Search NASA⌕ Search

SEARCH · Search NASA

Results for “vehicle matching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Single block three-dimensional volume grids about complex aerodynamic vehicles

This paper presents an alternate approach for the generation of volumetric grids for supersonic and hypersonic flows about complex configurations. The method uses parametric two-dimensional block-face grid definitions, within the framework of GRIDGEN2D. The incorporation of a face decomposition reduces complex surfaces to simple shapes. These simple shapes are recombined to obtain the final face definition. The advantages of this method include the reduction of overall grid generation time through the use of vectorized computer code, the elimination of generating matching block faces, and simplified boundary conditions.

Alter, Stephen J.↗
NASA NTRS1993

Single block three-dimensional volume grids about complex aerodynamic vehicles

This paper presents an alternate approach for the generation of volumetric grids for supersonic and hypersonic flows about complex configurations. The method uses parametric two dimensional block face grid definition within the framework of GRIDGEN2D. The incorporation of face decomposition reduces complex surfaces to simple shapes. These simple shapes are combined to obtain the final face definition. The advantages of this method include the reduction of overall grid generation time through the use of vectorized computer code, the elimination of the need to generate matching block faces, and the implementation of simplified boundary conditions. A simple axisymmetric grid is used to illustrate this method. In addition, volume grids for two complex configurations, the Langley Lifting Body (HL-20) and the Space Shuttle Orbiter, are shown.

Alter, Stephen J.↗
NASA NTRS1980

A propulsion and steering control system for the Mars rover

The design of a propulsion and steering control system for the Rensselaer Polytechnic Institute prototype autonomous Mars roving vehicle is presented. The vehicle is propelled and steered by four independent electric motors. The control system must regulate the speeds of the motors so they work in unison during turns and on irregular terrain. An analysis of the motor coordination problem on irregular terrain, where each motor must supply a different torque at a different speed is presented. A procedure was developed to match the output of each motor to the varying load. A design for the control system is given. The controller uses a microprocessor which interprets speed and steering commands from an off-board computer, and produces the appropriate drive voltages for the motors.

Turner, J. M.↗
NASA NTRS1993

Lunar science strategy: Exploring the Moon with humans and machines

Important scientific questions that can be addressed from the lunar surface are reviewed for a number of scientific disciplines. A successful strategy for human exploration of the Moon is outlined. It consists of several elements: thorough preparation; a means of extending the human reach; measurement of the mobility of both human and robotic components; and flexible technologies so as to be able to take the most effective path as successive decision points occur. Part of thorough preparation involves concurrent development of a set of science goals and objectives as well as a supporting information base; neither can evolve independently of the other. This matched set will drive the definition of missions and technologies used to satisfy the requirements of various science disciplines. No single site on the Moon will satisfy all requirements. Thus, global accessibility is a goal of the current Lunar and Mars Exploration Program science strategy. Human mobility on the surface is limited to a few kilometers without the use of vehicles. Unpressurized crew carrying rovers could take explorers to distances tens of kilometers from an outpost; the distance is primarily limited by health and safety concerns. Pressurized rovers could extend the range to hundreds of kilometers, but size, mass, and costs limit such vehicles to missions beyond current planning horizons. The establishment of several outposts instead of one would provide opportunities for effective use of the unique capabilities of humans. Extending the human reach to global dimensions may be accomplished through teleoperation or telepresence. The most effective mix of these techniques is a decision that will evolve as experience is gained on the surface. Planning and technology must be flexible enough to allow a variety of options to be selected.

Morrison, Donald A.↗
DOE OSTI2021

Shared automated vehicle fleet operations for first-mile last-mile transit connections with dynamic pooling

Shared automated vehicles (SAVs) have the potential to promote transit ridership by providing efficient first-mile last-mile (FMLM) connections through reduced operational costs to fleet providers and lower out-of-pocket costs to riders. To help plan for a future of integrated mobility, this paper investigates the impacts of SAVs serving FMLM connections, as a mode that provides flexibility in access/egress decisions and is well coordinated with train station schedules. To achieve this objective, a novel dynamic pooling algorithm was introduced to match SAVs with riders while coordinating the riders' arrival times at the light-rail station to a known train schedule. Microsimulations of SAVs and travelers throughout two central Austin neighborhoods show how larger service areas, higher levels of SAV demand, and longer arrival times between successive trains require larger SAV fleet sizes and higher SAV utilization rates to deliver close traveler wait times. Four-person SAVs appear to perform similar to 6-seat SAVs but will cost less to provide. Using a dynamic pooling algorithm tightly coordinated with train arrivals (every 15 min) delivers 87% of travelers to their stations in time to catch the next train, whereas uncoordinated assignments deliver just 58% of travelers in time.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS2024

Implementation of a First-Order Quadratic Program Solver in C

This paper details a translation of a first order quadratic program (QP) solver from MATLAB to C. NASA could use this QP solver to generate online flight path trajectories for powered descent vehicles during landing. Over 12 weeks, the team designed, implemented, and tested two iterations of the QP solver for accuracy and runtime on 104 benchmark QP tests. The final iteration was 541.07% faster than the first, handling most tests in under one second. Additionally, it solved four more QP tests for N≥1383, and all outputs for cost and D_x matched the MATLAB reference values.

Optimization↗
NASA NTRS1992

Computational method to predict thermodynamic, transport, and flow properties for the modified Langley 8-foot high-temperature tunnel

The Langley 8 foot high temperature tunnel (8 ft HTT) is used to test components of hypersonic vehicles for aerothermal loads definition and structural component verification. The test medium of the 8 ft HTT is obtained by burning a mixture of methane and air under high pressure; the combustion products are expanded through an axisymmetric conical contoured nozzle to simulate atmospheric flight at Mach 7. This facility was modified to raise the oxygen content of the test medium to match that of air and to include Mach 4 and Mach 5 capabilities. These modifications will facilitate the testing of hypersonic air breathing propulsion systems for a wide range of flight conditions. A computational method to predict the thermodynamic, transport, and flow properties of the equilibrium chemically reacting oxygen enriched methane-air combustion products was implemented in a computer code. This code calculates the fuel, air, and oxygen mass flow rates and test section flow properties for Mach 7, 5, and 4 nozzle configurations for given combustor and mixer conditions. Salient features of the 8 ft HTT are described, and some of the predicted tunnel operational characteristics are presented in the carpet plots to assist users in preparing test plans.

Venkateswaran, S.↗
NASA NTRS2004

Tropical Cyclone Precipitation Types and Electrical Field Information Observed by High Altitude Aircraft Instrumentation

During the 1998 and 200 1 hurricane seasons of the Atlantic Ocean Basin, the Advanced Microwave Precipitation Radiometer (AMPR), the ER-2 Doppler (EDOP) radar, and the Lightning Instrument Package (LIP) were flown aboard the National Aeronautics and Space Administration (NASA) ER-2 high altitude aircraft as part of the Third Convection And Moisture Experiment (CAMEX-3) and the Fourth Convection And Moisture Experiment (CAMEX-4). Several hurricanes and tropical storms were sampled during these experiments. A rainfall screening technique has been developed using AMPR passive microwave observations of these tropical cyclones (TC) collected at frequencies of 10.7, 19.35,37.1, and 85.5 GHz and verified using vertical profiles of EDOP reflectivity and lower altitude horizontal reflectivity scam collected by the National Oceanic and Atmospheric Administration (NOM) P-3 radar. Matching the rainfall classification results with coincident electrical field information collected by the LIP readily identifl convective rain regions within the TC precipitation fields. Strengths and weaknesses of the rainfall classification procedure will be discussed as well as its potential as a real-time analysis tool for monitoring vertical updrafl strength and convective intensity from a remotely operated or uninhabited aerial vehicle.

Hood, Robbie E.↗
NASA NTRS2004

Evaluation of a CFD Method for Aerodynamic Database Development using the Hyper-X Stack Configuration

A computational fluid dynamic (CFD) study is performed on the Hyper-X (X-43A) Launch Vehicle stack configuration in support of the aerodynamic database generation in the transonic to hypersonic flow regime. The main aim of the study is the evaluation of a CFD method that can be used to support aerodynamic database development for similar future configurations. The CFD method uses the NASA Langley Research Center developed TetrUSS software, which is based on tetrahedral, unstructured grids. The Navier-Stokes computational method is first evaluated against a set of wind tunnel test data to gain confidence in the code s application to hypersonic Mach number flows. The evaluation includes comparison of the longitudinal stability derivatives on the complete stack configuration (which includes the X-43A/Hyper-X Research Vehicle, the launch vehicle and an adapter connecting the two), detailed surface pressure distributions at selected locations on the stack body and component (rudder, elevons) forces and moments. The CFD method is further used to predict the stack aerodynamic performance at flow conditions where no experimental data is available as well as for component loads for mechanical design and aero-elastic analyses. An excellent match between the computed and the test data over a range of flow conditions provides a computational tool that may be used for future similar hypersonic configurations with confidence.

Parikh, Paresh↗
NASA NTRS1972

Determination of stability derivatives from flight data using a Newton-Raphson minimization technique

A modified Newton-Raphson or quasilinearization minimization technique for determining stability derivatives from flight data was developed and compared with simple-equations, analog-matching, least-squares, and Shinbrot methods of analysis. For the data analyzed, the solutions computed by using the estimates obtained from the Newton-Raphson technique fit the data and determined coefficients adequately. A further modification to include a priori information was found to be useful. A model statistically similar to the flight data was analyzed using the same methods (excluding analog matching), and the Newton-Raphson technique was found to yield superior estimates. An approximate Cramer-Rao bound was compared with the error covariance matrix of the model and was found to provide information about the reliability of the individual estimates obtained. The technique was successfully applied to data obtained from a light airplane, a large supersonic airplane, and a lifting body vehicle. It was shown that the reliability of the estimates of a given coefficient obtained from these vehicles depends upon the data analyzed.

Iliff, K. W.↗
NASA NTRS1991

End-loaded crossed-slot radiating elements

Three cavity-backed crossed-slot antenna configurations are described that offer simple design, easy frequency tuning, light weight, low loss, and low cost. These antennas are designed for mobile satellite (MSAT) vehicle phased-array applications. The slots in these antennas are end-loaded. The end loading makes the slots effectively longer, and hence reduces their resonant frequency. Therefore, relatively small radiating elements can be achieved for large-angle-scanning phased-array antennas. These antennas have good RF characteristics and provide a relatively wide bandwidth without needing external tuning circuits for impedance matching. Measurements for the return loss and the far-field pattern of these antennas are presented.

Manshadi, F.↗
NASA NTRS1999

STS-93 SSME Nozzle Tube Rupture Investigation

STS-93 was launched on July 23, 1999. There was an anomaly at the end of the launch in that the main engines shut down 0.16 second early because sensors detected a low level of oxidizer in the LOX tank (actually the duct from the tank to the vehicle). This resulted in a cutoff velocity for the vehicle that was 16 ft/sec low. It should have been 25872 ft/sec. The OMS engines were subsequently used to achieve the proper orbit. An investigation was immediately initiated into the cause of this LOX tank low level cutoff. It was noticed during the launch that the turbine temperatures for Main Engine 3 (E2019) were approximately 100 F higher than the preflight prediction. Linear Engine Model matching of the data indicated that a nozzle leak best fit the data. Post launch review of the data showed, that at approximately five seconds into the start, numerous parameters indicated small anomalous shifts. These shifts were all consistent with a rupture of nozzle tubes. Post launch review of the films showed that just after Space Shuttle Main Engine (SSME) ignition and just prior to liftoff a streak is seen in the exhaust plume of E2019. Just after liftoff the streak can be seen emanating from the nozzle wall. This photo confirmed that a leak was coming from the nozzle tubes. Based on the photo, the axial location of the leak was estimated to be 28 in. from the aft end of the nozzle and in line with nozzle coolant feed line #1. The streak continued to be visible during the launch.

Romine, W. Dennis↗
DOE OSTI2021

Nuclear Safeguards: Feature Extraction for Machine Learning Enrichment Analysis of UF 6 Cylinders

With the increasing international interest in using nuclear material as sources of energy, comes the growing concern that we may see an increase in proliferation threats. Uranium hexafluoride (UF 6 ) is used in the nuclear fuel cycle for uranium enrichment. Inspectors from the International Atomic Energy Agency (IAEA) monitor the enrichment levels of UF 6 stored in transportation cylinders, to ensure the enrichments match that of a facility operator’s declarations. However, only a characteristic subset of UF 6 cylinders can be measured by inspectors from the IAEA during these inspections. In turn, the inspector may not identify a cylinder whose enrichment levels do not match the facility declarations. Therefore, our team attempts to develop a machine learning network that could determine the enrichment percentage of cylinders as they enter and exit facilities. The machine learning model must be robust against spectral variations due to factors that are internal and external to the UF 6 cylinder. Such factors include but are not limited to the speed and distance of the moving vehicle, cylinder type, cylinder orientation, and fill level. Many features in the spectral continuum can be used to identify and correct for some of these variations. As a consequence, the model must extract numerous features in the continuum. We investigate new approaches in continuum subtraction to verify enrichment percentage: interpolation and extrapolation of lines at the notable characteristic spectral peaks. It was determined that there was no clear answer on which method proved superior, therefore the decision was made to implement both new methods into the current codebase. We currently rely on synthetic training and testing data to analyze the results and fine tune our models but hope to test the system on measured data soon.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
NASA NTRS1983

Integral inverter/battery charger for use in electric vehicles

The design and test results of a thyristor based inverter/charger are discussed. A battery charger is included integral to the inverter by using a subset of the inverter power circuit components. The resulting charger provides electrical isolation between the vehicle propulsion battery and ac line and is capable of charging a 25 kWh propulsion battery in 8 hours from a 220 volt ac line. The integral charger employs the inverter commutation components at a resonant ac/dc isolated converter rated at 3.6 kW. Charger efficiency and power factor at an output power of 3.6 kW are 86% and 95% respectively. The inverter, when operated with a matching polyphase ac induction motor and nominal 132 volt propulsion battery, can provide a peak shaft power of 34 kW (45 ph) during motoring operation and 45 kW (60 hp) during regeneration. Thyristors are employed for the inverter power switching devices and are arranged in an input-commutated topology. This configuration requires only two thyristors to commutate the six main inverter thyristors. Inverter efficiency during motoring operation at motor shaft speeds above 450 rad/sec (4300 rpm) is 92-94% for output power levels above 11 KW (15 hp). The combined ac inverter/charger package weighs 47 kg (103 lbs).

Thimmesch, D.↗
NASA NTRS2001

Computation of External Aerodynamics for a Canard Rotor/Wing Aircraft

The aerodynamic loads on a Canard Rotor/Wing vehicle are investigated using inviscid numerical simulations in order to understand the flight characteristics of the vehicle during conversion from rotor craft to fixed-wing flight. A series of numerical simulations at seven azimuthal rotor indices are presented covering a quarter turn of the rotor With symmetry arguments, these simulations produce 25 data points for a complete rotation. A Cartesian mesh approach is used to compute the flow field about a configuration with faired-over engine inlet and exhaust that matches the wind tunnel geometry. These simulations were performed using meshes with approximately nine Million Cartesian cells. To better understand the aerodynamic effects of the rotor hub on the configuration, the same set of simulations were repeated for a hub-less geometry. Overall loads for both configurations are similar but are due to somewhat different aerodynamic mechanisms.

Pandya, S. A.↗
NASA NTRS2003

A Comparison of Active and Passive Methods for Control of Hypersonic Boundary Layers on Airbreathing Configurations

Active and passive methods for control of hypersonic boundary layers have been experimentally examined in NASA Langley Research Center wind tunnels on a Hyper-X model. Several configurations for forcing transition using passive discrete roughness elements and active mass addition, or blowing, methods were compared in two hypersonic facilities, the 20-Inch Mach 6 Air and the 31-Inch Mach 10 Air tunnels. Heat transfer distributions, obtained via phosphor thermography, shock system details, and surface streamline patterns were measured on a 0.333-scale model of the Hyper-X forebody. The comparisons between the active and passive methods for boundary layer control were conducted at test conditions that nearly match the nominal Mach 7 flight trajectory of an angle-of-attack of 2-deg and length Reynolds number of 5.6 million. For the passive roughness examination, the primary parametric variation was a range of trip heights within the calculated boundary layer thickness for several trip concepts. The prior passive roughness study resulted in a swept ramp configuration being selected for the Mach 7 flight vehicle that was scaled to be roughly 0.6 of the calculated boundary layer thickness. For the active jet blowing study, the blowing manifold pressure was systematically varied for each configuration, while monitoring the mass flow, to determine the jet penetration height with schlieren and transition movement with the phosphor system for comparison to the passive results. All the blowing concepts tested were adequate for providing transition onset near the trip location with manifold stagnation pressures on the order of 40 times the model static pressure or higher.

Berry, Scott A.↗
DOE OSTI2022

A Highly Effective African Swine Fever Virus Vaccine Elicits a Memory T Cell Response in Vaccinated Swine

African Swine Fever Virus (ASFV) is the causative agent of a highly contagious and lethal vector-borne disease in suids. Recently, a live attenuated virus strain, developed using the currently circulating, virulent Georgia strain (ASFV-G) with a single gene deletion (ASFV-G-ΔI177L), resulted in an effective vaccine. Nevertheless, protective immune response mechanisms induced by this candidate are poorly understood. In this study, Yorkshire crossbred swine intramuscularly vaccinated with 10 6 50% hemadsorption dose (HAD 50 ) of ASFV-G-ΔI177L or a vehicle control were challenged at 28 days post-inoculation (dpi) with 10 2 HAD 50 of ASFV-G. Analysis of purified peripheral blood mononuclear cells following inoculation and challenge revealed that CD4+, CD8+ and CD4+CD8+ central memory T cells (CD44+CD25–CD27–CD62L+CCR7+, T cm ) decreased significantly by 28 dpi in ASFV-G-ΔI177L-vaccinated swine compared to baseline and time-matched controls. Conversely, CD4+, CD8+ and CD4+CD8+ effector memory T cells (CD44+CD25–CD27–CD62–CCR7–, T em ) increased significantly among ASFV-G-ΔI177L-vaccined swine by 28 dpi compared to baseline and time-matched controls. Additionally, the percentage of natural killer (NK), CD4+ and CD4+CD8+ T em and CD8+ T cm and T em positive for IFNγ increased significantly following inoculation, surpassing that of controls by 28 dpi or earlier. These results suggest that NK and memory T cells play a role in prote

60 APPLIED LIFE SCIENCES↗
NASA NTRS2025

Subsonic Ultra Green Aircraft Research: Phase V – Buffet Test Report

This test report summarizes work performed by the Boeing Subsonic Ultra-Green Aircraft Research (SUGAR) team in the Phase V Transonic Truss-Braced Wing contract task. The task was awarded in September 2020, and ended at the end of September 2022. As a part of the SUGAR Phase V contract task, Boeing developed a wind tunnel test plan, model requirements, then fabricated and conducted a dedicated transonic buffet wind tunnel test. The test focused on the investigation of buffet onset, and the ability to accurately predict buffet onset for the TTBW configuration. This report summarizes the results and post-test analysis of the 9% scale, semispan, Transonic Truss-Braced Wing (TTBW) transonic buffet model tested at the NASA Ames Research Center Unitary Plan Wind Tunnel (UPWT) 11-Foot Transonic Wind Tunnel (11-Ft TWT) facility located at Moffett Field, CA. It was tested from January 24, 2022, through February 18, 2022. The wind tunnel test was successful in capturing buffet onset at the model design dynamic pressure. Multiple configurations were tested starting in the wing-body-strut configuration and ending with the full configuration including wing-body-strut-nacelle/pylon, and flap hinge. The test also measured the effect of control surface deflections (ailerons and spoilers), as well as the effect of an outboard strut flap. Steady data collected during the test included standard force and moment measurements, as well as wing, strut, nacelle, and body (fuselage) static pressures. These data were collected in a standard pitch-pause mode. Unsteady data captured in the test, collected in continuous pitch mode, included wing and strut dynamic pressures, accelerations, and strains. According to test data, previous concerns regarding critical buffet onset on the strut (at low vehicle lift coefficient) and in the wing-strut channel have been mitigated. Buffet onset on the TTBW appears to follow conventional wing-induced buffet onset mechanisms. However, the critical station where buffet onset first occurs has moved inboard to the wing-strut juncture span location (55-60% span) from the typical ~70% span location. Test data obtained by unsteady pressure transducers provided a good match to expected buffet onset modes. An assessment of different tools and methodologies for predicting buffet onset was conducted. Reasonable agreement was found for buffet boundary predictions between most of the methods examined when using a forward trip location, with the greatest discrepancies from the pitching moment break and trailing edge pressure divergence methods. When an aft trip location was used the buffet boundary predictions diverged more significantly from unsteady pressure measurements. In addition, good agreement between the buffet onset trends were found when the Reynolds number, configuration, or spanload was changed.

strut↗