SEARCH · Search NASA

Results for “Detection approach”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Lunar Science from Lunar Laser Ranging

Variations in rotation and orientation of the Moon are sensitive to solid-body tidal dissipation, dissipation due to relative motion at the fluid-core/solid-mantle boundary, tidal Love number k2, and moment of inertia differences. There is weaker sensitivity to flattening of the core/mantle boundary (CMB) and fluid core moment of inertia. Accurate Lunar Laser Ranging (LLR) measurements of the distance from observatories on the Earth to four retroreflector arrays on the Moon are sensitive to variations in lunar rotation, orientation and tidal displacements. Past solutions using the LLR data have given results for Love numbers plus dissipation due to solid-body tides and fluid core. Detection of the fluid core polar minus equatorial moment of inertia difference due to CMB flattening is weakly significant. This strengthens the case for a fluid lunar core. Future approaches are considered to detect a solid inner core.

Love numbers↗

NASA NTRS2002

Gyro-based Maximum-Likelihood Thruster Fault Detection and Identification

When building smaller, less expensive spacecraft, there is a need for intelligent fault tolerance vs. increased hardware redundancy. If fault tolerance can be achieved using existing navigation sensors, cost and vehicle complexity can be reduced. A maximum likelihood-based approach to thruster fault detection and identification (FDI) for spacecraft is developed here and applied in simulation to the X-38 space vehicle. The system uses only gyro signals to detect and identify hard, abrupt, single and multiple jet on- and off-failures. Faults are detected within one second and identified within one to five accords,

Wilson, Edward↗

NASA NTRS1992

Algorithms for airborne Doppler radar wind shear detection

Honeywell has developed algorithms for the detection of wind shear/microburst using airborne Doppler radar. The Honeywell algorithms use three dimensional pattern recognition techniques and the selection of an associated scanning pattern forward of the aircraft. This 'volumetric scan' approach acquires reflectivity, velocity, and spectral width from a three dimensional volume as opposed to the conventional use of a two dimensional azimuthal slice of data at a fixed elevation. The algorithm approach is based on detection and classification of velocity patterns which are indicative of microburst phenomenon while minimizing the false alarms due to ground clutter return. Simulation studies of microburst phenomenon and x-band radar interaction with the microburst have been performed and results of that study are presented. Algorithm performance indetection of both 'wet' and 'dry' microbursts is presented.

Gillberg, Jeff↗

NASA NTRS2019

Implementation Recommendations and Usage Boundaries for the Two-Dimensional Probability of Collision Calculation

The two-dimensional (2D) probability of collision (𝑃𝑐) estimation method relies on several assumptions that must be satisfied for accurate results. Monte Carlo analysis of ~44,000 conjunctions indicates that 2D-𝑃(sub 𝑐) pro-vides accurate estimates for most typical conjunctions, but occasionally underestimates 𝑃(sub 𝑐) significantly, indicating an assumption violation. A test to detect large-amplitude underestimation inaccuracies can be based on how much “offset-from-TCA” 2D-𝑃(sub 𝑐) values vary during a well-defined time interval bracketing closest approach. The test successfully detects all large-amplitude 2D-𝑃(sub 𝑐) underestimations found to date, but with a high false-alarm rate. The analysis also provides implementation recommendations and usage boundaries for the 2D-𝑃(sub 𝑐) method.

Hall, Doyle T.↗

NASA NTRS2019

Implementation Recommendations and Usage Boundaries for the Two-Dimensional Probability of Collision Calculation

Hall, Doyle T.↗

NASA NTRSDate not supplied

Tracking the Hunga Tonga-Hunga Ha’apai Eruption Stratospheric Aerosol and Trace Gas Plumes Using Machine Learning

The Hunga Tonga-Hunga Ha’apai (HTHH) submarine volcano had an explosive eruption phase on January 15, 2022, that thrusted ash, gases, and water vapor through the troposphere and into the stratosphere. The stratospheric volcanic plume included aerosol precursor gases such as SO2 and H2S as well as anomalously high water vapor concentrations due to the submarine oceanic origin. With these atmospheric constituents, the sulfuric gases and water vapor formed sulfate (SO4) particles via gas-to-particle reactions and these aerosols likely increased in size due to hygroscopic growth within anomalously humid regions. Strong easterlies and gravity waves propagated the volcanic impacts throughout the stratosphere. Orbital and suborbital passive sensor retrievals detected changes in the aerosol and trace gas characteristics within the atmospheric column for cloud-free regions over the southern hemisphere. While the CALIPSO lidar can detect aerosol layers in the stratosphere, passive sensors such as MODIS retrieved the total column aerosol abundance and characteristics. Previous studies used manual tracking methods to determine volcanic plume positions and compared them to ground observations. In this study, we examine the machine learning (ML) approaches including segmentation, object detection, and object tracking to identify and track aerosol and trace gas plumes using orbital and suborbital sensor data. This ML implementation strives to provide a more systematic approach to separate total column effects from those of the stratosphere. Similar ML tracking may be useful for stratospheric impact events observed historically by CALIPSO and in the future with EarthCare and the Atmosphere Observing System (AOS) lidar-capable missions.

Rhys Leahy↗

NASA NTRS2019

Assessing Reliability of NDE Flaw Detection Using Smaller Number of Demonstration Data Points

The paper provides an engineering analysis approach for assessing reliability of NDE flaw detection using smaller number of demonstration data points. It explores dependence of probability of detection (POD), probability of false positive (POF), on contrast-to-noise ratio, and net decision threshold-to-noise ratio in a simulated data; and draws some generically applicable inferences to devise the approach. ASTM nondestructive evaluation standards provide requirements on signal-to-noise ratio and/or contrast-to-noise ratio in order to provide reliable flaw detection and limit false positive calls. POD analysis of inspection test data results in an estimated flaw size, denoted by 𝑎90/95. This flaw size has 90% POD and minimum 95% confidence. POF is also estimated in the analysis. POD demonstration requires specimens with flaws of known size. In many situations, it is very expensive to produce the large number of flaws required for the POD analysis. In some situations, only real flaws can truly represent the flaws for demonstration. Real flaws of correct size and location in part configuration specimen may be difficult to produce, if not impossible. Here, an engineering analysis approach is devised using simulation to assess reliability of NDE technique when a limited number of flaws are available for demonstration. In this simulation, a technique is considered reliable, if it provides flaw detectability size equal to or better than the theoretical 𝑎90𝑡ℎ used in simulation and also provides a POF less than or equal to a chosen value. The paper uses simulated signal response versus flaw size data to devise the approach. Linear correlation is used between the signal response data and flaw size. POD software mh1823 uses generalized linear model (GLM) in POD analysis after transforming the flaw size and signal response, if needed, using logarithm. Therefore, this approach is in agreement with the linear signal correlation used in mh1823. Using the POD analysis of data, generic conditions on contrast-to-noise ratio and net decision threshold-to-noise ratio are derived for reliable flaw detection. In order to assess technique reliability using the engineering approach, signal response-to-flaw size correlation about the flaw size of concern is needed. In addition, measurement of noise is also needed. If the technique meets the above requirements, assumption of linear signal-to-flaw size correlation and conditions on noise, then the technique can be assessed using this analysis as it fits the underlying POD model used here. The approach is conservative and is designed to provide a larger flaw size compared to the POD approach. Such NDE technique assessment approach, although, not as rigorous as POD, can be cost effective if the larger flaw size can be tolerated. Typically, this is a situation for all quality control NDE inspections. Here, an NDE technique needs to be reliable and 𝑎90/95 is not estimated, but the assessed flaw size is assumed to be larger than the unknown a90 due to conservative factors or margins. Applicability of the approach for assessing reliability of flaw detection in x-ray radiography and 2D imaging in general is also explored.

Koshti, Ajay M.↗

NASA NTRS2009

Solder Joint Health Monitoring Testbed System

The density and pin count for Field Programmable Gate Arrays (FPGAs) has been increasing, and has exceeded current methods of solder joint inspection, making early detection of failures more problematic. These failures are a concern for both flight safety and maintenance in commercial aviation. Ridgetop Group, Inc. has developed a method for detecting solder joint failures in real time. The NASA Dryden Flight Research Center is developing a set of boards to test this method in ground environmental and accelerated testing as well as flight test on a Dryden F-15 or F-18 research aircraft. In addition to detecting intermittent and total solder joint failures, environmental data on the boards, such as temperature and vibration, will be collected and time-correlated to aircraft state data. This paper details the technical approach involved in the detection process, and describes the design process and products to date for Dryden s FPGA failure detection boards.

Delaney, Michael M.↗

NASA NTRS2010

Architectural Analysis of Dynamically Reconfigurable Systems

oTpics include: the problem (increased flexibility of architectural styles decrease analyzability, behavior emerges and varies depending on the configuration, does the resulting system run according to the intended design, and architectural decisions can impede or facilitate testing); top down approach to architecture analysis, detection of defects and deviations, and architecture and its testability; currently targeted projects GMSEC and CFS; analyzing software architectures; analyzing runtime events; actual architecture recognition; GMPUB in Dynamic SAVE; sample output from new approach; taking message timing delays into account; CFS examples of architecture and testability; some recommendations for improved testablity; and CFS examples of abstract interfaces and testability; CFS example of opening some internal details.

Lindvall, Mikael↗

NASA NTRS1996

Experimental Study of Collision Detection Schema Used by Pilots During Closely Spaced Parallel Approaches

An experimental flight simulator study was conducted to examine the mental alerting logic and thresholds used by subjects to issue an alert and execute an avoidance maneuver. Subjects flew a series of autopilot landing approaches with traffic on a closely-spaced parallel approach; during some runs, the traffic would deviate towards the subject and the subject was to indicate the point when they recognized the potential traffic conflict, and then indicate a direction of flight for an avoidance maneuver. A variety of subjects, including graduate students, general aviation pilots and airline pilots, were tested. Five traffic displays were evaluated, with a moving map TCAS-type traffic display as a baseline. A side-task created both high and low workload situations. Subjects appeared to use the lateral deviation of the intruder aircraft from its approach path as the criteria for an alert regardless of the display available. However, with displays showing heading and/or trend information, their alerting thresholds were significantly lowered. This type of range-only schema still resulted in many near misses, as a high convergence rate was often established by the time of the subject's alert. Therefore, the properties of the intruder's trajectory had the greatest effect on the resultant near miss rate; no display system reliably caused alerts timely enough for certain collision avoidance. Subjects' performance dropped significantly on a side-task while they analyzed the need for an alert, showing alert generation can be a high workload situation at critical times. No variation was found between subjects with and with out piloting experience. These results suggest the design of automatic alerting systems should take into account the range-type alerting schema used by the human, such that the rationale for the automatic alert should be obvious to, and trusted by, the operator. Although careful display design may help generate pilot/automation trust, issues such as user non-conformance to automatically generated commands can remain a possibility.

Pritchett, Amy R.↗

NASA NTRS2015

Online Dectection and Modeling of Safety Boundaries for Aerospace Application Using Bayesian Statistics

The behavior of complex aerospace systems is governed by numerous parameters. For safety analysis it is important to understand how the system behaves with respect to these parameter values. In particular, understanding the boundaries between safe and unsafe regions is of major importance. In this paper, we describe a hierarchical Bayesian statistical modeling approach for the online detection and characterization of such boundaries. Our method for classification with active learning uses a particle filter-based model and a boundary-aware metric for best performance. From a library of candidate shapes incorporated with domain expert knowledge, the location and parameters of the boundaries are estimated using advanced Bayesian modeling techniques. The results of our boundary analysis are then provided in a form understandable by the domain expert. We illustrate our approach using a simulation model of a NASA neuro-adaptive flight control system, as well as a system for the detection of separation violations in the terminal airspace.

Statistics↗

NASA NTRS1977

Some new control theoretic models for human operator display monitoring

Control theoretic techniques are applied to develop two new models for predicting human operator performance when monitoring an automatically controlled system. In one case it is assumed that the human monitors the instruments in order to rapidly detect failures. A second approach assumes that the instruments are sampled to best reconstruct the system status information. The relation of these models to existing prediction schemes, e.g., equal attention and the Senders model is explored. It is concluded that a combination of failure detection and status estimation models offers the best potential for human operator application.

Kleinman, D. L.↗

NASA NTRS1976

Some new control theoretic models for human operator display monitoring

Control theoretic techniques are applied to develop two new models for predicting human operator performance when monitoring an automatically controlled system. In one case it is assumed that the human monitors the instruments in order to rapidly detect failures. The second approach assumes that the instruments are sampled to best reconstruct the system status information. The relation of these models to existing prediction schemes, e.g., equal attention and the Sender's (1964) model is explored. It is concluded that a combination of failure detection and status estimation models offers the best potential for human operator application.

Kleinman, D. L.↗

NASA NTRS2024

Route-Recapturing State-Based Horizontal Maneuver Strategy for Automated Detect-and-Avoid

This report describes a novel approach to the development of a horizontal maneuver guidance strategy for Detect-and-Avoid systems. The maneuver guidance strategy provides a directive turn action that can be automatically executed by the vehicle’s auto-pilot system, taking into account the cost of recapturing the flight plan path. Pairwise conflict scenarios with non-accelerating intruders are simulated to validate the effectiveness of the maneuver guidance strategy. Initial results suggest the strategy is more effective for faster ownship than for slower ownship, which is unable to avoid conflict in certain scenarios against fast intruders. These findings indicate this novel approach shows great potential, but improvement to its performance is necessary and will be future work.

detect-and-avoid↗

NASA NTRS2020

Analytical Redundancy Using Kalman Filters for Rocket Engine Sensor Validation

The use of sensor redundancy is crucial in aerospace systems to maintain safe, reliable operation. While hardware redundancy is more common in application, analytical redundancy can provide a viable alternative in systems where the installation of multiple redundant sensors is not viable. To this end, the use of Kalman filters to analytically validate sensor measurements within rocket engines was explored. First, a dynamic model of the RS 25 engine, a derivative of the Space Shuttle Main Engine (SSME), was reduced to a subset of relations, focused around the main combustion chamber pressure. These relations were used within the Kalman filter algorithm to generate an estimate of sensor measurements to be compared with true measurements for data validation purposes. By using a bank of Kalman filters, the residuals between the estimated and true measurements were used to detect and isolate sensor faults. Through fault simulations, the sensor validation performance of this Kalman filter bank design was compared to a hardware redundancy check. Sensor bias and drift faults of various magnitudes were injected into nominal RS 25 engine test data. Results for both approaches show comparable fault detection with most bias faults found nearly instantaneously by both algorithms. Drift fault detection results show certain cases where one algorithm is faster than the other. The key advantage of the Kalman filter algorithm is shown in fault isolation performance where it can isolate faults between two redundant sensors while the hardware redundancy comparisons cannot.

sensors↗

NASA NTRS2017

Classification of Wildfires from MODIS Data Using Neural Networks

Wildfires are destructive to both life and property, which necessitates an approach to quickly and autonomously detect these events from orbital observatories. This talk will introduce a neural network based approach for classifying wildfires in MODIS multispectral data, and will show how it could be applied to a constellation of low-cost CubeSats. The approach combines training a deep neural network on the ground using high performance consumer GPUs, with a highly optimized inference system running on a flight-proven embedded processor. Normally neural networks execute on hardware orders of magnitude more powerful than anything found in a space-based computer, therefore the inference system is designed to be performance even on the most modest of platforms. This implementation is able to be significantly more accurate than previous neural network implementations, while also approaching the accuracy of the state-of-the-art MODFIRE data products.

Artificial Intelligence↗

NASA NTRS1993

Experimental evaluation of the certification-trail method

Certification trails are a recently introduced and promising approach to fault-detection and fault-tolerance. A comprehensive attempt to assess experimentally the performance and overall value of the method is reported. The method is applied to algorithms for the following problems: huffman tree, shortest path, minimum spanning tree, sorting, and convex hull. Our results reveal many cases in which an approach using certification-trails allows for significantly faster overall program execution time than a basic time redundancy-approach. Algorithms for the answer-validation problem for abstract data types were also examined. This kind of problem provides a basis for applying the certification-trail method to wide classes of algorithms. Answer-validation solutions for two types of priority queues were implemented and analyzed. In both cases, the algorithm which performs answer-validation is substantially faster than the original algorithm for computing the answer. Next, a probabilistic model and analysis which enables comparison between the certification-trail method and the time-redundancy approach were presented. The analysis reveals some substantial and sometimes surprising advantages for ther certification-trail method. Finally, the work our group performed on the design and implementation of fault injection testbeds for experimental analysis of the certification trail technique is discussed. This work employs two distinct methodologies, software fault injection (modification of instruction, data, and stack segments of programs on a Sun Sparcstation ELC and on an IBM 386 PC) and hardware fault injection (control, address, and data lines of a Motorola MC68000-based target system pulsed at logical zero/one values). Our results indicate the viability of the certification trail technique. It is also believed that the tools developed provide a solid base for additional exploration.

Sullivan, Gregory F.↗

NASA NTRS2017

Radar Detectability Studies of Slow and Small Zodiacal Dust Cloud Particles. III. The Role of Sodium and the Head Echo Size on the Probability of Detection

We present a path forward on a long-standing issue concerning the flux of small and slow meteoroids, which are believed to be the dominant portion of the incoming meteoric mass flux into the Earth's atmosphere. Such a flux, which is predicted by dynamical dust models of the Zodiacal Cloud, is not evident in ground-based radar observations. For decades this was attributed to the fact that the radars used for meteor observations lack the sensitivity to detect this population, due to the small amount of ionization produced by slow-velocity meteors. Such a hypothesis has been challenged by the introduction of meteor head echo (HE) observations with High Power and Large Aperture radars, in particular the Arecibo 430 MHz radar. Janches et al. developed a probabilistic approach to estimate the detectability of meteors by these radars and initially showed that, with the current knowledge of ablation and ionization, such particles should dominate the detected rates by one to two orders of magnitude compared to the actual observations. In this paper, we include results in our model from recently published laboratory measurements, which showed that (1) the ablation of Na is less intense covering a wider altitude range; and (2) the ionization probability, Beta ip, for Na atoms in the air is up to two orders of magnitude smaller for low speeds than originally believed. By applying these results and using a somewhat smaller size of the HE radar target we offer a solution that reconciles these observations with model predictions.

meteorites↗