SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A group of suggested experiments is described, which are to be conducted with ERTS-A and high altitude aircraft imagery during the 1972 period. Methods of analysis and observation of land use, urban change, transportation, and possible pollution, using small scale, low resolution data, are discussed.
For abstract, see volume 1 N77-12634.
For abstract, see volume 1 N77-12634.
A test rig designed to measure stiffness and damping of elastomer cartridges under a rotating load excitation is described. The test rig employs rotating unbalance in a rotor which runs to 60,000 RPM as the excitation mechanism. A variable resonant mass is supported on elastomer elements and the dynamic characteristics are determined from measurements of input and output acceleration. Five different cartridges are considered: three of these are buttons cartridges having buttons located in pairs, with 120 between each pair. Two of the cartridges consist of 360 elastomer rings with rectangular cross-sections. Dynamic stiffness and damping are measured for each cartridge and compared with predictions at different frequencies and different strains.
A method has been presented for measuring the acoustic properties of an absorbent material and a duct/nozzle system (with or without airflow) using a high voltage spark discharge as an impulse source of sound. The cross-spectra of the incident, reflected and transmitted acoustic pressure transients are analyzed by way of a FFT digital processor in the form of complex transfer functions. These transfer functions have a direct relationship to the termination impedance and radiation directivity. The impulse method has been justified by comparisons, with data obtained from existing methods (both experimental and theoretical), that show excellent agreement. Reflection coefficients and radiation impedances of various duct-nozzle systems and their associated far-field directivities are also presented as some of the applications of the impulse technique.
Important features of the Eigensystem Realization Algorithm (ERA) are summarized as follows: (1) from the computational standpoint, the algorithm is attractive, since only simple numerical operations are needed; (2) the computational procedure is numerically stable; (3) the structural dynamics requirements for modal parameter identification and the control design requirements for a reduced-state space model are satisfied; (4) data from more than one test can be used simultaneously to efficiently identify the closely spaced eigenvalues; and (5) no restrictions on number of measurements are imposed.
The Space Transportation System (STS) is a complex and expensive flight system intended to carry unique payloads into low Earth orbit and return. A catastrophic failure, such as STS 51-L, resulted in the loss of both human life as well as expensive and unique hardware. The impact of this incident reaffirms the need to do everything possible to ensure the integrity and reliability of STS. One means of achieving this goal is to expand the number of inspection technologies available. Reported here is the evaluation of the use of modal analysis and test techniques for the purpose of assessing the structural integrity of STS components for which Marshall Space Flight Center has responsibility. This entailed reviewing existing literature and developing a low-level experimental program determine the feasibility of using this technology for structural fault detection.
The Space Transportation System (STS) is a very complex and expensive flight system which is intended to carry payloads into low Earth orbit and return. A catastrophic failure of the STS (such as experienced in the 51-L incident) results in the loss of both human life as well as very expensive hardware. One impact of this incident was to reaffirm the need to do everything possible to insure the integrity and reliability of the STS is sufficient to produce a safe flight. One means of achieving this goal is to expand the number of inspection technologies available for use on the STS. The purpose was to begin to evaluate the possible use of assessing the structural integrity of STS components for which Marshall Space Flight Center (MSFC) has responsibility. This entailed reviewing the available literature and determining a low-level experimental program which could be performed by MSFC and would help establish the feasibility of using this technology for structural fault detection.
The objectives are the following: (1) to plan a tour of local manufacturing facility to observe hardness testing methods used and how they support the manufacturing process today; (2) to learn the operation of Brinell Hardness Testing and equipment set up with samples of accessory equipment for testing of various materials; (3) to use a Brinell scope (hand magnifier) to measure the diameter of the test indentation (in millimeters); (4) to use the hardness equation to determine the spherical area of the indentation and the calculation of the Brinell Hardness Number; (5) to use standard charts for ASTM standard size indenters to find the hardness number; and (6) to learn a method of conversion of the Brinell number to other hardness scales, their common usage, and also to convert the hardness number to the approximate tensile strength.
Explore the source record for details and available documents.
The use of molecular adsorbers, in order to aid in the reduction of the spacecraft contamination levels, is discussed. Molecular adsorbers are characterized by an extremely large surface area, molecularly-porous substructure, and processing charged sites capable of retaining molecular contaminant species. Molecular adsorbers were applied on two Hubble Space Telescope servicing missions, as well as on the tropical rainfall measuring mission. The use of molecular adsorbers carries the potential for low cost, easy fabrication and integration of reliable means for reducing the contamination level around spacecraft.
The authors describe challenging use-cases for Automatic Test Markup Language (ATML), and evaluate solutions. The first case uses ATML Test Results to deliver active features to support test procedure development and test flow, and bridging mixed software development environments. The second case examines adding attributes to Systems Modelling Language (SysML) to create a linkage for deriving information from a model to fill in an ATML document set. Both cases are outside the original concept of operations for ATML but are typical when integrating large heterogeneous systems with modular contributions from multiple disciplines.
No abstract available
No abstract available
NASA’s space missions demand better and more efficient carbon dioxide removal systems. wo challenges present themselves in improving the state of the art pellet adsorption beds: power minimization and uniform heating for carbon dioxide desorption. Titanium heat pipes and vapor chambers were found to be excellent candidates in solving these problems because of their passive heating nature, tolerance to high temperatures, and capability of direct implementation into these adsorbent beds.This research work compares these different titanium heat pipes (HPs) and vapor chambers (VPs).