Results for “technology accelerator,” — Page 18

NASA NTRS2003

Reliable Transport over SpaceWire for James Webb Space Telescope (JWST) Focal Plane Electronics (FPE) Network

NASA's James Webb Space Telescope (JWST) faces difficult technical and budgetary challenges to overcome before it is scheduled launch in 2010. The Integrated Science Instrument Module (ISIM), shares these challenges. The major challenge addressed in this paper is the data network used to collect, process, compresses and store Infrared data. A total of 114 Mbps of raw information must be collected from 19 sources and delivered to the two redundant data processing units across a twenty meter deployed thermally restricted interface. Further data must be transferred to the solid-state recorder and the spacecraft. The JWST detectors are kept at cryogenic temperatures to obtain the sensitivity necessary to measure faint energy sources. The Focal Plane Electronics (FPE) that sample the detector, generate packets from the samples, and transmit these packets to the processing electronics must dissipate little power in order to help keep the detectors at these cold temperatures. Separating the low powered front-end electronics from the higher-powered processing electronics, and using a simple high-speed protocol to transmit the detector data minimize the power dissipation near the detectors. Low Voltage Differential Signaling (LVDS) drivers were considered an obvious choice for physical layer because of their high speed and low power. The mechanical restriction on the number cables across the thermal interface force the Image packets to be concentrated upon two high-speed links. These links connect the many image packet sources, Focal Plane Electronics (FPE), located near the cryogenic detectors to the processing electronics on the spacecraft structure. From 12 to 10,000 seconds of raw data are processed to make up an image, various algorithms integrate the pixel data Loss of commands to configure the detectors as well as the loss of science data itself may cause inefficiency in the use of the telescope that are unacceptable given the high cost of the observatory. This combination of requirements necessitates a redundant, fault tolerant, high- speed, low mass, low power network with a low Bit error Rate(1E-9- 1E-12). The ISIM systems team performed many studies of the various network architectures that meeting these requirements. The architecture selected uses the Spacewire protocol, with the addition of a new transport and network layer added to implement end-to-end reliable transport. The network and reliable transport mechanism must be implemented in hardware because of the high average information rate and the restriction on the ability of the detectors to buffer data due to power and size restrictions. This network and transport mechanism was designed to be compatible with existing Spacewire links and routers so that existing equipment and designs may be leveraged upon. The transport layer specification is being coordinated with European Space Agency (ESA), Spacewire Working Group and the Consultative Committee for Space Data System (CCSDS) PlK Standard Onboard Interface (SOIF) panel, with the intent of developing a standard for reliable transport for Spacewire. Changes to the protocol presented are likely since negotiations are ongoing with these groups. A block of RTL VHDL that implements a multi-port Spacewire router with an external user interface will be developed and integrated with an existing Spacewire Link design. The external user interface will be the local interface that sources and sinks packets onto and off of the network (Figure 3). The external user interface implements the network and transport layer and handles acknowledgements and re-tries of packets for reliable transport over the network. Because the design is written in RTL, it may be ported to any technology but will initially be targeted to the new Actel Accelerator series (AX) part. Each link will run at 160 Mbps and the power will be about 0.165 Watt per link worst case in the Actel AX.

Rakow, Glenn↗

NASA NTRS2003

Overview of NASA's UEET and TBCC/RTA Programs

A general overview of NASA's Ultra Efficient Engine Technology (UEET) and Turbine Based Combined Cycle (TBCC)/Revolutionary Turbine Accelerator (RTA) is presented. This paper is in viewgraph form.

Shaw, Robert J.↗

NASA NTRS2005

The Vision of Human Spaceflight

First, we live in a world where change is the norm, not the exception. The scientific revolution springing from quantum mechanics yielded new understanding of solid state physics leading to stunning advances in computation, communication, and transportation. Two World Wars and one Cold War introduced massive governmental investment in research and development. The unusual pragmatic and classless entrepreneurship of U.S. society promoted commercialization and innovative marketing of new technology. As a result, the 20th Century experienced a constantly accelerating culture of change. Those societies that accepted and embraced the new capabilities dominated commercially and militarily; those that did not fell behind. I remember when there was no color television, when there were no personal computers, when there was no email, when there was no World Wide Web, when there were no cell phones. Now many of us cannot live without these things. Change has become the measure of success. Our children anticipate the future and do not expect it to look like the past. Secondly, our elementary school students are fascinated by dinosaurs, ghosts, and space. Astronauts create excitement. None question that humans will be in space in their future. They see it every week, even every day, in stories on television. To be an astronaut is considered a legitimate ambition. They see space travel to be an adventure just as our grandparents saw exploring Africa or the polar regions to be an adventure into the unknown. Third, we live in a time when our understanding of the space environment makes us realize that the existence of our species is one large impact away from extinction. We understand that our population explosion is changing our home planet in fundamental ways and that wars over terrestrial resources may be less than two generations away. We feel more connected to our space neighborhood than ever before. Many nations of the world are looking outward toward our Moon in an unprecedented way. A lunar space mission will be launched from somewhere every year for the next decade, at least.

Mendell, Wendell↗

NASA NTRS2015

Improved Convergence and Robustness of USM3D Solutions on Mixed Element Grids (Invited)

Several improvements to the mixed-element USM3D discretization and defect-correction schemes have been made. A new methodology for nonlinear iterations, called the Hierarchical Adaptive Nonlinear Iteration Scheme (HANIS), has been developed and implemented. It provides two additional hierarchies around a simple and approximate preconditioner of USM3D. The hierarchies are a matrix-free linear solver for the exact linearization of Reynolds-averaged Navier Stokes (RANS) equations and a nonlinear control of the solution update. Two variants of the new methodology are assessed on four benchmark cases, namely, a zero-pressure gradient flat plate, a bump-in-channel configuration, the NACA 0012 airfoil, and a NASA Common Research Model configuration. The new methodology provides a convergence acceleration factor of 1.4 to 13 over the baseline solver technology.

Pandya, Mohagna J.↗

NASA NTRS2020

Building the RS-25 Engine for NASA’s Next Generation of Exploration.

NASA is aggressively pursuing a human lunar return to the Moon with the Artemis Program. The Space Launch System (SLS) is critical to the transportation architecture, providing both crew and cargo capability. To accelerate SLS development, NASA settled on space shuttle heritage propulsion technologies. Early missions will use repurposed RS-25 engines from the Shuttle Program adapted to SLS requirements. For future missions, however, NASA and engine contractor Aerojet Rocketdyne are restarting RS-25 production with a goal of using the latest manufacturing technologies to produce an RS-25 variant that will cost at least 30 percent less than the shuttle-era engines developed and flown for almost 30 years. The prospect of restarting the production line on these engines after many years and modifying the engine to reduce cost and better match the needs of the SLS vehicle presented unique challenges and opportunities for NASA and Aerojet Rocketdyne. NASA and AR are now deep into the process of adapting 16 RS-25 engines for the first four SLS Artemis flights and building the first RS-25 “Restart” engines for future Artemis missions. In addition to navigating programmatic, technical, and logistical challenges with the current RS-25 production work, NASA and AR have partnered to pursue new methods of building this engine through advanced manufacturing techniques to further reduce the cost and schedule required to build each RS-25 engine to contribute to the long-term affordability of the SLS vehicle. This presentation will discuss the goals for the restart program, the challenges, and results to date.

Jessica Jean Wood↗

NASA NTRS2024

Tracking Community Building in Open Science

Open Science is enabled by a vibrant community of researchers who regularly engage with the data, from its production to its organization, curation, archiving, dissemination, analysis, and publication. This presentation will examine community building in open science. The NASA Open Science Data Repository (OSDR) makes data available to the public following the FAIR (Findability, Accessibility, Interoperability, and Reusability) principles. OSDR takes open science further with the OS Analysis Working Groups (AWGs) that facilitate community development and promotion. The primary activity of each AWG is to establish and validate analytical processes to generate higher-order data from data housed in OSDR. There are a number of these groups on various topics, including the Animal AWG, Plant AWG, Microbial AWG, Multi-Omics AWG, AI/ML AWG, and the Ames Life Sciences Data Archive (ALSDA) AWG. The international volunteers participating in these AWGs come from academia, citizen science initiatives, industry, and government. They include researchers, principal investigators, professors, trained hobbyists, and students from various domains and disciplines. Anyone may request to join the AWGs, and membership requests are vetted monthly by the group organizers before granting admission. Core to membership is demonstrated expertise through records of training, integrity, work in the professed domain(s), and good community standing. Regular virtual meetings are held for each AWG, with a varying cadence depending on the group's needs and goals. AWG communities share their expertise in research including cutting edge tools, software, frameworks, data formats, and libraries accelerating research collectively. This collaborative approach helps community members cross technology gaps and identify emerging challenges. These diverse communities encompass a wide range of individuals hailing from various sectors within the Science Mission Directorate and beyond. They serve as a means to promote and enhance transparency, accessibility, and inclusion. An annual AWG Symposium brings contributors together in person. Participation in AWGs can be synchronous or asynchronous, with some groups performing most of their work in off hours. Participants gain valuable skills and connections that allow them to add value to their communities and new organizations that they join, resulting in an expanded return on investment for the space life science community. Open science is increasingly a federal mandate and initiatives like NASA's Transform to Open Science and instruments like the Decadal Survey of Biological and Physical Sciences in Space demonstrate the need to carefully consider best practices in this domain. Here, we present greater detail about the makeup and participation metrics of the various AWGs affiliated with OSDR and details of successful peer-reviewed publication campaigns.

Christina M Johnson↗

NASA NTRSDate not supplied

Tracking Community Building in Open Science

Open Science is enabled by a vibrant community of researchers who regularly engage with the data, from its production to its organization, curation, archiving, dissemination, analysis, and publication. This presentation will examine community building in open science. The NASA Open Science Data Repository (OSDR) makes data available to the public following the FAIR (Findability, Accessibility, Interoperability, and Reusability) principles. OSDR takes open science further with the OS Analysis Working Groups (AWGs) that facilitate community development and promotion. The primary activity of each AWG is to establish and validate analytical processes to generate higher-order data from data housed in OSDR. There are a number of these groups on various topics, including the Animal AWG, Plant AWG, Microbial AWG, Multi-Omics AWG, AI/ML AWG, and the Ames Life Sciences Data Archive (ALSDA) AWG. The international volunteers participating in these AWGs come from academia, citizen science initiatives, industry, and government. They include researchers, principal investigators, professors, trained hobbyists, and students from various domains and disciplines. Anyone may request to join the AWGs, and membership requests are vetted monthly by the group organizers before granting admission. Core to membership is demonstrated expertise through records of training, integrity, work in the professed domain(s), and good community standing. Regular virtual meetings are held for each AWG, with a varying cadence depending on the group's needs and goals. AWG communities share their expertise in research including cutting edge tools, software, frameworks, data formats, and libraries accelerating research collectively. This collaborative approach helps community members cross technology gaps and identify emerging challenges. These diverse communities encompass a wide range of individuals hailing from various sectors within the Science Mission Directorate and beyond. They serve as a means to promote and enhance transparency, accessibility, and inclusion. An annual AWG Symposium brings contributors together in person. Participation in AWGs can be synchronous or asynchronous, with some groups performing most of their work in off hours. Participants gain valuable skills and connections that allow them to add value to their communities and new organizations that they join, resulting in an expanded return on investment for the space life science community. Open science is increasingly a federal mandate and initiatives like NASA's Transform to Open Science and instruments like the Decadal Survey of Biological and Physical Sciences in Space demonstrate the need to carefully consider best practices in this domain. Here, we present greater detail about the makeup and participation metrics of the various AWGs affiliated with OSDR and details of successful peer-reviewed publication campaigns.

Christina M Johnson↗

NASA NTRS2011

Dynamic Testing of the NASA Hypersonic Project Combined Cycle Engine Testbed for Mode Transition Experiments

NASA is interested in developing technology that leads to more routine, safe, and affordable access to space. Access to space using airbreathing propulsion systems has potential to meet these objectives based on Airbreathing Access to Space (AAS) system studies. To this end, the NASA Fundamental Aeronautics Program (FAP) Hypersonic Project is conducting fundamental research on a Turbine Based Combined Cycle (TBCC) propulsion system. The TBCC being studied considers a dual flow-path inlet system. One flow-path includes variable geometry to regulate airflow to a turbine engine cycle. The turbine cycle provides propulsion from take-off to supersonic flight. The second flow-path supports a dual-mode scramjet (DMSJ) cycle which would be initiated at supersonic speed to further accelerate the vehicle to hypersonic speed. For a TBCC propulsion system to accelerate a vehicle from supersonic to hypersonic speed, a critical enabling technology is the ability to safely and effectively transition from the turbine to the DMSJ-referred to as mode transition. To experimentally test methods of mode transition, a Combined Cycle Engine (CCE) Large-scale Inlet testbed was designed with two flow paths-a low speed flow-path sized for a turbine cycle and a high speed flow-path designed for a DMSJ. This testbed system is identified as the CCE Large-Scale Inlet for Mode Transition studies (CCE-LIMX). The test plan for the CCE-LIMX in the NASA Glenn Research Center (GRC) 10- by 10-ft Supersonic Wind Tunnel (10x10 SWT) is segmented into multiple phases. The first phase is a matrix of inlet characterization (IC) tests to evaluate the inlet performance and establish the mode transition schedule. The second phase is a matrix of dynamic system identification (SysID) experiments designed to support closed-loop control development at mode transition schedule operating points for the CCE-LIMX. The third phase includes a direct demonstration of controlled mode transition using a closed loop control system developed with the data obtained from the first two phases. Plans for a fourth phase include mode transition experiments with a turbine engine. This paper, focusing on the first two phases of experiments, presents developed operational and analysis tools for streamlined testing and data reduction procedures.

Source record↗

NASA NTRS2004

Recent Progress on the VASIMR Engine

The development of the Variable Specific Impulse Magnetoplasma Rocket (VASIMR) was initiated in the late 1970s to address a critical requirement for fast, high-power interplanetary space transportation. Its high-power and electrodeless design arises from the use of radio frequency (RF) waves to create and accelerate plasma in a magnetic nozzle. While not being a fusion rocket, it borrows heavily from that technology and takes advantage of the natural topology of open-ended magnetic systems. In addition the system lends itself well for Constant Power Throttling (CPT,) an important ability to vary thrust and specific impulse, over a wide operational range, while maintaining maximum power. This allows in-flight mission-optimization of thrust and specific impulse to enhance performance and reduce trip time. A NASA-led, research team, involving industry, academia and government facilities is pursuing the development of this concept in the United States. The technology can be validated, in the near term, in venues such as the International Space Station, where it can also serve as both a drag compensation device and a plasma contactor for the orbital facility. Recent advances in the development of this technology involve the demonstration of efficient propellant utilization in a flowing helicon plasma discharge as well as the experimental verification of single-pass ion acceleration, as predicted by theory I, by coupling RF power to the plasma through ion cyclotron resonance. This paper outlines these and other progress in our understanding of VASIMR physics and presents the concepts for its potential application in NASA's new vision of space exploration.

Chang-Diaz, F. R.↗

NASA NTRS1997

Magnetohydrodynamics Accelerator Research Into Advanced Hypersonics (MARIAH)

This report documents the activities, results, conclusions and recommendations of the Magnetohydrodynamics Accelerator Research Into Advanced Hypersonics (MARIAH) Project in which the use of magnetohydrodynamics (MHD) technology is investigated for its applicability to augment hypersonic wind tunnels. The long range objective of this investigation is to advance the development of ground test facilities to support the development of hypervelocity flight vehicles. The MHD accelerator adds kinetic energy directly to the wind tunnel working fluid, thereby increasing its Mach number to hypervelocity levels. Several techniques for MHD augmentation, as well as other physical characteristics of the process are studied to enhance the overall performance of hypersonic wind tunnel design. Specific recommendations are presented to improve the effectiveness of ground test facilities. The work contained herein builds on nearly four decades of research and experimentation by the aeronautics ground test and evaluation community, both foreign and domestic.

Micheletti, David A.↗

NASA NTRS1997

Magnetohydrodynamics Accelerator Research into Advanced Hypersonics (MARIAH)

This report documents the activities, results, conclusions and recommendations of the Magnetohydrodynamics Accelerator Research Into Advanced Hypersonics (MARIAH) Project in which the use of magnetohydrodynamics (MHD) technology is investigated for its applicability to augment hypersonic wind tunnels. The long range objective of this investigation is to advance the development of ground test facilities to support the development of hypervelocity flight vehicles. The MHD accelerator adds kinetic energy directly to the wind tunnel working fluid, thereby increasing its Mach number to hypervelocity levels. Several techniques for MHD augmentation, as well as other physical characteristics of the process are studied to enhance the overall performance of hypersonic wind tunnel design. Specific recommendations are presented to improve the effectiveness of ground test facilities. The work contained herein builds on nearly four decades of research and experimentation by the aeronautics ground test and evaluation community, both foreign and domestic.

Baughman, Jack A.↗

NASA NTRS2018

Inductive Pulsed Plasma Thruster Development Testing at NASA-MSFC

The inductive pulsed plasma thruster (IPPT) is an electromagnetic plasma accelerator that has been identified in NASA roadmaps as an enabling propulsion technology for some niche low-power missions and for high-power in-space propulsion needs. The IPPT is an electrodeless space propulsion device where a capacitor is charged to an initial voltage and then discharged producing a high current pulse through a coil. The field produced by this pulse ionizes propellant, inductively driving current in a plasma located near the face of the coil. Once the plasma is formed it can be accelerated and expelled at a high exhaust velocity by the electromagnetic Lorentz body force arising from the interaction of the induced plasma current and the magnetic field produced by the current in the coil. Thrusters of this type possess many demonstrated and potential benefits that make them worthy of continued investigation. The electrodeless nature of these thrusters eliminates the lifetime and contamination issues associated with electrode erosion in conventional electric thrusters. Also, a wider variety of propellants are accessible when compatibility with metallic electrodes in no longer an issue. IPPTs have been successfully operated using propellants like ammonia, hydrazine, and CO2, and there is no fundamental reason why they would not operate on other in situ propellants like H2O. It is well-known that pulsed accelerators can maintain constant specific impulse (I(sub sp)) and thrust efficiency (η(sub t)) over a wide range of input power levels by adjusting the pulse rate to hold the discharge energy per pulse constant. It has also been demonstrated that an inductive pulsed plasma thruster can operate in a regime where η(sub t) is relatively constant over a wide range of I(sub sp) values (3000-8000 s). Finally, thrusters in this class have operated in single-pulse mode at high energy per pulse, and by increasing the pulse rate they offer the potential to process very high levels of power using a single thruster. There has been significant previous research on IPPTs designed around a planar-coil (flat-plate) geometry. The most notable of these was the Pulsed Inductive Thruster (PIT), with the PIT MkV presently representing the state of- the-art in pulsed high-power IPPT technological development. In this paper, we focus on two planar-geometry devices that operate at significantly different power levels. Most work performed at NASA-Marshall Space Flight Center (MSFC) has, to date, focused on lower power thruster operation (≈ 10s to 100s of J/pulse, up to 2-2.5 kW average power throughput) and previously described in Refs. [5,6]. The most recent work aimed to assemble a device that could be tested in cyclic mode on a thrust-stand, and which could augment the existing data set for IPPTs. In addition, the thruster was designed to serve as a test-bed for solid state switching circuitry and pulsed gas valves, with the modular design of the device allowing for variation in or upgrades to test configuration. Recently, MSFC obtained on loan from the Georgia Institute of Technology (Atlanta, GA) the PIT MkVI, successor to the PIT MkV. The MkV and MkVI are similar in design with much of the hardware from the former, specifically the capacitors and spark-gap switches, being reused in the latter. The coil is simliar in geometry but has bent copper rods used in the latest iteration in place of the Litz wire windings found in the MkV. The MkVI master switch for the spark gaps is located in the vacuum chamber contained within a sealed, pressurized vessel fastened to the back of the thruster. This is different from the MkV where many capacitor charging lines and spark gap-triggering delay lines ran to the thruster from a master trigger located outside the vacuum chamber. The MkVI was damaged during testing soon after its fabrication was completed. The thruster arrived at MSFC still-damaged and mostly disassembled into many individual pieces. The device has been repaired, with a few additional design changes implemented after discussions with the late Prof. Lovberg regarding the initial testing results and issues encountered.

Polzin, Kurt A.↗

NASA NTRS2017

Low and High-Power Inductive Pulsed Plasma Thruster Development Testing at NASA-MSFC

The inductive pulsed plasma thruster (IPPT) is an electromagnetic plasma accelerator that has been identified in NASA roadmaps as an enabling propulsion technology for some niche low-power missions and for high-power in-space propulsion needs. The IPPT is an electrodeless space propulsion device where a capacitor is charged to an initial voltage and then discharged producing a high current pulse through a coil. The field produced by this pulse ionizes propellant, inductively driving current in a plasma located near the face of the coil. Once the plasma is formed it can be accelerated and expelled at a high exhaust velocity by the electromagnetic Lorentz body force arising from the interaction of the induced plasma current and the magnetic field produced by the current in the coil. Thrusters of this type possess many demonstrated and potential benefits that make them worthy of continued investigation. The electrodeless nature of these thrusters eliminates the lifetime and contamination issues associated with electrode erosion in conventional electric thrusters. Also, a wider variety of propellants are accessible when compatibility with metallic electrodes in no longer an issue. IPPTs have been successfully operated using propellants like ammonia, hydrazine, and CO2, and there is no fundamental reason why they would not operate on other in situ propellants like H2O. It is well-known that pulsed accelerators can maintain constant specific impulse (I(sub sp)) and thrust efficiency (eta(sub t)) over a wide range of input power levels by adjusting the pulse rate to hold the discharge energy per pulse constant. It has also been demonstrated that an inductive pulsed plasma thruster can operate in a regime where eta(sub t) is relatively constant over a wide range of I(sub sp) values (3000-8000 s). Finally, thrusters in this class have operated in single-pulse mode at high energy per pulse, and by increasing the pulse rate they offer the potential to process very high levels of power using a single thruster. There has been significant previous research on IPPTs designed around a planar-coil (flat-plate) geometry. The most notable of these was the Pulsed Inductive Thruster (PIT), with the PIT MkV presently representing the state-of- the-art in pulsed high-power IPPT technological development. In this paper, we focus on two planar-geometry devices that operate at significantly different power levels. Most work performed at NASA-Marshall Space Flight Center (MSFC) has, to date, focused on lower power thruster operation (approx. = 10s to 100s of J/pulse, up to 2-2.5 kW average power throughput) and previously described. The most recent work aimed to assemble a device that could be tested in cyclic mode on a thrust-stand, and which could augment the existing data set for IPPTs. In addition, the thruster was designed to serve as a test-bed for solid state switching circuitry and pulsed gas valves, with the modular design of the device allowing for variation in or upgrades to test configuration. Recently, MSFC obtained on loan from the Georgia Institute of Technology (Atlanta, GA) the PIT MkVI, successor to the PIT MkV. The MkV and MkVI are similar in design with much of the hardware from the former, specifically the capacitors and spark-gap switches, being reused in the latter. The coil is similar in geometry but has bent copper rods used in the latest iteration in place of the Litz wire windings found in the MkV. The MkVI master switch for the spark gaps is located in the vacuum chamber contained within a sealed, pressurized vessel fastened to the back of the thruster. This is different from the MkV where many capacitor charging lines and spark gap-triggering delay lines ran to the thruster from a master trigger located outside the vacuum chamber. The MkVI was damaged during testing soon after its fabrication was completed. The thruster arrived at MSFC still-damaged and mostly disassembled into many individual pieces. The device has been repaired, with a few additional design changes implemented after discussions with the late Prof. Lovberg regarding the initial testing results and issues encountered. In the present work, we present results from testing of both the small IPPT and the larger MkVI thruster. The smaller device (Fig. 1) is tested on a thrust stand on multiple gases to demonstrate its capability to operate in a repetition-rate mode and serve as a IPPT technology-development testbed. The larger MkVI (Fig. 2) is operated for the first time in its newly reconstituted state, demonstrating full-power pulsed operation and, for the first time, repetition-rate operation of a high-power IPPT. The additional upgrades required for synchronous operation of all the pulsed systems in single-pulse and repetition-rate mode are described in detail.

Polzin, Kurt A.↗

NASA NTRS2008

Zero CTE Glass in the Hubble Space Telescope

Orbiting high above the turbulence of the Earth's atmosphere, the Hubble Space Telescope (HST) has provided breathtaking views of astronomical objects never before seen in such detail. The steady diffraction-limited images allow this medium-size telescope to reach faint galaxies fainter than 30th stellar magnitude. Some of these galaxies are seen as early as 2 billion years after the Big Bang in a 13.7 billion year old universe. Up until recently, astronomers assumed that all of the laws of physics and astronomy applied back then as they do today. Now, using the discovery that certain supernovae are "standard candles," astronomers have found that the universe is expanding faster today than it was back then: the universe is accelerating in its expansion. The Hubble Space Telescope is a two-mirror Ritchey-Chretien telescope of 2.4m aperture in low earth orbit. The mirrors are made of Ultra Low Expansion (ULE) glass by Corning Glass Works. This material allows rapid figuring and outstanding performance in space astronomy applications. The paper describes how the primary mirror was mis-figured in manufacturing and later corrected in orbit. Outstanding astronomical images taken over the last 17 years show how the application of this new technology has advanced our knowledge of the universe. Not only has the acceleration of the expansion been discovered, the excellent imaging capability of HST has allowed gravitational lensing to become a tool to study the distribution of dark matter and dark energy in distant clusters of galaxies. The HST has touched practically every field of astronomy enabling astronomers to solve many long-standing puzzles. It will be a long time until the end of the universe when the density is near zero and all of the stars have long since evaporated. It is remarkable that humankind has found the technology and developed the ability to interpret the measurements in order to understand this dramatic age we live in.

Wood, H. John↗

NASA NTRS2003

International Space Station Microgravity Analytical Model Correlation And Update

The acceleration environment aboard the completed International Space Station (ISS) is a key resource for scientific and technological endeavors. Hardware verification activIties and early measurements indicate that the ISS is well on the way of meeting these "Assembly Complete" "microgravity" provisions, however, the simulation models that compute these accelerations have, to date, lacked the high degree of empirical validation typical of standard aerospace industry practices. Assembly stage, on-orbit measurements are used to address this shortcoming and to develop higher confidence in the simulation models. The Phase I correlation results show the analyses to be consistently conservative, producing higher than measured levels. The 25 to 30% greater quasi-steady computations are deemed acceptable for verification. Updates are made to localized structural dynamic and vibroacoustic parameters that reduce responses in selected one-third octave bands by almost 50%. These models are then used for the Assembly Complete verification analysis which concludes that the ISS vehicle meets the ISS microgravity requirements with minor reservations. Two of the sixteen rack are marginally non-compliant in the quasi-steady regime, and operational constraints are needed on the U. S. Lab and ESA APM vacuum resource vents, and the Russian Resistive Exercise Device in the structural dynamic regime.

DelBasso, Steve↗

NASA NTRS1979

Analysis of an Arctic Polesitter

The concept and rationale are presented and the fundamental dynamical requirements set forth for a spacecraft that remains stationary in space above the North or South Pole of the earth for an extended period of time. The mathematical basis and acceleration characteristics are shown. Performance capability using present day Ion Drive technology is evaluated in terms of stay time at the pole and imaging resolution as a function of viewing distance. The analysis shows that a Polesitter spacecraft can be maintained without difficulty for one or two years at several lunar distances from the earth, admitting large resolution visual imagery and some less useful measurements in the infra-red regime. Microwave measurements are not practical using today's technology. Sensitivity calculations show that substantial improvement in performance capability must await major advances in available technology.

Driver, J. M.↗

NASA NTRS1980

Solar/hydrogen systems assessment. Volume 1: Solar/hydrogen systems for the 1985 - 2000 time frame

Opportunities for commercialization of systems capable of producing hydrogen from solar energy were studied. The hydrogen product costs that might be achieved by the four selected candidate systems was compared with the pricing structure and practices of the commodity gas market. Subsequently, product cost and market price match was noted to exist in the small user sector of the hydrogen marketplace. Barriers to and historical time lags in, commercialization of new technologies are reviewed. Recommendations for development and demonstration programs designed to accelerate the commercialization of the candidate systems are presented.

Foster, R. W.↗

NASA NTRS1991

Experimental millimeter-wave personal satellite communications system

Communications Research Laboratory (CRL) has investigated an advanced millimeter (mm)-wave satellite communications system for personal use. Experiments in mm-wave personal satellite communication are to be conducted for 3 years using Japan's Engineering Test Satellite VI (ETS-VI). This paper describes an experimental mm-wave (43/38 GHz) personal satellite communication system, including an onboard transponder and an earth terminal. The on-board transponder is almost completed, and the ground experiment system is still in the design stage. The transponder employs advanced mm-wave solid state technology. It uses 38 GHz high power solid state amplifiers to accelerate the development of mm-wave solid state devices which are indispensable to personal earth terminals. The transponder consists of a 43 GHz receiver with a built-in low noise amplifier, an IF filter section with very narrow bandwidth to improve the carrier-to-noise power ratio of the weak personal communication signal, and two high power amplifiers using newly developed high power Gallium Arsenide (GaAs) metal-semiconductor field effect transistors (MESFETs).

Suzuki, Yoshiaki↗