Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Co-localised Raman and force spectroscopy reveal the roles of hydrogen bonds and π-π interactions in defining the mechanical properties of diphenylalanine nano- and micro-tubes

An integrated atomic force and polarized Raman microscope were used to measure the elastic properties of individual diphenylalanine (FF) nano- and micro-tubes and to obtain quantitative information regarding the inter-molecular interactions that define their mechanical properties. For individual tubes, co-localised force spectroscopy and Raman spectroscopy measurements allowed the calculation of the Young's and shear moduli (25 ± 5 GPa and 0.28 ± 0.05 GPa, respectively) and the contribution of hydrogen bonding network to the Young's modulus (∼17.6 GPa). The π-π interactions between the phenyl rings, dominated by T-type arrangements, were estimated based on previously published X-ray data to only 0.20 GPa. These results provide experimental evidence obtained from individual FF tubes that the network of H-bonds dominates the elastic properties of the FF tubes.

36 MATERIALS SCIENCE↗

First-principles studies of Al-Ni intermetallic compounds

The structural properties, heats of formation, elastic properties, and electronic structures of Al-Ni intermetallic compounds are analyzed here in detail by using density functional theory. Higher calculated absolute values of heats of formation indicate a very strong chemical interaction between Al and Ni for all Al-Ni intermetallic compounds. According to the computational single crystal elastic constants, all the Al-Ni intermetallic compounds considered here are mechanically stable. The polycrystalline elastic modulus and Poisson's ratio have been deduced by using Voigt, Reuss, and Hill (VRH) approximations, and the calculated ratio of shear modulus to bulk modulus indicated that AlNi, Al{sub 3}Ni, AlNi{sub 3} and Al{sub 3}Ni{sub 5} compounds are ductile materials, but Al{sub 4}Ni{sub 3} and Al{sub 3}Ni{sub 2} are brittle materials. With increasing Ni concentration, the bulk modulus of Al-Ni intermetallic compounds increases in a linear manner. The electronic energy band structures confirm that all Al-Ni intermetallic compounds are conductors. - Graphical abstract: Calculated bulk modulus compared to experimental and other theoretical values for the Al-Ni intermetallic compounds.

36 MATERIALS SCIENCE↗

First-Principles Calculations of Acoustic and Anharmonic Properties of Ferromagnetic Cu{sub 2}MnZ (Z = Al and In) Heusler Alloys

The acoustic and anharmonic properties of ferromagnetic Cu{sub 2}MnZ (Z = Al and In) Heusler alloys have been investigated by first-principles calculations method. The obtained lattice parameters, magnetic moments, elastic properties are found to be in good agreement with the available experimental values. From the elastic properties, the sound velocities and the related Debye temperatures and minimum thermal conductivities have been obtained for the two alloys. The sound velocities and thermal conductivities of both alloys are found to show significant anisotropy, and the Cu{sub 2}MnAl with small density and large elastic constants has large sound velocities, high Debye temperature, and large thermal conductivities. Also, the effective second-order elastic constants, generalized Grüneisen constants, and nonlinear ultrasonic parameters to characterize anharmonic properties have been studied for the two alloys. These predictions on the acoustic and anharmonic properties can provide a valuable guidance or reference for further related investigations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Pd alloying on structural, electronic and magnetic properties of L1 0 Fe–Ni

We present a systematic study of the effect of Pd-alloying on phase stability, electronic structure, and elastic properties in L1 0 Fe–Ni using density-functional theory. Being from the same group of the periodic table, Pd is the best candidate for chemical alloying. The Fe–Ni/Fe–Pd/Ni–Pd bond-length increases with increasing Pd-concentration, which weakens the hybridization between low lying energy states below Fermi-level. The reduced hybridization decreases the relative thermodynamic stability of L1 0 Fe(Ni 1–x Pd x ) until x = 0.75. Beyond this concentration, the relative stability gets enhanced, which is attributed to a unique change in the lattice distortion (c/a). The elastic properties show a non-monotonous behavior as a function of x, which is again due to a specific change-over in the uniaxial strain. We found that Pd alloying increases the local Fe moment and structural anisotropy of L1 0 FeNi, which are important for applications such as microwave absorption, refrigeration systems, recording devices, imaging and sensors. Here, we believe that the present study for the chemical alloying effect can provide critical insights toward the understanding of electronic-structure and elastic behavior of other technologically important materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Identifying Heterogeneous Micromechanical Properties of Biological Tissues via Physics–Informed Neural Networks

The heterogeneous micromechanical properties of biological tissues have profound implications across diverse medical and engineering domains. However, identifying full-field heterogeneous elastic properties of soft materials using traditional engineering approaches is fundamentally challenging due to difficulties in estimating local stress fields. Recently, there has been a growing interest in data-driven models for learning full-field mechanical responses, such as displacement and strain, from experimental or synthetic data. However, research studies on inferring full-field elastic properties of materials, a more challenging problem, are scarce, particularly for large deformation, hyperelastic materials. Here, a physics-informed machine learning approach is proposed to identify the elasticity map in nonlinear, large deformation hyperelastic materials. This study reports the prediction accuracies and computational efficiency of physics-informed neural networks (PINNs) in inferring the heterogeneous elasticity maps across materials with structural complexity that closely resemble real tissue microstructure, such as brain, tricuspid valve, and breast cancer tissues. Further, the improved architecture is applied to three hyperelastic constitutive models: Neo-Hookean, Mooney Rivlin, and Gent. Furthermore, the improved network architecture consistently produces accurate estimations of heterogeneous elasticity maps, even when there is up to 10% noise present in the training data.

59 BASIC BIOLOGICAL SCIENCES↗

Atomistic Simulations of the Elastic Compression of Platinum Nanoparticles

Abstract The elastic behavior of nanoparticles depends strongly on particle shape, size, and crystallographic orientation. Many prior investigations have characterized the elastic modulus of nanoscale particles using experiments or simulations; however their reported values vary widely depending on the methods for measurement and calculation. To understand these discrepancies, we used classical molecular dynamics simulation to model the compression of platinum nanoparticles with two different polyhedral shapes and a range of sizes from 4 to 20 nm, loaded in two different crystal orientations. Multiple standard methods were used to calculate the elastic modulus from stress-vs-strain data for each nanoparticle. The magnitudes and particle-size dependence of the resulting moduli varied with calculation method and, even for larger nanoparticles where bulk-like behavior may be expected, the effective elastic modulus depended strongly on shape and orientation. Analysis of per-atom stress distributions indicated that the shape- and orientation-dependence arise due to stress triaxiality and inhomogeneity across the particle. When the effective elastic modulus was recalculated using a representative volume element in the center of a large nanoparticle, the elastic modulus had the expected value for each orientation and was shape independent. It is only for single-digit nanoparticles that meaningful differences emerged, where even the very center of the particle had a lower modulus due to the effect of the surface. These findings provide better understanding of the elastic properties of nanoparticles and disentangle geometric contributions (such as stress triaxiality and spatial inhomogeneity) from true changes in elastic properties of the nanoscale material.

36 MATERIALS SCIENCE↗

Single-Crystal Elastic Constants of Yttria (Y2O3) Measured to High Temperatures

Yttria, or yttrium sesquioxide (Y2O3), has been considered for use in nuclear applications and has gained interest relatively recently for use in infrared optics. Single crystals of yttria have been grown successfully at the NASA Glenn Research Center using a laser-heated float zone technique in a fiber and rod. Such samples allow measurement of the single-crystal elastic properties, and these measurements provide useful property data for the design of components using single crystals. They also yield information as to what degree the elastic properties of yttria ceramics are a result of the intrinsic properties of the yttria crystal in comparison to characteristics that may depend on processing, such as microstructure and intergranular phases, which are common in sintered yttria. The single-crystal elastic moduli are valuable for designing such optical components. In particular, the temperature derivatives of elastic moduli allow the dimensional changes due to heating under physical constraints, as well as acoustic excitation, to be determined. The single-crystal elastic moduli of yttria were measured by Brillouin spectroscopy up to 1200 C. The room-temperature values obtained were C(sub 11) = 223.6 + 0.6 GPa, C(sub 44) = 74.6 + 0.5 GPa, and C(sub 12) = 112.4 + 1.0 GPa. The resulting bulk and (Voigt-Reuss-Hill) shear moduli were K = 149.5 + 1.0 GPa and G(sub VRH) = 66.3 + 0.8 GPa, respectively. Linear least-squares regressions to the variation of bulk and shear moduli with temperature resulted in derivatives of dK/dT = -17 + 2 MPa/C and dG(sub VRH)/dT = -8 + 2 MPa/ C. Elastic anisotropy was found to remain essentially constant over the temperature range studied.

Sayir, Ali↗

Interferometric SAR modelling of near surface data to improve geological model in the Surat Basin, Australia

Here we present a study on geophysical inverse modelling for subsurface structural properties of an unconventional hydrocarbon site that was monitored previously by Interferometric Synthetic Aperture Radar (InSAR) technology for surface deformation. A static three-dimensional geomodel along with extracted property maps replicates the depth of each underlying stratigraphic unit and structural feature with the density of each geological layer. We examine the hypothesis that integration of elastic properties of each formation layer with InSAR observations in a stratified elastic medium will lead to a viscoelastic geophysical inverse problem that can be solved to estimate fractional volume change at the reservoir level. Moreover, we examine synthetic scenarios in which the elastic properties of the formations are perturbed before determining the resulting impact on the rate of surface deformation. The results show that although the slope of underlying formations, their density and depth can define the extent and pattern of a deformation signal, their properties have a marginal impact on volumetric change compared to the dense network of shallow depth Coal Seam Gas (CSG) mining wells. Besides, it is also demonstrated that the inversion of InSAR deformation maps can resolve the uncertainties associated with low-resolution seismic interpretation as well as filling the data gaps within seismic acquisitions. A significant contribution of this investigation to the geological basin modelling involves a) introducing a remote and non-invasive technology such as InSAR to improve geophysical mapping of subsurface structures such as faults in areas with sparse or no reflective seismic information, and b) applying a multi-layer viscoelastic geophysical source model for an unconventional hydrocarbon reservoir such as CSG.

58 GEOSCIENCES↗

Water-Weakening and Time-Dependent Deformation of Organic-Rich Chalks

Abstract The Ghareb Formation is a shallowly buried porous chalk in southern Israel that is being considered as a host rock for a geologic nuclear waste repository. Setup and operation of a repository will induce significant mechanical, hydrological and chemical perturbations in the Ghareb. Developing a secure repository requires careful characterization of the rock behavior to different loads. To characterize hydromechanical behavior of the Ghareb, several short- and long-term deformation experiments were conducted. Hydrostatic loading tests were conducted both dry and water-saturated, using different setups to measure elastic properties, time-dependent behavior, and permeability. A set of triaxial tests were conducted to measure the elastic properties and rock strength under differential loading at dry and water-saturated conditions. The hydrostatic tests showed the Ghareb began to deform inelastically around 12–15 MPa, a relatively low effective pressure. Long-term permeability measurements demonstrated that permeability declined with increasing effective pressure and was permanently reduced by ~ 1 order of magnitude after unloading pressure. Triaxial tests showed that water saturation significantly degrades the rock properties of the Ghareb, indicating water-weakening is a significant risk during repository operation. Time-dependent deformation is observed during hold periods of both the hydrostatic and triaxial tests, with deformation being primarily visco-plastic. The rate of deformation and permeability loss is strongly controlled by the effective pressure as well. Additionally, during holds of both hydrostatic and triaxial tests, it is observed that when water-saturated, radial strain surpassed axial strain when above effective pressures of 13–20 MPa. Thus, deformation anisotropy may occur in situ during operations even if the stress conditions are hydrostatic when above this pressure range.

58 GEOSCIENCES↗

Optical fiber technique for in-reactor mechanical properties measurement

In-reactor measurement of material properties is required for a better understanding of radiation effects on materials. We present an optical fiber based technique for measuring changes in elastic properties which involves exciting and measuring flexural vibrations in a thin cantilever beam. By exciting the beam and measuring the resonant frequency, changes in the modulus of elasticity can be monitored. The technique is demonstrated by monitoring the elastic property changes of a beam fabricated from copper, as the copper undergoes recrystallization at elevated temperature.

36 MATERIALS SCIENCE↗

Measuring the elastic tensor of a monolithic SiC hollow cylinder with resonant ultrasound spectroscopy

Resonant Ultrasound Spectroscopy (RUS) has become a standard tool in material science to measure nondestructively the elastic properties of materials. The widespread adoption of this tool for applications related to nondestructive testing and structural health monitoring in the industry and other places has been restricted thus far by some requirements imposed by RUS on the sample to be tested, in particular the fact that the sample geometry should be relatively simple (e.g., cuboid, cylinder, or sphere). Here, we use RUS to determine the baseline material properties of a hollow cylinder made of monolithic SiC, a surrogate material and geometry representing nuclear fuel cladding for this study. Typically, elastic properties of the nuclear fuel cladding samples are inspected destructively (e.g., indentation) or with acoustic techniquesrequiring multiple and cumbersome measurements. Here, a relatively new RUS approach specifically developed to measure the elastic tensor of samples with arbitrary geometries is used. The results obtained from this RUS approach are compared to values reported in the literature. As a second verification step, vibrational mode shapes computed numerically with the elastic constants are compared to those measured on the sample using a 3D laser Doppler vibrometer, showing an excellent agreement.

36 MATERIALS SCIENCE↗

Effects of Intercalating Molecules on the Polymer Properties of DNA

Atomic force microscopy (AFM) enables determination of physical properties from single DNA molecules. Insertion of aromatic molecules into the structure of DNA results in morphological changes. However, the accompanying changes to elastic properties due to this insertion are not fully understood. AFM was used to examine the morphological effects of intercalator binding and report changes in the elastic properties of intrinsically straight DNA molecules. The persistence length and polymer extension were characterized in the presence of three intercalating molecules: ethidium bromide and the less well studied chloroquine and acridine. It was found that all three intercalators significantly increased the bending persistence length. In addition, an analysis of the normal bending modes of the static molecules corroborated these results. Furthermore, this approach of measuring binding effects of intercalators on DNA physical properties using a model system of intrinsically straight DNA is applicable to other DNA binding ligands and other modes of DNA interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Stretchable nanocomposite electrodes with tunable mechanical properties by supersonic cluster beam implantation in elastomers

We demonstrate the fabrication of gold-polydimethylsiloxane nanocomposite electrodes, by supersonic cluster beam implantation, with tunable Young's modulus depending solely on the amount of metal clusters implanted in the elastomeric matrix. We show both experimentally and by atomistic simulations that the mechanical properties of the nanocomposite can be maintained close to that of the bare elastomer for significant metal volume concentrations. Moreover, the elastic properties of the nanocomposite, as experimentally characterized by nanoindentation and modeled with molecular dynamics simulations, are also well described by the Guth-Gold classical model for nanoparticle-filled rubbers, which depends on the presence, concentration, and aspect ratio of metal nanoparticles, and not on the physical and chemical modification of the polymeric matrix due to the embedding process. The elastic properties of the nanocomposite can therefore be determined and engineered a priori, by controlling only the nanoparticle concentration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical Fiber Technique for In-Reactor Mechanical Properties Measurement

In-reactor measurement of material properties is required for a better understanding of radiation effects on materials. We present an optical fiber based technique for measuring changes in elastic properties which involves exciting and measuring flexural vibrations in a thin cantilever beam. By exciting the beam and measuring the natural frequency, changes in the modulus of elasticity can be monitored. The technique is demonstrated by monitoring the elastic property changes of a beam fabricated from copper, as the copper undergoes recrystallization at elevated temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test and Analysis Correlation for a Y-Joint Specimen for a Composite Cryotank

The Composite Cryotank Technology Demonstration (CCTD) project under NASA's Game Changing Development Program (GCDP) developed space technologies using advanced composite materials. Under CCTD, NASA funded the Boeing Company to design and test a number of element-level joint specimens as a precursor to a 2.4-m diameter composite cryotank. Preliminary analyses indicated that the y-joint in the cryotank had low margins of safety; hence the y-joint was considered to be a critical design region. The y-joint design includes a softening strip wedge to reduce localized shear stresses at the skirt/dome interface. In this paper, NASA-developed analytical models will be correlated with the experimental results of a series of positive-peel y-joint specimens from Boeing tests. Initial analytical models over-predicted the experimental strain gage readings in the far-field region by approximately 10%. The over-prediction was attributed to uncertainty in the elastic properties of the laminate and a mismatch between the thermal expansion of the strain gages and the laminate. The elastic properties of the analytical model were adjusted to account for the strain gage differences. The experimental strain gages also indicated a large non-linear effect in the softening strip region that was not predicted by the analytical model. This non-linear effect was attributed to delamination initiating in the softening strip region at below 20% of the failure load for the specimen. Because the specimen was contained in a thermally insulated box during cryogenic testing to failure, delamination initiation and progression was not visualized during the test. Several possible failure initiation locations were investigated, and a most likely failure scenario was determined that correlated well with the experimental data. The most likely failure scenario corresponded to damage initiating in the softening strip and delamination extending to the grips at final failure.

Mason, Brian H.↗

Energy and mechanical properties predictions in Fe-Ni binary system by ab initio calculations

Here, the fcc random solid solutions in Fe-Ni binary system were investigated using ab initio calculations. Density functional theory (DFT) was applied along with supercells generated by the Special Quasi-Random Structure (SQS) method to predict the enthalpy of mixing and magnetic and elastic properties. The results were compared with relevant experimental and computational data produced by other groups. The effect of SQS supercell size and relaxation procedure on the predicted properties of the alloys were also studied. Our calculations show that 16-atoms SQS model provides adequate approach to the mixing energy of the alloy. However, calculation of mechanical properties requires larger supercell. Excellent agreement between experimental and calculated elastic properties was found in fcc region of Fe-Ni system.

36 MATERIALS SCIENCE↗

Photoacoustic elastic bending in thin film—Substrate system

Theoretical model for optically excited two-layer elastic plate, which includes plasmaelastic, thermoelastic, and thermodiffusion mechanisms, is given in order to study the dependence of the photoacoustic (PA) elastic bending signal on the optical, thermal, and elastic properties of thin film—substrate system. Thin film-semiconductor sample (in our case Silicon) is modeled by simultaneous analysis of the plasma, thermal, and elastic wave equations. Multireflection effects in thin film are included in theoretical model and analyzed. Relations for the amplitude and phase of electronic and thermal elastic bending in the optically excited two-layer mechanically-supported circular plate are derived. Theoretical analysis of the thermodiffusion, plasmaelastic, and thermoelastic effects in a sample-gas-microphone photoacoustic detection configuration is given. Two normalization procedures of the photoacoustic elastic bending signal in function of the modulation frequency of the optical excitation are established. Given theoretical model can be used for various photoacoustic detection configurations, for example, in the study of optical, thermal, and elastic properties of the dielectric-semiconductor or metal-semiconductor structure, etc., Theoretical analysis shows that it is possible to develop new noncontact and nondestructive experimental method—PA elastic bending method for thin film study, with possibility to obtain the optical, thermal, and elastic parameters of the film thinner than 1 μm.

36 MATERIALS SCIENCE↗

RUScal : Software for the analysis of resonant ultrasound spectroscopy measurements

Resonant ultrasound spectroscopy is used to nondestructively measure the elastic resonances of small solids to elucidate the material's elastic properties or other qualities like size, shape, or composition. In this work, we introduce the software RUScal for the purpose of determining elastic properties by analyzing the eigenfrequencies of solid specimens with common shapes, such as rectangular parallelepipeds, cylinders (solid and hollow tube), ellipsoids, and octahedrons, as well as irregularly shaped ellipsoids that can be described analytically. All symmetry classes are supported, from isotropic to triclinic, along with the option to add or remove up to three orthogonal mirror planes as well as the ability to reorient the crystal axes with respect the sample edges via Euler angles. Additional features include tools to help find initial sets of elastic constants, including grid exploration and Monte Carlo methods, a tool to analyze frequencies as a function of sample length or crystal orientation, an error analysis tool to assess fit quality, and formatting of the input and output files for batch fitting, e.g., as a function of temperature. This software was validated with published resonant ultrasound spectroscopy data for various materials, shapes, and symmetries with noted improvements in calculation time compared to finite element methods.

47 OTHER INSTRUMENTATION↗