Search NASA⌕ Search

SEARCH · Search NASA

Results for “similarity analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Space Shuttle Plume and Plume Impingement Study

The extent of the influence of the propulsion system exhaust plumes on the vehicle performance and control characteristics is a complex function of vehicle geometry, propulsion system geometry, engine operating conditions and vehicle flight trajectory were investigated. Analytical support of the plume technology test program was directed at the two latter problem areas: (1) definition of the full-scale exhaust plume characteristics, (2) application of appropriate similarity parameters; and (3) analysis of wind tunnel test data. Verification of the two-phase plume and plume impingement models was directed toward the definition of the full-scale exhaust plume characteristics and the separation motor impingement problem.

Tevepaugh, J. A.↗
NASA NTRS1978

Meteor ablation spheres from deep-sea sediments

Spheres from mid-Pacific abyssal clays (0 to 500,000 yrs old), formed from particles that completely melted and subsequently recrystallized as they separated from their meteoroid bodies, or containing relict grains of parent meteoroids that did not experience any melting were analyzed. The spheres were readily divided into three groups using their dominant mineralogy. The Fe-rich spheres were produced during ablation of Fe and metal-rich silicate meteoroids. The glassy spheres are considerably more Fe-rich than the silicate spheres. They consist of magnetite and an Fe glass which is relatively low in Si. Bulk compositions and relict grains are useful for determining the parent meteoroid types for the silicate spheres. Bulk analyses of recrystallized spheres show that nonvolatile elemental abundances are similar to chondrite abundances. Analysis of relict grains identified high temperature minerals associated with a fine-grained, low temperature, volatile-rich matrix. The obvious candidates for parent meteoroids of this type of silicate sphere is a carbonaceous chondrite.

Blanchard, M. B.↗
NASA NTRS1979

ATMOS Spacelab 1 science investigation

Existing infrared spectra from high speed interferometer balloon flights were analyzed and experimental analysis techniques applicable to similar data from the ATMOS experiment (Spacelab 3) were investigated. Specific techniques under investigation included line-by-line simulation of the spectra to aid in the identification of absorbing gases, simultaneous retrieval of pressure and temperature profiles using carefully chosen pairs of CO2 absorption lines, and the use of these pressures and temperatures in the retrieval of gas concentration profiles for many absorbing species. A search for a new absorption features was also carried out, and special attention was given to identification of absorbing gases in spectral bandpass regions to be measured by the halogen occultation experiment.

Park, J. H.↗
NASA NTRS1980

Computer-aided roll pass design in rolling of airfoil shapes

This paper describes two computer-aided design (CAD) programs developed for modeling the shape rolling process for airfoil sections. The first program, SHPROL, uses a modular upper-bound method of analysis and predicts the lateral spread, elongation, and roll torque. The second program, ROLPAS, predicts the stresses, roll separating force, the roll torque and the details of metal flow by simulating the rolling process, using the slab method of analysis. ROLPAS is an interactive program; it offers graphic display capabilities and allows the user to interact with the computer via a keyboard, CRT, and a light pen. The accuracy of the computerized models was evaluated by (a) rolling a selected airfoil shape at room temperature from 1018 steel and isothermally at high temperature from Ti-6Al-4V, and (b) comparing the experimental results with computer predictions. The comparisons indicated that the CAD systems, described here, are useful for practical engineering purposes and can be utilized in roll pass design and analysis for airfoil and similar shapes.

Akgerman, N.↗
NASA NTRS1982

Anomalous behavior of the Pioneer Venus entry probes during lower descent

Four Pioneer Venus Probe spacecraft entered the Venusian atmosphere on December 9 1978, and descended to the surface while making in situ measurements of chemical composition, structure, and radiative balance. In the lower Venusian atmosphere, a number of anomalous events were noted in some of the scientific instruments and Probe engineering data. Many of these anomalies occurred on each of the Probes at approximately the same altitude. The anomalies are thought to be the result of some unexpected electrical interaction between the Probe and the Venusian atmosphere. This conclusion is based on analysis and testing of similar Probe hardware on the ground. However, the possibility that some anomalies were a result of latent design of manufacturing flaws cannot be ruled out.

Polaski, L. J.↗
NASA NTRS1988

Discrimination of hydrothermal alteration mineral assemblages at Virginia City, Nevada, using the airborne imaging spectrometer

The purpose of this study is to use airborne imaging spectrometer data to discriminate hydrothermal alteration mineral assemblages associated with silver and gold mineralization at Virginia City, NV. The data is corrected for vertical striping and sample gradients, and converted to flat-field logarithmic residuals. Log residual spectra from areas known to be altered are compared to field spectra for kaolinitic, illitic, sericitic, and propylitic alteration types. The areal distributions of these alteration types are estimated using a spectral matching technique. Both visual examination of spectra and the matching techniques are effective in distinguishing kaolinitic, illitic, and propylitic alteration types from each other. However, illitic and sericitic alteration cannot be separated using these techniques because the spectra of illite and sericite are very similar. A principal components analysis of 14 channels in the 2.14-2.38 micron wavelength region is also successful in discriminating and mapping illitic, kaolinitic, and propylitic alteration types.

Hutsinpiller, Amy↗
NASA NTRS1990

Methodology for estimating helicopter performance and weights using limited data

Methodology is developed and described for estimating the flight performance and weights of a helicopter for which limited data are available. The methodology is based on assumptions which couple knowledge of the technology of the helicopter under study with detailed data from well documented helicopters thought to be of similar technology. The approach, analysis assumptions, technology modeling, and the use of reference helicopter data are discussed. Application of the methodology is illustrated with an investigation of the Agusta A129 Mangusta.

Baserga, Claudio↗
NASA NTRS1991

The dust coma of Comet Austin (1989c1)

Thermal-infrared (10 and 20 micron) images of Comet Austin were obtained on UT 30.6 Apr., 1.8, 2.8, and 3.6 May 1990. The NASA-Marshall Space Flight Center 20 pixel bolometer array at the NASA 3 meter Infrared Telescope Facility in Hawaii was used. The 10.8 micron (FWHM = 5.3 microns) maps were obtained with maximum dimensions of 113 arcsec (57,500 km) in RA and 45 arcsec (23,000 km) in declination, with a pixel size of 4.2 x 4.2 arcsec. A smaller, 45 x 18 arcsec, map was obtained in the 19.2 micron (FWHM = 5.2 microns) bandpass. At the time of these observations Comet Austin's heliocentric and geocentric distances were 0.7 and 0.5 AU respectively. The peak flux density (within the brightest pixel) was 23 + or - 2 Janskys for the first three dates and only marginally lower the last day; i.e., within the observational uncertainties no evidence was found for day-to-day variability like that observed in Comet Halley. A dynamical analysis of the morphology of the extended dust emission is used to constrain the size distribution and production rate of the dust particles. The results of this analysis are compared with similar studies carried out on comets P/Giacobini-Zinner, P/Brorsen-Metcalf, P/Halley, P/Tempel 2, and Wilson (1987).

Campins, Humberto↗
NASA NTRS1992

Large-gap magnetic suspension systems

The classification of magnetic suspension devices into small-gap and large-gap categories is addressed. The relative problems of position sensing, control systems, power supplies, electromagnets, and magnetic field or force analysis are discussed. The similarity of all systems from a controls standpoint is qualified. Some applications where large-gap technology is being applied to systems with a physically small air-gap are mentioned. Finally, the applicability of some other suspension approaches, such as electrodynamic or superconducting are briefly addressed.

Britcher, Colin P.↗
NASA NTRS1992

Simulated orbital impact of multi-wall composite structures

This paper presents the results of an experimental investigation in which several different composite materials were tested for their ability to prevent the perforation of multiwall systems under hypervelocity projectile impact. The damage in the composite specimens is compared to the damage in aluminum specimens of similar geometry and weight caused by hypervelocity projectiles with similar impact energies. The analysis shows that using composite materials in combination with metallic materials in multiwall structures can increase the protection afforded a spacecraft against perforation by orbital debris over that provided by traditional, purely metallic multiwall structures.

Walker, Eve J.↗
NASA NTRS1995

Wave Journal Bearing. Part 2: Experimental Pressure Measurements and Fractional Frequency Whirl Threshold for Wave and Plain Journal Bearings

A new hydrodynamic bearing concept, the wave journal bearing, is being developed because it has better stability characteristics than plain journal bearings while maintaining similar load capacity. An analysis code to predict the steady state and dynamic performance of the wave journal bearing is also part of the development. To verify numerical predictions and contrast the wave journal bearing's stability characteristics to a plain journal bearing, tests were conducted at NASA Lewis Research Center using an air bearing test rig. Bearing film pressures were measured at 16 ports located around the bearing circumference at the middle of the bearing length. The pressure measurements for both a plain journal bearing and a wave journal bearing compared favorably with numerical predictions. Both bearings were tested with no radial load to determine the speed threshold for self-excited fractional frequency whirl. The plain journal bearing started to whirl immediately upon shaft start-up. The wave journal did not incur self-excited whirl until 800 to 900 rpm as predicted by the analysis. Furthermore, the wave bearing's geometry limited the whirl orbit to less than the bearing's clearance. In contrast, the plain journal bearing did not limit the whirl orbit, causing it to rub.

Walker, James F.↗
NASA NTRS1999

An Assessment of Technical and Production Risks of Candidate Low-Cost Attitude/Heading Reference Systems(AHRS)

This report provides an assessment of technical and production risks of candidate low-cost attitude/heading reference systems (AHRS) for use in the Advanced General Aviation Transport Experiments (AGATE) airplanes. A low-cost AHRS is a key component of modem "glass cockpit" flight displays for General Aviation (GA) aircraft. The technical capabilities of several candidate low-cost AHRS were examined and described along with the technical issues involved with using all solid-state components for attitude measurement. An economic model was developed which describes the expected profit, rate of return, and volume requirements for the manufacture of low-cost AHRS for GA aircraft in the 2000 to 2020 time frame. The model is the result of interviews with GA airframe manufacturers, avionics manufacturers and historical analysis of avionics of similar complexity. The model shows that a manufacturer will break even after three years of AHRS production, realizing an 18 percent rate of return (23 percent profit) on an investment of $3.5M over the 20 year period. A start-up production estimate showed costs of $6-12M for a new company to build and certify an AHRS from scratch, considered to be a high-risk proposition, versus $0.25-0.75M for an experienced avionics manufacturer to manufacture a design under license, a low-risk proposition.

Yuchnovicz, Daniel↗
NASA NTRS2001

Transition In Supersonic Flows With Corners

It is proposed to investigate the effect of sudden change in the slope of the surface on the stability and transition onset point in supersonic and hypersonic boundary layers. Since we can not use the linear stability theory in flows where there are discontinuities we have to solve the full Navier-Stokes equations to determine the amplification of the disturbances across the oblique shock which exists at the corner. We will use the Navier-Stokes code which was developed by Dr. Harold Atkins in the aerodynamic and acoustic methods branch. The code is developed using the higher order ENO scheme and is currently set up for two-dimensional flows. In the first year of our investigation, we will investigate the evolution of small amplitude two-dimensional disturbances and determine the N-factors for the most amplified disturbances. We will perform the analysis for the parameter similar to X-31 model and flight experiment conditions. From these computation we will infer what is the maximum amplification rate possible in quite environments without any tripping devices. In the second part of the investigation, we will perform nonlinear computations to determine what is the minimum amplitudes necessary to cause the transition at a designed location. In the third part, we have to determine what kind of trip devices necessary to excite the required disturbances. The principal investigator of this project is Dr. P. Balakumar, Associate Professor of Department of Aerospace Engineering, Old Dominion University. We will actively collaborate with research scientists in the Aero-Thermodynamics Branch at NASA/Langley Research Center. A half-time graduate student will also participate in the project.

Balakumar, P.↗
NASA NTRS1997

Design and Operational Evaluation of the Traffic Management Advisor at the Ft. Worth Air Route Traffic Control Center

NASA and the FAA have designed and developed and an automation tool known as the Traffic Management Advisor (TMA). The system was operationally evaluated at the Ft. Worth Air Route Traffic Control Center (ARTCC). The TMA is a time-based strategic planning tool that provides Traffic Management Coordinators and En Route Air Traffic Controllers the ability to efficiently optimize the capacity of a demand impacted airport. The TMA consists of trajectory prediction, constraint-based runway scheduling, traffic flow visualization and controllers advisories. The TMA was used and operationally evaluated for forty-one rush traffic periods during a one month period in the Summer of 1996. The evaluations included all shifts of air traffic operations as well as periods of inclement weather. Performance data was collected for engineering and human factor analysis and compared with similar operations without the TMA. The engineering data indicates that the operations with the TMA show a one to two minute per aircraft delay reduction during rush periods. The human factor data indicate a perceived reduction in en route controller workload as well as an increase in job satisfaction. Upon completion of the evaluation, the TMA has become part of the normal operations at the Ft. Worth ARTCC.

Swenson, Harry N.↗
NASA NTRS1997

Incompressible Navier-Stokes Computations in Aerospace and Beyond

Challenges in applying CFD to real world problems will be discussed using incompressible flow examples. Despite the remarkable progress made in CFD technology during the past two decades, new challenges are ahead of us. Some of these will be discussed in conjunction with the incompressible Navier-Stokes solver development and their applications. Computed examples include wing tip vortex formation and propagation, flow simulation of an advanced rocket pump, and an extension of the similar technology to biofluid analysis and design. Numerical issues dealing with these applications will be discussed both from algorithm development and from application point of view. The material will be printed in a bound volume after the symposium.

Kwak, Dochan↗
NASA NTRS2005

Identification of a typical flight patterns

Method and system for analyzing aircraft data, including multiple selected flight parameters for a selected phase of a selected flight, and for determining when the selected phase of the selected flight is atypical, when compared with corresponding data for the same phase for other similar flights. A flight signature is computed using continuous- valued and discrete-valued flight parameters for the selected flight parameters and is optionally compared with a statistical distribution of other observed flight signatures, yielding a typicality scores for the same phase for other similar flights. A cluster analysis is optionally applied to the flight signatures to define an optimal collection of clusters. A level of atypicality for a selected flight is estimated, based upon an index associated with the cluster analysis.

Irving C Statler↗
NASA NTRS2005

Identification of atypical flight patterns

Method and system for analyzing aircraft data, including multiple selected flight parameters for a selected phase of a selected flight, and for determining when the selected phase of the selected flight is atypical, when compared with corresponding data for the same phase for other similar flights. A flight signature is computed using continuous-valued and discrete-valued flight parameters for the selected flight parameters and is optionally compared with a statistical distribution of other observed flight signatures, yielding atypicality scores for the same phase for other similar flights. A cluster analysis is optionally applied to the flight signatures to define an optimal collection of clusters. A level of atypicality for a selected flight is estimated, based upon an index associated with the cluster analysis.

Statler, Irving C.↗
NASA NTRS2012

Numerical Study of Pressure Fluctuations due to High-Speed Turbulent Boundary Layers

Direct numerical simulations (DNS) are used to examine the pressure fluctuations generated by fully developed turbulence in supersonic turbulent boundary layers with an emphasis on both pressure fluctuations at the wall and the acoustic fluctuations radiated into the freestream. The wall and freestream pressure fields are first analyzed for a zero pressure gradient boundary layer with Mach 2.5 and Reynolds number based on momentum thickness of approximately 2835. The single and multi-point statistics reported include the wall pressure fluctuation intensities, frequency spectra, space-time correlations, and convection velocities. Single and multi-point statistics of surface pressure fluctuations show good agreement with measured data and previously published simulations of turbulent boundary layers under similar flow conditions. Spectral analysis shows that the acoustic fluctuations outside the boundary layer region have much lower energy content within the high-frequency region. The space-time correlations reflect the convective nature of the pressure field both at the wall and in the freestream, which is characterized by the downstream propagation of pressure-carrying eddies. Relative to those at the wall, the pressure-carrying eddies associated with the freestream signal are larger and convect at a significantly lower speed. The preliminary DNS results of a Mach 6 boundary layer show that the pressure rms in the freestream region is significantly higher than that of the lower Mach number case.

Duan, Lian↗