Search NASA⌕ Search

SEARCH · Search NASA

Results for “sounding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

An analysis of sound absorbing linings for the interior of the NASA Ames 80 x 120-foot wind tunnel

It is desirable to achieve low frequency sound absorption in the tests section of the NASA Ames 80X120-ft wind tunnel. However, it is difficult to obtain information regarding sound absorption characteristics of potential treatments because of the restrictions placed on the dimensions of the test chambers. In the present case measurements were made in a large enclosure for aircraft ground run-up tests. The normal impedance of the acoustic treatment was measured using two microphones located close to the surface of the treatment. The data showed reasonably good agreement with analytical methods which were then used to design treatments for the wind tunnel test section. A sound-absorbing lining is proposed for the 80X120-ft wind tunnel.

Wilby, J. F.↗

Determination of total ozone from HIRS2/MSU sounding data

The total ozone fields computed from the High Resolution Infrared Sounder 2/Microwave Sounding Unit (HIRS2/MSU) are somewhat noisy compared to Total Ozone Mapping Spectrometer (TOMS) results and show latitude dependent systematic errors which vary slowly in time. Researchers used systematic errors from previous time periods to correct the HIRS2 soundings. Comparison of fields of HIRS2 and TOMS derived ozone are shown. Results are encouraging and indicate useful soundings of total O sub 3 burden can be done at night and in the polar winter. Ideally, joint infrared, microwave, and ultraviolet systems should be flown on low Earth orbiting and geostationary satellites to best utilize the complementary nature of the observations.

Susskind, Joel↗

Active control of sound fields in elastic cylinders by multi-control forces

An unstiffened cylindrical model was used to study the control of sound transmission into aircraft cabins by the use of multi-control forces applied directly to the cylinder wall. External acoustic monopoles were located on each side of the cylinder to approximate the propeller noise source. This allowed the study of a dual control system utilizing multi-control forces in conjunction with synchrophasing of the twin acoustic monopole sources. For acoustic resonant conditions within the cavity, a spatially averaged noise reduction of approximately 30 dB was achieved using the active control system for both in-phase and out-of-phase monopoles; however, effective reduction of the sound field was dependent upon judiciously positioning the control forces for optimal control of the sound field.

Jones, J. D.↗

Reduction of sound transmission through fuselage walls by alternate resonance tuning (A.R.T.)

The ability of alternate resonance tuning (ART) to block sound transmission through light-weight flexible paneled walls by controlling the dynamics of the wall panels is considered. Analytical results for sound transmission through an idealized panel wall illustrate the effect of varying system parameters and show that one or more harmonics of the incident sound field can be cancelled by the present method. Experimental results demonstrate that very large transmission losses with reasonable bandwidths can be achieved by a simple ART panel barrier in a duct.

Bliss, Donald B.↗

Laser Schlieren System Detects Sounds Of Leaks

Hostile environments monitored safely and noninvasively. Modified laser schlieren system acts as microphone to detect sounds of leaks remotely. Sensitive to acoustical frequencies above audible range and especially suited for monitoring leaks of high-pressure steam from boilers or chemical vapors from processing equipment. Does not require placement of delicate equipment in harsh environment monitored, and no contact needed with boiler or other unit being monitored. Detects sound waves via variation of index of refraction of air at acoustical frequencies. Used to monitor sound frequencies beyond range of human hearing.

Shakkottai, Parthasarathy P.↗

Application of sound and temperature to control boundary-layer transition

The growth and decay of a wave packet convecting in a boundary layer over a concave-convex surface and its active control by localized surface heating are studied numerically using direct computations of the Navier-Stokes equations. The resulting sound radiations are computed using linearized Euler equations with the pressure from the Navier-Stokes solution as a time-dependent boundary condition. It is shown that on the concave portion the amplitude of the wave packet increases and its bandwidth broadens while on the convex portion some of the components in the packet are stabilized. The pressure field decays exponentially away from the surface and then algebraically, exhibiting a decay characteristic of acoustic waves in two dimensions. The far-field acoustic behavior exhibits a super-directivity type of behavior with a beaming downstream. Active control by surface heating is shown to reduce the growth of the wave packet but have little effect on acoustic far field behavior for the cases considered. Active control by sound emanating from the surface of an airfoil in the vicinity of the leading edge is experimentally investigated. The purpose is to control the separated region at high angles of attack. The results show that injection of sound at shedding frequency of the flow is effective in an increase of lift and reduction of drag.

Maestrello, Lucio↗

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, Ramani↗

Techniques and applications for binaural sound manipulation in human-machine interfaces

The implementation of binaural sound to speech and auditory sound cues (auditory icons) is addressed from both an applications and technical standpoint. Techniques overviewed include processing by means of filtering with head-related transfer functions. Application to advanced cockpit human interface systems is discussed, although the techniques are extendable to any human-machine interface. Research issues pertaining to three-dimensional sound displays under investigation at the Aerospace Human Factors Division at NASA Ames Research Center are described.

Begault, Durand R.↗

Active control of structurally-coupled sound fields in elastic cylinders by vibrational force inputs

Active control of structurally-coupled sound fields in elastic cylinders is analytically and experimentally studied. The primary (noise) field in the cylinder model is generated by the coupled dynamic response of the shell under loading by a single exterior acoustic source. Control of the interior sound field is achieved by applying vibrational force inputs directly to the shell wall. Action of the point controllers serve to increase the input impedance of select structural modes of the shell which are well-coupled to the interior acoustic cavity, thus substantially reducing sound transmission into the cavity. Spatially-averaged noise reductions in excess of 30 dB are demonstrated for acoustic resonant conditions within the cavity. Twin controller configurations are presented which demonstrate the ability to independently control orthogonal modes of the interior acoustic space. Benefits and drawbacks of this new methodology for noise control are discussed and clearly demonstrated.

Jones, J. D.↗

Satellite sound broadcast propagation studies and measurements

Satellite Sound Broadcasting is an attractive satellite application. Before regulatory decisions can be made in 1992, the propagation effects encountered have to be characterized. The Electrical Engineering Research Laboratory has nearly completed a system which will allow amplitude measurements to be made over 10 MHz bandwidths in the 800 to 1800 MHz frequency range. The system uses transmission from a transportable tower, and reception inside buildings or in the shadow of trees or utility poles. The goal is to derive propagation models for use by systems engineers who are about to design satellite broadcast systems. The advance of fiber-optics technology has helped to focus future development of satellite services into areas where satellites are uniquely competitive. One of these preferred satellite applications is the broadcasting of high-quality sound for stationary or mobile reception by listeners using low-cost, consumer-grade receivers. Before such services can be provided, however, the political hurdles of spectrum allocation have to be surmounted and the technical questions of standardization for world-wide compatibility have to be resolved. In order to arrive at an optimal system design, efficient in the use of our scarce spectral resources, affordable both to the broadcaster and the listener, and providing predictable performance, the propagation effects to which the service is subjected have to be characterized. Consequently, the objective of the research project is to make basic propagation measurements for direct Satellite Sound Broadcasting Service (SSBS). The data obtained should allow the development of propagation models to be used by communications engineers designing the operational systems. Such models shall describe the effects of shadowing and multipath propagation on SSBS receivers operating in a specified environment, such as inside commercial or residential buildings of various construction and also in the shadow of trees or utility poles as might be encountered by transporting or mobile listeners.

Vogel, Wolfhard J.↗

Fourth International Symposium on Long-Range Sound Propagation

Long range sound propagation is an aspect of many acoustical problems ranging from en route aircraft noise to the acoustic detection of aircraft. Over the past decade, the University of Mississippi and the Open University of England, together with a third institution, have held a symposium approx. every 2 years so that experts in the field of long range propagation could exchange information on current research, identify areas needing additional work, and coordinate activities as much as possible. The Fourth International Symposium on Long Range Sound Propagation was jointly sponsored by the University of Mississippi, the Open University of England, and NASA. Papers were given in the following areas: ground effects on propagation; infrasound propagation; and meteorological effects on sound propagation. A compilation of the presentations made at the symposium is presented along with a list of attendees, and the agenda.

Willshire, William L., Jr.↗

Sound generation by a stenosis in a pipe

This paper presents a computational aeroacoustics study of sound generated by low Mach number flow through a closure (stenosis) in a circular pipe. The time-dependent incompressible flowfield in the pipe is first computed utilizing a vorticity/stream function formulation. The known velocity field is then utilized to determine the incompressible fluctuating pressure in the pipe. This hydrodynamic pressure field is then utilized to compute a hydrodynamic density perturbation to the constant incompressible density through the equation of state. Knowledge of this complete hydrodynamic field is then employed as the source of the resulting sound radiation. This tripartite technique allows separation of the compressible fluctuations from the purely hydrodynamic fluctuations. Results of the analysis are compared with experimental measurements of sound radiated by such a flow.

Hardin, J. C.↗

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, R.↗

An experimental investigation of the active control of sound transmission into a cylindrical enclosure

Preliminary results are reported from experiments involving the use of vibration sources in the active control of sound transmission into a cylindrical chamber (as in aircraft cabin-noise suppression). Electrodynamic shakers are used to provide vibrational excitation in a 3-m-high 900-mm-diameter cylindrical stainless-steel chamber with damped ends, subjected to single-frequency (384-Hz) sound from a horn driver located 150 mm from the cylinder midway along its length. When vibration is applied only diametrically opposite the source, rotation of the sound field occurs, but global attenuation is not achieved; with additional vibration applied at an angle of 225 deg to the source, moderate reduction of the global field is obtained. The need to identify and control all offending coupled structural/acoustic modes is indicated.

Snyder, S. D.↗

Direct computation of the sound from a compressible co-rotating vortex pair

The far-field sound from corotating vortices is computed by direct computation of the unsteady, compressible Navier-Stokes equations on a computational mesh that extends to two acoustic wavelengths in all directions. The vortices undergo a period of corotation followed by a sudden merger. A 2D version of Moehring's equation is developed and used in conjunction with source terms computed in the simulation to predict the far-field sound. The prediction agrees with the simulation to within 3 percent. Results of far-field pressure fluctuations for an acoustically noncompact case are also presented for which the prediction is 66 percent too high. Results also indicate that the monopole contribution of 'viscous sound' is negligible for this flow.

Mitchell, Brian E.↗

Active control of sound transmission/radiation from elastic plates by vibration inputs. II - Experiments

Actively controlled harmonic force inputs were applied experimentally to reduce the sound transmitted through an elastic circular plate. The control implementation used a time domain least mean square adaptive algorithm with two error sensors. The control forces were applied directly to the plate by point force vibration inputs, while the error information and performance were measured in the radiated acoustic field by microphones. Test cases were also performed in which the error sensors were accelerometers mounted on the plate. When accelerometers were used as error sensors, the controller performance was degraded; leading to the conclusion that minimizing plate motion does not necessarily lead to an associated decrease in radiated sound levels. In contrast, the results show excellent attenuation of the transmitted sound field when microphone error sensors were used. This result was consistent over a range of frequencies. In addition, the experimental results are compared to previously derived analytical results and the effect of using a point or global minimization scheme is discussed.

Metcalf, V. L.↗

Techniques and applications for binaural sound manipulation in human-machine interfaces

The implementation of binaural sound to speech and auditory sound cues (auditory icons) is addressed from both an applications and technical standpoint. Techniques overviewed include processing by means of filtering with head-related transfer functions. Application to advanced cockpit human interface systems is discussed, although the techniques are extendable to any human-machine interface. Research issues pertaining to three-dimensional sound displays under investigation at the Aerospace Human Factors Division at NASA Ames Research Center are described.

Begault, Durand R.↗

Possibility to sound the atmospheric ozone by a radiosonde equipped with two temperature sensors, sensitive and non-sensitive to the long wave radiation

The sensitiveness of white coated thermistor sensors and non-sensitiveness of the gold coated over white thermistor sensors (which have been manufactured by a vacuum evaporation process) to long wave radiation were ascertained by some simple experiments in-room and also by analyses of some results of experimental soundings. From results of analyses on the temperature discrepancies caused by long wave radiation, the possibility to sound the atmospheric ozone partial pressure by a radiosonde equipped with two kinds of sensors, sensitive and non-sensitive to the long wave radiation was suggested, and the test results of the newly developed software for the deduction of ozone partial pressure in upper layers was also shown. However, it was found that the following is the necessary condition to realize the purpose. The sounding should be made by a radiosonde equipped with three sensors, instead of two, one being non-sensitive to the long wave radiation perfectly, and the other two also non-sensitive partially to the downward one, with two different angles of exposure upward. It is essential for the realization of the purpose to get two different values of temperature discrepancies simultaneously observed by the three sensors mentioned above and to avoid the troublesome effects of the upward long wave radiation.

Kitaoka, T.↗