Search NASA⌕ Search

SEARCH · Search NASA

Results for “Airframes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Experimental evaluation of nacelle-airframe interference forces and pressures at Mach numbers of 0.9 to 1.4

Detailed interference force-and-pressure data were obtained on a representative supersonic transport wing-body-nacelle combination at Mach numbers of 0.9 to 1.4. The basic model consisted of a delta wing-body aerodynamic model with a length of 158.0 cm (62.2 in.) and a wingspan of 103.6 cm (40.8 in.) and four independently supported nacelles positioned beneath the model. The experimental program was conducted in the Ames 11- by 11-Foot Wind Tunnel at a constant unit Reynolds number. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass-flow ratio. Under the most favorable conditions, the net interference drag was equal to 50 percent the drag of four isolated nacelles at M = 1.4, 75 percent at M = 1.15, and 144 percent at M = 0.90. The overall interference effects were found to be rather constant over the operating angle-of-attack range of the configuration. The effects of mass-flow ratio on the interference pressure distributions were limited to the lip region of the nacelle and the local wing surface in the immediate vicinity of the nacelle lip. The net change in the measured interference forces resulting from variations in the nacelle mass-flow ratio were found to be quite small.

Bencze, D. P.↗
NASA NTRS1977

Flow effects with cross-blown lifting jets of V/STOL aircraft and their reactions on aerodynamical forces and moments of the airframe

Systematic basic studies on the close and distant effects of cross blown single and twin lifting jets were performed with the aid of a principle model. The different effects are described in detail. The number of the experimental parameters is reduced to the most essential ones: (1) the angle of attack, (2) the flight and the jet velocities as well as the jet diameter, (3) the distance between the twin jets, (4) the location of the wing relative to the jets and the fuselage, and (5) the ground distance. The results of systematic pressure distribution measurements on the fuselage surface are studied, especially in the close vicinity of the jet exits. From these results, functions on the influence of the parameters are deduced.

Viehweger, G.↗
NASA NTRS1977

Computations in turbulent flows and off-design performance predictions for airframe-integrated scramjets

The research activity focused on two main tasks: (1) the further development of the SCRAM program and, in particular, the addition of a procedure for modeling the mechanism of the internal adjustment process of the flow, in response to the imposed thermal load across the combustor and (2) the development of a numerical code for the computation of the variation of concentrations throughout a turbulent field, where finite-rate reactions occur. The code also includes an estimation of the effect of the phenomenon called 'unmixedness'.

Goglia, G. L.↗
NASA NTRS1977

Airframe noise measurements by acoustic imaging

Studies of the noise produced by flow past wind tunnel models are presented. The central objective of these is to find the specific locations within a flow which are noisy, and to identify the fluid dynamic processes responsible, with the expectation that noise reduction principles will be discovered. The models tested are mostly simple shapes which result in types of flow that are similar to those occurring on, for example, aircraft landing gear and wheel cavities. A model landing gear and a flap were also tested. Turbulence has been intentionally induced as appropriate in order to simulate full-scale effects more closely. The principal technique involves use of a highly directional microphone system which is scanned about the flow field to be analyzed. The data so acquired are presented as a pictorial image of the noise source distribution. An important finding is that the noise production is highly variable within a flow field and that sources can be attributed to various fluid dynamic features of the flow. Flow separation was not noisy, but separation closure usually was.

Kendall, J. M.↗
NASA NTRS1977

An experimental investigation of airframe component interference noise

Measurements of noise produced by a model of a wheel well (rectangular cavity), landing gear (wheel and strut), and flap at Mach numbers of 0.18 and 0.40 have been made in an anechoic flow facility. Individual component noise and component interference noise are described in terms of the OASPL, spectra, and streamwise or flyover directivity patterns. Areas of significant sound generation are illuminated and causes of these noise sources are suggested. Results from an acoustic imaging technique are used to point out other source regions not discernible by simple far-field measurements.

Block, P. J. W.↗
NASA NTRS1978

Propulsion-airframe interactions predictability

An illustration of the possible magnitude of the transonic performance prediction problem is shown. These results derived from a careful and systematic set of tests run on a jet effects model, an aerodynamic and force model, and a pressure model, evaluated test techniques and wind tunnel effects. The results were then carefully compared with flight test data where significant discrepancies in zero-lift drag were observed. A vigorous review of the test techniques identified a number of potential error sources. Some of these were thought to be aircraft roughness and protuberances, tunnel anomalies, sting/model support corrections, and hot gas effects. In addition, there were questions on model metric splitline location and magnitude of corrections for scale and Reynolds number. Flight test inlet/engine characteristics were thought to differ, also, from those of the calibration settings in the ground facilities.

Smith, R. H.↗
NASA NTRS1978

Some aspects of powerplant airframe integration affecting fuel conservation

The performance criteria for STOL transport aircraft place many constraints on engineering design, which, in turn, may have a direct bearing on fuel efficiency: these constraints become even more severe with the introduction of powered-lift for turbofan aircraft. Consideration is given to some aspects of performance and design which arise as a result of powerplant/airframe integration and an attempt is made to assess these factors in terms of transport fuel efficiency. The drag polars of various powered lift concepts are analyzed to determine the installed thrust/weight required and a simple method of relating this to fuel efficiency is suggested. Some other factors have been identified as being important to this aspect of design and these are discussed in more general terms. Finally, special consideration is given to recent Canadian research in the realm of supercritical airfoil technology as applied to an multi-foil section which could be utilized both for the STOL regime of flight and for cruise at transonic speeds.

Farbridge, J. E.↗
NASA NTRS1978

Airframes and aerodynamics

The first part of the paper discusses the Energy Efficient Transport program of the Aircraft Energy Efficiency (ACEE) program, giving attention to the development of active aerodynamics and active controls. The second part of the paper deals with two other portions of the ACEE program: Composite Primary Structures and Laminar Flow Control.

Leonard, R. W.↗
NASA NTRS1978

Effects of inlet airframe integration on the inlet of an upper surface blowing four-engine STOL aircraft

Inlet and nacelle static pressures were measured on a 0.55-scale model of the Quiet Short-Haul Research Airplane (QSRA) in the Ames Research Center's 40- by 80-Foot Wind Tunnel. This model is powered by four JT-15D engines located above the wing with closely spaced adjacent inlets. A fifth JT-15D engine in the fuselage provides boundary-layer control air. Each inlet was instrumented with four to eight rows of axial pressure taps located between X/R approximately plus or minus 1. The tests simulated a broad range of aircraft operating conditions, including engine-out, with lift coefficients from 0.8 to 10.0. Results indicate that the inlets perform well under most operating conditions with little interaction between inlets when the aircraft is moving. Potential problem areas identified are high sideslip angle during approach and an interaction effect between adjacent inlets with high mass flows in static conditions.

Shovlin, M. D.↗
NASA NTRS1979

Hypersonic airframe structures: Technology needs and flight test requirements

Hypersonic vehicles, that may be produced by the year 2000, were identified. Candidate thermal/structural concepts that merit consideration for these vehicles were described. The current status of analytical methods, materials, manufacturing techniques, and conceptual developments pertaining to these concepts were reviewed. Guidelines establishing meaningful technology goals were defined and twenty-eight specific technology needs were identified. The extent to which these technology needs can be satisfied, using existing capabilities and facilities without the benefit of a hypersonic research aircraft, was assessed. The role that a research aircraft can fill in advancing this technology was discussed and a flight test program was outlined. Research aircraft thermal/structural design philosophy was also discussed. Programs, integrating technology advancements with the projected vehicle needs, were presented. Program options were provided to reflect various scheduling and cost possibilities.

Stone, J. E.↗
NASA NTRS1979

Thermal-structural Design Study of an Airframe-integrated Scramjet

Design concepts for the cooled structures assembly for the Langley Scramjet engine, for engine subsystems, and for the aircraft/engine interface were developed and evaluated. Results show that the objectives for the Scramjet engine can be met. A thermal protection system was defined that makes it possible to attain a life of 100 hours and 1000 cycles, which is the specified goal. With stoichiometric combustion, the fuel provides an adequate heat sink for cooling the engine at Mach numbers up to 9 at the minimum fuel flow condition. The mechanical design is feasible for manufacture using conventional materials. For the cooled structures in a six-module engine, the mass per unit capture area is 1328 kg/sq m (259 lb/sq ft). The total mass of a six-module engine assembly including the fuel system is 1577 kg (3477 lb).

Buchmann, O. A.↗
NASA NTRS1978

Recent advances in convectively cooled engine and airframe structures for hypersonic flight

Research over the past decade has identified critical thermal/structural design problems and has produced viable design concepts for a second generation experimental scramjet. The design concepts for the hydrogen fuel-cooled engine structure involve a variety of innovative features to accommodate the harsh aerothermal environment encountered within the engine. The baseline concept which has evolved has reasonable mass characteristics, and cooling requirements which permit engine operation to Mach 9-10 without additional hydrogen for engine cooling. Studies have identified fabrication techniques and coolant passage configurations that increase fatigue life of the structure an order of magnitude over previous configurations.

Kelly, H. N.↗
NASA NTRS1980

Evaluation of approximate methods for the prediction of noise shielding by airframe components

An evaluation of some approximate methods for the prediction of shielding of monochromatic sound and broadband noise by aircraft components is reported. Anechoic-chamber measurements of the shielding of a point source by various simple geometric shapes were made and the measured values compared with those calculated by the superposition of asymptotic closed-form solutions for the shielding by a semi-infinite plane barrier. The shields used in the measurements consisted of rectangular plates, a circular cylinder, and a rectangular plate attached to the cylinder to simulate a wing-body combination. The normalized frequency, defined as a product of the acoustic wave number and either the plate width or cylinder diameter, ranged from 4.6 to 114. Microphone traverses in front of the rectangular plates and cylinders generally showed a series of diffraction bands that matched those predicted by the approximate methods, except for differences in the magnitudes of the attenuation minima which can be attributed to experimental inaccuracies. The shielding of wing-body combinations was predicted by modifications of the approximations used for rectangular and cylindrical shielding. Although the approximations failed to predict diffraction patterns in certain regions, they did predict the average level of wing-body shielding with an average deviation of less than 3 dB.

Ahtye, W. F.↗
NASA NTRS1980

Model tests of airframe noise reduction concepts

Trailing-edge flap and leading-edge slat models were modified to reduce their acoustic response to convected turbulence. These components were tested on an 0.3-m chord wing at 70.7 and 100 m/sec velocities in an acoustic wind tunnel. Noise radiation from the side edges of the 40 deg deflected flap was reduced by use of porous and perforated surface treatment along the leading- and side-edge region. Up to 2 to 3 dB reduction of total flap noise was achieved over a 3-octave range of frequency. Leading-edge slat noise was reduced about 2 dB by use of a perforated trailing-edge region on the slat. These reductions were retained when the modified slat and flaps were tested together.

Fink, M. R.↗
NASA NTRS1981

Airframe effects on top-mounted inlet systems for VSTOL fighter aircraft

Inlet flow-field and compressor-face performance data were obtained for a 0.095-scale model of a VSTOL fighter-attack aircraft configuration with twin top-mounted inlets. Tests were conducted at Mach numbers from 0.6 to 2.0 and at angles of attack and sideslip up to 27 deg and 12 deg, respectively. The effects of inlet location, wing leading-edge extension planform area, canopy-dorsal integration, and variable incidence canards were determined. The results show that distortion at the compressor face when maneuvering is relatively low (20% or less) at Mach numbers up to 0.9. However, at Mach numbers of 1.2 and above, maneuverability may be restricted because of high distortion or low pressure recovery (80% or less) or both.

Smeltzer, D. B.↗
NASA NTRS1982

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet-pressure data were obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top-mounted twin inlets. Data are presented from wind tunnel tests conducted at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27-deg and angles of sideslip up to 12-deg. Trimmed aerodynamic characteristics and inlet performance were compared for three different leading-edge extension (LEX) configurations. The effects of wing leading- and trailing-edge flaps on the inlet were also determined. Maneuver performance was calculated from combined force and inlet-pressure data. The largest of the three LEX sizes tested gave the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗