Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Design of a multivariable flutter control/gust load alleviation system

This paper discusses the use of eigenspace techniques for the design of an active flutter control/gust load alleviation system for a hypothetical research drone. One leading edge and two trailing edge aerodynamic surfaces are available for control. Full state control laws are designed for two combinations of control surfaces by selecting feedback gains which place closed loop eigenvalues and shape closed loop eigenvectors so as to stabilize wing flutter and reduce gust loads at the wing root while yielding acceptable robustness and satisfying constraints on rms control surface activity. These controllers are realized by state estimators designed using an eigenvalue placement/eigenvector shaping technique which results in recovery of the loop transfer characteristics of the full state feedback systems. The resulting feedback compensators are shown to perform almost as well as the full state designs. They also exhibit acceptable performance in situations in which the failure of an actuator is simulated.

Liebst, B. S.↗
NASA NTRS1990

Design of aircraft wings subjected to gust loads - A system reliability approach

A method for system reliability-based design of aircraft wing structures is presented. A wing of a light commuter aircraft designed for gust loads according to the FAA regulations is compared with one designed by system reliability optimization. It is shown that system reliability optimization has the potential of improving dramatically the safety and efficiency of new designs. The reasons for the differences between the deterministic and reliability-based designs are explained.

Yang, J. S.↗
NASA NTRS1994

Structural Qualifications of SIR-C Antenna Core Structure

A 2-bay SIR-C Antenna Core Structure(ACS) has been utilized to verify the strength of the SIR-C structural design. Five loading configurations were applied to assure that many SIR-C ACS members were loaded up to more than 1.25 times the predicted flight limit loads.

antenna↗
NASA NTRS2024

Loads and Structural Dynamics Requirements for Spaceflight Hardware

The NASA Exploration Systems Development Mission Directorate requires Crewed Space Systems (CSS) to meet the intent of a set of Engineering Technical Authority (TA) documents called out in HEOMD-003, Crewed Deep Space Systems Human Rating Certification Requirements and Standards for NASA Missions. For the Loads and Dynamics technical discipline, the document invoked by the HEOMD-003 is JSC 65829, Loads and Structural Dynamics Requirements for Spaceflight Hardware. JSC 65829 was originally developed for the NASA Commercial Crew Program as an implementation of NASA STD-5002, Load Analyses of Spacecraft and Payloads, for that Program. Since that time, tailored alternatives to JSC 65829 have been produced for the Gateway, Human Landing System, and Extravehicular Activity and Human Surface Mobility Programs. Experience with those Programs has shown that the reduced set of less-prescriptive requirements in those tailored documents offers an advantage over the set of requirements in JSC 65829 Rev A and is a better fit for the paradigm of NASA procurement of commercially developed systems for crewed spaceflight. Revision B of JSC 65829 has been constructed to align with those tailored documents. The reduction in the number and specificity of requirements is balanced by a new requirement for hardware developers to create and provide a Loads Control Plan which describes how the approaches used to generate design-to loads and dynamic environments and substantiate dynamic model validity satisfy the requirements herein. The Plan will establish an agreement between the hardware developer and the TA for the loads and dynamics discipline and offer an opportunity for reengagement if the Plan changes during development.

Kenneth Schultz↗
NASA NTRS1979

Design considerations for attaining 200-knot test velocities at the aircraft landing loads and traction facility

Design studies are presented which consider the important parameters in providing 200 knot test velocities at the landing loads and traction facility. Two major components of this facility, the hydraulic jet catapult and the test carriage structure, are considered. Suitable factors are determined to correlate analytical data for characteristics of the hydraulic jet catapult with data measured from the existing catapult system. The resulting equations are used to calculate test velocities for a range of jet nozzle diameters and carriage masses with both the current 122 m and an increased 183 m catapult stroke. Using the catapult characteristics, a target design point is selected and a carriage structure is sized to meet the target point strength requirements.

Giles, G. L.↗
NASA NTRS2008

Limits to Open Class Performance?

This presentation discusses open or unlimited class aircraft performance limitations and design solutions. Limitations in this class of aircraft include slow climbing flight which requires low wing loading, high cruise speed which requires high wing loading, gains in induced or viscous drag alone which result in only half the gain overall and other structural problems (yaw inertia and spins, flutter and static loads integrity). Design solutions include introducing minimum induced drag for a given span (elliptical span load or winglets) and introducing minimum induced drag for a bell shaped span load. It is concluded that open class performance limits (under current rules and technologies) is very close to absolute limits, though some gains remain to be made from unexplored areas and new technologies.

Bowers, Albion H.↗
NASA NTRS1977

Design of a Large Span-Distributed Load Flying-Wing Cargo Airplane

The design and operation of very large, long-range, subsonic cargo aircraft are considered. A design concept which distributes the payload along the wingspan to counterbalance the aerodynamic loads, with a resultant decrease in the in-flight wing bending moments and shear forces, is described. The decreased loading of the wing structure, coupled with the very thick wing housing the cargo, results in a relatively low overall structural weight in comparison to that of conventional aircraft.

Jernell, L. S.↗
NASA NTRS1972

Dynamic analysis of Apollo-Salyut/Soyuz docking

The use of a docking-system computer program in analyzing the dynamic environment produced by two impacting spacecraft and the attitude control systems is discussed. Performance studies were conducted to determine the mechanism load and capture sensitivity to parametric changes in the initial impact conditions. As indicated by the studies, capture latching is most sensitive to vehicle angular-alinement errors and is least sensitive to lateral-miss error. As proved by load-sensitivity studies, peak loads acting on the Apollo spacecraft are considerably lower than the Apollo design-limit loads.

Schliesing, J. A.↗
NASA NTRS1988

Solar water heater for NASA's Space Station

The feasibility of using a solar water heater for NASA's Space Station is investigated using computer codes developed to model the Space Station configuration, orbit, and heating systems. Numerous orbit variations, system options, and geometries for the collector were analyzed. Results show that a solar water heater, which would provide 100 percent of the design heating load and would not impose a significant impact on the Space Station overall design is feasible. A heat pipe or pumped fluid radial plate collector of about 10-sq m, placed on top of the habitat module was found to be well suited for satisfying water demand of the Space Station. Due to the relatively small area required by a radial plate, a concentrator is unnecessary. The system would use only 7 to 10 percent as much electricity as an electric water-heating system.

Somers, Richard E.↗
NASA NTRS1990

Apparatus for measurement of thermal conductivity of insulation systems subjected to extreme temperature differences

Advanced aerospace designs require thermal insulation systems which are consistent with cryogenic fluids, high thermal loads, and design restrictions such as weight and volume. To evaluate the thermal performance of these insulating systems, an apparatus capable of measuring thermal conductivity using extreme temperature differences (27 to 1100 K) is being developed. This system is described along with estimates of precision and accuracy in selected operating conditions. Preliminary data are presented.

Dube, W. P.↗
NASA NTRS1994

Use of photostress to analyze behavior of an aft skirt test specimen

Strains at twenty-one selected points in the critical lower weld region of a aft skirt of a solid rocket booster of the shuttle were measured using photoelastic coatings and stress separator gages. Data were taken at loads of 5, 14, 20, 28, 42, 56, and 70 percent of the design limit load. Results indicate that general yielding occurred in the weld metal and for a short distance outside the fusion boundaries on either side of the weld metal. The fusion boundaries did not yield at the 70 percent load. Slight non-linearity in the load strain curves were observed at several points above the 20 percent load level. Maximum measured strains occurred at points in the forged metal of the holddown post along a line 0.50 inches from the centerline of the weld. Maximum shearing strains within the area covered by the photoelastic coating occurred at points approximately 0.33 inches to the right of the weld centerline near points 6 and 7 and lying along a yellow vertical line extending from just below point 6 to point 11. Photoelastic coatings were shown to be an excellent method to provide the whole field strain distribution in the region of the critical weld and to enhance the overall understanding of the behavior of the welded joint.

Gambrell, S. C., Jr.↗
NASA NTRS2006

Flight Test of an Adaptive Controller and Simulated Failure/Damage on the NASA NF-15B

The method of flight-testing the Intelligent Flight Control System (IFCS) Second Generation (Gen-2) project on the NASA NF-15B is herein described. The Gen-2 project objective includes flight-testing a dynamic inversion controller augmented by a direct adaptive neural network to demonstrate performance improvements in the presence of simulated failure/damage. The Gen-2 objectives as implemented on the NASA NF-15B created challenges for software design, structural loading limitations, and flight test operations. Simulated failure/damage is introduced by modifying control surface commands, therefore requiring structural loads measurements. Flight-testing began with the validation of a structural loads model. Flight-testing of the Gen-2 controller continued, using test maneuvers designed in a sequenced approach. Success would clear the new controller with respect to dynamic response, simulated failure/damage, and with adaptation on and off. A handling qualities evaluation was conducted on the capability of the Gen-2 controller to restore aircraft response in the presence of a simulated failure/damage. Control room monitoring of loads sensors, flight dynamics, and controller adaptation, in addition to postflight data comparison to the simulation, ensured a safe methodology of buildup testing. Flight-testing continued without major incident to accomplish the project objectives, successfully uncovering strengths and weaknesses of the Gen-2 control approach in flight.

Buschbacher, Mark↗
NASA NTRS1980

Preliminary study of ground handling characteristics of Buoyant Quad Rotor (BQR) vehicles

A preliminary investigation of mooring concepts appropriate for heavy lift buoyant quad rotor (BQR) vehicles was performed. A review of the evolution of ground handling systems and procedures for all airship types is presented to ensure that appropriate consideration is given to past experiences. Two buoyant quad rotor designs are identified and described. An analysis of wind loads on a moored airship and the effects of these loads on vehicle design is provided. Four mooring concepts are assessed with respect to the airship design, wind loads and mooring site considerations. Basing requirements and applicability of expeditionary mooring at various operational scenarios are addressed.

Browning, R. G. E.↗
NASA NTRSDate not supplied

Undue Conservatisim in Structural Designs

Assuming that dynamic (transient/vibratory) loads are static in the design of structures is a long-standing engineering practice. The assumption is conservative for hardware that will have limited exposure to the specified dynamic environment and fatigue is not a concern. This is the case for most space flight hardware. Once out of the Earth’s atmosphere, significant vibrations are non-existent for most hardware and vibration cycles are limited. Mass is, and has always been, a concern with respect to flight hardware design. How much unnecessary mass due to the subject assumption may be in structural designs was questioned and numerous tests have been performed to qualitatively address that. Tests have been performed on simple aluminum beams, beams with bolted joints and beams with welded joints. Results of those tests are reported in this paper. The objective of these efforts was to demonstrate the order of magnitude of conservatism associated with this engineering process via comparing static to dynamic tests and the longer term endgame is to develop a new or modified quick turnaround structural design process that circumvents assuming dynamic loads are static and results in lighter structural designs. Test results qualitatively demonstrate notable conservatism. Activities to devise the new method are underway.

conservative loads↗
NASA NTRS1973

Computer design of antenna reflectors.

Performance of paraboloidal antenna reflectors is adversely influenced by surface distortions from a perfect paraboloid, which cause pathlength variations of the RF energy beam. The structural design objective for the surface backup structure is to minimize the rms pathlength deviations for gravity loading. Two design approaches are illustrated and applied to sample antenna structure designs. These are a sectional search method and a virtual work/Lagrange multiplier method. Both are shown to provide useful performance improvements. The second, however, appears to be more suited for application to design of large antenna structures.

Levy, R.↗
NASA NTRS1974

Titanium honeycomb acoustic lining structural and thermal test report

The results are presented of static, fatigue and thermal testing of titanium honeycomb acoustic panels representing the acoustic tailpipe for the Pratt and Whitney Aircraft JT8D Refan engine which is being studied for use on the Boeing 727-200 airplane. Test specimens represented the engine and tailpipe flange joints, the rail to which the thrust reverser is attached and shear specimens of the tailpipe honeycomb. Specimens were made in four different batches with variations in configuration, materials and processes in each. Static strength of all test specimens exceeded the design ultimate load requirements. Fatigue test results confirmed that aluminum brazed titanium, as used in the Refan tailpipe design, meets the fatigue durability objectives. Quality of welding was found to be critical to life, with substandard welding failing prematurely, whereas welding within the process specification exceeded the panel skin life. Initial fatigue testing used short grip length bolts which failed prematurely. These were replaced with longer bolts and subsequent testing demonstrated the required life. Thermal tests indicate that perforated skin acoustic honeycomb has approximately twice the heat transfer of solid skin honeycomb.

Joynes, D.↗
NASA NTRS1995

Inflatable structures for a lunar base

The first step in the human expansion into space consists of the construction of a human-tended base on the Moon. Establishment of a lunar base depends upon the development of a structure capable of accomodating human life and activities in a shirt sleeve environment. Design and construction of a structure on the Moon require addressing a host of issues and loads that are not encountered on Earth. A lunar structure is essentially a pressure vessel since the internal pressure is the dominating load. The external pressure is effectively an absolute vacuum and the dead loads from both the material mass and a protective regolith layer are quite small due to low lunar gravity. An inflatable structure made of a thin membrane integrated with an inflated supporting frame is highly efficient in resisting the internal pressure loading and the dead loads. Preliminary design computations for a generic lunar inflatable structure are presented.

Sadeh, Willy Z.↗
NASA NTRS1987

The design and analysis of single flank transmission error tester for loaded gears

To strengthen the understanding of gear transmission error and to verify mathematical models which predict them, a test stand that will measure the transmission error of gear pairs under design loads has been investigated. While most transmission error testers have been used to test gear pairs under unloaded conditions, the goal of this report was to design and perform dynamic analysis of a unique tester with the capability of measuring the transmission error of gears under load. This test stand will have the capability to continuously load a gear pair at torques up to 16,000 in-lb at shaft speeds from 0 to 5 rpm. Error measurement will be accomplished with high resolution optical encoders and the accompanying signal processing unit from an existing unloaded transmission error tester. Input power to the test gear box will be supplied by a dc torque motor while the load will be applied with a similar torque motor. A dual input, dual output control system will regulate the speed and torque of the system. This control system's accuracy and dynamic response were analyzed and it was determined that proportional plus derivative speed control is needed in order to provide the precisely constant torque necessary for error-free measurement.

Bassett, Duane E.↗