Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALTITUDE SIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Passive Thermal Control for the Low Density Supersonic Decelerator (LDSD) Test Vehicle Spin Motors Sub-System

Future missions to Mars will require improved entry, descent, and landing (EDL) technology over the Viking-heritage systems which recently landed the largest payload to date, the 900 kg Mars Science Laboratory. As a result, NASA's Low Density Supersonic Decelerator (LDSD) project is working to advance the state of the art in Mars EDL systems by developing and testing three key technologies which will enable heavier payloads and higher altitude landing sites on the red planet. These technologies consist of a large 33.5 m diameter Supersonic Disk Sail (SSDS) parachute and two different Supersonic Inflatable Aerodynamic Decelerator (SIAD) devices - a robotic class that inflates to a 6 m diameter torus (SIAD-R), and an exploration class that inflates to an 8 m diameter isotensoid (SIADE). All three technologies will be demonstrated on test vehicles at high earth altitudes in order to simulate the Mars EDL environment. Each vehicle will be carried to altitude by a large helium balloon, released, spun up using spin motors to stabilize the vehicle's trajectory, and accelerated to supersonic speeds using a large solid rocket motor. The vehicle will then be spun down using another set of spin motors, and will deploy either the SIAD-R or SIAD-E, followed by the SSDS parachute until the vehicle lands in the ocean. Component level testing and bounding analysis are used to ensure the survival of system components in extreme thermal environments and predict temperatures throughout the flight. This paper presents a general description of the thermal testing, model correlation, and analysis of the spin motor passive thermal control sub-system to maintain spin motor performance, prescribed vehicle trajectory, and structural integrity of the test vehicle. The spin motor subsystem is predicted to meet its requirements with margin.

thermal analysis↗
NASA NTRS1977

Altitude test of several afterburner configurations on a turbofan engine with a hydrogen heater to simulate an elevated turbine discharge temperature

A performance test of several experimental afterburner configurations was conducted with a mixed-flow turbofan engine in an altitude facility. The simulated flight conditions were for Mach 1.4 at two altitudes, 12,190 and 14,630 meters. Turbine discharge temperatures of 889 and 1056 K were used. A production afterburner was tested for comparison. The research afterburners included partial forced mixers with V-gutter flameholders, a carburetted V-gutter flameholder, and a triple ring V-gutter flameholder with four swirl-can fuel mixers. Fuel injection variations were included. Performance data shown include augmented thrust ratio, thrust specific fuel consumption, combustion efficiency, and total pressure drop across the afterburner.

Johnsen, R. L.↗
NASA NTRS1972

Space shuttle orbiter reentry flow field and heating analysis

The reentry flow field and thermal environment around the straight wing shuttle orbiter vehicle were determined. Both rarefied and continuum flow fields and associated heating rates on various configurations representative of the orbiter at high angle of attack were calculated. Rarefied flow fields and heating rates were computed by the Monte Carlo direct simulation technique for altitudes above 82.3 km. Continuum inviscid flow fields were calculated by 2-D unsteady and 3-D steady finite difference/artificial viscosity methods and also by a 2-D shock layer analysis technique. Viscous flow fields and heating rates in the continuum regime were computed by a boundary layer integral matrix method for laminar flow and by an aerodynamic surface heating technique for turbulent flow. Shapes considered in the study included flat plates (representing the underside of the orbiter fuselage or the wing MAC), orbiter fuselage cross sections, orbiter wing airfoils, and 3-D orbiter configurations, all at high angle of attack (40 - 60 deg). The theoretical results showed good agreement with measured pressure and heat transfer data.

Rochelle, W. C.↗
NASA NTRS1972

A system for simulating aerial or orbital TV observations of geographic patterns

A system which simulates observation of the earth surface by aerial or orbiting television devices has been developed. By projecting color slides of photographs taken by aircraft and orbiting sensors upon a rear screen system, and altering scale of projected image, screen position, or TV camera position, it is possible to simulate alternatives of altitude, or optical systems. By altering scan line patterns in COHU 3200 series camera from 525 to 945 scan lines, it is possible to study implications of scan line resolution upon the detection and analysis of geographic patterns observed by orbiting TV systems.

Latham, J. P.↗
NASA NTRS1972

Hypergol engine restart characteristics.

Several hard restarts and two failures to restart occurred during simulated high-altitude testing of the three Apollo spacecraft primary propulsion engines. Abnormal restarts resulted from flow perturbations by trapped propellants, ignition characteristics of partially frozen propellants, and fuel nitrate retention. Engine restart characteristics are correlated with thermodynamic phenomena that occur after engine shutdown; these include desorption of dissolved pressurant gases and evaporative freezing of propellant residuals. These results are applied to conceptual space shuttle OMS hypergol engines to identify potential restart problems.

Kerkam, B. F.↗
NASA NTRS1976

Measurement of exhaust emissions from two J-58 engines at simulated supersonic cruise flight conditions

Emissions of total oxides of nitrogen, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16 to 23 km. For each flight condition, exhaust measurements were made for four or five power levels from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen (NOX) emissions decreased with increasing altitude, and increased with increasing flight speed. NOX emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude, and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without.

Holdeman, J. D.↗
NASA NTRS1976

The small motor plume/material impingement test program at MSFC utilizing nine different propellant formulations (April and May 1974), section 2

The relative effects of several candidate SSRM propellant formulations and their plume impingement effects on HRSI and RCC materials were evaluated. Nine solid propellant formulations were tested. The selected propellant matrix allowed an evaluation of propellants with and without metal additives, with and without burning rate catalyst, and low (approximately 1927 C) and high (approximately 2649 C) combustion temperatures. Motors were fired at a simulated SRB staging altitude of 3.96 km (130,000 ft) (nominal). The altitude pressure was predicted to drop approximately 0.6 km (20,000 ft) during a motor firing. All motors were loaded with 1.8 to 2.3 kg (4 to 5 lb) of propellant and burned for approximately 2 s.

Source record↗
NASA NTRS1976

Measurement of exhaust emissions from two J-58 engines at simulated supersonic cruise flight conditions

Emissions of total oxides of nitrogen, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16 to 23 km. For each flight condition, exhaust measurements were made for four or five power levels from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen emissions decreased with increasing altitude and increased with increasing flight speed. NO(x) emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without.

Holdeman, J. D.↗
NASA NTRS1986

Directional reflectance response in AVHRR red and near-IR bands for three cover types and varying atmospheric conditions

Surface directional red and near-infrared reflectances of bare soil, orchard grass, and fescue were extracted from a multitemporal data set to correspond to NOAA-7 Advanced Very High Resolution Radiometer (AVHRR) scanning and illumination geometry at 30 deg latitude. Radiances were simulated at satellite altitude and a ratio vegetation index was calculated. The results show that off-nadir directional reflectance measured at the surface in the red and near-IR portions of the spectrum are approximately maintained with AVHRR viewing and illumination characteristics. The two-channel reflectance response is such that the ratio vegetation index is more constant with scan angle and atmospheric conditions than individual channels. It is shown that inclusion of atmospheric and surface reflectance data can greatly improve interpretation of AVHRR data, when knowledge of the range of atmospheric conditions and approximate directional reflectances of major cover types are known.

Holben, B.↗
NASA NTRS1990

Modelling of E-region auroral winds

A numerical code, describing the interactions between chemistry and dynamics in the coupled thermosphere and ionosphere systems, has been used to investigate the morphology of wind systems of the auroral E-region and, in particular, their response to geomagnetic forcing. The structure and dynamics of both the thermosphere and the ionosphere show very strong interactions at all levels of geomagnetic disturbance. By comparison, other perturbations, particularly those resulting from tidal and gravity wave sources within the lower atmosphere, which are important and easily identified during quiet periods, are always overwhelmed by the magnitude of the effects of large geomagnetic disturbances above about 110 km altitude. The model simulations will be used to characterize the geomagnetic response of the E-region neutral wind, temperature, and composition in different parts of the polar cap and the auroral oval, and the major changes resulting from seasonal variations.

Rees, David↗
NASA NTRS1955

Performance of Four Experimental High-btu-per-gallon Fuels in a Single Turbojet Combustor

Performance characteristics of four hydrocarbon fuels having high Btu per gallon were determined in a single turbojet combustor. At simulated low-altitude operating conditions, the fuels with high Btu per gallon generally produced more carbon than did JP-4 and JP-5 fuels. The deposits were reduced appreciably with a fuel-oil additive. At high-altitude conditions, the high Btu-per-gallon fuels gave lower efficiencies than did JP-4 or JP-5 fuels. No attempts were made to improve performance by combustor design modification.

Jonash, Edmund R↗
NASA NTRS2002

Modes 1 and 4 Testing of an Axisymmetric GTX RBCC Engine

Under sponsorship of the NASA Glenn Research Center (NASA GRC), the Johns Hopkins University Applied Physics Laboratory (JHU/APL) designed and built a five-inch diameter, Rocket-Based Combined Cycle (RBCC) engine to investigate mode 1 and mode 4 performance. This engine was designed so that engine area and length ratios were similar to the NASA GRC GTX engine. Unlike the GTX semi-circular engine design, the APL engine is completely axisymmetric. For this design, a traditional rocket thruster was installed inside of the scramjet flowpath, along the engine centerline. A three part test series is currently underway to determine mode 1 and mode 4 engine performance and compare those results to the rocket thruster operating by itself. All tests are to be conducted in APL's Cell 2 Freejet Engine Facility. Testing of the rocket thruster alone has been accomplished and its performance determined (average Isp efficiency = 90%). Mode 1 (air-augmented rocket) testing is to be conducted at various chamber pressure-to-ambient pressure ratios with the engine inlet fully open. Mode 4 (vacuum rocket) testing is to be conducted with chamber pressure-to-ambient pressure ratios greater than 600 with the inlet fully closed to simulate high-altitude flight conditions. The engine is currently installed in Cell 2 and awaiting testing. This paper discusses the engine design and details the results of the rocket-only testing. Comparisons to previous tests and projected mode 1 and mode 4 test conditions are also discussed.

Rice, Tharen↗
NASA NTRS1952

Thrust Augmentation of a Turbojet Engine at Simulated Flight Conditions by Introduction of a Water-Alcohol Mixture into the Compressor

An investigation was conducted at simulated high-altitude flight conditions to evaluate the use of compressor evaporative cooling as a means of turbojet-engine thrust augmentation. Comparison of the performance of the engine with water-alcohol injection at the compressor inlet, at the sixth stage of the compressor, and at the sixth and ninth stages was made. From consideration of the thrust increases achieved, the interstage injection of the coolant was considered more desirable preferred over the combined sixth- and ninth-stage injection because of its relative simplicity. A maximum augmented net-thrust ratio of 1.106 and a maximum augmented jet-thrust ratio of 1.062 were obtained at an augmented liquid ratio of 2.98 and an engine-inlet temperature of 80 F. At lower inlet temperatures (-40 to 40 F), the maximum augmented net-thrust ratios ranged from 1.040 to 1.076 and the maximum augmented jet-thrust ratios ranged from 1.027 to 1.048, depending upon the inlet temperature. The relatively small increase in performance at the lower inlet-air temperatures can be partially attributed to the inadequate evaporation of the water-alcohol mixture, but the more significant limitation was believed to be caused by the negative influence of the liquid coolant on engine- component performance. In general, it is concluded that the effectiveness of the injection of a coolant into the compressor as a means of thrust augmentation is considerably influenced by the design characteristics of the components of the engine being used.

Useller, James W.↗
NASA NTRS1953

Investigation of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model of the Convair YF-102 Airplane in the Langley Free-Flight Tunnel

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Convair YF-102 airplane has been made in the Langley free-flight tunnel. The model was flown over a lift-coefficient range from 0.5 to the stall in its basic configuration and with several modifications involving leading-edge slats and increases in vertical-tail size. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect of freeing the controls. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the speed range investigated except near the stall, where large values of static directional instability caused the model to be directionally divergent. The addition of leading-edge slats or an 8-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The use of leading-edge slats in combination with a 40-percent increase in vertical-tail size eliminated the directional divergence and produced satisfactory stability characteristics through the stall. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered satisfactory over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Johnson, Joseph L., Jr.↗
NASA NTRS1951

Investigation of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model of the Douglas XF4D-1 Airplane in the Langley Free-Flight Tunnel TED No. NACA DE 349

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Douglas XF4D-1 airplane has been made in the Langley free-flight tunnel. The model was flown with leading-edge slats retracted and extended over a lift-coefficient range from 0.5 to the stall. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect on the stability characteristics of freeing the controls. The longitudinal stability and control characteristics of the model were satisfactory for all conditions investigated except near the stall with slats extended, where the model had a slight nosing-up tendency. The lateral stability and control characteristics of the model were considered satisfactory for all conditions investigated except near the stall with slats retracted, where a change in sign of the static- directional-stability parameter Cn(sub beta) caused the model to be directionally divergent. The addition of an extension to the top of the vertical tail did not increase Cn(sub beta) enough to eliminate the directional divergence of the model, but a large increase in Cn(sub beta) that was obtainable by artificial means appeared to eliminate the divergence and flights near the stall could be made. Artificially increasing the stability derivative-Cn(sub r) (yawing moment due to yawing) and Cn(sub p) (yawing moment due to rolling) had little effect on the divergence for the range of these parameters investigated. Calculations indicate that the damping of the lateral oscillation of the airplane with slats retracted or extended will be satisfactory at sea level but will be only marginally satisfactory at 40,000 feet.

Johnson, Joseph L.↗
NASA NTRS2008

LOX/Methane Main Engine Igniter Tests and Modeling

The LOX/methane propellant combination is being considered for the Lunar Surface Access Module ascent main engine propulsion system. The proposed switch from the hypergolic propellants used in the Apollo lunar ascent engine to LOX/methane propellants requires the development of igniters capable of highly reliable performance in a lunar surface environment. An ignition test program was conducted that used an in-house designed LOX/methane spark torch igniter. The testing occurred in Cell 21 of the Research Combustion Laboratory to utilize its altitude capability to simulate a space vacuum environment. Approximately 750 ignition test were performed to evaluate the effects of methane purity, igniter body temperature, spark energy level and frequency, mixture ratio, flowrate, and igniter geometry on the ability to obtain successful ignitions. Ignitions were obtained down to an igniter body temperature of approximately 260 R with a 10 torr back-pressure. The data obtained is also being used to anchor a CFD based igniter model.

Breisacher, Kevin J.↗
NASA NTRS2016

Space Launch System Base Heating Test: Environments and Base Flow Physics

The NASA Space Launch System (SLS) vehicle is composed of four RS-25 liquid oxygen-hydrogen rocket engines in the core-stage and two 5-segment solid rocket boosters and as a result six hot supersonic plumes interact within the aft section of the vehicle during flight. Due to the complex nature of rocket plume-induced flows within the launch vehicle base during ascent and a new vehicle configuration, sub-scale wind tunnel testing is required to reduce SLS base convective environment uncertainty and design risk levels. This hot-fire test program was conducted at the CUBRC Large Energy National Shock (LENS) II short-duration test facility to simulate flight from altitudes of 50 kft to 210 kft. The test program is a challenging and innovative effort that has not been attempted in 40+ years for a NASA vehicle. This paper discusses the various trends of base convective heat flux and pressure as a function of altitude at various locations within the core-stage and booster base regions of the two-percent SLS wind tunnel model. In-depth understanding of the base flow physics is presented using the test data, infrared high-speed imaging and theory. The normalized test design environments are compared to various NASA semi-empirical numerical models to determine exceedance and conservatism of the flight scaled test-derived base design environments. Brief discussion of thermal impact to the launch vehicle base components is also presented.

Mehta, Manish↗