Search NASA⌕ Search

SEARCH · Search NASA

Results for “Acoustics Noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Effects of multi-element acoustic treatment on compressor inlet noise

An analytic and experimental study was conducted with the objective of developing both a basic understanding of axially segmented inlet acoustic treatment liners, and design procedures for enhancing the suppression of compressor inlet radiated noise. Anechoic chamber measurements demonstrated that the multielement treatment produced significantly more low frequency suppression than uniform treatment. Further, in-duct spinning mode patterns generated by the rotating vehicle were successfully measured and used as input to an analytical prediction procedure, providing significant improvement in inlet suppression predictions. The study indicated that phased inlet liners can be designed to provide increased noise suppression compared to uniform treatment.

Kraft, R. E.↗
NASA NTRS1975

Study of noise sources in a subsonic fan using measured blade pressures and acoustic theory

Sources of noise in a 1.4 m (4.6 ft) diameter subsonic tip speed propulsive fan running statically outdoors are studied using a combination of techniques. Signals measured with pressure transducers on a rotor blade are plotted in a format showing the space-time history of inlet distortion. Study of these plots visually and with statistical correlation analysis confirms that the inlet flow contains long, thin eddies of turbulence. Turbulence generated in the boundary layer of the shroud upstream of the rotor tips was not found to be an important noise source. Fan noise is diagnosed by computing narrowband spectra of rotor and stator sound power and comparing these with measured sound power spectra. Rotor noise is computed from spectra of the measured blade pressures and stator noise is computed using the author's stator noise theory. It is concluded that the rotor and stator sources contribute about equally at frequencies in the vicinity of the first three harmonics of blade passing frequency. At higher frequencies, the stator contribution diminishes rapidly and the rotor/inlet turbulence mechanism dominates. Two parametric studies are performed by using the rotor noise calculation procedure which was correlated with test. In the first study, the effects on noise spectrum and directivity are calculated for changes in turbulence properties, rotational Mach number, number of blades, and stagger angle. In the second study the influences of design tip speed and blade number on noise are evaluated.

Hanson, D. B.↗
NASA NTRS1989

NASA/AHS rotorcraft noise reduction program - NASA Langley Acoustics Division contributions

An account is given of the contributions made by NASA-Langley's rotorcraft noise research programs over the last five years. Attention has been given to the broadband and blade-vortex interaction noise sources; both analytical and empirical noise-prediction codes have been developed and validated for several rotor noise sources, and the 'Rotonet' comprehensive system-noise prediction capability has been instituted. Among the technologies explored for helicopter noise reduction have been higher harmonic control and active vibration-suppression.

Martin, Ruth M.↗
NASA NTRS1995

(abstract) Vibration Damping of the Cassini Spacecraft Structure

Cassini will be protected during launch ascent through the atmosphere by a lightweight aluminum payload fairing (PLF). As a result of the extreme noise levels generated by the powerful Titan IV at liftoff, and the acoustic transparency of the PLF, Cassini is predicted to experience severe acoustic levels. Furthermore, the high acoustic levels, coupled with the size and configuration of the spacecraft, will induce intense random vibration on the structure and critical spacecraft components. Efforts to mitigate the vibroacoustic environment by modifying the spacecraft structure were pursued. Preliminary studies indicated that a structural damping treatment using viscoelastic materials (VEMs) represented a viable technique of reducing vibration with minimum impact on weight, cost, and redesign. Tuned Vibration Absorbers (TVAs) - compact, single degree-of-freedom mechanical oscillators in which a VEM serves as the spring and damping element - will be used also. The operating principles, design, and installation of the TVAs are described, the test program is outlined, and test results are presented which show that significant vibration attenuation was achieved.

vibroacoustic environment↗
NASA NTRS2013

An Overview of Virtual Acoustic Simulation of Aircraft Flyover Noise

Methods for testing human subject response to aircraft flyover noise have greatly advanced in recent years as a result of advances in simulation technology. Capabilities have been developed which now allow subjects to be immersed both visually and aurally in a three-dimensional, virtual environment. While suitable for displaying recorded aircraft noise, the true potential is found when synthesizing aircraft flyover noise because it allows the flexibility and freedom to study sounds from aircraft not yet flown. A virtual acoustic simulation method is described which is built upon prediction-based source noise synthesis, engineering-based propagation modeling, and empirically-based receiver modeling. This source-path-receiver paradigm allows complete control over all aspects of flyover auralization. With this capability, it is now possible to assess human response to flyover noise by systematically evaluating source noise reductions within the context of a system level simulation. Examples of auralized flyover noise and movie clips representative of an immersive aircraft flyover environment are made in the presentation.

Rizzi, Stephen A.↗
NASA NTRS1995

Prediction and Measurement of the Vibration and Acoustic Radiation of Panels Subjected to Acoustic Loading

Interior noise and sonic fatigue are important issues in the development and design of advanced subsonic and supersonic aircraft. Conventional aircraft typically employ passive treatments, such as constrained layer damping and acoustic absorption materials, to reduce the structural response and resulting acoustic levels in the aircraft interior. These techniques require significant addition of mass and only attenuate relatively high frequency noise transmitted through the fuselage. Although structural acoustic coupling is in general very important in the study of aircraft fuselage interior noise, analysis of noise transmission through a panel supported in an infinite rigid baffle (separating two semi-infinite acoustic domains) can be useful in evaluating the effects of active/adaptive materials, complex loading, etc. Recent work has been aimed at developing adaptive and/or active methods of controlling the structural acoustic response of panels to reduce the transmitted noise1. A finite element formulation was recently developed to study the dynamic response of shape memory alloy (SMA) hybrid composite panels (conventional composite panel with embedded SMA fibers) subject to combined acoustic and thermal loads2. Further analysis has been performed to predict the far-field acoustic radiation using the finite element dynamic panel response prediction3. The purpose of the present work is to validate the panel vibration and acoustic radiation prediction methods with baseline experimental results obtained from an isotropic panel, without the effect of SMA.

Turner, Travis L.↗
NASA NTRS1972

Aspects of investigating STOL noise using large scale wind tunnel models

The applicability of the NASA Ames 40- by 80-ft wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind tunnel test section has been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied both in the free-field and wind tunnel acoustic environments. The results indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. Directional microphone and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be discernable from the wind tunnel background noise.

Falarski, M. D.↗
NASA NTRSDate not supplied

Effect of Flight on the Noise from Turbulent Jets in the Generalized Acoustic Analogy

This presents an extension of a noise prediction method for static jets based on the Generalized Acoustic Analogy to include a non-zero ambient stream to simulate the effects of flight. Extended formulae for the propagator functions, source terms and the far-field acoustic spectrum are derived. The formulations of the equation and the boundary conditions for numerical solution of the scalar adjoint Green’s function in the presence of a non-zero ambient stream are also given. Wherever possible, the corresponding equations in the original papers for the static case and their extensions to include a flight stream are identified. The extended formulation is implemented into an existing code and used to make predictions of the effect of the flight stream on the observed far-field noise for a series of subsonic, unheated, axisymmetric jets over a range of jet-exit and free-stream velocities using Reynolds-averaged Navier-Stokes flow solutions as input. The predictions are compared with data from experiments conducted at NASA Glenn Research Center which extend a fundamental jet noise database to include a flight stream of various speeds. Descriptions of the experimental setup, data acquisition, post-processing and corrections applied to account for the external shear-layer are given. It is shown that the acoustic analogy-based method can provide reasonably good predictions of the impact of an external flight stream on the spectral characteristics of noise from unheated round jets.

Jet noise↗
NASA NTRS2002

The Acoustic Analogy and Alternative Theories for Jet Noise Prediction

This paper describes several methods for the prediction of jet noise. All but one of the noise prediction schemes are based on Lighthill's or Lilley's acoustic analogy while the other is the jet noise generation model recently proposed by Tam and Auriault. In all the approaches some assumptions must be made concerning the statistical properties of the turbulent sources. In each case the characteristic scales of the turbulence are obtained from a solution of the Reynolds-averaged Navier Stokes equation using a k - epsilon turbulence model. It is shown that, for the same level of empiricism, Tam and Auriault's model yields better agreement with experimental noise measurements than the acoustic analogy. It is then shown that this result is not because of some fundamental flaw in the acoustic analogy approach: but, is associated with the assumptions made in the approximation of the turbulent source statistics. If consistent assumptions are made, both the acoustic analogy and Tam and Auriault's model yield identical noise predictions. The paper concludes with a proposal for an acoustic analogy that provides a clearer identification of the equivalent source mechanisms and a discussion of noise prediction issues that remain to be resolved.

Morris, Philip J.↗
NASA NTRS2002

The Acoustic Analogy and Alternative Theories for Jet Noise Prediction

This paper describes several methods for the prediction of jet noise. All but one of the noise prediction schemes are based on Lighthill's or Lilley's acoustic analogy while the other is the jet noise generation model recently proposed by Tam and Auriault. In all the approaches some assumptions must be made concerning the statistical properties of the turbulent sources. In each case the characteristic scales of the turbulence are obtained from a solution of the Reynolds-averaged Navier Stokes equation using a k-epsilon turbulence model. It is shown that, for the same level of empiricism, Tam and Auriault's model yields better agreement with experimental noise measurements than the acoustic analogy. It is then shown that this result is not because of some fundamental flaw in the acoustic analogy approach: but, is associated with the assumptions made in the approximation of the turbulent source statistics. If consistent assumptions are made, both the acoustic analogy and Tam and Auriault's model yield identical noise predictions. The paper concludes with a proposal for an acoustic analogy that provides a clearer identification of the equivalent source mechanisms and a discussion of noise prediction issues that remain to be resolved.

Morris, Philip J.↗
NASA NTRS2002

Acoustic Analogy and Alternative Theories for Jet Noise Prediction

Several methods for the prediction of jet noise are described. All but one of the noise prediction schemes are based on Lighthill's or Lilley's acoustic analogy, whereas the other is the jet noise generation model recently proposed by Tam and Auriault. In all of the approaches, some assumptions must be made concerning the statistical properties of the turbulent sources. In each case the characteristic scales of the turbulence are obtained from a solution of the Reynolds-averaged Navier-Stokes equation using a kappa-sigma turbulence model. It is shown that, for the same level of empiricism, Tam and Auriault's model yields better agreement with experimental noise measurements than the acoustic analogy. It is then shown that this result is not because of some fundamental flaw in the acoustic analogy approach, but instead is associated with the assumptions made in the approximation of the turbulent source statistics. If consistent assumptions are made, both the acoustic analogy and Tam and Auriault's model yield identical noise predictions. In conclusion, a proposal is presented for an acoustic analogy that provides a clearer identification of the equivalent source mechanisms, as is a discussion of noise prediction issues that remain to be resolved.

Morris, Philip J.↗
NASA NTRS1973

Aspects of investigating STOL noise using large-scale wind-tunnel models.

The applicability of the NASA Ames 40- by 80-foot wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind-tunnel test section have been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied in both the free-field and wind-tunnel acoustic environments. The results of these studies indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. A directional microphone, a phased array of microphones, and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be distinguishible from the wind-tunnel background noise.

Falarski, M. D.↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design With and Without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design with and without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗
NASA NTRS1977

Aero-acoustic performance comparison of core engine noise suppressors on NASA quiet engine C

The relative aero-acoustic effectiveness of two core engine suppressors, a contractor-designed suppressor delivered with the Quiet Engine, and a NASA-designed suppressor was evaluated. The NASA suppressor was tested with and without a splitter making a total of three configurations being reported in addition to the baseline hardwall case. The aerodynamic results are presented in terms of tailpipe pressure loss, corrected net thrust, and corrected specific fuel consumption as functions of engine power setting. The acoustic results are divided into duct and far-field acoustic data. The NASA-designed core suppressor did the better job of suppressing aft end noise, but the splitter associated with it caused a significant engine performance penality. The NASA core suppressor without the spltter suppressed most of the core noise without any engine performance penalty.

Bloomer, H. E.↗