SEARCH · Search NASA

Results for “Combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1963

Ninth Symposium (International) on Combustion

The Ninth Symposium (International) on Combustion was held at Cornell University, Ithaca, New York, August 27 to September 1, 1962, under the auspices of the Combustion Institute. Registration was in excess of 600, with more than 100 attending from Australia, Belgium, Canada, France, Germany, Great Britain, Hungary, Israel, Italy, Japan, Netherlands, Spain and Sweden. Over 200 papers were submitted for consideration, of which 121 were placed on the program and 108 printed in the Proceedings. Two Discussions (Detonations, organized by Dr. D. R. White, General Electric Research Laboratory; Fundamental Flame Processes, organized by Dr. W. H. Avery, APL/The Johns Hopkins University) occupied 4 half-day sessions each. Preprints of all Discussions papers were available several weeks prior to the Symposium. Three Colloquia (Modeling Principles, organized by Professor D. 13. Spalding, Imperial College; Reactions and Phase Changes in Supersonic Plow, organized by Professor P. P. Wegener, Yale University; Reciprocating Engine Combustion Research, organized by Professor E. S. Starkman, University of California) occupied 2 or 3 half-day sessions each. Contributed Papers in many areas of the combustion field were presented in 10 half-day sessions. Comments on nearly every paper are included in the Proceedings.

Gas phase↗

NASA NTRS2016

Experimental Combustion Dynamics Behavior of a Multi-Element Lean Direct Injection (LDI) Gas Turbine Combustor

An experimental investigation of the combustion dynamic characteristics of a research multi-element lean direct injection (LDI) combustor under simulated gas turbine conditions was conducted. The objective was to gain a better understanding of the physical phenomena inside a pressurized flametube combustion chamber under acoustically isolated conditions. A nine-point swirl venturi lean direct injection (SV-LDI) geometry was evaluated at inlet pressures up to 2,413 kPa and non-vitiated air temperatures up to 867 K. The equivalence ratio was varied to obtain adiabatic flame temperatures between 1388 K and 1905 K. Dynamic pressure measurements were taken upstream of the SV-LDI, in the combustion zone and downstream of the exit nozzle. The measurements showed that combustion dynamics were fairly small when the fuel was distributed uniformly and mostly due to fluid dynamics effects. Dynamic pressure fluctuations larger than 40 kPa at low frequencies were measured at 653 K inlet temperature and 1117 kPa inlet pressure when fuel was shifted and the pilot fuel injector equivalence ratio was increased to 0.72.

dynamics↗

NASA NTRSDate not supplied

Development and Testing of Pulse Guns for Combustion Instability Testing

Combustion stability requirements of a liquid propellant rocket engine are most commonly verified by evaluating the oscillatory pressure or vibration characteristics following an artificial disturbance of the combustion in the combustion chamber. Two types of devices are most commonly used for dynamic stability rating – nondirectional bombs and pulse guns. Bombs have historically been used most often, especially for the large engines developed around the Apollo era. However, bombs in recent years have become much more expensive and difficult to procure, and their transportation and handling requirements have become more demanding. Pulse guns, with inherently less expensive materials, and far less restrictive handling and shipping requirements, have become an attractive alternative. The NASA Marshall Space Flight Center has developed a pulse gun for use during future development programs at the center, and as a design reference for interested commercial users. The objective of this paper is to present the different variants of the pulse gun and characterize performance over a range of parameters. The parameters include the breech diameter and corresponding volume, barrel length, amount of gun powder used, the method of containing the gunpowder within the breech, and the pressure rating of the burst disk. In total, 44 tests were conducted with the pulse gun firing into a test chamber pressurized to 2300 psig with gaseous nitrogen. The best experimental results – including the highest and most consistent peak pressure amplitudes recorded by dynamic pressure sensors in the test chamber – were from a configuration consisting of a 0.40” inner-diameter breech, 15-16 grains of gunpowder wrapped in cigarette paper, and a 24,000 psid burst disk. With this configuration, the zero-to-peak overpressures recorded in the test chamber ranged from about 37% to 58% of the 2300 psig mean pressure, which is adequate for typical combustion stability rating. To complement the data analysis, the acoustics of the pressure waves as they propagated through the pulse gun and into the test chamber were modeled. A more comprehensive final report of this pulse gun development program is planned to be available in the near future.

Pulse Gun↗

NASA NTRS2023

High-Pressure, Normal-Gravity Droplet Combustion Experimental Hardware

The High-Pressure, Trans-Critical (HPTC) 1-g Liquid Droplet Combustion Experiments will assess the autoignition and combustion of liquid fuel droplets at elevated temperatures and pressures. These experiments are being conducted at the NASA Glenn Research Center in a manner similar to experiments performed in Glenn’s Zero Gravity Research Facility (ZGF) using the B drop vehicle. The modification to the test capabilities of the ZGF experiments in the new experimental configuration will allow researchers to continue performing normal-gravity liquid droplet combustion experiments without requiring the use of the ZGF test equipment. These normal-gravity experiments will be conducted at lower pressures than in the ZGF because the pressure vessel for this setup is limited to a maximum working pressure of 7.74 atm (99.1 psig) at 366.5 K (200 °F). This experimental configuration will enable development of a similar capability for conducting high-pressure combustion and supercritical oxidation research on the International Space Station. Experiments will be conducted with the capability of altering the ambient pressure, temperature, and gas concentrations, as well as the fuel type for each test. For these experiments, the test vessel operates at pressures up to 7.5 atm (95.5 psig), temperatures up to 1,073 K (1,472 °F) inside the insulated oven, and oxygen concentrations up to 30 percent.

Droplet Combustion↗

NASA NTRSDate not supplied

Analysis of Additively Manufactured Inconel 718 Combustion Behavior in Promoted Oxygen Environments

Promoted combustion testing is a vital tool for engineers to establish the combustion and flammability characteristics of materials (metallic or otherwise) in oxygen enriched environments. Historically, much of the established data for metallic promoted combustion has been with regards to cast and wrought forms. However, with the emergence of additive manufacturing as a preferred method of fabrication, the need exists to evaluate how metals in that form behave. This paper will serve as a review of the work that has been done and an analysis of the nickel-based superalloy Inconel 718, a material popular for aerospace applications such as liquid fueled rocket components and turbine engines. Promoted combustion testing (per the ASTM G124 standard) was conducted on samples of both wrought and selective laser melted fabrication, to provide comparison of flammability response between materials produced by each manufacturing method. Additionally, post-build treatments were applied to test samples to identify any effects on performance provided by hot isostatic pressing, oxygen-getting wrap during HIP, stress relieving, and solutionizing/aging heat treatments. This study will utilize optical and scanning electron microscopy, energy dispersive spectroscopy, x-ray diffraction, and metallography to identify the differences in behavior of additively manufactured and wrought Inconel 718.

Additively Manufactured↗

NASA NTRSDate not supplied

Promoted Combustion Behavior of 316 Stainless Steel and 6061 Aluminum Alloys in Elevated Pressure Nitrox Environments

Promoted combustion testing (outlined in the ASTM G124 “Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen Enriched Atmospheres”) refers to a useful testing method to evaluate how metallic materials will behave when combusted in environments with high oxygen concentrations, elevated pressure, or both. These tests yield data which is useful for engineers and scientists from a variety of industries who need and rely on oxygen systems. Oxygen Compatibility Assessments (OCA’s) are vital for ensuring that materials will be safe for use, and these assessments rely on data from OCA’s or interpolation if a desired pressure/concentration is outside of previously tested bounds. It was identified that these bounds leave out significant areas of data for materials which are tested at high pressures (above 1500 psi) and variable oxygen concentrations (with nitrogen as the diluent gas). For this reason, the authors posited that conducting promoted combustion testing on materials above 1500 psi and in various concentrations of oxygen would be incredibly useful in future analyses for oxygen compatibility with similar environments (such as breathing air) as well as for further understanding of how materials behave at very high pressures (such as 10000 psi). Two materials were selected which are commonly used in industry today - 316 stainless steel and 6061 aluminum – and they were tested and analyzed for the purposes of this study.

oxygen compatibility↗

NASA NTRSDate not supplied

Expanding the Capability of A Legacy Combustion Flametube to Test High Temperature Engine Materials in Relevant Environments

New materials and component designs are needed to advance gas turbine engine technology and provide the performance and efficiency needs for future applications. In order to advance these materials, testing in combustion environments is a critical step prior to engine testing. In this work, we detail the design and the fabrication of a materials test sector in a flametube combustor facility. The facility simulates a combustion environment similar to that experienced by components in gas turbine engines. The flow regime is characterized by a combination of high-temperature, high-velocity, high-heat flux, and high-velocity that components experience in gas turbine engines. Exposure of components in this facility allows for the study of combined environmental effects and the impact on both coating and substrate durability. The test facility may operate across a wide range of pressures from 275-400 psig (1,896-2,758 kPa) and an air flow rate of 5 lb/s (2.27 kg/s). While combustion gas temperature is expected in excess of 3,000°F (1,649°C), 900°F (482°C) cooling air may be supplied to the backside of components or test articles. The flametube combustor was previously used to evaluate fuel injectors and combustion products, and the new test configuration will also allow for materials exposure to complex, engine-like conditions. The interior of the Test Section was additively manufactured from GRCop-84 and cryogenically fit and brazed to a stainless steel 304 housing. The use of a copper liner minimizes welds and with active cooling, is expected to provide better durability over traditional hardware using stainless steel or Inconel with a ceramic liner. The Test Section has two opposing removable windows approximately 230 mm x 80 mm that can accommodate articles up to 85 mm tall. This modular design allows for custom platforms to hold coupons, panels, or airfoil shapes to be tested with minimal re-engineering or fabrication. The bolted joint and sealing remains consistent, so any new testing only needs to work within the existing design footprint. This paper will provide an overview of the facility capabilities, design considerations, as well as thermal and structural analysis of the hardware. Future testing of ceramic matrix composite (CMC) airfoils and advanced environmental barrier coatings (EBCs) will also be discussed.

Combustion↗

NASA NTRS1971

Combustion products generating and metering device

An apparatus for generating combustion products at a predetermined fixed rate, mixing the combustion products with air to achieve a given concentration, and distributing the resultant mixture to an area or device to be tested is described. The apparatus is comprised of blowers, a holder for the combustion product generating materials (which burn at a predictable and controlled rate), a mixing plenum chamber, and a means for distributing the air combustion product mixture.

Wiberg, R. E.↗

NASA NTRS1973

Combustion detector

A device has been developed for generating a rapid response signal upon the radiation-emitting combustion reaction of certain gases in order to provide a means for the detection and identification of such reaction and concurrently discriminate against spurious signals. This combustion might be the first stage of a coal mine explosion process, and thereby this device could provide a warning of the impending explosion in time to initiate quenching action. This device has the capability of distinguishing between the light emitted from a combustion reaction and the light emitted by miners' lamps, electric lamps, welding sparks or other spurious events so that the quenching mechanism is triggered only when an explosion-initiating combustion occurs.

Trimpi, R. L.↗

NASA NTRS1973

Evaluation of magnesium-aluminum eutectic to improve combustion efficiency in low burning rate propellants

A previous investigation indicated that combustion efficiency of low burning-rate propellants could be improved if the aluminum fuel was replaced by aluminum particles coated with a magnesium-aluminum eutectic alloy (ALCAL). The purpose of the present investigation was to evaluate the possibility of improving the combustion efficiency of these propellants by admixing the eutectic with the aluminum rather than coating the aluminum. Tests of three propellants similar in every respect except for the metal fuel were conducted in test motors with 4.54 kg (10 lbm) of propellant. The first propellant used aluminum fuel; the second contained aluminum admixed with magnesium-aluminum eutectic; the third used ALCAL. The test results show the the admixed fuel gave better low burning-rate combustion efficiency than the other two. The test results also showed that the ALCAL was deficient in that much, if not all, of the coating material could be found as the fine particles in a bimodal mix of aluminum and eutectic. The combustion efficiency of low burning-rate aluminized propellants can be significantly improved by mixing a small amount of magnesium-aluminum alloy with the aluminum fuel.

Northam, B. G.↗

NASA NTRS1973

A new look at AP/composite propellant combustion

Some theoretical studies on the time-independent and oscillatory combustion of nonmetallized ammonium perchlorate (AP)/composite propellants are presented. A coherent and unified interpretation was made of the voluminous data available from experiments related to propellant combustion. Three fundamental hypotheses are introduced: the extent of propellant degradation at the vaporization step has to be specified through a scientific criterion; the condensed-phase degradation reaction of ammonium perchlorate to a vaporizable state is the overall rate-limiting step; gas-phase combustion rate is controlled by the mixing rate of fuel and oxidizer vapors. In the treatment of oscillatory combustion, the assumption of quasi-steady fluctuations in the gas phase is used to supplement these hypotheses.

Kumar, R. N.↗

NASA NTRS1974

High pressure combustion of liquid fuels

Measurements were made of the burning rates and liquid surface temperatures for a number of alcohol and n-paraffin fuels under natural and forced convection conditions. Porous spheres ranging in size from 0.64-1.9 cm O.D. were emloyed to simulate the fuel droplets. The natural convection cold gas tests considered the combustion in air of methanol, ethanol, propanol-1, n-pentane, n-heptane, and n-decane droplets at pressures up to 78 atmospheres. The pressure levels of the natural convection tests were high enough so that near critical combustion was observed for methanol and ethanol vaporization rates and liquid surface temperature measurements were made of droplets burning in a simulated combustion chamber environment. Ambient oxygen molar concentrations included 13%, 9.5% and pure evaporation. Fuels used in the forced convection atmospheric tests included those listed above for the natural convection tests. The ambient gas temperature ranged from 600 to 1500 K and the Reynolds number varied from 30 to 300. The high pressure forced convection tests employed ethanol and n-heptane as fuels over a pressure range of one to 40 atmospheres. The ambient gas temperature was 1145 K for the two combustion cases and 1255 K for the evaporation case.

Canada, G. S.↗

NASA NTRS1974

Analysis of combustion instability in liquid propellant engines with or without acoustic cavities

Analytical studies have been made of the relative combustion stability of various propellant combinations when used with hardware configurations representative of current design practices and with or without acoustic cavities. Two combustion instability models, a Priem-type model and a modification of the Northern Research and Engineering (NREC) instability model, were used to predict the variation in engine stability with changes in operating conditions, hardware characteristics or propellant combination, exclusive of acoustic cavity effects. The NREC model was developed for turbojet engines but is applicable to liquid propellant engines. A steady-state combustion model was used to predict the needed input for the instability models. In addition, preliminary development was completed on a new model to predict the influence of an acoustic cavity with specific allowance for the effects the nozzle, steady flow and combustion.

Oberg, C. L.↗

NASA NTRS1974

Liquid rocket combustion computer model with distributed energy release. DER computer program documentation and user's guide, volume 1

A computer program for analyzing rocket engine performance was developed. The program is concerned with the formation, distribution, flow, and combustion of liquid sprays and combustion product gases in conventional rocket combustion chambers. The capabilities of the program to determine the combustion characteristics of the rocket engine are described. Sample data code sheets show the correct sequence and formats for variable values and include notes concerning options to bypass the input of certain data. A seperate list defines the variables and indicates their required dimensions.

Combs, L. P.↗

NASA NTRS1973

Condensed phase details in the time-independent combustion of AP/composite propellants

The problem of nonmetallized ammonium perchlorate (AP)/composite propellant combustion is studied with the aim of coherently interpreting apparently diverse experimental data. Three fundamental hypotheses are introduced: the extent of propellant degradation at the vaporization step has to be specified through a scientific criterion; condensed phase degradation of AP to vaporizable fragments is the overall rate-limiting reaction; the rate of combustion in the gas phase is controlled by diffusive-mixing processes. Theoretical predictions of the regression rates of AP are seen to match well with experimental observations. Theoretical curves of regression rate are presented for a typical composite propellant. It is seen through analyses that either of the two familiar models for the gas phase (flame sheet approximation and uniform combustion) describes the general behavior adequately, hence de-emphasizing the role of gas phase details in propellant combustion.

Kumar, R. N.↗

NASA NTRS1973

Influence of mechanical properties on the combustion of propellants

Experimental study of the effects of minor compositional variables upon the combustion behavior of composite solid propellants. More specifically, it was attempted to determine the influence of ingredients that improve the mechanical properties upon the oscillatory combustion characteristics. Tests were carried out in the familiar Crawford bomb, a low-pressure L-star burner, and a high-pressure T-burner. Two families of propellants were investigated; each family consists of two propellants with a minor compositional variation between them. In the family that shows a decreasing (steady state) pressure index (n) with increasing pressures, all of the combustion characteristics are found to be very similar although the mechanical properties are widely different. In the other family, which shows an increasing n with increasing pressures, unmistakable differences are found between the two propellants in the low-pressure L-star instability behavior (along with the differences in the mechanical properties), while the other combustion characteristics are almost identical. The results are interpreted to be consistent with a theory that highlights the importance of condensed phase heat-transfer effects.

Kumar, R. N.↗

NASA NTRS1975

Combustion problems of nitramine propellants

This study has, as its distinctive feature, a detailed examination of the condensed-phase processes in the combustion of nitramine propellants. As a consequence of a recently developed model for the combustion of ammonium perchlorate (AP)/composite propellants, it is hypothesized that the condensed-phase degradation of the nitramine oxidizer particles to a vaporizable state is the overall rate-limiting step. It is also assumed that the gas-phase details are secondary in importance and need be studied only to the extent of supplying the correct boundary conditions on the condensed-phase/vapor-phase heat transfer. Because of imprecise understanding of the gas-phase processes in the presence of combustion, several plausible models are considered for the gas phase. It is found that all of the gas-phase models considered lead to predictions sufficiently close to experimental trends to conclude that the precise details of gas-phase processes are not of critical importance in determining propellant combustion behavior.

Kumar, R. N.↗

NASA NTRS1976

Preliminary results from screening tests of commercial catalysts with potential use in gas turbine combustors. Part 2: Combustion test rig evaluation

Several commercial monolithic catalysts were tested in a combustion test rig to determine their suitability for use in a gas turbine combuster primary zone. The catalyst test bed consisted of two to four elements of 12-centimeter diameter by 2.5-centimeter long monolith. Results are presented of the measured combustion efficiency and catalyst bed temperature history for an inlet propane-air mixture temperature of 800 K, a pressure of 300,000 newtons per square meter, inlet velocities of 10 to 25 meters per second and equivalence ratios of 0.1 to 0.3. The best catalysts tested gave combustion efficiencies of virtually 100 percent for reaction temperatures ranging from 1,325 K at 10 meters per second to 1,400 K at 25 meters per second. This performance was only possible with fresh catalysts. The catalysts tested were not specifically developed for use at these conditions and showed some loss in activity after about 3 hours' testing.

Anderson, D. N.↗