Search NASA⌕ Search

SEARCH · Search NASA

Results for “CUTTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Interactive cutting path analysis programs

The operation of numerically controlled machine tools is interactively simulated. Four programs were developed to graphically display the cutting paths for a Monarch lathe, Cintimatic mill, Strippit sheet metal punch, and the wiring path for a Standard wire wrap machine. These programs are run on a IMLAC PDS-ID graphic display system under the DOS-3 disk operating system. The cutting path analysis programs accept input via both paper tape and disk file.

Weiner, J. M.↗

Ensuring flat cuts in longwall mining

Minicomputer-controlled towed vehicle automatically determines flatness of wall of coal or other mineral as it is being cut by mining machine and allows machine operator to correct cut as necessary. Vehicle is used for longwall mining.

Campbell, R. A.↗

Cutting silicon for solar cells

Multiple bandsaw blades are used to produce multiple cuts on several silicon boules simultaneously, method faster and more reliable than using single saw or multiple-cut reciprocating-blades.

Collins, E. R.↗

Cutting holes in fabric-faced panels

Tool has 2 carbide inserts that bore clean holes through fibrous material with knifelike slicing action. Cutting edge of insert is curved, with plane inner surface at 30 degree angle to tool axis. Drill press or hand-held drill can be used to hold cutting tool.

Peterson, S. A.↗

Effect of inflow control on inlet noise of a cut-on fan

The control of turbulence and other inflow disturbances in anechoic chambers for static turbofan noise studies was studied. A cut-on, high tip speed fan stage was acoustically tested with three configurations of an inflow control device in an anechoic chamber. Although this was a cut-on design, rotor inflow interaction appeared to be a much stronger source of blade passing tone radiated from the inlet than rotor stator interaction for the 1.6 mean rotor chord separation. Aft external suction applied to the area where the inflow control device joined the inlet produced a further reduction in blade passing tone, suggesting that disturbances in the forward flow on the outside of the inlet were superimposed on the inlet boundary layer and were a significant source of tone noise.

Woodward, R. P.↗

Small forest cuttings mapped with Landsat digital data

The Cooperative Landsat Applications Research Group used computer classification of Landsat digital data to map forest cuttings (clearcuts) in northern New Hampshire. Cuttings as small as 3 hectares were identified. Several ages or conditions of clearcuts could be distinguished. Progress in two methods of duplicating classification categories from one Landsat pass to another are discussed. One method was used in making maps of areas in 1973, 1975, and 1978.

Bryant, E.↗

Effect of inflow control on inlet noise of a cut-on fan

A cut-on, high tip speed fan stage was acoustically tested with three configurations of an inflow control device in the NASA Lewis anechoic chamber. Although this was a cut-on design, rotor-inflow interaction appeared to be a much stronger source of blade passing tone radiated from the inlet than rotor-stator interaction for the 1.6 mean rotor chord separation. Aft external suction applied to the area where the inflow control device joined the inlet produced a further reduction in blade passing tone suggesting that disturbances in the forward flow on the outside of the inlet were superimposed on the inlet boundary layer and were a significant source of tone noise.

Woodward, R. P.↗

Design, fabrication and test of last cut Follower

An optical device for following the cut in mining operations is described, and the results of acceptance testing reported. A measuring accuracy of + or - 1/16 inch was demonstrated. Preliminary results on longwall testing with the device mounted on a shearer are presented. Roof profiles measured during tramming and during cutting are presented. Comparison of acoustic measurements with optical measurement of the roof profiles indicates close agreement.

Ashley, P. R.↗

High-temperature measurements of Q-factor in rotated X-cut quartz resonators

The Q-factors of piezoelectric resonators fabricated from natural and synthetic quartz with a 34 deg rotated X-cut orientation were measured at temperatures up to 325 C. The synthetic material, which was purified by electrolysis, retains a higher enough Q to be suitable for high temperature pressure-transducer applications, whereas the natural quartz is excessively lossy above 200 C for this application. The results are compared to results obtained previously at AT-cut resonators.

Fritz, I. J.↗

AK-cut crystal resonators

Calculations have predicted the existence of crystallographically doubly rotated quartz orientations with turnover temperatures which are considerably less sensitive to angular misorientation then comparable AT- or BT-cuts. These crystals are arbitrarily designated as the AK-cut. Experimental data is given for seven orientations, phi-angle variations between 30-46 deg and theta-angle variations between 21-28 deg measured on 3.3-3.4 MHz fundamental mode resonators vibrating in the thickness shear c-mode. The experimental turnover temperatures of these resonators are between 80 C and 150 C, in general agreement with calculated values. The normalized frequency change as a function of temperature has been fitted with a cubic equation.

Kahan, A.↗

Automatically Dressing Blades in Silicon-Wafer Cutting

Inserts incorporated in support beams for silicon ingots automatically "dress" cutting blade during wafer slicing. Segments of blade-dressing material placed at regular intervals in graphite beam. Blade cuts into segments and dressed without operator intervention and without interrupting regular machine operation. Manual dressing eliminated, and production rates increased.

Morrison, A. D.↗

Cut-off rate calculations for the outer channel in a concatenated cooling system

Concatenated codes were long used as a practical means of achieving long block or constraint lengths for combating errors on very noisy channels. The inner and outer encoders are normally separated by an interleaver, so that decoded error bursts coming from the inner decoder are randomized before entering the outer decoder. The effectiveness of this interleaver is examined by calculating the cut-off rate of the outer channel seen by the outer decoder with and without interleaving. Interleaving never hurts the performance of a concatenated code, and when the inner code rate is near the cut-off rate of the inner channel, interleaving significantly improves code performance.

Herro, M. A.↗

Diurnal variations of cosmic ray geomagnetic cut-off threshold rigidities

The spectrographic global survey method was used to investigate the rigidity variations Rc of geomagnetic cut-off as a function of local time and the level of geomagnetic disturbance for a number of stations of the world wide network. It is shown that geomagnetic cut-off threshold rigidities undergo diurnal variations. The diurnal wave amplitude decreases with increasing threshold rigidity Rc, and the wave maximum occurs at 2 to 4 hr LT. The amplitude of diurnal variations increases with increasing geomagnetic activity. The results agree with those from trajectory calculations made for an asymmetric model of the magnetosphere during different geomagnetic disturbance conditions.

Dvornikov, V. M.↗

Material for Fast Cutting

New material for cutting tools increases productivity of machining processes. Material, called Iscanite (or equivalent), based on silicon nitride contains more than 90 percent silicon. Combines impact resistance close to that of coated carbides with heat and wear resistance close to those of aluminum oxide ceramics. Material used for cutting on old or new machine tools and makes it possible to exploit fully power and speed of machine.

Perez, A.↗

Cutting head for ultrasonic lithotripsy

A cutting head for attachment to the end of the wire probe of an ultrasonic kidney stone disintegration instrument is described. The cutting head has a plurality of circumferentially arranged teeth formed at one end thereof to provide a cup shaped receptacle for kidney stones encountered during the disintegration procedure. An integral reduced diameter collar diminishes stress points in the wire and reduce breakage thereof.

Anguluo, E. D.↗

Cutting Symmetrical Recesses In Soft Ceramic Tiles

Simple tool cuts hemispherical recesses in soft ceramic tiles. Designed to expose wires of thermocouples embedded in tiles without damaging leads. Creates neat, precise holes around wires. End mill includes axial hole to accommodate thermocouple wires embedded in material to be cut. Wires pass into hole without being bent or broken. Dimensions in inches. Used in place of such tools as dental picks, tweezers, spatulas, and putty knives.

Nesotas, Tony C.↗