinc content. In this study, the leaching effects of different organic acids are compared, with the aim of determining an acid that selectively leaches and removes zinc from BOS dust, so that the waste material can be recycled into ironmaking and steelmaking processes in order to substitute part of the raw materials of steelmaking. The dust used in this study was scrubbed and collected in the form of a filter cake. The acids tested were oxalic, citric, acetic, propionic, butyric, and valeric acids. Butyric acid was found to be the most effective, with a high zinc extraction level of 49.7 pct and a low iron level of only 2.5 pct. Oxalic acid was the least effective leaching reagent for both zinc and iron extractions, owing to the formation of zinc and iron oxalate precipitates following metal dissolution. The filter cake and leached residues were characterized by chemical analysis, X-ray diffraction, X-ray photoelectron spectroscopy, and scanning electron microscopy with energy dispersive spectroscpopy.

36 MATERIALS SCIENCE↗

Simulation of Uranium(VI) Speciation and Sorption in Montmorillonite Clay in the Presence of Calcite Impurities

Montmorillonite is an abundant clay mineral that has been identified as the primary component in engineered bentonite barrier systems in future nuclear waste repositories. Selective sorption onto planar and edge surfaces of clay particles make it a great candidate for the attentuation of uranium(VI). Although previous works have investigated uranium(VI) interactions with this clay, few have done so in the presence of calcite, a mineral impurity in bentonite that is understood to alter U(VI) speciation, sorption, and consequently its mobility. PHREEQC software is used to simulate the chemical solution speciation of U(VI) under various known repository conditions, in the absence and presence of calcite, and across a range of U(VI)concentrations (1.0E-7 to 1.0E 5 M), and partial pressures of CO 2 (zero to 2% CO2) (Fig. 1). In addition, the kinetic dissolution of calcite is simulated to gain a better understanding of how quickly chemical equilibrium can be reached in these systems. Lastly, surface complexation models will be developed to characterize the influence of calcite impurities on the formation of ternary U(VI)-Ca-carbonate solution species on U(VI) sorption behavior. Our results indiciate that the presence of Ca 2+ and CO 3 2- ions released from calcite leads to U(VI)-Ca-carbonate species with a negative or neutral charge even without the presence of CO 2 . Quantification of these species will allow for the development of more accurate U(VI)-montmorillonite sorption models. Calcite precipitation at alkaline pH further complicates speciation by creating a competation for Ca 2+ . This research is being performed using funding received from the DOE Office of Nuclear Energy’s NEUP.

Pistorino, Jonathan C.↗

Austenitic Reversion of Cryo-rolled Ti-Stabilized Austenitic Stainless Steel: High-Resolution EBSD Investigation

In this study, AISI 321 austenitic stainless steel (ASS) was cryo-rolled and subsequently annealed at 650 and 800 °C to reverse BCC α′-martensite to FCC γ-austenite. The texture evolution associated with the reversion at the selected temperatures was investigated using high-resolution EBSD. After the reversion, TiC precipitates were observed to be more stable in 650 °C-annealed specimens than those reversed at 800 °C. {110} texture was mainly developed in specimens subjected to both annealing temperatures. However, specimens reversed at 650 °C have stronger texture than those annealed at 800 °C, even at the higher annealing time. The strong intensity of {110} texture component is attributed to the ability of AISI 321 ASS to memorize the crystallographic orientation of the deformed austenite, a phenomenon termed texture memory. The development of weaker texture in 800 °C-annealed specimens is attributed to the residual strain relief in grains, dissolution of grain boundary precipitates, and an increase in atomic migration along the grain boundaries. Based on the observed features of the reversed austenite grains and estimation from an existing model, it is suspected that the austenite reversion at 650 and 800 °C undergone diffusional and martensitic shear reversion, respectively.

36 MATERIALS SCIENCE↗

Transmission Geometry Laser Ablation into a Non-Contact Liquid Vortex Capture Probe for Mass Spectrometry Imaging

RATIONALE: Capture of material from a laser ablation plume into a continuous flow stream of solvent provides the means for uninterrupted sampling, transport and ionization of collected material for coupling with mass spectral analysis. Reported here is the use of vertically aligned transmission geometry laser ablation in combination with a new non-contact liquid vortex capture probe coupled with electrospray ionization for spot sampling and chemical imaging with mass spectrometry. Methods: A vertically aligned continuous flow liquid vortex capture probe was positioned directly underneath a sample surface in a transmission geometry laser ablation (355 nm, 10 Hz, 7 ns pulse width) setup to capture into solution the ablated material. The outlet of the vortex probe was coupled to the Turbo V ion source of an AB SCIEX TripleTOF 5600+ mass spectrometer. System operation and performance metrics were tested using inked patterns and thin tissue sections. Glass slides and slides designed especially for laser capture microdissection, viz., DIRECTOR slides and PEN 1.0 (polyethylene naphthalate) membrane slides, were used as sample substrates. Results: The estimated capture efficiency of laser ablated material was 24%, which was enabled by the use of a probe with large liquid surface area (~ 2.8 mm2) and with gravity to help direct ablated material vertically down towards the probe. The swirling vortex action of the liquid surface potentially enhanced capture and dissolution of not only particulates, but also gaseous products of the laser ablation. The use of DIRECTOR slides and PEN 1.0 (polyethylene naphthalate) membrane slides as sample substrates enabled effective ablation of a wide range of sample types (basic blue 7, polypropylene glycol, insulin and cyctochrome c) without photodamage using a UV laser. Imaging resolution of about 6 m was demonstrated for stamped ink on DIRECTOR slides based on the ability to distinguish features present both in the optical and in the chemical image. This imaging resolution was 20 times better than the previous best reported results with laser ablation/liquid sample capture mass spectrometry imaging. Using thin sections of brain tissue the chemical image of a selected lipid was obtained with an estimated imaging resolution of about 50 um. Conclusions: A vertically aligned, transmission geometry laser ablation liquid vortex capture probe, electrospray ionization mass spectrometry system provides an effective means for spatially resolved spot sampling and imaging with mass spectrometry.

DIRECTOR slides↗

2D Metal/Graphene and 2D Metal/Graphene/Metal Systems for Electrocatalytic Conversion of CO 2 to Formic Acid

Abstract Efficiently transforming CO 2 into renewable energy sources is crucial for decarbonization efforts. Formic acid (HCOOH) holds great promise as a hydrogen storage compound due to its high hydrogen density, non‐toxicity, and stability under ambient conditions. However, the electrochemical reduction of CO 2 (CO 2 RR) on conventional carbon black‐supported metal catalysts faces challenges such as low stability through dissolution and agglomeration, as well as suffering from high overpotentials and the necessity to overcome the competitive hydrogen evolution reaction (HER). In this study, we modify the physical/chemical properties of metal surfaces by depositing metal monolayers on graphene (M/G) to create highly active and stable electrocatalysts. Strong covalent bonding between graphene and metal is induced by the hybridization of sp and d orbitals, especially the sharp , , and orbitals of metals near the Fermi level, playing a decisive role. Moreover, charge polarization on graphene in M/G enables the deposition of another thin metallic film, forming metal/graphene/metal (M/G/M) structures. Finally, evaluating overpotentials required for CO 2 reduction to HCOOH, CO, and HER, we find that Pd/G, Pt/G/Ag, and Pt/G/Au exhibit excellent activity and selectivity toward HCOOH production. Our novel 2D hybrid catalyst design methodology may offer insights into enhanced electrochemical reactions through the electronic mixing of metal and other p‐block elements.

Cho, Jinwon↗

Ammonia-salt solvent promotes cellulosic biomass deconstruction under ambient pretreatment conditions to enable rapid soluble sugar production at ultra-low enzyme loadings

In this paper, we report a novel ammonia : ammonium salt solvent based pretreatment process that can rapidly dissolve crystalline cellulose into solution and eventually produce highly amorphous cellulose under near-ambient conditions. Pre-activating the cellulose I allomorph to its ammonia–cellulose swollen complex (or cellulose III allomorph) at ambient temperatures facilitated rapid dissolution of the pre-activated cellulose in the ammonia-salt solvent ( i.e. , ammonium thiocyanate salt dissolved in liquid ammonia) at ambient pressures. For the first time in reported literature, we used time-resolved in situ neutron scattering methods to characterize the cellulose polymorphs structural modification and understand the mechanism of crystalline cellulose dissolution into a ‘molecular’ solution in real-time using ammonia-salt solvents. We also used molecular dynamics simulations to provide insight into solvent interactions that non-covalently disrupted the cellulose hydrogen-bonding network and understand how such solvents are able to rapidly and fully dissolve pre-activated cellulose III. Importantly, the regenerated amorphous cellulose recovered after pretreatment was shown to require nearly ~50-fold lesser cellulolytic enzyme usage compared to native crystalline cellulose I allomorph for achieving near-complete hydrolytic conversion into soluble sugars. Lastly, we provide proof-of-concept results to further showcase how such ammonia-salt solvents can pretreat and fractionate lignocellulosic biomass like corn stover under ambient processing conditions, while selectively co-extracting ~80–85% of total lignin, to produce a highly digestible polysaccharide-enriched feedstock for biorefinery applications. Unlike conventional ammonia-based pretreatment processes ( e.g. , Ammonia Fiber Expansion or Extractive Ammonia pretreatments), the proposed ammonia-salt process can operate at near-ambient conditions to greatly reduce the pressure/temperature severity necessary for conducting effective ammonia-based pretreatments on lignocellulose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

PRELIMINARY FRIT DEVELOPMENT AND MELT RATE TESTING FOR SLUDGE BATCH 6 (SB6)

The Liquid Waste Organization (LWO) provided the Savannah River National Laboratory (SRNL) with a Sludge Batch 6 (SB6) composition projection in March 2009. Based on this projection, frit development efforts were undertaken to gain insight into compositional effects on the predicted and measured properties of the glass waste form and to gain insight into frit components that may lead to improved melt rate for SB6-like compositions. A series of Sludge Batch 6 (SB6) based glasses was selected, fabricated and characterized in this study to better understand the ability of frit compositions to accommodate uncertainty in the projected SB6 composition. Acceptable glasses (compositions where the Product Composition Control System (PCCS) Measurement Acceptability Region (MAR) predicted acceptable properties, good chemical durability was measured, and no detrimental nepheline crystallization was observed) can be made using Frit 418 with SB6 over a range of Na{sub 2}O and Al{sub 2}O{sub 3} concentrations. However, the ability to accommodate variation in the sludge composition limits the ability to utilize alternative frits for potential improvements in melt rate. Frit 535, which may offer improvements in melt rate due to its increased B2O3 concentration, produced acceptable glasses with the baseline SB6 composition at waste loadings of 34 and 42%. However, the PCCS MAR results showed that it is not as robust as Frit 418 in accommodating variation in the sludge composition. Preliminary melt rate testing was completed in the Melt Rate Furnace (MRF) with four candidate frits for SB6. These four frits were selected to evaluate the impacts of B{sub 2}O{sub 3} and Na{sub 2}O concentrations in the frit relative to those of Frit 418, although they are not necessarily candidates for SB6 vitrification. Higher concentrations of B{sub 2}O{sub 3} in the frit relative to that of Frit 418 appeared to improve melt rate. However, when a higher concentration of B{sub 2}O{sub 3} was coupled with a lower concentration of Na{sub 2}O relative to Frit 418, melt rate did not appear to improve. It is expected that a SB6 composition projection with less uncertainty will be received during analysis of the Tank 51 E-1 sample, which will be pulled after the completion of aluminum dissolution in August 2009. At that time, additional frit development work will be performed to seek improved melt rates while maintaining viable projected operating windows. This later work will ultimately lead to a frit recommendation for SB6.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2D Metal/Graphene and 2D Metal/Graphene/Metal Systems for Electrocatalytic Conversion of CO 2 to Formic Acid

Efficiently transforming CO 2 into renewable energy sources is crucial for decarbonization efforts. Formic acid (HCOOH) holds great promise as a hydrogen storage compound due to its high hydrogen density, non-toxicity, and stability under ambient conditions. However, the electrochemical reduction of CO 2 (CO 2 RR) on conventional carbon black-supported metal catalysts faces challenges such as low stability through dissolution and agglomeration, as well as suffering from high overpotentials and the necessity to overcome the competitive hydrogen evolution reaction (HER). In this study, we modify the physical/chemical properties of metal surfaces by depositing metal monolayers on graphene (M/G) to create highly active and stable electrocatalysts. Strong covalent bonding between graphene and metal is induced by the hybridization of sp and d orbitals, especially the sharp $d_{z^2}$, $d_{yz}$, $d_{xz}$ orbitals of metals near the Fermi level, playing a decisive role. Moreover, charge polarization on graphene in M/G enables the deposition of another thin metallic film, forming metal/graphene/metal (M/G/M) structures. Finally, evaluating overpotentials required for CO 2 reduction to HCOOH, CO, and HER, we find that Pd/G, Pt/G/Ag, and Pt/G/Au exhibit excellent activity and selectivity toward HCOOH production. Our novel 2D hybrid catalyst design methodology may offer insights into enhanced electrochemical reactions through the electronic mixing of metal and other p-block elements.

2D Electrocatalysts↗

Summary of research on the effect of LiNO{sub 3} on alkali-silica reaction in new concrete

This paper summarizes findings from a research study conducted at the University of New Brunswick in collaboration with the University of Texas at Austin, and CANMET-MTL, on the effect of LiNO{sub 3} on ASR in new concrete. The studies included expansion testing, silica dissolution measurements and microstructural examinations of cement systems containing glass and two different reactive aggregates (NB and NS). Only a small proportion of the data are presented here for the purpose of highlighting the principal findings of this investigation. Based on these findings, it is proposed that the inhibiting effect of LiNO{sub 3} against ASR in new concrete is attributed to the formation of two reaction products in the presence of lithium, these being a crystalline lithium silicate compound (Li{sub 2}SiO{sub 3}) crystal and a Li-bearing, low Ca silica gel. These two phases could serve as a diffusion barrier and protective layer to prevent the reactive silica from further attack by alkalis. It was found that the reason the two reactive aggregates selected responded differently to LiNO{sub 3} was due to the difference in their textural features. The NB aggregate contained reactive volcanic glass particles, the surface of which was immediately and equally available to sodium, potassium and lithium, and thus a Li-Si barrier was able to form quickly. The reactive phase in the NS aggregate was microcrystalline and strained quartz, which was embedded in a dense matrix of a non-reactive predominantly alumino-silicate phase and was not easily accessible to lithium.

36 MATERIALS SCIENCE↗

Gas nitriding behavior of refractory metals and implications for multi-principal element alloy design

Multi-principal element alloys (MPEAs) comprise a large, flexible compositional space that enables tuning of their chemistry, structure, and properties. Here, to facilitate the development of nitriding-based surface-enhancement strategies that harness a broad compositional space, this study examined the gas nitriding behavior of Hf, Mo, Nb, Ta, Ti, and Zr as a function of time, temperature (750 and 1000 °C), and nitriding potential (i.e. ammonia-to-hydrogen ratio). These metals were selected because they have a strong driving force to form nitrides, and appear in many promising refractory MPEA compositions. The nitriding temperatures were selected based on the phase transformation temperature of Ti and Zr, and the nitriding potentials were chosen such that all elements are expected to form nitrides. Mass gain measurements indicate that all six elements follow parabolic kinetics. The microstructure observations and quantitative microchemical analysis show formation of dense and well-adhered compound layers for Mo, Nb, and Ta. Thick diffusion zones appear in Hf, Ta, Ti, and Zr, and diffusion coefficients were fit to the composition profiles. Partial delamination of the compound layer occurred for Ti and Zr. Peak hardness values above 30 GPa are obtained in the dense compound layers, and the solute hardening of the underlying alloy is correlated with the nitrogen content. The results provide insight into the dynamics of nitride compound formation relative to interstitial dissolution of nitrogen, and are discussed in the context of MPEA composition and processing design.

36 MATERIALS SCIENCE↗

The Application of Differential Scanning Calorimetry to Investigate Precipitation Behavior in Nickel-Base Superalloys Under Continuous Cooling and Heating Conditions

In this study, a suite of experimental tools and fast-acting, numerical-simulation techniques was used to quantify the precipitation behavior of three nickel-base superalloys: IN-100, LSHR, and 718. Experimental methods comprised differential scanning calorimetry (DSC) to establish the specific heat as a function of temperature and selected direct-resistance heating trials (using a Gleeble ® machine) to obtain samples for microstructural analysis. For the DSC experiments, each alloy was cooled at a prescribed constant rate (between 5 and 20 K/min) after an initial soak/equilibration in the high-temperature, single-phase (supersolvus) temperature regime. On-heating DSC trials beginning at ambient temperature were also performed on alloy 718 in three different starting conditions: super- δ -solvus solution treated and water quenched (denoted as ST), solution treated and aged (STA), and solution treated and overaged (STOA). DSC results, revealing the thermal signatures associated with the kinetics of precipitation of γ ' (IN-100, LSHR) or γ ' and γ " (718), were interpreted using a previously-developed fast-acting routine that treats concurrent nucleation, growth, coarsening, and dissolution. For these simulations, special attention was paid to various thermo-kinetic input parameters including equilibrium solvus-approach curves, bulk free energies of transformation, matrix-precipitate interface energies, and effective diffusivities. For the γ - γ ' superalloys (IN-100 and LSHR), estimates of precipitate volume fraction as a function of temperature from the specific-heat data revealed semi-quantitative agreement with simulation predictions. For the γ - γ '- γ " superalloy (718), simulation predictions of precipitate volume fractions were converted to specific heat as a function of temperature and showed semi-quantitative agreement with the direct measurements.

36 MATERIALS SCIENCE↗

Effect of oxidation on the release of multiple metals from industrially polluted sediments and synchrotron-based evidence of Cu–S dynamic association

Disposal operations for industrially polluted sediments are usually accompanied by disturbance and resuspension, which can induce metal remobilization and secondary pollution. Evaluating the risk of metal release under various redox conditions is fundamental for predicting contaminant mobilization and guiding remediation measures. An abandoned oxidation pond, Yanjia Lake, China, was selected as a typical industrially polluted site. Re-suspension experiments were carried out by mixing polluted sediments with lake water under oxic or anoxic conditions, then investigating the effect of oxidation conditions on the release of multiple metals. Metal concentrations and aqueous chemistry in the overlying water were monitored. Synchrotron-based methods, including X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS), were used to characterize oxidation states and coordination conditions of metals in sediments. The release of metals, including Cr, Co, Ni, Cu, Zn, Se, Mo, Sn, Cd, and Pb, was enhanced under oxic vs. anoxic conditions. The XANES analysis revealed that elevated Cr and Zn concentrations under oxic conditions likely resulted from the oxidation of Cr(III) and oxidizing dissolution of ZnS, respectively. K-edge Cu XANES, S XANES, and Cu EXAFS analyses reconstructed the Cu–S association, indicating that S-related oxidation promoted Cu release and Cu–O partly replaced Cu–S in the sediment after a 7-day oxic treatment. The release of most metals was promoted under oxic conditions, resulting from the oxidation of sulfides and metals as indicated by aqueous and synchrotron-based evidence. The risk of secondary pollution is greatly enhanced under oxic conditions, which suggests that measures should be taken to minimize the redox disturbance during sediment remediation. This information can guide the management of sediments in Yanjia Lake and other contaminated sites with similar properties.

54 ENVIRONMENTAL SCIENCES↗