SEARCH · Search NASA

Results for “system level”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS2011

MW-Class Electric Propulsion System Designs

Electric propulsion systems are well developed and have been in commercial use for several years. Ion and Hall thrusters have propelled robotic spacecraft to encounters with asteroids, the Moon, and minor planetary bodies within the solar system, while higher power systems are being considered to support even more demanding future space science and exploration missions. Such missions may include orbit raising and station-keeping for large platforms, robotic and human missions to near earth asteroids, cargo transport for sustained lunar or Mars exploration, and at very high-power, fast piloted missions to Mars and the outer planets. The Advanced In-Space Propulsion Project, High Efficiency Space Power Systems Project, and High Power Electric Propulsion Demonstration Project were established within the NASA Exploration Technology Development and Demonstration Program to develop and advance the fundamental technologies required for these long-range, future exploration missions. Under the auspices of the High Efficiency Space Power Systems Project, and supported by the Advanced In-Space Propulsion and High Power Electric Propulsion Projects, the COMPASS design team at the NASA Glenn Research Center performed multiple parametric design analyses to determine solar and nuclear electric power technology requirements for representative 300-kW class and pulsed and steady-state MW-class electric propulsion systems. This paper describes the results of the MW-class electric power and propulsion design analysis. Starting with the representative MW-class vehicle configurations, and using design reference missions bounded by launch dates, several power system technology improvements were introduced into the parametric COMPASS simulations to determine the potential system level benefits such technologies might provide. Those technologies providing quantitative system level benefits were then assessed for technical feasibility, cost, and time to develop. Key assumptions and primary results of the COMPASS MW-class electric propulsion power system study are reported, and discussion is provided on how the analysis might be used to guide future technology investments as NASA moves to more capable high power in-space propulsion systems.

LaPointe, Michael R.↗

NASA NTRS1977

A multilevel approach for minimum weight structural design including local and system buckling constraints

A rational multilevel approach for minimum weight structural design of truss and wing structures including local and system buckling constraints is presented. Overall proportioning of the structure is achieved at the system level subject to strength, displacement and system buckling constraints, while the detailed component designs are carried out separately at the component level satisfying local buckling constraints. Total structural weight is taken to be the objective function at the system level while employing the change in the equivalent system stiffness of the component as the component level objective function. Finite element analysis is used to predict static response while system buckling behavior is handled by incorporating a geometric stiffness matrix capability. Buckling load factors and the corresponding mode shapes are obtained by solving the eigenvalue problem associated with the assembled elastic stiffness and geometric stiffness matrices for the structural system. At the component level various local buckling failure modes are guarded against using semi-empirical formulas. Mathematical programming techniques are employed at both the system and component level.

Schmit, L. A., Jr.↗

NASA NTRS1990

Flight elements: Fault detection and fault management

Fault management for an intelligent computational system must be developed using a top down integrated engineering approach. An approach proposed includes integrating the overall environment involving sensors and their associated data; design knowledge capture; operations; fault detection, identification, and reconfiguration; testability; causal models including digraph matrix analysis; and overall performance impacts on the hardware and software architecture. Implementation of the concept to achieve a real time intelligent fault detection and management system will be accomplished via the implementation of several objectives, which are: Development of fault tolerant/FDIR requirement and specification from a systems level which will carry through from conceptual design through implementation and mission operations; Implementation of monitoring, diagnosis, and reconfiguration at all system levels providing fault isolation and system integration; Optimize system operations to manage degraded system performance through system integration; and Lower development and operations costs through the implementation of an intelligent real time fault detection and fault management system and an information management system.

Lum, H.↗

NASA NTRS2003

Closed-Loop Performance Measures for Flight Controllers Subject to Neutron-Induced Upsets

It has been observed that atmospheric neutrons can produce single event upsets in digital flight control hardware. The phenomenon has been studied extensively at the chip level, and now system level experiments are underway. In this paper analytical closed-loop performance measures for the tracking error are developed for a plant that is stabilized by a recoverable computer system subject to neutron induced upsets. The underlying model is a Markov jump-linear system with process noise. The steady-state tracking error is expressed in terms of a generalized observability Gramian.

Gray, W. Steven↗

NASA NTRS2014

Development of a Bayesian Belief Network Runway Incursion Model

In a previous paper, a statistical analysis of runway incursion (RI) events was conducted to ascertain their relevance to the top ten Technical Challenges (TC) of the National Aeronautics and Space Administration (NASA) Aviation Safety Program (AvSP). The study revealed connections to perhaps several of the AvSP top ten TC. That data also identified several primary causes and contributing factors for RI events that served as the basis for developing a system-level Bayesian Belief Network (BBN) model for RI events. The system-level BBN model will allow NASA to generically model the causes of RI events and to assess the effectiveness of technology products being developed under NASA funding. These products are intended to reduce the frequency of RI events in particular, and to improve runway safety in general. The development, structure and assessment of that BBN for RI events by a Subject Matter Expert panel are documented in this paper.

Green, Lawrence L.↗

NASA NTRS1992

The effect of acceleration versus displacement methods on steady-state boundary forces

This study describes the acceleration and displacement methods for use in the recovery of coupled system boundary forces. A simple two degree of freedom system has been used for illustration. The effect of the choice of method for use with indeterminate or over-constrained boundaries has been investigated. It has specifically looked at results from a simple two dimensional beam problem using both methods. Much work has been done on the effect of Craig-Bampton modal truncation system displacements and forces, however, little work has been done on system level modal truncation. The findings of this study indicate that the effect of this system level truncation is significant. This may be particularly true for the 35 Hz system cutoff frequency that is required by the space shuttle. From this study's findings, recommendations for areas of study with space shuttle payload systems are made.

Mcghee, D. S.↗

NASA NTRS1994

Self contamination effects in the TAUVEX UV Telescope: Ground testing and computer simulation

The contamination effects due to outgassing from construction materials of the TAUVEX (Tel Aviv University UV Telescope) were evaluated using a combination of ground testing and computer simulations. Tests were performed from the material level of the system level including: (1) High sensitivity CVCM(10(exp -3 percent) measurements of critical materials. (2) Optical degradation measurements of samples specially contaminated by outgassing products at different contamination levels. (3) FTIR studies of chemical composition of outgassed products on above samples. (4) High resolution AFM studies of surface morphology of contaminated surfaces. The expected degradation of TAUVEX performance in mission was evaluated applying a computer simulation code using input parameters determined experimentally in the above tests. The results have served as guidelines for the proper selection of materials, cleanliness requirements, determination of the thermal conditions of the system and bakeout processes.

Lifshitz, Y.↗

NASA NTRS1984

Thermal mathematical modeling and system simulation of Space Shuttle less subsystem

Applications, validation tests, and upgrades of the two- and three-dimensional system level thermal mathematical system simulation models (TMSSM) used for thermal protection system (TPS) analyses are described. The TMSSM were developed as an aid to predicting the performance requirements and configurations of the Shuttle wing leading edge (WLE) and nose cone (NC) TPS tiles. The WLE and its structure were subjected to acoustic, thermal/vacuum, and air loads tests to simulate launch, on-orbit, and re-entry behavior. STS-1, -2 and -5 flight data led to recalibration of on-board instruments and raised estimates of the thermal shock at the NC and WLE. Baseline heating data are now available for the design of future TPS.

Chao, D. C.↗

NASA NTRS1986

Fault-free performance validation of avionic multiprocessors

This paper describes the application of a portion of a validation methodology to NASA's Fault-Tolerant Multiprocessor System (FTMP) and the Software Implemented Fault-Tolerance (SIFT) computer system. The methodology entails a building block approach, starting with simple baseline experiments and building to more complex experiments. The goal of the validation methodology is to thoroughly test and characterize the performance and behavior of ultrareliable computer systems. The validation methodology presented in this paper showed that the methodology is not machine specific and can be used in lieu of life testing approaches. By applying a building block approach at the systems level, the machine complexity was broken down to manageable levels independent of system implementation.

Czeck, Edward W.↗

NASA NTRS2005

Proceedings of the Fifth Integrated Communications, Navigation, and Surveillance (ICNS) Conference and Workshop

Contents includes papers on the following: JPDO: Inter-Agency Cooperation for the Next Generation ATS; R&T Programs; Integrated CNS Systems and Architectures; Datalink Communication Systems; Navigation, System Demonstrations and Operations; Safety and Security Initiatives Impacting CNS; Global Communications Initiatives; Airborne Internet; Avionics for System-Level Enhancements; SWIM (System Wide Information Management); Weather Products and Data Dissemination Technologies; Airsapce Communication Networks; Surveillance Systems; Workshop Breakouts Sessions and ; ICNS Conference Information.

Fujikawa, Gene↗

NASA NTRS2014

Development and Testing of an ISRU Soil Mechanics Vacuum Test Facility

For extraterrestrial missions, earth based testing in relevant environments is key to successful hardware development. This is true for both early component level development and system level integration. For In-Situ Resource Utilization (ISRU) on the moon, hardware must interface with the surface material, or regolith, in a vacuum environment. A relevant test environment will therefore involve a vacuum chamber with a controlled, properly conditioned bed of lunar regolith simulant. However, in earth-based granular media, such as lunar regolith simulant, gases trapped within the material pore structures and water adsorbed to all particle surfaces will release when exposed to vacuum. Early vacuum testing has shown that this gas release can occur violently, which loosens and weakens the simulant, altering the consolidation state. A mid-size chamber (3.66 m tall, 1.5 m inner diameter) at the NASA Glenn Research Center has been modified to create a soil mechanics test facility. A 0.64 m deep by 0.914 m square metric ton bed of lunar simulant was placed under vacuum using a variety of pumping techniques. Both GRC-3 and LHT-3M simulant types were used. Data obtained from an electric cone penetrometer can be used to determine strength properties at vacuum including: cohesion, friction angle, bulk density and shear modulus. Simulant disruptions, caused by off-gassing, affected the strength properties, but could be mitigated by reducing pump rate. No disruptions were observed at pressures below 2.5 Torr, regardless of the pump rate. The slow off-gassing of the soil at low pressure lead to long test times; a full week to reach 10(exp -5) Torr. Robotic soil manipulation would enable multiple ISRU hardware test within the same vacuum cycle. The feasibility of a robotically controlled auger and tamper was explored at vacuum conditions.

lunar regolith↗

NASA NTRS2020

Development of a Thermal Management System for Electrified Aircraft

This paper describes the development and optimization of a conceptual thermal management system for electrified aircraft. Here, a vertical takeoff and landing (VTOL) vehicle is analyzed with the following electrically sourced heat loads considered: motors, generators, rectifiers, and inverters. The vehicle will employ liquid-cooling techniques in order to acquire, transport, and reject waste heat from the vehicle. The purpose of this paper is to threefold: 1) Present a potential modeling framework for system level thermal management system simulation, 2) Analyze typical system characteristics, and 3) Perform optimization on a system developed for a specific vehicle to minimize weight gain, power utilization, and drag. Additionally, the paper will study the design process, specifically investigating the differences between steady state and transient sizing, comparing simulation techniques with a lower fidelity option and quantifying expected error.

Chapman, Jeffryes W.↗

NASA NTRSDate not supplied

Data-Centric Operational Design Domain Characterization for Machine Learning-Based Aeronautical Products

We give for Machine Learning (ML)-based aeronautical products, a first rigorous characterization of Operational Design Domains (ODDs). Unlike in other application sectors (such as self-driving road vehicles) where ODD development is scenario-based, our approach is data-centric: we propose the dimensions along which the parameters that define an ODD can be explicitly captured, using a top-down approach starting from system specifications, and a bottom-up approach starting from detailed ML Model (MLM) designs. Then we give a categorization of the data that ML-based applications can encounter in operation, identifying their system-level relevance and impact. Specifically, we discuss how those data categories are useful to determine: (1) the requirements necessary to drive the design of MLMs; (2) the potential effects on the MLM and higher levels of the system hierarchy; (3) the learning assurance processes that may be needed, and (4) system architectural considerations. We illustrate the underlying concepts with an example of an aircraft flight envelope. The approach in this paper is one of the cornerstones of a future process guidance for development and certification/approval of safety-related aeronautical products implementing Artificial Intelligence (AI), currently being developed through aviation industry-based consensus, jointly by the SAE G-34 Committee for AI in aviation, and EUROCAE WG-114 for AI.

Aeronautical products↗

NASA NTRS1990

Fault injection experiments using FIAT

The results of several experiments conducted using the fault-injection-based automated testing (FIAT) system are presented. FIAT is capable of emulating a variety of distributed system architectures, and it provides the capabilities to monitor system behavior and inject faults for the purpose of experimental characterization and validation of a system's dependability. The experiments consist of exhaustively injecting three separate fault types into various locations, encompassing both the code and data portions of memory images, of two distinct applications executed with several different data values and sizes. Fault types are variations of memory bit faults. The results show that there are a limited number of system-level fault manifestations. These manifestations follow a normal distribution for each fault type. Error detection latencies are found to be normally distributed. The methodology can be used to predict the system-level fault responses during the system design stage.

Barton, James H.↗

NASA NTRS1976

A low light level television system

A proposal was submitted in response to the announcement of opportunities for Skylab 1 involving low light level imaging techniques. While the observational objectives are not necessarily pertinent to cometary experimentation and observation the instrumentation possibly would be, and is potentially available if the proposal is successful. The proposed observations are of natural and induced atmospheric glows and near vehicle aerosol distribution.

Duncan, B. J.↗

NASA NTRS2018

Flux-Pinned Dynamics Model Parameterization and Sensitivity Study

Flux-pinned interfaces for spacecraft are an action-at-a-distance technology that can maintain a passively stable equilibrium between two spacecraft in close-proximity using the physics of magnetic flux pinning. Although flux pinning dynamics have been studied from a material-science perspective and at an interface level, there is a need to better understand the sensitivities and implications of system-level designs on the flux-pinned interface dynamics, especially in designs with multiple magnets and superconductors. These interfaces have highly nonlinear, coupled dynamics that are influenced by physical parameters including but not limited to strength of magnetic field sources, field-cooled position, and superconductor geometry. This paper addresses that gap by codifying parametric terms into an improved dynamics model, which can then be used to simulate the interaction of a multiple-superconductor-multiple-magnet interface. A standard starting point for modeling flux pinning dynamics is Kordyuk’s frozen image model, which defines a geometric mapping between magnetic field sources and their corresponding magnetic point source “images inside the volume of the superconductor.” The frozen image model successfully approximates the characteristics of flux pinning dynamics, but could provide more precise position and orientation predictions with the addition of various physical parameter refinements. The sensitivity of the general flux-pinned dynamics model is studied by varying the physical parameters and simulating the systems level dynamics. A predictive dynamics model is crucial to the maturation of this technology so it can be utilized in spacecraft systems, and this work represents a critical step in the development of that model.

Peck, Mason↗

NASA NTRS1998

A Status of the Advanced Space Transportation Program from Planning to Action

A Technology Plan for Enabling Commercial Space Business was presented at the 48th International Astronautical Congress in Turin, Italy. This paper presents a status of the program's accomplishments. Technology demonstrations have progressed in each of the four elements of the program; (1) Low Cost Technology, (2) Advanced Reusable Technology, (3) Space Transfer Technology and (4) Space Transportation Research. The Low Cost Technology program element is primarily focused at reducing development and acquisition costs of aerospace hardware using a "design to cost" philosophy with robust margins, adapting commercial manufacturing processes and commercial off-the-shelf hardware. The attributes of this philosophy for small payload launch are being demonstrated at the component, sub-system, and system level. The X-34 "Fastrac" engine has progressed through major component and subsystem demonstrations. A propulsion system test bed has been implemented for system-level demonstration of component and subsystem technologies; including propellant tankage and feedlines, controls, pressurization, and engine systems. Low cost turbopump designs, commercial valves and a controller are demonstrating the potential for a ten-fold reduction in engine and propulsion system costs. The Advanced Reusable Technology program element is focused on increasing life through high strength-to-weight structures and propulsion components, highly integrated propellant tanks, automated checkout and health management and increased propulsion system performance. The validation of rocket based combined cycle (RBCC) propulsion is pro,-,ressing through component and subsystem testing. RBCC propulsion has the potential to provide performance margin over an all rocket system that could result in lower gross liftoff weight, a lower propellant mass fraction or a higher payload mass fraction. The Space Transfer Technology element of the program is pursuing technology that can improve performance and dramatically reduce the propellant and structural mass of orbit transfer and deep space systems. Flight demonstration of ion propulsion is progressing towards launch. Ion propulsion is the primary propulsion for Deep Space 1; a flyby of comet West-kohoutek-lkemura and asteroid 3352 McAuliffe. Testing of critical solar-thermal propulsion subsystems have been accomplished and planning is continuing for the flight demonstration of an electrodynamic tether orbit transfer system. The forth and final element of the program, Space Transportation Research, has progressed in several areas of propulsion research. This element of the program is focused at long-term (25 years) breakthrough concepts that could bring launch costs to a factor of one hundred below today's cost or dramatically expand planetary travel and enable interstellar travel.

Lyles, Garry↗

NASA NTRS2019

Overview of NASA's Solar Electric Propulsion Project

NASA is continuing to develop and qualify a state of the art 13 kW-class Advanced Electric Propulsion System (AEPS) for NASA exploration missions through a contract with Aerojet Rocketdyne. An objective of the AEPS project is to empower the US space industry to accelerate the adoption of high power electric propulsion technologies by reducing the risk and uncertainty of integrating Solar Electric Propulsion (SEP) technologies into space flight systems. NASA and AEPS contract has recently initiated engineering hardware testing of the Hall Current Thruster (HCT), Power Processing Unit (PPU), and Xenon Flow Controller (XFC) at both the component and system levels. The successful completion of these tests will provide the required information to advance the AEPS system towards Critical Design Review. In support of the AEPS contract, NASA and JPL have been performing risk reduction activities to address specific concerns of the state of the art higher power Hall thruster propulsion system. These risk reduction activities have included long duration wear testing of the Technology Demonstration Unit (TDU) Hall thruster and cathode hardware, thermal cycling testing of TDU cathode heaters and coils, plasma plume measurements, and investigating PPU design. In addition to NASA propulsion development, the SEP project is developing the Plasma Diagnostic Package (PDP) and the SEP Testbed. The PDP is designed for use in conjunction with a high powered EP system to characterize in-space operation. The SEP Testbed system is developed for demonstration of Abstract: NASA is continuing to develop and qualify a state of the art 13 kW-class Advanced Electric Propulsion System (AEPS) for NASA exploration missions through a contract with Aerojet Rocketdyne. An objective of the AEPS project is to empower the US space industry to accelerate the adoption of high power electric propulsion technologies by reducing the risk and uncertainty of integrating Solar Electric Propulsion (SEP) technologies into space flight systems. NASA and AEPS contract has recently initiated engineering hardware testing of the Hall Current Thruster (HCT), Power Processing Unit (PPU), and Xenon Flow Controller (XFC) at both the component and system levels. The successful completion of these tests will provide the required information to advance the AEPS system towards Critical Design Review. In support of the AEPS contract, NASA and JPL have been performing risk reduction activities to address specific concerns of the state of the art higher power Hall thruster propulsion system. These risk reduction activities have included long duration wear testing of the Technology Demonstration Unit (TDU) Hall thruster and cathode hardware, thermal cycling testing of TDU cathode heaters and coils, plasma plume measurements, and investigating PPU design. In addition to NASA propulsion development, the SEP project is developing the Plasma Diagnostic Package (PDP) and the SEP Testbed. The PDP is designed for use in conjunction with a high powered EP system to characterize in-space operation. The SEP Testbed system is developed for demonstration of an integrated SEP end-to-end system performance. The paper will present an overview of the NASA and the AEPS contract activities and a summary of the associated NASA in-house activities.

Plasma Diagnostics Package↗