Search NASA⌕ Search

SEARCH · Search NASA

Results for “trimming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Aeroelastic stability and control of an oblique wing

Dynamic model tests were staged to compare the aeroelastic stability of a free-flying oblique-winged aircraft and the known divergent instability characterizing swept-forward wing configurations, to test the effect of wing elasticity on aileron control and trim. The aircraft fuselage was clamped in some tests and left free to roll in others. Two rigid wing panels were hinged near the wing center with elastic restraining springs. It is found that the aeroelastic divergence affecting swept-forward wings does not occur with an oblique wing, whose aeroelastic instability sets in at a dynamic pressure exceeding that for static divergence of swept-forward wings, and appears in the form of undamped oscillations. Oblique wing stability is sensitive to the moment of inertia of the fuselage in roll. Roll control and lateral trim are attainable with conventional ailerons, even at speeds at which divergence of a clamped forward wing shows up.

Jones, R. T.↗
NASA NTRS1976

Rotor Dynamic State and Parameter Identification from Hovering Transients

State and parameter identifications based on a form of the maximum likelihood method are applied to the problem of extracting linear perturbation models, including rotor dynamic inflow effects, from transient blade flapping measurements. The estimation method is first studied in computer simulations and then applied to cyclic pitch stirring transients generated with a four-bladed rotor model operating in hovering trim conditions. The analytical perturbation models extracted from the transient test results are compared with transient and frequency response tests not used in the state and parameter identification. The identified analytical perturbation model is also compared with a simple theory. The method that is applicable both to small scale and full scale dynamic rotor testing is being extended to perturbations from forward flight trim conditions.

Hohenemser, K. H.↗
NASA NTRS1976

Method of discrete modeling and its application to estimation of TF30 engine variables

A method of discrete modeling is presented that effectively isolates steady state model accuracy from dynamic model accuracy. The steady state model may be generated from the engine design equations with any desired degree of accuracy. The dynamic model is generated by applying a step disturbance of a manipulated variable to an open loop engine simulation. The sampled response of the variable is combined with the steady state model's response to form a set of weighting factors. These weighting factors are then used to weight past values of the manipulated variable, thus forming the dynamic model. The method is used to estimate various TF30-P-3 engine variables. A dynamic trim function is developed to compensate for the dynamic nonlinearities of the variables as well as for inaccuracies in dynamic definition. The trim function is shown to be realted to the square root of the sum of the squares of the weighting factors obtained at various engine operating conditions. Finally, the estimation of variables without dynamic modeling is discussed.

Arpasi, D. J.↗
NASA NTRS1976

FLEXSTAB: A computer program for the prediction of loads and stability and control of flexible aircraft

Capabilities of the FLEXSTAB Computer Program System are described and illustrated. Aeroelastic analysis of a wide variety of aircraft configurations is performed. The aerodynamic theory used in FLEXSTAB is applicable to both steady and unsteady, subsonic and supersonic flow for multiple wing-body tail nacelle configurations with a plane of symmetry. For unsteady flow calculations, an unsteady aerodynamic theory is used which is appropriate for the low reduced frequencies associated with aircraft flight dynamics. The aircraft is modeled as either a rigid or flexible structure. The computer trims the aircraft in steady reference flight and computes both static and dynamic stability and control derivatives and the stability behavior about the trim condition. The airplane lifting pressure distribution, aerodynamic and inertia loads and deflected shape are also computed.

Perkin, B. R.↗
NASA NTRS1977

Lateral aerodynamic parameters extracted from flight data for the F-8C airplane in maneuvering flight

Flight test data are used to extract the lateral aerodynamic parameters of the F-8C airplane at moderate to high angles of attack. The data were obtained during perturbations of the airplane from steady turns with trim normal accelerations from 1.5g to 3.0g. The angle-of-attack variation from trim was negligible. The aerodynamic coefficients extracted from flight data were compared with several other sets of coefficients, and the extracted coefficients resulted in characteristics for the Dutch roll mode (at the highest angles of attack) similar to those of a set of coefficients that have been the basis of several simulations of the F-8C.

Suit, W. T.↗
NASA NTRS1977

Aerodynamic characteristics at Mach 6 of a hypersonic research airplane concept having a 70 deg swept delta wing

The hypersonic aerodynamic characteristics of an air-launched, delta-wing research aircraft concept were investigated at Mach 6. The effect of various components such as nose shape, wing camber, wing location, center vertical tail, wing tip fins, forward delta wing, engine nacelle, and speed brakes was also studied. Tests were conducted with a 0.021 scale model at a Reynolds number, based on model length, of 10.5 million and over an angel of attack range from -4 deg to 20 deg. Results show that most configurations with a center vertical tail have static longitudinal stability at trim, static directional stability at angles of attack up to 12 deg, and static lateral stability throughout the angle of attack range. Configurations with wing tip fins generally have static longitudinal stability at trim, have lateral stability at angles of attack above 8 deg, and are directionally unstable over the angle of attack range.

Clark, L. E.↗
NASA NTRS1977

Documentation of GEMASS entry to touchdown simulation

The entry-to-touchdown space shuttle orbiter simulation capability incorporated into the GEMASS subprogram 33 (3-DOF) is documented. A digital autopilot interfaces between GEMASS and the guidance. Vehicle attitude is determined by use of the ability of GEMASS to integrate differential equations in addition to the equations of motion. Vehicle aerodynamic characteristics are obtained from an aerodynamic data tape and control surface deflections required to trim the vehicle, and trimmed aerodynamic coefficients are determined internally. Several indicators to allow evaluation of subsystem performance are included; as is the ability of the user to activate any of several error dispersion sources. The performance of the simulation compares well with more sophisticated simulations.

Waibel, R. H.↗
NASA NTRS1976

Some theoretical considerations of longitudinal stability in power-on flight with special reference to wind-tunnel testing, November 1942

Some problems relating to longitudinal stability in power-on flight are considered. A derivation is included which shows that, under certain conditions, the rate of change of the pitching moment coefficient with lift coefficient as obtained in wind tunnel tests simulating constant power operation is directly proportional to one of the indices of stability commonly associated with flight analysis, (the slope of the curve relating the elevator angle for trim and lift coefficient). The necessity of analyzing power-on wind tunnel data for trim conditions is emphasized, and a method is provided for converting data obtained from constant thrust tests to simulated constant throttle flight conditions.

Donlan, C. J.↗
NASA NTRS1976

Current status of longitudinal stability, 24 May 1948

The problems of static and dynamic longitudinal stability both at high speeds and at low speeds are discussed and data are presented which indicate progress made in the solution of these problems. It is shown that the incorporation of large amounts of sweepback on both the wing and the horizontal tail can significantly increase the Mach number at which critical trim changes and stability changes occur and can greatly reduce the trim changes and stability changes encountered at supercritical speeds. Data are also presented which demonstrate the possibility of obtaining satisfactory longitudinal stability in the landing configuration for wings with sweepback of the order of 45 deg utilizing various stall control devices. Optimum arrangements for such devices, however, should be determined experimentally.

Donlan, C. J.↗
NASA NTRS1976

Summary of low-speed aerodynamic characteristics of upper-surface-blown jet-flap configurations

The results of recent wind tunnel investigations to provide fundamental information on the upper surface blown (USB) jet flap concept demonstrated that the USB concept provides good high-lift performance. It is shown that the low speed performance is dependent upon the jet turning angle and turning efficiency and on the use of proper leading and trailing edge treatment to prevent premature flow separation. The best means of achieving good turning performance in any particular USB application must be determined from overall operational considerations in which high speed performance, structures and noise, as well as low speed performance, are evaluated. The large diving moments generated at high lift coefficients can be trimmed satisfactorily with a large, conventional horizontal tail; a high tail position is best from longitudinal stability considerations. Large rolling and yawing moments are introduced with the loss of an engine, but these moments can be trimmed satisfactorily through the use of asymmetrical boundary layer control and through the use of spoiler and rudder deflection as needed.

Phelps, A. E., III↗
NASA NTRS1978

Aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing at Mach number 0.2

A wind-tunnel of the static longitudinal, lateral and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing was conducted in the Langley low-turbulence pressure tunnel. The configuration variables included wing planform, tip fins, center fin, and scramjet engine modules. A mach number of 0.2 was investigated over a Reynolds number (based on fuselage length) range of 2,200,000 to 19.75 x 1,000,000 (with a majority of tests at 10.0 x 1,000,000. Tests were conducted through an angle-of-attack range from about -2 deg to 34 deg at angles of sideslip of 0 deg to 5 deg, and at elevon deflection of 0 deg, -5 deg, -10 deg, -15 deg, and -20 deg. The drag coefficient of the integrated scramjet engine appears relatively constant with Reynolds number at the test Mach number of 0.2. Mild pitch-up was exhibited by the models equipped with tip fins. The forward delta, a highly swept forward portion of the wing, was destabilizing. The center fin model has a higher trimmed maximum lift-drag ratio and a wider trim lift and angle-of-attack range than the tip fin model. Both the tip fin models and center fin models exhibited positive dihedral effect and positive directional stability. Roll control was positive for the tip fin model, but yaw due to roll control was unfavorable.

Penland, J. A.↗
NASA NTRS1979

Transition aerodynamics for close-coupled wing-canard configuration

A series of wind-tunnel tests have been conducted in the Langley V/STOL tunnel to investigate the low-speed longitudinal aerodynamics of two powered close-coupled wing-canard fighter configurations. A brief review is provided of the high angle-of-attack data for the two wing-canard configurations tested showing the benefits and problem areas of powered lift. A takeoff and landing analysis is presented which defines the area in which a fighter-type aircraft must operate in order to achieve 305-m field lengths. The wing-canard configuration data are analyzed in detail showing the problems of obtaining high lift, high drag, and trimmed moments. Assuming that power will be used to trim the aircraft, data are presented comparing the transition aerodynamics of the wing-canard configuration using a nose jet with several V/STOL configurations.

Paulson, J. W., Jr.↗
NASA NTRS1979

Space Shuttle orbital flight testing

The paper discusses the plans for the stability and control aspects of the Space Shuttle orbital flight testing. The first flight plan calls for the design of trajectory, cg, and trim schedules which are as tolerant as possible with regard to all the constraints and aerodynamic uncertainties. Vehicle configuration control and downmoding switches will be used to provide capabilities to handle the off-nominal conditions that might be encountered. Measured trim conditions will provide information on the control effector characteristics and provide an early estimate of the control boundaries.

Hartsfield, H. W., Jr.↗
NASA NTRS1979

Control considerations for CCV fighters at high angles of attack

Wind tunnel and piloted simulation studies were conducted to investigate the potential high angle of attack control problems that are introduced by the use of the CCV concept of relaxed static pitch stability (RSS) on fighter aircraft. A conventional wing/aft tail design incorporating modest levels of static instability and a close-coupled canard/wing design exhibiting very high levels of instability was investigated. Two types of high angle of attack control problems can result from the use of RSS: pitch departures caused by coupling and deep stall trim. Avoidance of these problems requires that the airplane have sufficient nose-down pitch control at high angles of attack. The effectiveness of several pitch control configurations were investigated including conventional aft-mounted stabilators, wing-mounted elevators, canard-mounted flaps, and all-moveable canards. Varying the incidence of the canards was the most effective scheme; however, very large deflections may be required on highly unstable configurations to prevent pitch departure without sacrificing roll performance and to avoid deep stall trim. For situations where the high angle of attack pitch control requirement is not met, control laws were developed to inhibit the departure and to allow deep stall recovery. However, these schemes involve limiting airplane roll capability and therefore can potentially compromise maneuverability.

Nguyen, L. T.↗
NASA NTRS1980

Magsat attitude dynamics and control: Some observations and explanations

Before its reentry 7 months after launch, Magsat transmitted an abundance of valuable data for mapping the Earth's magnetic field. As an added benefit, a wealth of attitude data for study by spacecraft dynamicists was also collected. Because of its unique configuration, Magsat presented new control problems. With its aerodynamic trim boom, attitude control was given an added dimension. Minimization of attitude drift, which could be mapped in relative detail, became the goal. Momentum control, which was accomplished by pitching the spacecraft in order to balance aerodynamic and gravity gradient torques, was seldom difficult to achieve. Several interesting phenomena observed as part of this activity included occasional momentum wheel instability and a rough correlation between solar flux and the pitch angle required to maintain acceptable momentum. An overview is presented of the attitude behavior of Magsat and some of the control problems encountered. Plausible explanations for some of this behavior are offered. Some of the control philosophy used during the mission is examined and aerodynamic trimming operations are summarized.

Stengle, T. H.↗
NASA NTRS1980

Effect of wing location and strakes on stability and control characteristics of a monoplanar circular missile with low-profile tail fins at supersonic speeds

A wind tunnel test was conducted at Mach numbers from 1.70 to 2.86 to extend the aerodynamic data base for wing tail effect on stability and control characteristics of monoplanar missiles. The results are summarized to show the effects of tail fin dihedral angle, wing location, and nose body strakes. The results indicate that an increase in tail fin dihedral angle produces positive increments in directional stability that allow greater trimmed lift coefficient values (maneuver potential) to be obtained. An increase in wing tail gap for the Mach number range reduces the aerodynamic center travel and produces reductions in directional stability at the lower angles of attack. A change in wing height (vertical location) strongly influences the angle of attack at which pitch up and the most directional stability occur. The addition of strakes to the baseline configuration increases directional stability, which allows a significant increase in stable trimmed maneuver capability. The tail fins of the baseline configuration are effective in producing roll and yaw control that are accompanied by favorable yaw and roll, respectively.

Blair, A. B., Jr.↗
NASA NTRS1980

Analytic development of improved supersonic cruise aircraft based on wind tunnel data

Data obtained from the MDC/NASA cooperative wing tunnel program were used to develop empirical corrections to theory. These methods were then used to develop a 2.2M supersonic cruise aircraft configuration with a cruise trimmed maximum L/D of 10.2. The empirical corrections to the theory are reviewed, and the configuration alternatives examined in the development of the configuration are presented. The benefits of designing for optimum trimmed performance, including the effects of the nacelles, are discussed.

Roensch, R. L.↗
NASA NTRS1981

Comparisons of AEROX computer program predictions of lift and induced drag with flight test data

The AEROX aerodynamic computer program which provides accurate predictions of induced drag and trim drag for the full angle of attack range and for Mach numbers from 0.4 to 3.0 is described. This capability is demonstrated comparing flight test data and AEROX predictions for 17 different tactical aircraft. Values of minimum (skin friction, pressure, and zero lift wave) drag coefficients and lift coefficient offset due to camber (when required) were input from the flight test data to produce total lift and drag curves. The comparisons of trimmed lift drag polars show excellent agreement between the AEROX predictions and the in flight measurements.

Axelson, J.↗