Search NASA⌕ Search

SEARCH · Search NASA

Results for “shock wave and boundary layer interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Unsteady separation in sharp fin-induced shock wave/turbulent boundary layer interaction at Mach 5

Fluctuating wall-pressure measurements are made in shock-wave/turbulent-boundary-layer interactions generated by sharp/unswept fins at angles of attack of 16, 18, 20, 22, 24, 26, and 28 degrees at Mach 5. The experiment was conducted under approximately adiabatic wall temperature conditions. The mean and rms pressure distributions can be collapsed in conical coordinates. The wall-pressure signal near separation is intermittent for all angles of attack (16-28 deg) and is qualitatively similar to that measured in unswept flows. However, the shock frequencies are higher - about 5 kHz compared to 0.5-1 kHz. Over the range of sweepbacks examined, from 25-55 deg, the spectral content of the fluctuating pressures does not change. Thus, the increase in separation-shock frequency from 1 to 5 kHz occurs at lower interaction sweepback and is not a continuous process with increasing sweepback. Power spectra at the position of maximum rms in the intermittent region for interactions in different incoming boundary layers have the same center frequency. The maximum rms in the intermittent region correlates with interaction sweepback, not with overall inviscid pressure rise.

Schmisseur, J. D.↗
NASA NTRS2013

Wind-US Code Contributions to the First AIAA Shock Boundary Layer Interaction Prediction Workshop

This report discusses the computations of a set of shock wave/turbulent boundary layer interaction (SWTBLI) test cases using the Wind-US code, as part of the 2010 American Institute of Aeronautics and Astronautics (AIAA) shock/boundary layer interaction workshop. The experiments involve supersonic flows in wind tunnels with a shock generator that directs an oblique shock wave toward the boundary layer along one of the walls of the wind tunnel. The Wind-US calculations utilized structured grid computations performed in Reynolds-averaged Navier-Stokes mode. Four turbulence models were investigated: the Spalart-Allmaras one-equation model, the Menter Baseline and Shear Stress Transport k-omega two-equation models, and an explicit algebraic stress k-omega formulation. Effects of grid resolution and upwinding scheme were also considered. The results from the CFD calculations are compared to particle image velocimetry (PIV) data from the experiments. As expected, turbulence model effects dominated the accuracy of the solutions with upwinding scheme selection indicating minimal effects.

Georgiadis, Nicholas J.↗
NASA NTRS1992

Experimental results for a hypersonic nozzle/afterbody flow field

The flow field created by the interaction of a single-expansion-ramp-nozzle (SERN) flow with a hypersonic external stream has been experimentally characterized using a generic nozzle/afterbody model in the 3.5-foot hypersonic wind tunnel of the NASA Ames Research Center. The presented results include oil-flow and shadowgraph flow visualization photographs, afterbody surface-pressure distributions, boundary layer rake measurements, and Preston-tube skin-friction measurements. The design, construction, and operation of the model was found to be successful. Surface oil-flow patterns show that the jet-plume flow attaches to the afterbody surface at jet pressure ratios between 154 and 234. The oil flow also shows the pattern of lines where the jet flow separates from the ramp, apparently as a result of interaction of the jet-plume internal shock wave with the ramp boundary layer.

Spaid, Frank W.↗
NASA NTRS1992

An experimental examination of the effects of incoming boundary layer modifications on the dynamics of a turbulent compression corner interaction

This experimental study examines the effects of modifications to the incoming turbulent boundary layer on the highly separated shock wave/boundary layer interaction generated by an unswept compression corner. Particular focus is placed on the motion of the unsteady separation shock wave. The flowfield was generated by a 28 deg ramp in a Mach 5 flow with a freestream Reynolds number of 50 x 10 exp 6/m. The incoming turbulent boundary layer transitioned naturally and developed under near-adiabatic wall conditions. Modification of the flow entering the interaction was effected through either a single plate boundary layer manipulator (BLM) or riblets. The BLM reduced the length of separation by 35-45 percent and reduced the streamwise extent of the separation shock motion by 36-74 percent. Examination of the flowfield downstream of the BLM showed this result to be due to the inviscid preturning of the flow by the BLM, and not by changes to the boundary layer dynamics. The riblets had no measurable effect on the compression corner interaction.

Mcclure, W. B.↗
NASA NTRS1988

Fluctuations and massive separation in three-dimensional shock-wave/boundary-layer interactions

Shock-wave unsteadiness was observed in rapidly compressed supersonic turbulent boundary layer flows with significant separation. A Mach 2.85 shock-wave/turbulent boundary layer flow was set up over a series of cylinder-flare bodies in the High Reynolds Number Channel 1. The transition from fully attached to fully separated flow was studied using axisymmetric flares with increasing compression angles. In the second phase, the 30 deg flare was inclined relative to the cylinder axis, so that the effect on a separated flow of increasing 3 dimensionality could be observed. Two 3-D separated cases are examined. A simple conditional sampling technique is applied to the data to group them according to an associated shock position. Mean velocities and turbulent kinetic energies, computed from the conditionally samples data, are compared to those from the unsorted data and to computed values. Three basic questions were addressed: can conditional sampling be used to provide snapshots of the flow; are averaged turbulence quantities dominated by the bimodal nature of the interaction; and is the shock unsteadiness really important to computational accuracy.

Kussoy, M. I.↗
NASA NTRS1988

Fluctuations and massive separation in three-dimensional shock-wave/boundary-layer interactions

Shock-wave unsteadiness was observed in rapidly compressed supersonic turbulent boundary layer flows with significant separation. A Mach 2.85 shock-wave/turbulent boundary layer flow was set up over a series of cylinder-flare bodies in the High Reynolds Number Channel 1. The transition from fully attached to fully separated flow was studied using axisymmetric flares with increasing compression angles. In the second phase, the 30-deg flare was inclined relative to the cylinder axis, so that the effect on a separated flow of increasing three-dimensionality could be observed. Two 3-D separated cases are examined. A simple conditional sampling technique is applied to the data to group them according to an associated shock position. Mean velocities and turbulent kinetic energies, computed from the conditionally sampled data, are compared to those from the unsorted data and to computed values. Three basic questions were addressed: can conditional sampling be used to provide snapshots of the flow; are averaged turbulence quantities dominated by the bimodal nature of the interaction; and is the shock unsteadiness really important to computational accuracy.

Kussoy, M. I.↗
NASA NTRS1992

Swept shock/boundary layer interaction experiments in support of CFD code validation

Research on the topic of shock wave/turbulent boundary-layer interaction was carried out during the past three years at the Penn State Gas Dynamics Laboratory. This report describes the experimental research program which provides basic knowledge and establishes new data on heat transfer in swept shock wave/boundary-layer interactions. An equilibrium turbulent boundary-layer on a flat plate is subjected to impingement by swept planar shock waves generated by a sharp fin. Five different interactions with fin angle ranging from 10 deg to 20 deg at freestream Mach numbers of 3.0 and 4.0 produce a variety of interaction strengths from weak to very strong. A foil heater generates a uniform heat flux over the flat plate surface, and miniature thin-film-resistance sensors mounted on it are used to measure the local surface temperature. The heat convection equation is then solved for the heat transfer distribution within an interaction, yielding a total uncertainty of about +/- 10 percent. These experimental data are compared with the results of numerical Navier-Stokes solutions which employ a k-epsilon turbulence model. Finally, a simplified form of the peak heat transfer correlation for fin interactions is suggested.

Settles, G. S.↗
NASA NTRS1995

Shock-Induced Separated Structures in Symmetric Corner Flows

Three-dimensional supersonic viscous laminar flows over symmetric corners are considered in this paper. The characteristic features of such configurations are discussed and an historical survey on the past research work is presented. A new contribution based on a numerical technique that solves the parabolized form of the Navier-Stokes equations is presented. Such a method makes it possible to obtain very detailed descriptions of the flowfield with relatively modest CPU time and memory storage requirements. The numerical approach is based on a space-marching technique, uses a finite volume discretization and an upwind flux-difference splitting scheme (developed for the steady flow equations) for the evaluation of the inviscid fluxes. Second order accuracy is reached following the guidelines of the ENO schemes. Different free-stream conditions and geometrical configurations are considered. Primary and secondary streamwise vortical structures embedded in the boundary layer and originated by the interaction of the latter with shock waves are detected and studied. Computed results are compared with experimental data taken from literature.

DAmbrosio, Domenic↗
NASA NTRS1992

Heat transfer measurements and CFD comparison of swept shock wave/boundary-layer interactions

An experimental research program providing basic knowledge and establishing new data on the heat transfer in swept shock wave/boundary-layer interactions is described. An equilibrium turbulent boundary-layer on a flat plate is subjected to impingement by swept planar shock waves generated by a sharp fin. Five different interactions with fin angles ranging from 10 to 20 deg at freestream Mach numbers of 3.0 and 4.0 produce a variety of interaction strengths from weak to very strong. A foil heater generates a uniform heat flux over the flat plate surface and miniature thin-film-resistance sensors mounted on it are used to measure the local surface temperature. The heat convection equation is then solved for the heat transfer distribution within an interaction, yielding a total uncertainty of about +/- 10 percent. These experimental data are compared with the results of numerical Navier-Stokes solutions which employ a kappa-epsilon turbulence model. Finally, a simplified form of the peak heat transfer correlation for fin interactions is suggested.

Lee, Y.↗
NASA NTRS1991

Wind tunnel investigation of the interaction and breakdown characteristics of slender wing vortices at subsonic, transonic, and supersonic speeds

The vortex dominated aerodynamic characteristics of a generic 65 degree cropped delta wing model were studied in a wind tunnel at subsonic through supersonic speeds. The lee-side flow fields over the wing-alone configuration and the wing with leading edge extension (LEX) added were observed at M (infinity) equals 0.40 to 1.60 using a laser vapor screen technique. These results were correlated with surface streamline patterns, upper surface static pressure distributions, and six-component forces and moments. The wing-alone exhibited vortex breakdown and asymmetry of the breakdown location at the subsonic and transonic speeds. An earlier onset of vortex breakdown over the wing occurred at transonic speeds due to the interaction of the leading edge vortex with the normal shock wave. The development of a shock wave between the vortex and wing surface caused an early separation of the secondary boundary layer. With the LEX installed, wing vortex breakdown asymmetry did not occur up to the maximum angle of attack in the present test of 24 degrees. The favorable interaction of the LEX vortex with the wing flow field reduced the effects of shock waves on the wing primary and secondary vortical flows. The direct interaction of the wing and LEX vortex cores diminished with increasing Mach number. The maximum attainable vortex-induced pressure signatures were constrained by the vacuum pressure limit at the transonic and supersonic speeds.

Erickson, Gary E.↗
NASA NTRS1985

A holographic interferometric study of an axisymmetric shock-wave/boundary-layer strong interaction flow

The results of a holographic interferometric and analytical examination of shock wave/turbulent boundary layer interactions occurring in a flow near a cone-cylinder intersection are reported. A Mach 2.85 flow with an Re of 18 million was used, along with cone angles of 12.5, 20 and 30 deg. Negligible, incipient and large scale separations were observed. The subsonic layer of the boundary always remained thin and was usually penetrated by the shock wave. An Abel transform, applied to the interferometric traces, yielded a great deal of data on the density field when combined with data from application of laser velocimeter, pressure tap and oil flow techniques.

Dunagan, S. E.↗
NASA NTRS1990

Numerical study of shock-wave/boundary layer interactions in premixed hydrogen-air hypersonic flows

A computational study of shock wave/boundary layer interactions involving premixed combustible gases, and the resulting combustion processes is presented. The analysis is carried out using a new fully implicit, total variation diminishing (TVD) code developed for solving the fully coupled Reynolds-averaged Navier-Stokes equations and species continuity equations in an efficient manner. To accelerate the convergence of the basic iterative procedure, this code is combined with vector extrapolation methods. The chemical nonequilibrium processes are simulated by means of a finite-rate chemistry model for hydrogen-air combustion. Several validation test cases are presented and the results compared with experimental data or with other computational results. The code is then applied to study shock wave/boundary layer interactions in a ram accelerator configuration. Results indicate a new combustion mechanism in which a shock wave induces combustion in the boundary layer, which then propagates outwards and downstream. At higher Mach numbers, spontaneous ignition in part of the boundary layer is observed, which eventually extends along the entire boundary layer at still higher values of the Mach number.

Yungster, Shaye↗
NASA NTRS1991

Numerical study of shock-wave/boundary layer interactions in premixed hydrogen-air hypersonic flows

A computational study of shock wave/boundary layer interactions involving premixed combustible gases, and the resulting combustion processes is presented. The analysis is carried out using a new fully implicit, total variation diminishing (TVD) code developed for solving the fully coupled Reynolds-averaged Navier-Stokes equations and species continuity equations in an efficient manner. To accelerate the convergence of the basic iterative procedure, this code is combined with vector extrapolation methods. The chemical nonequilibrium processes are simulated by means of a finite-rate chemistry model for hydrogen-air combustion. Several validation test cases are presented and the results compared with experimental data or with other computational results. The code is then applied to study shock wave/boundary layer interactions in a ram accelerator configuration. Results indicate a new combustion mechanism in which a shock wave induces combustion in the boundary layer, which then propagates outwards and downstream. At higher Mach numbers, spontaneous ignition in part of the boundary layer is observed, which eventually extends along the entire boundary layer at still higher values of the Mach number.

Yungster, Shaye↗
NASA NTRS1998

Spurious Numerical Oscillations in Numerical Simulation of Supersonic Flows Using Shock Capturing Schemes

The numerical simulation of transitional and turbulent processes in hypersonic boundary layers often involves a physical process of a shock-disturbance wave interaction in complex two-dimensional and three-dimensional flow fields. For such simulations, it is required that there be a high order of accuracy in capturing both the shock and the small disturbances. The purpose of this paper is to evaluate the viability of using high order shock capturing schemes to track small disturbances in a multi-dimensional steady hypersonic flow. The numerical methods that are to be studied are the Total Variation Diminishing (TVD) scheme, and Essentially Non-Oscillatory (ENO) scheme. This paper shows that the presence of numerical oscillations in the flow field solution may drastically hinder any attempt at tracking the propagation of any physical disturbances. It has been found that the numerical oscillations that exist for shock capturing methods may be significant enough to pollute a flow field containing small physical disturbances. The effects of the refinement of the grid do not reduce the oscillations, but rather they decrease the wavelength of the oscillations. It is shown that by aligning the shock with the grid, the amplitude of these spurious oscillations may be greatly reduced.

Lee, Theodore K.↗
NASA NTRS1995

Drag measurements of an axisymmetric nacelle mounted on a flat plate at supersonic speeds

An experimental investigation was conducted to determine the effect of diverter wedge half-angle and nacelle lip height on the drag characteristics of an assembly consisting of a nacelle fore cowl from a typical high-speed civil transport (HSCT) and a diverter mounted on a flat plate. Data were obtained for diverter wedge half-angles of 4.0 deg, 6.0 deg, and 8.0 deg and ratios of the nacelle lip height above a flat plate to the boundary-layer thickness (h(sub n)/delta) of approximately 0.87 to 2.45. Limited drag data were also obtained on a complete nacelle/diverter configuration that included fore and aft cowls. Although the nacelle/diverter drag data were not corrected for base pressures or internal flow drag, the data are useful for comparing the relative drag of the configuration tested. The tests were conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.50, 1.80, 2.10, and 2.40 and Reynolds numbers ranging from 2.00 x 10(exp 6) to 5.00 x 10(exp 6) per foot. The results of this investigation showed that the nacelle/diverter drag essentially increased linearly with increasing h(sub n)/delta except near 1.0 where the data showed a nonlinear behavior. This nonlinear behavior was probably caused by the interaction of the shock waves from the nacelle/diverter configuration with the flat-plate boundary layer. At the lowest h(sub n)/delta tested, the diverter wedge half-angle had virtually no effect on the nacelle/diverter drag. However, as h(sub n)/delta increased, the nacelle/diverter drag increased as diverter wedge half-angle increased.

Flamm, Jeffrey D.↗
NASA NTRS1984

Interaction of aerodynamic noise with laminar boundary layers in supersonic wind tunnels

The interaction between incoming aerodynamic noise and the supersonic laminar boundary layer is studied. The noise field is modeled as a Mach wave radiation field consisting of discrete waves emanating from coherent turbulent entities moving downstream within the supersonic turbulent boundary layer. The individual disturbances are likened to miniature sonic booms and the laminar boundary layer is staffed by the waves as the sources move downstream. The mean, autocorrelation, and power spectral density of the field are expressed in terms of the wave shapes and their average arrival rates. Some consideration is given to the possible appreciable thickness of the weak shock fronts. The emphasis in the interaction analysis is on the behavior of the shocklets in the noise field. The shocklets are shown to be focused by the laminar boundary layer in its outer region. Borrowing wave propagation terminology, this region is termed the caustic region. Using scaling laws from sonic boom work, focus factors at the caustic are estimated to vary from 2 to 6 for incoming shocklet strengths of 1 to .01 percent of the free stream pressure level. The situation regarding experimental evidence of the caustic region is reviewed.

Schopper, M. R.↗
NASA NTRS2004

Fuselage Structure Response to Boundary Layer, Tonal Sound, and Jet Noise

Experiments have been conducted to study the response of curved aluminum and graphite-epoxy fuselage structures to flow and sound loads from turbulent boundary layer, tonal sound, and jet noise. Both structures were the same size. The aluminum structure was reinforced with tear stoppers, while the graphite-epoxy structure was not. The graphite-epoxy structure weighed half as much as the aluminum structure. Spatiotemporal intermittence and chaotic behavior of the structural response was observed, as jet noise and tonal sound interacted with the turbulent boundary layer. The fundamental tone distributed energy to other components via wave interaction with the turbulent boundary layer. The added broadband sound from the jet, with or without a shock, influenced the responses over a wider range of frequencies. Instantaneous spatial correlation indicates small localized spatiotemporal regions of convected waves, while uncorrelated patterns dominate the larger portion of the space. By modifying the geometry of the tear stoppers between panels and frame, the transmitted and reflected waves of the aluminum panels were significantly reduced. The response level of the graphite-epoxy structure was higher, but the noise transmitted was nearly equal to that of the aluminum structure. The fundamental shock mode is between 80 deg and 150 deg and the first harmonic is between 20 deg and 80 deg for the underexpanded supersonic jet impinging on the turbulent boundary layer influencing the structural response. The response of the graphite-epoxy structure due to the fundamental mode of the shock impingement was stabilized by an externally fixed oscillator.

Maestrello, L.↗