NASA Space Shuttle Technology Conference: Structures and Materials - Volume 2
NASA conference on space shuttles structural design, thermal protection, and materials technology - Vol. 2
Source record↗
SEARCH · Search NASA
Results for “thermal protection materials”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ultrahigh Temperature Ceramics for Thermal Protection of Next Generation Space Vehicles
Materials with improved properties are needed for thermal protection of next generation space vehicles. Sharp leading edges on these vehicles will have to withstand exposure to high temperatures (> 2200 C or 4000 F) and severe thermal cycling in both neutral and oxidizing environments. These extreme conditions will require materials that possess superior oxidation resistance, low creep, and excellent thermal shock properties. This presentation will first discuss the system requirements for thermal protection of advanced space vehicles and then show how they are driving development of new materials systems. The presentation will focus on ultrahigh temperature ceramics (UHTCs) that are promising candidates for such applications. ZrB2 and HfB2 and composites of those ceramics with SiC are two particular families of UHTCs that are currently under development for sharp leading edges. These ceramics are appealing because their melting temperatures are 3245 C (5873 F) for ZrB2 and 3380 C (6116 F) for HfB2 and because they may form protective, oxidation resistant coatings in use. The mechanical properties of the UHTCs are strongly dependent on phase purity and the processing route used to make them, both of which factors are being actively investigated. For example, oxide impurities could form glassy grain boundary phases that soften at high temperatures and make the ceramic susceptible to creep deformation. Results from scanning and transmission electron microscopic studies of the UHTCs have shown how their processing can be improved to give better properties. This presentation will discuss the UHTC characterization results in some detail, focusing particularly on the structure and composition of the ceramic grain boundaries. The presentation will conclude with some remarks on how the properties of these promising UHTCs can be further improved and how they might be made more economically.
Loehman, R. E.↗
Design of a Thermal and Micrometeorite Protection System for an Unmanned Lunar Cargo Lander
The first vehicles to land on the lunar surface during the establishment phase of a lunar base will be unmanned lunar cargo landers. These landers will need to be protected against the hostile lunar environment for six to twelve months until the next manned mission arrives. The lunar environment is characterized by large temperature changes and periodic micrometeorite impacts. An automatically deployable and reconfigurable thermal and micrometeorite protection system was designed for an unmanned lunar cargo lander. The protection system is a lightweight multilayered material consisting of alternating layers of thermal and micrometeorite protection material. The protection system is packaged and stored above the lander common module. After landing, the system is deployed to cover the lander using a system of inflatable struts that are inflated using residual fuel (liquid oxygen) from the fuel tanks. Once the lander is unloaded and the protection system is no longer needed, the protection system is reconfigured as a regolith support blanket for the purpose of burying and protecting the common module, or as a lunar surface garage that can be used to sort and store lunar surface vehicles and equipment. A model showing deployment and reconfiguration of the protection system was also constructed.
Hernandez, Carlos A.↗
Ultra-High Temperature Ceramic (UHTC) Development
During the last decade, NASA Ames has been developing new, Ultra-High Temperature Ceramic (UHTC) materials for Thermal Protection Systems applications. The UHTC s are a family of materials including compositions of HfE32 and ZrB2 with a Sic second phase. A collaboration with Glenn was recently initiated to evaluate the viability of some UHTC materials that had been produced by an outside vendor for use in gas turbine en,@ne environments. Results from this collaboration have indicated that compositions based on HfB2 show the most promise, among the UHTC compositions evaluated, for use in these environments. Work at ARC has been initiated to fabricate these materials in-house and evaluate methods of improving their properties for use in engine environments.
Johnson, Sylvia↗
External Tank - The Structure Backbone
The External Tank forms the structural backbone of the Space Shuttle in the launch configuration. Because the tank flies to orbital velocity with the Space Shuttle Orbiter, minimization of weight is mandatory, to maximize payload performance. Choice of lightweight materials both for structure and thermal conditioning was necessary. The tank is large, and unique manufacturing facilities, tooling, handling, and transportation operations were required. Weld processes and tooling evolved with the design as it matured through several block changes, to reduce weight. Non Destructive Evaluation methods were used to assure integrity of welds and thermal protection system materials. The aluminum-lithium alloy was used near the end of the program and weld processes and weld repair techniques had to be refined. Development and implementation of friction stir welding was a substantial technology development incorporated during the Program. Automated thermal protection system application processes were developed for the majority of the tank surface. Material obsolescence was an issue throughout the 40 year program. The final configuration and tank weight enabled international space station assembly in a high inclination orbit allowing international cooperation with the Russian Federal Space Agency. Numerous process controls were implemented to assure product quality, and innovative proof testing was accomplished prior to delivery. Process controls were implemented to assure cleanliness in the production environment, to control contaminants, and to preclude corrosion. Each tank was accepted via rigorous inspections, including non-destructive evaluation techniques, proof testing, and all systems testing. In the post STS-107 era, the project focused on ascent debris risk reduction. This was accomplished via stringent process controls, post flight assessment using substantially improved imagery, and selective redesigns. These efforts were supported with a number of test programs to simulate combined environments. Processing improvements included development and use of low spray guns for foam application, additional human factors considerations for production, use of high fidelity mockups during hardware processing with video review, improved tank access, extensive use of non destructive evaluation, and producibility enhancements. Design improvements included redesigned bipod fittings, a bellows heater, a feedline camera active during ascent flight, removal of the protuberance airload ramps, redesigned ice frost ramps, and titanium brackets replaced aluminum brackets on the liquid oxygen feedline. Post flight assessment improved due to significant addition of imagery assets, greatly improving situational awareness. The debris risk was reduced by two orders of magnitude. During this time a major natural disaster was overcome when Katrina damaged the manufacturing facility. Numerous lessons from these efforts are documented within the paper.
Welzyn, Kenneth↗
Reentry Thermal Analysis of a Generic Crew Exploration Vehicle Structure
Comparative studies were performed on the heat-shielding characteristics of honeycomb-core sandwich panels fabricated with different materials for possible use as wall panels for the proposed crew exploration vehicle. Graphite/epoxy sandwich panel was found to outperform aluminum sandwich panel under the same geometry due to superior heat-shielding qualities and lower material density. Also, representative reentry heat-transfer analysis was performed on the windward wall structures of a generic crew exploration vehicle. The Apollo low Earth orbit reentry trajectory was used to calculate the reentry heating rates. The generic crew exploration vehicle has a graphite/epoxy composite honeycomb sandwich exterior wall and an aluminum honeycomb sandwich interior wall, and is protected with the Apollo thermal protection system ablative material. In the thermal analysis computer program used, the TPS ablation effect was not yet included; however, the results from the nonablation heat-transfer analyses were used to develop a "virtual ablation" method to estimate the ablation heat loads and the thermal protection system recession thicknesses. Depending on the severity of the heating-rate time history, the virtual ablation period was found to last for 87 to 107 seconds and the ablation heat load was estimated to be in the range of 86 to 88 percent of the total heat load for the ablation time period. The thermal protection system recession thickness was estimated to be in the range of 0.08 to 0.11 inches. For the crew exploration vehicle zero-tilt and 18-degree-tilt stagnation points, thermal protection system thicknesses of h = {0.717, 0.733} inches were found to be adequate to keep the substructural composite sandwich temperature below the limit of 300 F.
Ko, William L.↗
An Analysis of the Selected Materials Used in Step Measurements During Pre-Fits of Thermal Protection System Tiles and the Accuracy of Measurements Made Using These Selected Materials
The goal of this research project was be to compare and contrast the selected materials used in step measurements during pre-fits of thermal protection system tiles and to compare and contrast the accuracy of measurements made using these selected materials. The reasoning for conducting this test was to obtain a clearer understanding to which of these materials may yield the highest accuracy rate of exacting measurements in comparison to the completed tile bond. These results in turn will be presented to United Space Alliance and Boeing North America for their own analysis and determination. Aerospace structures operate under extreme thermal environments. Hot external aerothermal environments in high Mach number flights lead to high structural temperatures. The differences between tile heights from one to another are very critical during these high Mach reentries. The Space Shuttle Thermal Protection System is a very delicate and highly calculated system. The thermal tiles on the ship are measured to within an accuracy of .001 of an inch. The accuracy of these tile measurements is critical to a successful reentry of an orbiter. This is why it is necessary to find the most accurate method for measuring the height of each tile in comparison to each of the other tiles. The test results indicated that there were indeed differences in the selected materials used in step measurements during prefits of Thermal Protection System Tiles and that Bees' Wax yielded a higher rate of accuracy when compared to the baseline test. In addition, testing for experience level in accuracy yielded no evidence of difference to be found. Lastly the use of the Trammel tool over the Shim Pack yielded variable difference for those tests.
Kranz, David William↗
Performance evaluation of ''Thermo-lag'' material for entry heat protection of advanced manned spacecraft Material development report, 1 Oct. 1962 - 1 Apr. 1963
Performance evaluation of Thermo-lag material for advanced manned spacecraft reentry heat protection
HIGH TEMPERATURE MATERIAL↗
Results of tests of K5NA and a revised formulation of EPDM/cork patch material in MSFC Hot Gas Facility
During prelaunch procedures at Kennedy Space Center some of the EPDM Thermal Protection System material was damaged on the Solid Rocket Booster stiffener stubs. The preferred solution was to patch the damaged areas with a cork-filled epoxy patching compound. Before this was done, however, it was requested that this patching technique be checked out by testing it in the MSFC Hot Gas Facility. Two tests were run in the HFG in 1980. The results showed the patch material to be adequate. Since that time, the formulation of the cork-filled epoxy material has been changed. It became necessary to retest this concept to be sure that the new material is as good as or better than the original material. In addition to the revised formulation material, tests were also made using K5NA as the patch material. The objectives of the tests reported herein were to: (1) compare the thermal performance of the original and the new cork-filled epoxy formulations, and (2) compare the K5NA closeout material to these epoxy materials. Material specifications are also discussed.
Dean, W. G.↗
Modeling instrumented test articles for Plasmatron X aerothermal environment
This work discusses the ablative response of thermal protection system materials when exposed to aerothermal environments. It focuses on modeling instrumented test article assemblies tested in the Plasmatron X inductively coupled plasma wind tunnel. For this purpose, as the samples are mounted to a water-cooled arm using numerous assembly components and are embedded with thermocouples for in-depth temperature measurements, the variation in ablative response of the samples as a result of these components is studied. The aerothermal boundary conditions for Plasmatron X are obtained for hypersonic flight-relevant conditions using the multi-physics aerothermal framework built at the University of Illinois at Urbana-Champaign. For simulating the material response, a material response code, Porous Material Analysis Toolbox based on OpenFOAM (PATO) is used. In PATO, numerous configurations and materials of thermocouples were studied. The optimal configuration for obtaining temperature measurements with minimal error using embedded thermocouples was found to be the U-shaped Type S, 30 American wire gauge thermocouple configuration.
Thermal Protection Systems↗
Modeling instrumented test articles for Plasmatron X aerothermal environment
This work discusses the ablative response of thermal protection system materials when exposed to aerothermal environments. It focuses on modeling instrumented test article assemblies tested in the Plasmatron X inductively coupled plasma wind tunnel. For this purpose, as the samples are mounted to a water-cooled arm using numerous assembly components and are embedded with thermocouples for in-depth temperature measurements, the variation in ablative response of the samples as a result of these components is studied. The aerothermal boundary conditions for Plasmatron X are obtained for hypersonic flight-relevant conditions using the multi-physics aerothermal framework built at the University of Illinois at Urbana-Champaign. For simulating the material response, a material response code, Porous Material Analysis Toolbox based on OpenFOAM (PATO) is used. In PATO, numerous configurations and materials of thermocouples were studied. The optimal configuration for obtaining temperature measurements with minimal error using embedded thermocouples was found to be the U-shaped Type S, 30 American wire gauge thermocouple configuration.
Thermal Protection Systems↗
An Overview of Combined CFD and Material Response Simulations of Arcjet Experiments in Support of the Mars Sample Return Earth Entry System
This presentation will also include a top-level overview of the CFD/material response arcjet simulation process. A discussion will be made on the best-practices for running CFD solutions of arcjet experiments including how to determine the inflow conditions for the CFD solution from the arc heater settings. The required inputs to the material response solver will be presented, as well as a discussion of how they can be extracted from the CFD solution. Grid requirements for both the CFD and material response solver will be explored.
Thermal protection↗
DESIGN AND TESTING OF DIMES CARBON ABLATION RODS IN THE DIII-D TOKAMAK
We present the design of ATJ graphite rods developed for ablation experiments under high heat flux (up to 50 MW/m2) in the lower divertor of the DIII-D tokamak, a magnetic plasma confinement device. This work is motivated by the need to test ablation models relevant to carbon-based thermal shields used in high-speed spacecraft atmospheric entries, where the heat fluxes encountered can be comparable to those achieved in the DIII-D divertor plasma. Several different designs for the flowfacing side of the rod are analyzed, including "sharp nose," "blunt," and "concave". The last shape is studied for its potential to lower heat fluxes at the rod surface by increased radiation from trapped neutrals and reduced parallel plasma pressure. We also analyze the possibility of applying a thin (approximately 30 microns) layer of silicon carbide (SiC) to the exposed part of several carbon ablation rods to benchmark its erosion calculations and lifetime predictions. Such calculations are of interest as SiC represents a promising material for both thermal protection systems (TPS) and a fusion plasma-facing material (PFM). Preliminary results from the DIII-D rod ablation experiments are also discussed.
Orlov, Dmitri M.↗
Development and Design Application of Rigidized Surface Insulation Thermal Protection Systems, Volume 1
Materials and design technology of the all-silica LI-900 rigid surface insulation (RSI) thermal protection system (TPS) concept for the shuttle spacecraft is presented. All results of contract development efforts are documented. Engineering design and analysis of RSI strain arrestor plate material selections, sizing, and weight studies are reported. A shuttle prototype test panel was designed, analyzed, fabricated, and delivered. Thermophysical and mechanical properties of LI-900 were experimentally established and reported. Environmental tests, including simulations of shuttle loads represented by thermal response, turbulent duct, convective cycling, and chemical tolerance tests are described and results reported. Descriptions of material test samples and panels fabricated for testing are included. Descriptions of analytical sizing and design procedures are presented in a manner formulated to allow competent engineering organizations to perform rational design studies. Results of parametric studies involving material and system variables are reported. Material performance and design data are also delineated.
Source record↗
Material Response Modeling of Ablative Thermal Protection Systems using PATO
Developing thermal protection systems (TPS) for future space vehicles involves an extensive design and test cycle. A key component of the cycle is determining margins for a safe design that rely on confidence in the performance of the TPS. Predicting the complicated multiphysics phenomena that occur during atmospheric entry requires high-fidelity modeling tools. To this end, the Porous-material Analysis Toolbox based on OpenFOAM (PATO) has been developed. PATO is an open-source software for computing material response of reactive porous materials submitted to high-temperature environments. Recent applications of PATO include computation of the full heatshield 3D material response from the Mars Science Laboratory atmospheric entry and ablation during arc jet testing. Current efforts are underway to loosely couple PATO with other discipline specialized codes including hypersonic computational fluid dynamics (CFD) to assess the effects of pyrolysis-gas blowing into the boundary layer and computational solid mechanics to address modeling of mechanical erosion. Surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation are also being added.
Thermal Protection Systems↗
Material Response Modeling of Ablative Thermal Protection Systems using PATO
Developing thermal protection systems (TPS) for future space vehicles involves an extensive design and test cycle. A key component of the cycle is determining margins for a safe design that rely on confidence in the performance of the TPS. Predicting the complicated multiphysics phenomena that occur during atmospheric entry requires high-fidelity modeling tools. To this end, the Porous-material Analysis Toolbox based on OpenFOAM (PATO) has been developed. PATO is an open-source software for computing material response of reactive porous materials submitted to high-temperature environments. Recent applications of PATO include computation of the full heatshield 3D material response from the Mars Science Laboratory atmospheric entry and ablation during arc jet testing. Current efforts are underway to loosely couple PATO with other discipline specialized codes including hypersonic computational fluid dynamics (CFD) to assess the effects of pyrolysis-gas blowing into the boundary layer and computational solid mechanics to address modeling of mechanical erosion. Surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation are also being added.
Thermal Protection Systems↗
Studies of Carbon Nanotubes
The fellowship experience for this summer for 2004 pertains to carbon nanotube coatings for various space-related applications. They involve the following projects: (a) EMI protection films from HiPco-polymers, and (b) Thermal protection nanosilica materials. EMI protection films are targeted to be eventually applied onto casings of laptop computers. These coatings are composites of electrically-conductive SWNTs and compatible polymers. The substrate polymer will be polycarbonate, since computer housings are typically made of carbon composites of this type of polymer. A new experimental copolymer was used last year to generate electrically-conductive and thermal films with HiPco at 50/50 wt/wt composition. This will be one of the possible formulations. Reference films will be base polycarbonate and neat HiPco onto polycarbonate films. Other coating materials that will be tried will be based on HiPco composites with commercial enamels (polyurethane, acrylic, polyester), which could be compatible with the polycarbonate substrate. Nanosilica fibers are planned for possible use as thermal protection tiles on the shuttle orbiter. Right now, microscale silica is used. Going to the nanoscale will increase the surface-volume-per-unit-area of radiative heat dissipation. Nanoscale carbon fibers/nanotubes can be used as templates for the generation of nanosilica. A sol-gel operation is employed for this purpose.
Caneba, Gerard T.↗
Two-Dimensional Finite Element Ablative Thermal Response Analysis of an Arcjet Stagnation Test
The finite element ablation and thermal response (FEAtR, hence forth called FEAR) design and analysis program simulates the one, two, or three-dimensional ablation, internal heat conduction, thermal decomposition, and pyrolysis gas flow of thermal protection system materials. As part of a code validation study, two-dimensional axisymmetric results from FEAR are compared to thermal response data obtained from an arc-jet stagnation test in this paper. The results from FEAR are also compared to the two-dimensional axisymmetric computations from the two-dimensional implicit thermal response and ablation program under the same arcjet conditions. The ablating material being used in this arcjet test is phenolic impregnated carbon ablator with an LI-2200 insulator as backup material. The test is performed at the NASA, Ames Research Center Interaction Heating Facility. Spatially distributed computational fluid dynamics solutions for the flow field around the test article are used for the surface boundary conditions.
Dec, John A.↗