Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffractometers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Molten salt flux synthesis and crystal structure of a new open-framework uranyl phosphate Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2}: Spectroscopic characterization and cationic mobility studies

The reaction of triuranyl diphosphate tetrahydrate precursor (UO{sub 2}){sub 3}(PO{sub 4}){sub 2}(H{sub 2}O){sub 4} with a CsI flux at 750 °C yields a yellow single crystals of new compound Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2}. The crystal structure (monoclinic, space group C2/c, a=13.6261 (13) Å, b=8.1081(8) Å, c=12.3983(12) Å, β=114.61(12)°, V=1245.41(20) Å{sup 3} with Z=4) has been solved using direct methods and Fourier difference techniques. A full-matrix least-squares refinement on the basis of F{sup 2} yielded R1=0.028 and wR2=0.071 for 79 parameters and 1352 independent reflections with I≥2σ(I) collected on a BRUKER AXS diffractometer with MoKα radiation and a charge-coupled device detector. The crystal structure is built by two independent uranium atoms in square bipyramidal coordination, connected by two opposite corners to form infinite chains {sup 1}{sub ∞}[UO{sub 5}] and by one phosphorus atom in a tetrahedral environment PO{sub 4}. The two last entities {sup 1}{sub ∞}[UO{sub 5}] and PO{sub 4} are linked by sharing corners to form a three-dimensional structure presenting different types of channels occupied by Cs{sup +} alkaline cations. Their mobility within the tunnels were studied between 280 and 800 °C and compared with other tunneled uranyl minerals. The infrared spectrum shows a good agreement with the values inferred from the single crystal structure analysis of uranyl phosphate compound. - Graphical abstract: Arrhenius plot of the electrical conductivity of tunneled compounds Cs{sub 3}U{sub 2}PO{sub 10} and CsU{sub 2}Nb{sub 2}O{sub 11.5}. Highlights: ► The reaction of (UO{sub 2}){sub 3}(PO{sub 4}){sub 2}(H{sub 2}O){sub 4} in excess of molten CsI leads to single-crystals of new tunneled compound Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2}. ► Ionic conductivity measurements and crystal structure analysis indicate a strong connection of the Cs{sup +} cations to the tunnels. ► A low symmetry in Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2} is the cause of IR activation and splitting of the bands in the IR spectrum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New high pressure rare earth tantalates RE{sub x}Ta{sub 2}O{sub 5+1.5x} (RE=La, Eu, Yb)

Rare earth tantalates La{sub 0.075}Ta{sub 2}O{sub 5.113}, Eu{sub 0.089}Ta{sub 2}O{sub 5.134} and Yb{sub 0.051}Ta{sub 2}O{sub 5.077} have been prepared by solid state reaction at P=7.0 GPa and T=1050–1100 °C and studied by X-ray diffraction, thermal analysis and electron microscopy. Low hydrated amorphous tantalum, lanthanum, europium and ytterbium hydroxides were used as starting materials. Aqueous as well as anhydrous compounds were obtained. Title tantalates are crystallized in the structure type of F–Ta{sub 2}O{sub 5} [Zibrov et al. Russ. J. Inorg. Chem. 48 (2003) 464–471] [5]. The structure was refined by the Rietveld method from X-ray powder diffractometer data: La{sub 0.075}Ta{sub 2}O{sub 5.113}, a=10.5099(2), b=7.2679(1), c=6.9765(1) Å, V=532.90(1) Å{sup 3}, Z=6, space group Ibam; Eu{sub 0.089}Ta{sub 2}O{sub 5.134}, a=10.4182(3), b=7.2685(1), c=6.9832(1) Å, V=528.80(2) Å{sup 3}, Z=6, space group Ibam; Yb{sub 0.051}Ta{sub 2}O{sub 5.077}, a=10.4557(2), b=7.3853(1), c=6.8923(1) Å, V=532.21(1) Å{sup 3}, Z=6, space group Ibam. RE atoms do not replace the tantalum in its positions but the only water in the channels of the structure. Highly charged cations RE{sup +3} compress the unit cell so that its volume becomes less than that of F–Ta{sub 2}O{sub 5}. Significant decrease of the unit cell volume after water removal from the structure is possible due to the puckering of pentagonal bipyramid layers and change of the corrugation angle in the layer. - Graphical abstract: The structure of RE{sub x}Ta{sub 2}O{sub 5+1.5x} and its HRTEM image (“A” arrows show empty channel, “B” arrows show filled channel). - Highlights: • We synthesized new tantalates of RE under high pressure high temperature conditions. • RE atoms replace water molecules in the channels of the structure. • Aqueous as well as anhydrous tantalates were obtained. • Highly charged cations RE{sup +3} compress the unit cell decreasing RE–O distances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facile synthesis of novel Ag/AgI/BiOI composites with highly enhanced visible light photocatalytic performances

Novel Ag/AgI/BiOI composites were controllably synthesized via a facile ion-exchange followed by photoreduction strategy by using hierarchical BiOI microflower as substrate. The as-prepared Ag/AgI/BiOI composites were studied by X-ray powder diffractometer (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET) surface area analyzer and UV–vis diffuse reflectance spectroscopy (DRS). Under visible light (λ>420 nm), Ag/AgI/BiOI displayed highly enhanced photocatalytic activities for degradation of methyl orange (MO) compared to the pure hierarchical BiOI, which was mainly ascribed to the highly efficient separation of electrons and holes through the closely contacted interfaces in the Ag/AgI/BiOI ternary system. - Graphical abstract: Ag/AgI/BiOI displayed excellent photocatalytic activities for methyl orange degradation under visible light, which was mainly ascribed to the highly efficient separation of electrons and holes through Z-scheme pathway. Display Omitted - Highlights: • Novel Ag/AgI/BiOI composites were successfully synthesized. • Ag/AgI/BiOI displayed higher visible light activities than those of pure BiOI and AgI. • ·O{sub 2}{sup −} and h{sup +}, especially ·O{sub 2}{sup −}, dominated the photodegradation process of MO. • A Z-scheme pattern was adopted for Ag/AgI/BiOI activity enhancement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-pressure high-temperature crystal growth of equiatomic rare earth stannides RENiSn and REPdSn

The two series of equiatomic rare earth (RE) stannides RENiSn and REPdSn were systematically studied with respect to high-pressure modifications. The normal-pressure (NP) low-temperature (LT) modifications were synthesized by arc-melting and subsequently treated under high-pressure (P{sub max}=11.5 GPa) and high-temperature (T{sub max}=1570 K) conditions in a Walker-type multi-anvil press. The pressure and temperature conditions were systematically varied in order to improve the crystallization conditions. The new ZrNiAl-type high-pressure modifications HP-RENiSn (RE=Sc, Y, La, Gd–Lu) and HP-REPdSn (RE=Y, Sm–Dy) were obtained in 80 mg quantities, several of them in X-ray pure form. Some of the REPdSn stannides with the heavy rare earth elements show high-temperature (HT) modifications. The structures of HP-ScNiSn, HP-GdNiSn, HP-DyNiSn (both ZrNiAl-type), NP-YbNiSn, and HT-ErPdSn (both TiNiSi-type) were refined from single crystal diffractometer data, indicating full ordering of the transition metal and tin sites. TiNiSi-type NP-EuPdSn transforms to MgZn{sub 2}-type HP-EuPdSn: P6{sub 3}/mmc, a=588.5(2), c=917.0(3) pm, wR2=0.0769, 211 F{sup 2} values, 11 variables. The structure refinement indicated statistical occupancy of the palladium and tin sites on the tetrahedral network. The X-ray pure high-pressure phases were studied with respect to their magnetic properties. HP-YPdSn is a Pauli paramagnet. The susceptibility data of HP-TbNiSn, HP-DyNiSn, HP-GdPdSn, and HP-TbPdSn show experimental magnetic moments close to the free ion values of RE{sup 3+} and antiferromagnetic ordering at low temperature with the highest Néel temperature of 15.8 K for HP-TbPdSn. HP-SmPdSn shows the typical Van Vleck type behavior along with antiferromagnetic ordering at T{sub N}=5.1 K. HP-EuPdSn shows divalent europium and antiferromagnetic ordering at 8.9 K followed by a spin reorientation at 5.7 K. - Graphical abstract: Packing of the polyhedra in the high-pressure phase of EuPdSn. - Highlights: • High-pressure phases of the stannides RENiSn and REPdSn. • Crystal growth conditions. • Pressure- and temperature-driven phase transitions. • Magnetic properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrogenation studies on NdScSi and NdScGe

NdScSi and NdScGe were synthesized from the elements via arc-melting and subsequent annealing. Their ordered La{sub 2}Sb type structures, with space group I4/mmm, were refined from single crystal X-ray diffractometer data: a=428.94(6) and b=1570.5(3) pm, wR2=0.0395, 309 F{sup 2} values for NdScSi and a=431.2(1) and c=1581.3(5) pm, wR2=0.1220, 227 F{sup 2} values for NdScGe, with 11 variables per refinement. Hydrogen insertion was performed on both Nd-based intermetallics by solid/gas reaction. Hydrogen uptake keeps the pristine compound space group but yields an anisotropic expansion of the unit cell with a large increase of c (≈+7%) and a slight decrease of a (≈−1.7%) parameters. Hydrogen absorption at 350 °C and under 5 bar of H{sub 2} pressure shows that the hydride NdScSiH{sub 1.48(5)} is formed. An in-situ neutron diffraction study during the deuteration of NdScSi reveals for the first time in a CeScSi-type compound, the possibility to fill two interstitial sites with deuterium atoms, leading to the composition NdScSiD{sub 1.5} for the deuteride adopting then the La{sub 2}Fe{sub 2}Se{sub 2}O{sub 3}-type structure. From magnetization measurements, we evidence that hydrogenation strongly reduces the Curie temperature of NdScSi (T{sub C}=175 K) and NdScGe (T{sub C}=194 K) since NdScSiH{sub 1.5} and NdScGeH{sub x} undergo a magnetic transition at 4 K and around 2 K, respectively. - Highlights: • Crystal structures of NdScSi and NdScGe were refined from single crystal XRD data. • The hydrogenation of NdScSi leads to the formation of the NdScSiH{sub 1.5} hydride. • NdScSiD{sub 1.5} adopts the La{sub 2}Fe{sub 2}Se{sub 2}O{sub 3}-type structure. • Hydrogenation strongly reduces the ordering temperature of both intermetallics.

36 MATERIALS SCIENCE↗

Enhanced performance of dye-sensitized solar cells based on organic dopant incorporated PVDF-HFP/PEO polymer blend electrolyte with g-C{sub 3}N{sub 4}/TiO{sub 2} photoanode

This work describes the effect of 2-aminopyrimidine (2-APY) on poly(vinylidinefluoride-co-hexafluoropropylene) (PVDF-HFP)/polyethylene oxide (PEO) blend polymer electrolyte along with binary iodide salts (tetrabutylammonium iodide (TBAI) and potassium iodide (KI)) and iodine (I{sub 2}) were studied for enhancing the efficiency of the dye-sensitized solar cells (DSSCs) consisting of g-C{sub 3}N{sub 4}/TiO{sub 2} composite as photoanode. The g-C{sub 3}N{sub 4} was synthesized from low cost urea by thermal condensation method. It was used as a precursor to synthesize the various weight percentage ratios (5%, 10% and 15%) of g-C{sub 3}N{sub 4}/TiO{sub 2} composites by wet-impregnation method. The pure and 2-APY incorporated PVDF-HFP/PEO polymer blend electrolytes were arranged by wet chemical process (casting method) using DMF as a solvent. The synthesized g-C{sub 3}N{sub 4}/TiO{sub 2} composites and polymer blend electrolytes were studied and analyzed by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffractometer (XRD) and scanning electron microscopy (SEM). The ionic conductivity values of the pure and 2-APY incorporated PVDF-HFP/PEO blend electrolytes were estimated to be 4.53×10{sup −5} and 1.87×10{sup −4} Scm{sup −1} respectively. The UV–vis absorption spectroscopy was carried out for the pure and different wt% of g-C{sub 3}N{sub 4}/TiO{sub 2} composites coated FTO films after N3 dye-sensitization. The 10 wt% g-C{sub 3}N{sub 4}/TiO{sub 2} composite film showed a maximum absorption compared to the others. The DSSC assembled with 10 wt% g-C{sub 3}N{sub 4}/TiO{sub 2} as photoanode using the pure polymer blend electrolyte exhibited a power conversion efficiency (PCE) of 3.17% , which was superior than that of DSSC based pure TiO{sub 2} (2.46%). However, the PCE was increased to 4.73% for the DSSC assembled using 10 wt% g-C{sub 3}N{sub 4}/TiO{sub 2} as photoanode with 2-APY incorporated polymer blend electrolyte. Hence, the present study is a successful attempt to provide a new pathway to enhance the performance of DSSCs. - Graphical abstract: In this study, the g-C{sub 3}N{sub 4} was synthesized from low cost urea and it was used as a precursor to synthesize of g-C{sub 3}N{sub 4}/TiO{sub 2} composite. The pure and 2-APY incorporated PVDF-HFP/PEO electrolytes were fabricated by solution casting method. A remarkably enhanced PCE of 4.73% was observed for 2-APY incorporated PVDF-HFP/PEO electrolyte with g-C{sub 3}N{sub 4}/TiO{sub 2} composite photoanode based DSSC. - Highlights: • 2-APY added PVDF-HFP/PEO electrolyte was prepared by solution casting method. • The g-C{sub 3}N{sub 4}/TiO{sub 2} composites were synthesized by wet-impregnation method. • DSSC with g-C{sub 3}N{sub 4}/TiO{sub 2} and 2-APY added electrolyte showed the efficiency of 4.73 %. • The g-C{sub 3}N{sub 4} and 2-APY can be a useful dopant to enhance the performance of DSSCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ternary germanides RERhGe{sub 2} (RE = Y, Gd-Ho) – New representatives of the YIrGe{sub 2} type

The YIrGe{sub 2} type ternary germanides RERhGe{sub 2} (RE = Y, Gd-Ho) were synthesized from the elements by arc-melting and characterized by powder X-ray diffraction. The structure of DyRhGe{sub 2} was refined from single crystal X-ray diffractometer data: Immm, a = 426.49(9), b = 885.0(2), c = 1577.4(3) pm, wR2 = 0.0533, 637 F{sup 2} values, 30 variables (300 K data). The structure contains two crystallographically independent dysprosium atoms in pentagonal prismatic and hexagonal prismatic coordination. The three-dimensional [RhGe{sub 2}] polyanion is stabilized through covalent Rh–Ge (243–261 pm) and Ge–Ge (245–251 pm) bonding. The close structural relationship with the slightly rhodium-poorer germanides RE{sub 5}Rh{sub 4}Ge{sub 10} (≡ RERh{sub 0.8}Ge{sub 2}) is discussed. Temperature-dependent magnetic susceptibility measurements reveal Pauli paramagnetism for YRhGe{sub 2} and Curie-Weiss paramagnetism for RERhGe{sub 2} with RE = Gd, Tb, Dy and Ho. These germanides order antiferromagnetically at T{sub N} = 7.2(5), 10.6(5), 8.1(5), and 6.4(5) K, respectively. - Graphical abstract: The germanides RERhGe{sub 2} (RE = Y, Gd-Ho) are new representatives of the YIrGe{sub 2} type.

36 MATERIALS SCIENCE↗

Nanostructured Al{sub 2}O{sub 3}-TiO{sub 2} coatings for high-temperature protection of titanium alloy during ablation

Plasma-sprayed nanostructured Al{sub 2}O{sub 3}-13 wt.%TiO{sub 2} coatings were successfully fabricated on titanium alloys (Ti-6Al-4V) using as-prepared feedstock. Ablation experiments for the titanium alloy samples with or without a coating were carried out using a Metco 9MB plasma gun. The microstructure, phase constituents and mechanical properties of the titanium alloys before and after ablation were investigated by scanning electron microscope (SEM), X-ray diffractometer (XRD) and Vickers hardness tester. The surface morphologies, cross-sectional microstructure and hardness of titanium alloys with coatings are similar before and after ablation. In contrast, the microstructure and mechanical properties of the titanium alloy without coating are significantly changed after ablation. The surface coating is found to serve as a protective coating during ablation.

36 MATERIALS SCIENCE↗

Structure and mechanical properties of as-cast Ti-5Nb-xFe alloys

In this study, as-cast Ti-5Nb and a series of Ti-5Nb-xFe alloys were investigated and compared with commercially pure titanium (c.p. Ti) in order to determine their structure and mechanical properties. The series of Ti-5Nb-xFe alloys contained an iron content ranging from 1 to 5 mass% and were prepared by using a commercial arc-melting vacuum-pressure casting system. Additionally, X-ray diffraction (XRD) for phase analysis was conducted with a diffractometer, and three-point bending tests were performed to evaluate the mechanical properties of all specimens. The fractured surfaces were observed by using scanning electron microscopy (SEM). The experimental results indicated that these alloys possessed a range of different structures and mechanical properties dependent upon the various additions of Fe. With an addition of 1 mass% Fe, retention of the metastable {beta} phase began. However, when 4 mass% Fe or greater was added, the {beta} phase was entirely retained with a bcc crystal structure. Moreover, the {omega} phase was only detected in the Ti-5Nb-2Fe, Ti-5Nb-3Fe and Ti-5Nb-4Fe alloys. The largest quantity of {omega} phase and the highest bending modulus were found in the Ti-5Nb-3Fe alloy. The Ti-5Nb-2Fe alloy had the lowest bending modulus, which was lower than that of c.p. Ti by 20%. This alloy exhibited the highest bending strength/modulus ratio of 26.7, which was higher than that of c.p. Ti by 214%, and of the Ti-5Nb alloy (14.4 ) by 85%. Additionally, the elastically recoverable angles of the ductile Ti-5Nb-1Fe (19.9{sup o}) and Ti-5Nb-5Fe (29.5{sup o}) alloys were greater than that of c.p. Ti (2.7{sup o}) by as much as 637% and 993%, respectively. Furthermore, the preliminary cell culturing results revealed that the Ti-5Nb-xFe alloys were not only biocompatible, but also supported cell attachment.

36 MATERIALS SCIENCE↗

(110) Orientation growth of magnetic metal nanowires with face-centered cubic structure using template synthesis technique

A template-assisted assembly technique has been used to synthesize magnetic metal nanowire arrays. Fe, Co, Ni nanowires are fabricated using direct-current electrodeposition in the pores of anodic alumina membranes. The morphology and the crystal structure of the samples are characterized by field-emission scanning electron microscopy, transmission electron microscopy, and X-ray diffractometer. The results indicate that Fe, Co, and Ni nanowires all have face-centered cubic (FCC) structure and a preferred orientation along the [110] direction. The ability to prepare well-defined orientation growth of magnetic metal nanowires with FCC structure opens up new opportunities for both fundamental studies and nanodevice applications. - Research Highlights: {yields} Fe, Co, and Ni nanowires are fabricated in the AAM templates by electrodeposition. {yields} Well-defined orientation growth of the nanowires with FCC structure were investigated. {yields} The electrodeposition parameters affect the crystal structure and growth orientation.

36 MATERIALS SCIENCE↗

Brazing ZrO{sub 2} ceramic to Ti–6Al–4V alloy using NiCrSiB amorphous filler foil: Interfacial microstructure and joint properties

Reliable brazing of ZrO{sub 2} ceramic and Ti–6Al–4V alloy was achieved using NiCrSiB amorphous filler foil. The interfacial microstructure of ZrO{sub 2}/Ti–6Al–4V joints was characterized by scanning electron microscope, energy dispersive spectrometer and micro-focused X-ray diffractometer. The effects of brazing temperature on the interfacial microstructure and joining properties of brazed joints were investigated in detail. Active Ti of Ti–6Al–4V alloy dissolved into molten filler metal and reacted with ZrO{sub 2} ceramic to form a continuous TiO reaction layer, which played an important role in brazing. Various reaction phases including Ti{sub 2}Ni, Ti{sub 5}Si{sub 3} and β-Ti were formed in brazed joints. With an increasing of brazing temperature, the TiO layer thickened gradually while the Ti{sub 2}Ni amount reduced. Shear test indicated that brazed joints tend to fracture at the interface between ZrO{sub 2} ceramic and brazing seam or Ti{sub 2}Ni intermetallic layer. The maximum average shear strength reached 284.6 MPa when brazed at 1025 °C for 10 min. - Graphical Abstract: Interfacial microstructure of ZrO{sub 2}/TC4 joint brazed using NiCrSiB amorphous filler foil was: ZrO{sub 2}/TiO/Ti{sub 2}Ni + β-Ti + Ti{sub 5}Si{sub 3}/β-Ti/Widmanstätten structure/TC4. - Highlights: • Brazing of ZrO{sub 2} ceramic and Ti-6Al-4V alloy was achieved. • Interfacial microstructure was TiO/Ti{sub 2}Ni + β + Ti{sub 5}Si{sub 3}/β/Widmanstätten structure. • The formation of TiO produced the darkening effect of ZrO{sub 2} ceramic. • The highest joining strength of 284.6MPa was obtained.

36 MATERIALS SCIENCE↗

In situ X-ray diffraction strain-controlled study of Ti–Nb–Zr and Ti–Nb–Ta shape memory alloys: crystal lattice and transformation features

Phase and structure transformations in biomedical Ti–21.8Nb–6.0Zr (TNZ) and Ti–19.7Nb–5.8Ta (TNT) shape memory alloys (at.%) under and without load in the − 150 to 100 °S temperature range are studied in situ using an original tensile module for a low-temperature chamber of an X-ray diffractometer. Alpha″- and beta-phase lattice parameters, the crystallographic resource of recovery strain, phase and structure transformation sequences, and microstress appearance and disappearance are examined, compared and discussed. For both alloys, the crystallographic resource of recovery strain decreases with temperature increase to become 4.5% for TNZ and 2.5% for TNT alloy (at RT). Loading at low temperatures leads to additional α″-phase formation and reorientation. Heating under load, as compared to strain-free heating, affects the reverse transformation sequence of both alloys in different ways. For TNZ alloy, strain-free heating results in simultaneous ω→β and α″→β transformations, whereas during heating under stress, they are sequential: β + ω→α″ precedes α″→β. For TNT alloy, strain-free heating results in reverse α″→β transformation, whereas during heating under stress, α″→β transformation is preceded by α″-phase reorientation. - Highlights: • Comparative in situ XRD analysis of Ti–Nb–Zr(Ta) shape memory alloys is realized. • Lattice parameters of β- and α″-phases are calculated in the − 150 to + 100 °C range. • The higher the temperature, the lower the α″→β transformation strain. • Loading at low temperatures results in α″-phase formation and reorientation. • Transformation sequences upon heating with and without loading are different.

36 MATERIALS SCIENCE↗

Residual strain mapping of Roman styli from Iulia Concordia, Italy

Iulia Concordia is an important Roman settlement known for the production of iron objects and weapons during the Roman Empire. A huge number of well-preserved styli were found in the past century in the bed of an old channel. In order to shed light about the production processes used by Roman for stylus manufacturing, a neutron diffraction residual strain analysis was performed on the POLDI materials science diffractometer at the Paul Scherrer Institut in Switzerland. Here, we present results from our investigation conducted on 11 samples, allowing to define, in a non-invasive way, the residual strain map related to the ancient Roman working techniques. - Highlights: • We examined 11 Roman styli from the settlement of Iulia Concordia, Italy. • We performed a neutron diffraction residual strain analysis on POLDI at PSI (CH). • We identified the production processes used by Roman for stylus manufacturing. • We clarified the way and direction of working applied for different classes of styli.

36 MATERIALS SCIENCE↗

High-resolution neutron diffraction study of microstructural changes in nanocrystalline ball-milled niobium carbide NbC{sub 0.93}

High resolution neutron diffraction was applied for elucidating of the microstructural evolution of nanocrystalline niobium carbide NbC{sub 0.93} powders subjected to high-energy ball milling. The diffraction patterns were collected with the high resolution Fourier diffractometer HRFD by using the reverse time-of-flight (RTOF) mode of data acquisition. The traditional single diffraction line analysis, the Rietveld method and more advanced Whole Powder Pattern Modeling technique were applied for the data analysis. The comparison of these techniques was performed. It is established that short-time milling produces a non-uniform powder, in which two distinct fractions with differing microstructure can be identified. Part of the material is in fact milled efficiently, with a reduction in grain size, an increase in the quantity of defects, and a corresponding tendency to decarburize reaching a composition NbC{sub 0.80} after 15 h of milling. The rest of the powder is less efficiently processed and preserves its composition and lower defect content. Larger milling times should have homogenized the system by increasing the efficiently milled fraction, but the material is unable to reach a uniform and homogeneous state. It is definitely shown that RTOF neutron diffraction patterns can provide the very accurate data for microstructure analysis of nanocrystalline powders. - Highlights: • The NbC{sub 0.93} powder was processed by high-energy ball milling. • The microstrain and dislocation density increase with milling time increase. • The corresponding decrease in crystallite size with milling time was observed. • The material exhibits the presence of two fractions after ball milling. • The RTOF neutron diffraction data are suitable for accurate microstructure analysis.

36 MATERIALS SCIENCE↗

Molecular self-assembled designing and characterization of TiO2 NPs-CdS QDs-dye composite for photoanode materials

Highlights: • Initially TiO{sub 2} NPs were synthesized by sol-gel method and CdS QDs by one pot synthesis method. • The connectivity between TiO{sub 2} NPs and CdS QDs was well revealed by zeta potential and FTIR techniques. • This binary system was sensitized with N719 dye molecule for better photoanode material. • Ternary TiO{sub 2} NPs-CdS QDs-N719 dye photoanode showed higher conversion efficiency than its binary photoanode devices. - Abstract: Ternary based photoanodes have been prepared by using titanium dioxide (TiO{sub 2}) nanoparticles (NPs), cadmium sulfide (CdS) quantum dots (QDs) and N719 dye. Initially, CdS QDs and TiO{sub 2} NPs were synthesized by one pot synthesis and sol-gel method, respectively. CdS QDs were connected electrostatically to the surfaces of TiO{sub 2} NPs, and after that, this binary hybrid further self-assembled with N719 dye to form the composites. The NPs, QDs and the resultant composites are characterized by using different techniques. The connectivity of these anatase TiO{sub 2} NPs with cubic CdS QDs are confirmed by FTIR; while the broad coverage of these materials is studied through UV–Visible diffuse reflectance spectroscopy (DRS). The surface topology and the cross-sectional morphology of thin films are studied by high resolution transmission electron microscopy (HR-TEM) and field emission scanning electron microscopy (FE-SEM) techniques; while the structural properties of NPs and QDs are studied by X-ray diffractometer (XRD). The synergetic co-sensitization of CdS and N719 dye significantly enhancing the overall power conversion efficiency (η) of TiO{sub 2} up to 2.37% (J{sub sc} = 10.31 mA/cm{sup 2} and V{sub oc} of 550 mV) (100 mW/cm{sup 2}). The J{sub sc}, V{sub oc}, and η values along with Incident photon to current conversion efficiency (IPCE) value of ternary photoelectrode-based solar devices, is almost double to that of either binary TiO{sub 2} NPs-CdS QDs or binary TiO{sub 2} NPs-N719 binary systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Room temperature synthesis and photocatalytic property of AgO/Ag{sub 2}Mo{sub 2}O{sub 7} heterojunction nanowires

Graphical abstract: The AgO nanoparticles are attached on the surface of the Ag{sub 2}Mo{sub 2}O{sub 7} nanowires to form a heterojunction structure. The AgO nanoparticles start embedding into the nanowires with increasing reaction temperature or time. Highlights: ► AgO/Ag{sub 2}Mo{sub 2}O{sub 7} heterojunction NWs were synthesized at room temperature for the first time. ► AgO particles embed into the Ag{sub 2}Mo{sub 2}O{sub 7} NWs with increase in reaction time and temperature. ► The heterojunction NWs display much better photocatalytic activity than the none-heterojunction NWs. ► The catalytic mechanism was proposed. -- Abstract: AgO/Ag{sub 2}Mo{sub 2}O{sub 7} heterojunction nanowires were synthesized at temperatures of 25 °C, 50 °C, 80 °C, and 110 °C, under magnetic stirring in solution reaction. The catalytic activity of AgO/Ag{sub 2}Mo{sub 2}O{sub 7} nanowires was evaluated by the degradation of Rhodmine B dye under the irradiation of the simulated sunlight. The synthesized samples were characterized by X-ray diffractometer, energy dispersive spectrometry, X-ray photoelectron spectrometer, scanning electron microscopy, and transmission electron microscopy. The results show that the AgO nanoparticles are attached on the surface of the Ag{sub 2}Mo{sub 2}O{sub 7} nanowires to form a heterojunction structure. The length of the nanowires is up to 10 μm and the size of the AgO nanoparticles is 10–20 nm. The length of nanowires increases with increasing reaction time and temperature while the AgO particles are gradually embedded into the nanowires. The photocatalytic activity is greatly improved for the AgO/Ag{sub 2}Mo{sub 2}O{sub 7} heterojunction nanowires compared with that of the pure Ag{sub 2}Mo{sub 2}O{sub 7} nanowires, indicating a remarkable role of AgO particles on the Ag{sub 2}Mo{sub 2}O{sub 7} nanowires in the photodegradation.

36 MATERIALS SCIENCE↗

A self-propagation high-temperature synthesis and annealing route to synthesis of wave-like boron nitride nanotubes

Highlights: ► Large quantities of wave-like BN nanotubes were synthesized by SHS-annealing method. ► The catalytic boron-containing porous precursor was produced by self-propagation high-temperature synthesis method. ► Three growth models were proposed to explain the growth mechanism of the wave-like BN nanotubes. - Abstract: Large quantities of boron nitride (BN) nanotubes were synthesized by annealing a catalytic boron-containing porous precursor in flowing NH{sub 3} gas at 1180 °C. The porous precursor was prepared by self-propagation high-temperature synthesis (SHS) method at 800 °C using Mg, B{sub 2}O{sub 3} and amorphous boron powder (α-B) as the starting materials. The porous precursor played an important role in large quantities synthesis of BN nanotubes. The as-synthesized product was characterized by X-ray diffractometer (XRD), Fourier transform infrared spectrometer (FTIR), Raman, Scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (EDS), Transmission electron microscopy (TEM) and High-resolution transmission electron microscopy (HRTEM). Characterization results indicated that the BN nanotubes displayed wave-like inner structures with diameters in the range of 50–300 nm and average lengths of more than 10 μm. The possible growth mechanism of the BN nanotubes was also discussed.

36 MATERIALS SCIENCE↗

Simple polyol route to synthesize heptanoic acid coated magnetite (Fe{sub 3}O{sub 4}) nanoparticles

Highlights: ► Heptanoic acid@Fe{sub 3}O{sub 4} nanocomposite has been prepared via simple polyol. ► Heptanoic acid used as both surfactant and solvents. ► Magneto polymer composite with adjustable Ea has a potential usage as functional composites. - Abstract: Magnetite (Fe{sub 3}O{sub 4}) nanoparticles were prepared via polyol method by using FeCl{sub 2} as only source of iron. As-prepared samples were characterized by powder X-ray diffractometer (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), thermal gravimetric analyzer (TGA) and vibrating sample magnetometer (VSM). Crystalline phase was identified as Fe{sub 3}O{sub 4} and the crystallite sizes were calculated as 19.1 ± 1.1 and 22 ± 1.3 nm for uncalcinated and calcinated products from X-ray line profile fitting. The capping of heptanoic acid around Fe{sub 3}O{sub 4} nanoparticles was confirmed by FT-IR spectroscopy, the interaction being via bridging oxygen's of the carboxylate and the nanoparticle surface and also by TG analysis. VSM measurements showed that both samples exhibited typical superparamagnetic behavior at room temperature with different Ms values. The ε′ decreases with increasing frequency for both composites and permeability has almost same values for all temperatures at higher frequencies. As synthesized and calcinated samples conductivity increase linearly with the temperature.

36 MATERIALS SCIENCE↗