Search NASA⌕ Search

SEARCH · Search NASA

Results for “DELTA WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Analysis of the Flow About Delta Wings with Leading Edge Separation at Supersonic Speeds

A research program was conducted to develop an improved theoretical flow model for the flow about sharp edge delta wings with leading-edge separation at supersonic speeds. The flow model incorporates a representation of the secondary separation region which occurs just inboard of the leading edge on such wings and is based on a slender-wing theory whereby the full three-dimensional problem is reduced to a quasi two-dimensional problem in the cross-flow plane. The secondary separation region was modeled by a surface distribution of singularities or a linearized type of cavity representation. The primary vortex and separation were modeled by a concentrated vortex and cut in the cross-flow potential which represents its feeding sheet. The cross-flow solutions for the cavity model were obtained, but these solutions have physical significance only in a very restricted range of angle of attack. The reasons for the failure of the flow model are discussed. The analysis is presented so that other interested researchers may critically review the work.

Nenni, J. P.↗

The lift of sharp-leading-edged delta wings with blowing

An analysis of the lift augmentation due to a thin jet of air issuing from a slot along the leading edge of a delta wing is presented. The problem is treated with an extension of the method of Brown and Michael, representing the separated flow on the lee side of the wing by a pair of concentrated vortices and corresponding feeding sheets. It is assumed that the jet is not affected by Coanda forces. The analysis produces qualitative agreement with experiments.

Tavella, D. A.↗

Breaking down the delta wing vortex: The role of vorticity in the breakdown process

Experimental x-wire measurements of the flowfield above a 70 and 75 deg flat plate delta wing were performed at a Reynolds number of 250,000. Grids were taken normal to the wing at various chordwise locations for angles of attack of 20 and 30 deg. Axial and azimuthal vorticity distributions were derived from the velocity fields. The dependence of circulation on distance from the vortex core and on chordwise location was also examined. The effects of nondimensionalization in comparison with other experimental data is made. The results indicate that the circulation distribution scales with the local semispan and grows in a nearly linear fashion in the chordwise direction. The spanwise distribution of axial vorticity is severely altered through the breakdown. The axial vorticity components with a negative sense, such as that found in the secondary vortex, seem to remain unaffected by changes in wind sweep or angle of attack, in direct contrast to the positive components. In addition, the inclusion of the local wing geometry into a previously derived correlation parameter allows the circulation of growing leading edge vortex flows to be reduced into a single curve.

Nelson, Robert C.↗

Low-speed aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept delta wing

An experimental investigation of the low-speed static longitudinal, lateral and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept delta wing was conducted in a low-speed tunnel with a 12-foot (3.66 meter) octagonal test section. Aircraft component variations included: (1) fuselage shape modifications, (2) tip fins, (3) center vertical fin, (4) wing camber, and (5) wing planform. This investigation was conducted at a dynamic pressure of 262.4 Pa (5.48 psf), a Mach number of 0.06, and a Reynolds number of 2.24 million, based on body length. Tests were conducted through an angle-of-attack range of 0 deg to 30 deg with elevon deflections from +5.0 deg to minus 30.0 deg. The complete configuration exhibited positive static longitudinal, lateral and directional stability up to angles of attack of at least 20 deg and was trimmable to lift coefficients of at least 0.70 with elevon deflections of minus 30 deg.

Creel, T. R., Jr.↗

Numerical prediction of vortex cores of the leading and trailing edges of delta wings

The purpose of the present paper is to predict the roll-up of the vortex sheets emanating from the leading- and trailing-edges of delta wings with emphasis on the interaction of vortex cores beyond the trailing edge. The motivation behind the present work is the recent experimental data published by Hummel. The Nonlinear Discrete-Vortex method (NDV-method) is modified and extended to predict the leading- and trailing-vortex cores beyond the trailing edge. The present model alleviates the problems previously encountered in predicting satisfactory pressure distributions. This is accomplished by lumping the free-vortex lines during the iteration procedure. The leading- and trailing-edge cores and their feeding sheets are obtained as parts of the solution. The numerical results show that the NDV-method is successful in confirming the formation of a trailing-edge core with opposite circulation and opposite roll-up to those of the leading-edge core. This work is a breakthrough in the high angle of attack aerodynamics and moreover, it is the first numerical prediction done on this problem

Kandil, O. A.↗

An experimental study of pressures on 60 deg Delta wings with leading edge vortex flaps

An experimental study was conducted in the Virginia Tech Stability Wind Tunnel to determine surface pressures over a 60 deg sweep delta wing with three vortex flap designs. Extensive pressure data was collected to provide a base data set for comparison with computational design codes and to allow a better understanding of the flow over vortex flaps. The results indicated that vortex flaps can be designed which will contain the leading edge vortex with no spillage onto the wing upper surface. However, the tests also showed that flaps designed without accounting for flap thickness will not be optimum and the result can be oversized flaps, early flap vortex reattachment and a second separation and vortex at the wing/flap hinge line.

Marchman, J. F., III↗

DSMC calculations for the delta wing

Results are reported from three-dimensional direct simulation Monte Carlo (DSMC) computations, using a variable-hard-sphere molecular model, of hypersonic flow on a delta wing. The body-fitted grid is made up of deformed hexahedral cells divided into six tetrahedral subcells with well defined triangular faces; the simulation is carried out for 9000 time steps using 150,000 molecules. The uniform freestream conditions include M = 20.2, T = 13.32 K, rho = 0.00001729 kg/cu m, and T(wall) = 620 K, corresponding to lambda = 0.00153 m and Re = 14,000. The results are presented in graphs and briefly discussed. It is found that, as the flow expands supersonically around the leading edge, an attached leeside flow develops around the wing, and the near-surface density distribution has a maximum downstream from the stagnation point. Coefficients calculated include C(H) = 0.067, C(DP) = 0.178, C(DF) = 0.110, C(L) = 0.714, and C(D) = 1.089. The calculations required 56 h of CPU time on the NASA Langley Voyager CRAY-2 supercomputer.

Celenligil, M. Cevdet↗

Computational study of the aerodynamics and control by blowing of asymmetric vortical flows over delta wings

Some of the work is described which was done in a study of the flow field produced by tangential leading edge blowing on a 60 deg. delta wing. The flow is studied computationally by solving the Thin Layer Navier-Stokes equations. Steady state flow fields are calculated for various angles of attack and yaw, with and without the presence of tangential leading edge blowing. The effectiveness of blowing as a rolling moment control mechanism to extend the envelope of controllability is illustrated at pre- and post-stall angles of attack. The numerical grid is generated using algebraic grid generation and various interpolation and blending techniques. The jet emanates from a slot with linearly varying thickness and is introduced into the flow field using the concept of an actuator plane, thereby not requiring resolution of the jet slot geometry. The Baldwin-Lomax algebraic turbulence model is used to provide turbulent closure. The computational results are compared with those of experiments.

Craig, Ken↗

Breaking down the delta wing vortex: The role of vorticity in the breakdown process

Experimental x-wire measurements of the flowfield above a 70 degree and 75 degree flat plate delta wing were performed at a Reynolds number of 250,000. Grids were taken normal to the wing at various chordwise locations for angles of attack of 20 degrees and 30 degrees. Axial and azimuthal vorticity distributions were derived from the velocity fields. The dependence of circulation on distance from the vortex core and on chordwise location was also examined. The effects of nondimensionalization in comparison with other experimental data is made. The results indicate that the circulation distribution scales with the local semispan and grows in a nearly linear fashion in the chordwise direction. The spanwise distribution of axial vorticity is severely altered through the breakdown region and the amount of vorticity present appears to reach a maximum immediately preceding breakdown. The axial velocity components with a negative sense, such as that found in the secondary vortex, seem to remain unaffected by changes in wing sweep or angle of attack, in direct contrast to the visible components. In addition, the inclusion of the local wing geometry into a previously derived correlation parameter allows the circulation of growing leading edge vortex flows to be reduced to a single curve.

Nelson, R. C.↗

Adaptive computations of flow around a delta wing with vortex breakdown

An adaptive unstructured mesh solution method for the three-dimensional Euler equations was used to simulate the flow around a sharp edged delta wing. Emphasis was on the breakdown of the leading edge vortex at high angle of attack. Large values of entropy, which indicate vortical regions of the flow, specified the region in which adaptation was performed. The aerodynamic normal force coefficients show excellent agreement with wind tunnel data measured by Jarrah, and demonstrate the importance of adaptation in obtaining an accurate solution. The pitching moment coefficient and the location of vortex breakdown are compared with experimental data measured by Hummel and Srinivasan, showing good agreement in cases in which vortex breakdown is located over the wing.

Modiano, David L.↗

Lift augmentation on a delta wing via leading edge fences and the Gurney flap

Wind tunnel tests were conducted on two devices for the purpose of lift augmentation on a 60 deg delta wing at low speed. Lift, drag, pitching moment, and surface pressures were measured. Detailed flow visualization was also obtained. Both the leading edge fence and the Gurney flap are shown to increase lift. The fences and flap shift the lift curve as much as 5 deg and 10 deg, respectively. The fences aid in trapping vortices on the upper surface, thereby increasing suction. The Gurney flap improves circulation at the trailing edge. The individual influences of both devices are roughly additive, creating high lift gain. However, the lower lift to drag ratio and the precipitation of vortex burst caused by the fences, and the nose down pitching moment created by the flap are also significant factors.

Buchholz, Mark D.↗

Navier-Stokes prediction of large-amplitude forced and free-to-roll delta-wing oscillations

The three-dimensional Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate nonsteady vortical flow about a 65 degree sweep delta wing at 30 degrees angle of attack. Two large-amplitude, high-rate, forced-roll motions and a damped free-to-roll motion are presented. The free-to-roll motion is computed by coupling the time-dependent RANS equations to the flight dynamic equation of motion. The computed results are compared with experimental forces, moments, and roll-angle time histories. The overall agreement is good. Vortex breakdown is present in each case, which causes significant time lags in the vortex breakdown motions relative to the body motions. This behavior strongly influences the dynamic forces and moments.

Chaderjian, Neal M.↗

Numerical Simulation of Forced and Free-to-Roll Delta-Wing Motions

The three-dimensional, Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate nonsteady vortical flow about a 65-deg sweep delta wing at 30-deg angle of attack. Two large-amplitude, high-rate, forced-roll motions, and a damped free-to-roll motion are presented. The free-to-roll motion is computed by coupling the time-dependent RANS equations to the flight dynamic equation of motion. The computed results are in good agreement with the forces, moments, and roll-angle time histories. Vortex breakdown is present in each case. Significant time lags in the vortex breakdown motions relative to the body motions strongly influence the dynamic forces and moments.

Chaderjian, Neal M.↗

Stability and control characteristics of a monoplane missile with large delta wings and various tail controls at Mach 1.90 to 2.86

Wind tunnel tests were conducted to determine the stability and control characteristics of a monoplane missile with large delta wings and various tail configurations. The tests were conducted at angles of attack of approximately 24 degrees and angles of sideslip of about 22 degrees. Tail control configurations were the cruciform, conventional airplane type, and an inverted airplane configuration. Control effectiveness was measured for pitch, yaw, and roll.

Jernell, L. S.↗

A streamwise upwind algorithm applied to vortical flow over a delta wing

Improvements were made to a streamwise upwind algorithm so that it can be used for calculating flows with vortices. A calculation is shown of flow over a delta wing at an angle of attack. The laminar, thin layer, Navier-Stokes equations are used for the calculation. The results are compared with another upwind method, a central differencing method, and experimental data. The present method shows improvements in accuracy and convergence properties.

Goorjian, Peter M.↗

Navier-Stokes solutions for an oscillating double-delta wing

An upwind-biased implicit scheme is used to investigate steady-state and unsteady Navier-Stokes solutions of the vortical flow over a double-delta wing configuration. The governing equations are solved numerically with a fully upwind, implicit, iterative, and factorized numerical scheme. Steady-state solutions for fixed angles of attack and unsteady solutions for a sinusoidal oscillatory motion are obtained. The steady-state solutions on the baseline grid are in agreement with the experiment, and grid refinements show some improvements of the predictions. The higher-order accuracy of the present scheme yields equivalent solutions on smaller grid densities compared to solutions obtained with a second-order accurate method on larger grids. As the angle of attack increases, the grid resolution requirements for adequate resolution of the leeward-side vortical flowfield become very severe. The unsteady solutions are in general agreement with the measurements and show a qualitative correlation with the experiment.

Ekaterinaris, John A.↗

Lift Augmentation on a Delta Wing via Leading Edge Fences and the Gurney Flap

Wind tunnel tests have been conducted on two devices for the purpose of lift augmentation on a 60 deg delta wing at low speed. Lift, drag, pitching moment, and surface pressures were measured. Detailed flow visualization was also obtained. Both the leading edge fence and the Gurney flap are shown to increase lift. The fences and flap shift the lift curve by as much as 5 deg and 10 deg, respectively. The fences aid in trapping vortices on the upper surface, thereby increasing suction. The Gurney flap improves circulation at the trailing edge. The individual influences of both devices are roughly additive, creating high lift gain. However, the lower lift to drag ratio and the precipitation of vortex burst caused by the fences, and the nose down pitching moment created by the flap are also significant factors.

Buchholz, Mark D.↗

Pressure-Sensitive Paint Investigation of Double-Delta Wing Vortex Flow Manipulation

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to quantify the effect of wing fillets on the global vortex-induced surface static pressure field about a sharp leading-edge 76o/40o double delta wing, or strake-wing, model at subsonic and transonic speeds. Global calibrations of the PSP were obtained at M = 0.50, 0.70, 0.85, 0.95, and 1.20, a Reynolds number per unit length of 2.0 million, and angles of attack from 10 degrees to 20 degrees using an in-situ method featuring the simultaneous acquisition of electronically-scanned pressures (ESP) at discrete locations on the model. The mean error in the PSP measurements relative to the ESP data was approximately 2 percent or less at M = 0.50 to 0.85 but increased to several percent at M =0.95 and 1.20. The PSP pressure distributions and pseudo-colored planform view pressure maps clearly revealed the vortex-induced pressure signatures at all Mach numbers and angles of attack. Small fillets having a parabolic or diamond planform situated at the strake-wing intersection were designed to manipulate the vortical flows by, respectively, removing the leading-edge discontinuity or introducing additional discontinuities. The fillets caused global changes in the vortex-dominated surface pressure field that were effectively captured in the PSP measurements. The vortex surface pressure signatures were compared to available off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The fillet effects on the PSP pressure distributions and the observed leading-edge vortex flow characteristics were consistent with the trends in the measured lift, drag, and pitching moment coefficients.

Erickson, Gary E.↗