Search NASA⌕ Search

SEARCH · Search NASA

Results for “CIRCULAR CONFIGURATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

SU-E-T-605: A New Design for a Rotating Gamma Knife. Monte Carlo Simulation

Purpose: to determine the characteristics of the 60Co beam emerging from a new design of a rotating Gamma Knife system and to calculate 3D dose distributions at the isocenter for different source configurations and collimator openings. Methods: We employed the BEAM-Monte Carlo code to realistically model the geometry design, including 30 60Co source capsules, two circular primary collimators (diameter of 6.6mm and 6.1mm) and four different changeable collimators. The shielding of the head design was also simulated. The sources (2.8mm diameter) are distributed in six groups in the spherical geometry. Each source is individually collimated to obtained four different circular fields at the isocenter (3mm, 3.5mm, 6mm and 8mm).The phase-space particles reaching the scoring plane below the primary collimation assembly were recorded and the BEAMDP code was used to determine the fluence and energy spectra of the particles emerging from each source-collimator configuration. The dose distributions at the isocenter plane (397.6mm from the source) were calculated in a spherical component module for the circular field sizes studied. Results: The energy spectra below the head assembly and primary collimators have been obtained, which exhibited the typical 60Co peaks and a small low-energy tail due to scattered photons (from about 200keV to 1MeV). The scattered component of the spectra represents about 8 % of the total number of photons reaching the scoring plane. The radial photon fluence does not vary significantly inside the collimator openings. The spectra of particles from different source groups are compared. Conclusion: The 60Co beam emerging from each source configuration was characterized, which can be used to establish a generic source model for all the sources for fast MC dose calculation. Further investigations are needed to determine the dose variations as a result of partial switching on/off different groups of sources for advanced Gamma Knife SRS/SBRT planning.

07 ISOTOPE AND RADIATION SOURCES↗

Measurement of the Circular Dichroism of Electronic Transitions

This chapter describes the measurement of circular dichroism (CD) for absorption due to transitions between two distinct electronic states. This is distinguished from absorption of lower energy photons, which are associated with changes of only the vibrational modes of the absorber and from the absorption of higher energy photons, which may result in ionizations. From the instrumental viewpoint, the chapter describes the measurement of CD that can be recorded using a photomultiplier or avalanche photodiode to quantify the intensity of a light beam, a photoelastic modulator to periodically alter the beam's polarization, and a monochromator located between the light source and the modulator. Using either criterion, the focus is on the spectral domain spanning about a decade in wavelength (photon energy) from roughly 1.2 {micro}m (1 eV {approx} 160 zJ) in the near infrared to 120 nm (10 eV {approx} 1.6 aJ) in the vacuum ultraviolet (VUV). In the near infrared, there is overlap between the domain of electronic and purely vibrational transitions, the use of photomultipliers or avalanche photodiodes versus solid state detectors and dispersive versus Fourier-transform spectrometers. There is also some overlap in the VUV with synchrotron beamlines that use arrays of magnets called 'insertion devices' to cause the emitted synchrotron radiation to be elliptically polarized. To my knowledge, no single spectrometer spans this entire spectral domain discussed here, and the vast majority of laboratory instruments come nowhere close to either the upper or lower limit. However, similar analytical approaches and types of instrumentation are employed throughout this spectral domain and thus are logically treated together. The focus in this chapter is on the measurement of CD resulting from the inherent chirality of the absorbing system. Several spectroscopic methods that are closely related in terms of science or instrumentation are treated in other chapters. These include magnetic circular dichroism (MCD), linear dichroism (LD), optical rotary dispersion (ORD), fluorescence detected circular dichroism (FDCD), and circularly polarized luminescence (CPL). A basic CD instrument of the type described here can be configured by temporary alterations of the sample compartment, an additional or repositioned detector and modified electronics to perform many of the important experiments in the visible and UV regions. These include unpolarized absorption and total fluorescence in addition to most of the experiments mentioned above. Except for absorption, such extensions of the basic technology will not be discussed here. Other reviews of instrumentation related to CD have appeared, some containing information complementary to that included here.

43 PARTICLE ACCELERATORS↗

Fundamental Study of a 7-Element Fuel Injector Configuration for Gas Turbine Combustors - A Look at Cold Flow and Burning Measurements

Lean direct injection (LDI) is a combustion concept to reduce oxides of nitrogen (NOx) for next generation aircraft gas turbine engines. These newer engines have cycles that increase fuel efficiency through increased operating pressures, which increase combustor inlet temperatures. NOx formation rates increase with higher temperatures, and the LDI strategy is to avoid high temperature by staying fuel lean and away from stoichiometric burning. Thus, LDI relies on rapid and uniform fuel/air mixing. Additionally, in combustors for smaller core engines, the area and volume bring about mixing and time scale challenges not found in larger engines. As part of our parametric study in which we vary swirler angle and orientation and look at their effect on fluid mixing and combustion, we examine one configuration of a 7-point lean direct injector by looking at the non-combusting 2-D velocity field using PIV, and combusting system for chemical species using chemiluminescent imaging and flame spectroscopy. The circular 7-point array consists of axial swirlers, with the center 60° swirler surrounded by six 52° swirlers. The velocity results for this configuration show that the outer swirlers serve to isolate the center flow field near the injector exit. A recirculation zone forms downstream of the center swirler, but not behind the outer swirlers. The combusting results also show an isolated zone directly downstream of the center injector. The flame spectra show variation in speciation of combustion species such as OH*, C3*, CH*, and C2* as a function of position within the combustor.

lean direct injection↗

An atomic orbital based real-time time-dependent density functional theory for computing electronic circular dichroism band spectra

One of the challenges of interpreting electronic circular dichroism (ECD) band spectra is that different states may have different rotatory strength signs, determined by their absolute configuration. If the states are closely spaced and opposite in sign, observed transitions may be washed out by nearby states, unlike absorption spectra where transitions are always positive additive. To accurately compute ECD bands, it is necessary to compute a large number of excited states, which may be prohibitively costly if one uses the linear-response time-dependent density functional theory (TDDFT) framework. Here we implement a real-time, atomic-orbital based TDDFT method for computing the entire ECD spectrum simultaneously. The method is advantageous for large systems with a high density of states. In contrast to previous implementations based on real-space grids, the method is variational, independent of nuclear orientation, and does not rely on pseudopotential approximations, making it suitable for computation of chiroptical properties well into the X-ray regime.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigations of Spacecraft Orbits Around the L(2) Sun-Earth Libration Point

Space agencies are planning missions to the vicinity of the Sun-Earth L sub 2 point, some involving a distributed system of telescope spacecraft, configured in a plane about a hub. An improved understanding is developed of their relative motion. First, the telescope equations of motion are written relative to L sub 2 in the context of the classical circular restricted three-body problem, and expanded in terms of the distance from L sub 2. A basic examination is presented of the spacecraft configuration requirements and effects of small orbit insertion errors. Next, the telescope equations of motion relative to the hub are written and further expanded in terms of the hub-L sub 2 and hub-telescope distances. An analytical solution is developed and a halo telescope orbit investigated, with appropriate initial conditions. Then, the force model is extended to include perturbations to an accuracy of 10 to 20 m, east as additive contributions to the circular restricted problem. Perturbations include Earth's orbital eccentricity, lunar motion, solar radiation pressure, and small thrusting forces. Simulations are presented, along with solution sensitivity to errors in hub position knowledge.

RELATIVE MOTION↗

Acoustic investigation of the engine-over-the-wing concept using a D-shaped nozzle

Small-model experiments were conducted of the engine-over-the-wing concept using a D-shaped nozzle in order to determine the static-lift and acoustic characteristics at two wing-flap positions. Configurations were tested with the flow attached and unattached to the upper surface of the flaps. Attachment was obtained with a nozzle flow deflector. In both cases, high frequency noise shielding by the wing was obtained. Configurations using the D-shaped nozzle are compared with corresponding ones using a circular nozzle. With flow attached to the flaps, the static lift and acoustic results are almost the same for both nozzles. Without the nozzle flow deflector, (unattached flap flow), the D-nozzle is considerably noisier than a circular nozzle in the low and middle frequencies.

Reshotko, M.↗

Acoustic investigation of the engine-over-the-wing concept using a D-shaped nozzle.

Small-model experiments were conducted of the engine-over-the-wing concept using a D-shaped nozzle in order to determine the static-lift and acoustic characteristics at two wing-flap positions. Configurations were tested with the flow attached and unattached to the upper surface of the flaps. Attachment was obtained with a nozzle flow deflector. In both cases, high frequency noise shielding by the wing was obtained. Configurations using the D-shaped nozzle are compared with corresponding ones using a circular nozzle. With flow attached to the flaps, the static lift and acoustic results are almost the same for both nozzles. Without the nozzle flow deflector (unattached flap flow), the D-nozzle is considerably noisier than a circular nozzle in the low and middle frequencies.

Reshotko, M.↗

Evaluation of Aircraft Platforms for SOFIA by Computational Fluid Dynamics

The selection of an airborne platform for the Stratospheric Observatory for Infrared Astronomy (SOFIA) is based not only on economic cost, but technical criteria, as well. Technical issues include aircraft fatigue, resonant characteristics of the cavity-port shear layer, aircraft stability, the drag penalty of the open telescope bay, and telescope performance. Recently, two versions of the Boeing 747 aircraft, viz., the -SP and -200 configurations, were evaluated by computational fluid dynamics (CFD) for their suitability as SOFIA platforms. In each configuration the telescope was mounted behind the wings in an open bay with nearly circular aperture. The geometry of the cavity, cavity aperture, and telescope was identical in both platforms. The aperture was located on the port side of the aircraft and the elevation angle of the telescope, measured with respect to the vertical axis, was 500. The unsteady, viscous, three-dimensional, aerodynamic and acoustic flow fields in the vicinity of SOFIA were simulated by an implicit, finite-difference Navier-Stokes flow solver (OVERFLOW) on a Chimera, overset grid system. The computational domain was discretized by structured grids. Computations were performed at wind-tunnel and flight Reynolds numbers corresponding to one free-stream flow condition (M = 0.85, angle of attack alpha = 2.50, and sideslip angle beta = 0 degrees). The computational domains consisted of twenty-nine(29) overset grids in the wind-tunnel simulations and forty-five(45) grids in the simulations run at cruise flight conditions. The maximum number of grid points in the simulations was approximately 4 x 10(exp 6). Issues considered in the evaluation study included analysis of the unsteady flow field in the cavity, the influence of the cavity on the flow across empennage surfaces, the drag penalty caused by the open telescope bay, and the noise radiating from cavity surfaces and the cavity-port shear layer. Wind-tunnel data were also available to compare to the CFD results; the data permitted an assessment of CFD as a design tool for the SOFIA program.

Klotz, S. P.↗

A Cassegrain Offset-Fed Dual-Band Reflectarray

An X/Ka dual-band microstrip reflectarray with circular polarization (CP) has been constructed using thin membranes and Cassegrain offset-fed configuration. It is believed that this is the first Cassegrain reflectarray ever been developed. This antenna has a 75-cm-diameter aperture and uses metallic subreflector and angular-rotated annular ring elements. It achieved a measured -3dB-gain bandwidth of 700 MHz at X-band and 1.5 GHz at Ka-band, as well as a CP bandwidth (3dB axial ratio) of more than 700 MHz at X-band and more than 2 GHz at Ka-band. The measured peak efficiencies are 49.8% at X-band and 48.2% at Ka-band.

offset fed↗

Spin-orbit Resonance and Stability in Eccentric, Low Altitude Mars Orbits

Low altitude orbit perturbations derive from mass concentrations and show high sensitivity to spin-orbit resonance conditions and initial configuration relative to the central body. Here we focus on low, polar, non-circular orbits of Mars. The method uses analytical derivations to identify regimes of interest and computational modeling and graphical design aids for detailed investigation. Evaluation of spin-orbit resonance and gravity perturbation effects are important in mission design applications.The obtained results indicate the presence of unstable regions to avoid for potential future Mars orbiters.

Andres Perez↗

Phase Coexistence and Kinetic Arrest in the Magnetostructural Transition of the Ordered Alloy FeRh

In materials where two or more ordering degrees of freedom are closely matched in their free energies, coupling between them, or multiferroic behavior can occur. These phenomena can produce a very rich phase behavior, as well as emergent phases that offer useful properties and opportunities to reveal novel phenomena in phase transitions. The ordered alloy FeRh undergoes an antiferromagnetic to ferromagnetic phase transition at ~375 K, which illustrates the interplay between structural and magnetic order mediated by a delicate energy balance between two configurations. We have examined this transition using a combination of high-resolution x-ray structural and magnetic imaging and comprehensive x-ray magnetic circular dichroism spectroscopy. We find that the transition proceeds via a defect-driven domain nucleation and growth mechanism, with significant return point memory in both the structural and magnetic domain configurations. In conclusion, the domains show evidence of inhibited growth after nucleation, resulting in a quasi- 2nd order temperature behavior.

36 MATERIALS SCIENCE↗

Domain imaging on multiferroic BiFeO{sub 3}(001) by linear and circular dichroism in threshold photoemission

We demonstrate ferroelectric domain imaging at BiFeO{sub 3}(001) single crystal surfaces with laser-based threshold photoemission electron microscopy (PEEM). Work function differences and linear dichroism allow for the identification of the eight independent ferroelectric domain configurations in the PEEM images. There, the determined domain structure is consistent with piezoresponse force microscopy of the sample surface and can also be related to the circular dichroic PEEM images. Our results provide a method for efficient mapping of complex ferroelectric domains with laser-excited PEEM and may allow lab-based time-resolved studies of the domain dynamics in the future.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A geometric analysis of surface deformation - Implications for the tectonic evolution of Ganymede

The identification of various types of surface deformation of Ganymede by a geometric study of the furrow system and an analysis of circularity of impact craters is addressed. The hypothesis that the furrow system was initially concentric and that the present configuration of the furrows provides a measure of lateral motion of dark terrain is tested by determining the present centers of the furrow system in several dark terrain blocks and observing the amount of deformation in bright terrain regions which separate these blocks. An upper scale limit is placed on the amount of extension associated with bright terrain formation by using the deviation from circularity of impact craters to calculate the strain field around wedge-shaped regions of bright terrain. Penetrative deformation in Ganymede's lithosphere is identified by examining the circularity of impact craters in dark terrain.

Zuber, M. T.↗

Calculation of static longitudinal aerodynamic characteristics of STOL aircraft with upper surface blown flaps

An existing prediction method developed for EBF aircraft configurations was applied to USB configurations to determine its potential utility in predicting USB aerodynamic characteristics. An existing wing-flap vortex-lattice computer program was modified to handle multiple spanwise flap segments at different flap angles. A potential flow turbofan wake model developed for circular cross-section jets was used to model a rectangular cross-section jet wake by placing a number of circular jets side by side. The calculation procedure was evaluated by comparison of measured and predicted aerodynamic characteristics on a variety of USB configurations. The method is limited to the case where the flow and geometry of the configuration are symmetric about a vertical plane containing the wing root chord. Comparison of predicted and measured lift and pitching moment coefficients were made on swept wings with one and two engines per wing panel, various flap deflection angles, and a range of thrust coefficients. The results indicate satisfactory prediction of lift for flap deflections up to 55 and thrust coefficients less than 2. The applicability of the prediction procedure to USB configurations is evaluated, and specific recommendations for improvements are discussed.

Mendenhall, M. R.↗

Manipulation of magnetic state in nanostructures by perpendicular anisotropy and magnetic field

We investigate the transitions of spin configurations in ultrathin nanostructures by tuning the perpendicular anisotropy (K{sub z}) and out-of-plane magnetic field (H), using the Monte Carlo simulation. It is revealed that enhancing the anisotropy K{sub z} can drive the evolution of in-plane vortex state into intriguing saturated magnetization states under various H, such as the bubble domain state and quadruple-block-domain state etc. The spin configurations of these states exhibit remarkable H-dependence. In addition, the strong effects of geometry and size on the spin configurations of nanostructures are observed. In particular, a series of edged states occur in the circular disk-shaped lattices, and rich intricate saturated magnetization patterns appear in big lattices. It is suggested that the magnetic states can be manipulated by varying the perpendicular anisotropy, magnetic field, and geometry/size of the nanostructures. Furthermore, the stability (retention capacity) of the saturated magnetization states upon varying magnetic field is predicted, suggesting the potential applications of these saturated magnetization states in magnetic field-controlled data storages.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Voltage-induced magnetic domain evolution in a phase-change material

Applying voltage to metal–insulator transition (MIT) materials allows electrical actuation of the local electronic phase state. In MIT systems that have the electronic order coupled with the magnetic order, voltage switching of the electronic phase state can also enable the electrical manipulation of magnetic properties. In this work, we utilized x-ray magnetic circular dichroism photoemission electron microscopy (XMCD-PEEM) to investigate the control of magnetic domain configurations in ferromagnetic MIT electrical switches. For applied voltages above a threshold value, the XMCD-PEEM images show that the magnetic domains separate into two distinct regions: one with a high contrast (white/black), indicating well-defined micrometer-scale magnetic domains with a component of their magnetization aligned parallel/antiparallel to the x-ray helicity, and the other with different shades of intermediate contrast (gray). Significant changes in magnetic domain configurations upon voltage biasing were only observed in these gray regions. Furthermore, the voltage-induced magnetic domain separation was found to be bias polarity-dependent, with the gray regions expanding from the opposite sample edge when the applied voltage polarity was reversed. This polarity-dependent electrical control of magnetic domain configurations during the MIT switching opens alternative opportunities in memory applications for magnetic MIT switching materials.

42 ENGINEERING↗

Microwave absorption properties of permalloy nanodots in the vortex and quasi-uniform magnetization states

When the in-plane bias magnetic field acting on a flat circular magnetic dot is smaller than the saturation field, there are two stable competing magnetization configurations of the dot: the vortex and the quasi-uniform (C-state). We measured microwave absorption properties in an array of non-interacting permalloy dots in the frequency range 1-8 GHz when the in-plane bias magnetic field was varied in the region of the dot magnetization state bi-stability. We found that the microwave absorption properties in the vortex and quasi-uniform stable states are substantially different, so that switching between these states in a fixed bias field can be used for the development of reconfigurable microwave magnetic materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Haloes gone MAD14: The Halo-Finder Comparison Project

We present a detailed comparison of fundamental dark matter halo properties retrieved by a substantial number of different halo finders. These codes span a wide range of techniques including friends-of-friends, spherical-overdensity and phase-space-based algorithms. We further introduce a robust (and publicly available) suite of test scenarios that allow halo finder developers to compare the performance of their codes against those presented here. This set includes mock haloes containing various levels and distributions of substructure at a range of resolutions as well as a cosmological simulation of the large-scale structure of the universe. All the halo-finding codes tested could successfully recover the spatial location of our mock haloes. They further returned lists of particles (potentially) belonging to the object that led to coinciding values for the maximum of the circular velocity profile and the radius where it is reached. All the finders based in configuration space struggled to recover substructure that was located close to the centre of the host halo, and the radial dependence of the mass recovered varies from finder to finder. Those finders based in phase space could resolve central substructure although they found difficulties in accurately recovering its properties. Through a resolution study we found that most of the finders could not reliably recover substructure containing fewer than 30–40 particles. However, also here the phase-space finders excelled by resolving substructure down to 10–20 particles. By comparing the halo finders using a high-resolution cosmological volume, we found that they agree remarkably well on fundamental properties of astrophysical significance (e.g. mass, position, velocity and peak of the rotation curve). We further suggest to utilize the peak of the rotation curve, vmax, as a proxy for mass, given the arbitrariness in defining a proper halo edge.

Astronomy & Astrophysics↗