SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The results of a study of the feasibility of an active method of surface error control using thermal elements are presented. It is shown that the control effort of the thermal elements is sufficient for the purpose, and that such benefits as low cost, low weight, and high reliability may be achieved in conjunction with a significant reduction in the mirror surface error figure.
Application of the aerodynamic energy approach to some problems of flutter suppression and gust alleviation were considered. A simple modification of the control-law is suggested for achieving the required pitch control in the use of a leading edge - trailing edge activated strip. The possible replacement of the leading edge - trailing edge activated strip by a trailing edge - tab strip is also considered as an alternate solution. Parameters affecting the performance of the activated leading edge - trailing edge strip were tested on the Arava STOL Transport and the Westwind Executive Jet Transport and include strip location, control-law gains and a variation in the control-law itself.
Experiments were carried out to study the feasibility of active stabilization of vaneless diffuser rotating stalls. Pressure fluctuation at the diffuser inlet was monitored and used to control the rotating stall. AC control flow, which is produced by a load speaker, was introduced into the diffuser at the inlet. It is shown that the rotating stall can be suppressed when the phase of the control flow has a certain relation with the phase of the rotating stall. By considering the energy flux due to the AC control flow, it is shown that the rotating stall is suppressed when the control flow has the phase such that the energy is subtracted out from the diffuser flow. Discussions are made on the relations between the energy flux and the amplitude of the pressure fluctuation due to the rotating stalls.
Cabin noise in turboprop aircraft causes passenger discomfort, airframe fatigue, and employee scheduling constraints due to OSHA standards for exposure to high levels of noise. The noise levels in the cabins of turboprop aircraft are typically 10 to 30 decibels louder than commercial jet noise levels. However. unlike jet noise the turboprop noise spectrum is dominated by a few low frequency tones. Active structural acoustic control is a method in which the control inputs (used to reduce interior noise) are applied directly to a vibrating structural acoustic system. The control concept modeled in this work is the application of in-plane force inputs to piezoceramic patches bonded to the wall of a vibrating cylinder. The goal is to determine the force inputs and locations for the piezoceramic actuators so that: (1) the interior noise is effectively damped; (2) the level of vibration of the cylinder shell is not increased; and (3) the power requirements needed to drive the actuators are not excessive. Computational experiments for data taken from a computer generated model and from a laboratory test article at NASA Langley Research Center are provided.
A method is presented for simulating the coupled 'electromechanical' system to predict rotordynamic stability and unbalance response along with control system stability. The piezoelectric actuators and their amplifiers are represented as equivalent linear electrical circuits. The electromechanical system modeling approach is utilized to correlate test results from a double overhung rotor rig. The test results also show the effectiveness of the control system for suppressing the unbalance response of two modes using active stiffness and active damping.
Effects on spacecraft ground potential of active emission of charged particles are being investigated through experiments using the ATS-5 and ATS-6 spacecraft. Each spacecraft is equipped with ion engine neutralizers which emit low energy charged particles. Despite great differences in design between the two spacecraft, they attain similar potentials in similar environments. Therefore, effects on spacecraft potential of neutralizer operations can be used to compare the effects of operating the two different neutralizers (hot wire filament and plasma bridge). The neutralizers on both spacecraft were operated in eclipse. Results of these operations are presented and spacecraft responses compared.
The reduction of aircraft cabin sound levels to acceptable values still remains a topic of much research. The use of conventional passive approaches has been extensively studied and implemented. However performance limits of these techniques have been reached. In this project, new techniques for understanding the structural acoustic behavior of aircraft fuselages and the use of this knowledge in developing advanced new control approaches are investigated. A central feature of the project is the Aircraft Fuselage Test Facility at Va Tech which is based around a full scale Cessna Citation III fuselage. The work is divided into two main parts; the first part investigates the use of an inverse technique for identifying dominant fuselage vibrations. The second part studies the development and implementation of active and active-passive techniques for controlling aircraft interior noise.
An overview describing the use of piezoceramic patches in reducing noise in a structural acoustics setting is presented. The passive and active contributions due to patches which are bonded to an Euler-Bernoulli beam or thin shell are briefly discussed and the results are incorporated into a 2-D structural acoustics model. In this model, an exterior noise source causes structural vibrations which in turn lead to interior noise as a result of nonlinear fluid/structure coupling mechanism. Interior sound pressure levels are reduced via patches bonded to the flexible boundary (a beam in this case) which generate pure bending moments when an out-of-phase voltage is applied. Well-posedness results for the infinite dimensional system are discussed and a Galerkin scheme for approximating the system dynamics is outlined. Control is implemented by using linear quadratic regulator (LQR) optimal control theory to calculate gains for the linearized system and then feeding these gains back into the nonlinear system of interest. The effectiveness of this strategy for this problem is illustrated in an example.
The objective of this research was to test vibration suppression (settling time and jitter) of a large space structure (LSS) characterized by low frequency high global vibration modes. Five percent passive damping in a large truss was analyzed, tested and correlated. A representative system article re-target analysis shows that modest levels of passive damping dramatically reduce the control energy required. LSS must incorporate passive damping from the outset. The LSS system performance will not be met by either active or passive damping alone.
Techniques for controlling the generation, growth, and interactions of large coherent structures in turbulent flows are discussed, reviewing the results of recent experimental investigations. The fundamental principles of active and passive coherent-structure manipulation are outlined; the effects of geometric modification are examined for the case of an elliptic jet; and particular attention is given to passive control via self-excitation, turbulence and noise suppression, control of pairing interaction via two-frequency excitation, and unsteady boundary-layer separation in wall jets. Diagrams and graphs of typical results are provided.
Math models were developed for various types of large flexible structures. These models were used to study the uncontrolled dynamic characteristics of the structures in orbit and to devise control concepts in order to control their orientation and geometrical shape. Reduced order decoupled control of the 100 meter long free free beam were studied. The inplane orientation and shape of the beam was controlled in a decoupled manner with as few actuators as possible. Using two controllers, near each end of the beam, to produce a 0.01 radian pitch change, perfect decoupled control was achieved for the rigid body pitch theta mode and the first flexible mode A sub 1.
State variable representations of flexible aircraft are obtained using a modeling approach which first defines a mean-reference axis coordinate system. The active system design approach for forward-swept-wing aircraft also expresses structural deformations of the wing in terms of free normal vibration modes relative to this mean reference axis. Calculations which assume quasi-steady incompressible aerodynamics are performed to obtain generalized force expressions for flight conditions. The use of this quadratic synthesis technique shows that increased performance and redundancy over decentralized approaches can be achieved using integrated active longitudinal stability augmentation and aeroelastic stabilization.
We show that the thermal fluctuations of very soft mechanical oscillators, such as the cantilever in an atomic force microscope (AFM), can be reduced without changing the stiffness of the spring or having to lower the environment temperature. We derive a theoretical relationship between the thermal fluctuations of an oscillator and an actively external-dissipative force. This relationship is verified by experiments with an AFM cantilever where the external active force is coupled through a magnetic field. With simple instrumentation, we have reduced the thermal noise amplitude of the cantilever by a factor of 3.4, achieving an apparent temperature of 25 K with the environment at 295K. This active noise reduction approach can significantly improve the accuracy of static position or static force measurements in a number of practical applications.
The coupling of a vibrating finite elastic cylinder and its interior cavity, closed with rigid end caps, is examined. Results are presented for several types of excitation including a point force, a single external acoustic monopole, and an array of external monopoles. Modal spectra are examined for a frequency range typical of the harmonic noise produced by advanced turbo-props. The effect of frequency and source distribution on modal content is presented. Significant interface modal filtering, which would have a beneficial impact on an active system for reducing interior noise, was found to occur for all cases. Some preliminary experimental data for a stiffened, composite cylinder are presented and discussed.
This paper considers the problem of designing a control system to achieve and maintain the required surface accuracy of the primary mirror of a large space telescope. Control over the mirror surface is obtained through the application of a corrective force distribution by actuators located on the rear surface of the mirror. The design procedure is an extension of a model control technique developed for distributed parameter plants with known eigenfunctions to include plants whose eigenfunctions must be approximated by numerical techniques. Instructions are given for constructing the mathematical model of the system, and a design procedure is developed for use with. typical numerical data in selecting the number and location of the actuators. Examples of actuator patterns and their effect on various errors are given.
Active control of dynamical behavior of rotor systems involves the following modeling of the rotor system including active elements as a control process, positioning of actuators and sensors, implementation of problem-adapted control concepts. The key to attaining the desired influence on the dynamic behavior of rotor systems lies in the presence of suitable actuators. Some types of actuators (magnetic, electrohydraulic and piezoelectric) will be discussed and their respective drawbacks indicated. Their design will be outlined and functional correlations will be presented. Theoretical and experimental results demonstrate that an improvement of the system dynamics by the use of control forces is always possible.
Explore the source record for details and available documents.
Cushioncraft ground effect machine with heave response and control concepts